calibrationhct.co.kr/upload/certificate/a2la scope_eng.pdf · 2020-07-28 · 2.7 μm; standard...

(A2LA Cert. No. 5825.01) Revised 08/13/2020 of 158

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2017

HCT CO., LTD 74, 578-gil, Seoicheon-ro, Majang-myeon Icheon-si, Gyungki-do 17383 South Korea

Myounglim Lee Phone: 82 31 645 6918

CALIBRATION Valid To: December 31, 2021 Certificate Number: 5825.01

In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following calibrations1, 6: I. Dimensional

Parameter/Equipment

Range CMC2 (±) Comments

Balls

Up to 100 mm

0.272 + (0.015 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Gage blocks, standard measuring machines

Dial/Cylinder Gage Testers

Up to 25 mm (25 to 100) mm

0.21 μm 0.25 μm

Gage blocks, electronic micrometers

End Bars

Up to 500 mm (500 to 1000) mm

0.132 + (0.003 × 𝑙𝑙0)2 μm 0.162 + (0.003 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Gauge blocks, electronic micrometers

Extensometers, Linear Displacement Transducers3

Up to 50 mm (50 to 100) mm (100 to 1000) mm

0.212 + (0.002 × 𝑙𝑙0)2 μm 0.782 + (0.002 × 𝑙𝑙0)2 μm 7.82 + (0.002 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Gage blocks

Filler Gage3

(0.01 to 5) mm

0.33 μm

Bench comparators


Parameter/Equipment


Gap Gages

(1 to 300) mm

2.22 + (0.005 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Gage blocks

Gage Blocks

(0.5 to 100) mm

712 + (1.3 × 𝑙𝑙0)2 nm (unit of 𝑙𝑙0 : mm)

Gage block comparators, gage blocks

Height Gages/Measuring Machines3

Up to 1000 mm

1.22 + (0.003 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Gage blocks

Standard Measuring Machines3

Up to 500 mm

0.252 + (0.0021 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Gage blocks, long gage blocks

Electronic Micrometers

Up to 0.02 mm (0.02 to 0.2) mm (0.2 to 2) mm

0.08 μm 0.16 μm 0.76 μm

Gage blocks

Height Micrometers –

Blocks Head

Up to 610 mm Up to 30 mm

1.22 + (0.003 × 𝑙𝑙0)2 μm 1.32 + (0.003 × 𝑙𝑙0)2 μm

Gage blocks Electronic micrometers

Riser Blocks

Up to 600 mm

1.22 + (0.003 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)


Laser Scan Micrometers3

(1 to 55) mm

0.56 μm

Pin gage

Standard Tape Rules, Peripheral Gages

Up to 13 m (13 to 26) m (26 to 39) m (39 to 50) m

0.152 + (0.009 × 𝑙𝑙0)2 mm 0.172 + (0.011 × 𝑙𝑙0)2 mm 0.282 + (0.011 × 𝑙𝑙0)2 mm 0.482 + (0.011 × 𝑙𝑙0)2 mm (unit of 𝑙𝑙0 : m)

Laser interferometers, tape measure, calibration system


Parameter/Equipment


Cylindrical Plug/Pin Gages3, Thread Measuring Wire Gages3

(0.1 to 100) mm

0.292 + (0.003 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Standard measuring machines

Radius Gages

Up to 50 mm

3.0 μm

Profile projectors

Cylindrical Ring Gages

(1 to 100) mm

0.592 + (0.003 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Standard measuring machines, standard ring gages

Step Gages

Up to 1000) mm

1.22 + (0.002 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)


Taper Thickness Gages

(0.1 to 60) mm

0.03 mm

Profile projectors

Ultrasonic Thickness Gages3

Up to 100 mm

3.6 μm

Ultrasonic thickness specimens

Ultrasonic/Coating Thickness Specimens –

Coating Ultrasonic


1.4 μm 1.42 + (0.002 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Gage blocks, standard measuring machines, electronic micrometers

Coating Thickness Testers3

Up to 0.25 mm (0.25 to 1.05) mm (1.05 to 3.7) mm (3.7 to 7.9) mm

1.5 μm 2.0 μm 6.9 μm 6.9 μm

Coating thickness specimens

Torque Arms –

Torque Arm

Wire


4.22 + (0.010 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm) 0.7 μm

Contact coordinate measuring machines Standard measuring machines


Parameter/Equipment

Range

CMC2 (±)

Comments

Bevel protractors –

Angle Accuracy

Angle of Accessories

(0 to 90) ° (90 to 360) ° (0 to 360) °

1.3´ 2.0´ 2.3´

Angle gage blocks, precision surface plates, profile projectors

Plate/Square/Electric Levels –

Angle

Squareness Flatness

± 200˝ ± 1000˝ ± 2000˝ Up to 300 mm 300 mm × 60 mm

0.3˝ 0.5˝ 0.9˝ 2.2 μm 0.9 μm

Fine angle generators, electronic micrometers, squareness testers, precision surface plates

Precisions Squares –

Squareness

Parallelism Straightness

Up to 450 mm Up to 450 mm Up to 450 mm

1.22 + (0.002 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm) 1.2 μm 2.9 μm

Cylindrical square, squareness testers, precision squares

Form Testers3 –

Z-axis X-axis Angle

Up to 60 mm Up to 200 mm Up to 180 °

0.16 μm 0.572 + (0.002 × 𝑙𝑙0)2 μm 1.3´

Standard scales Gage blocks Angle gage blocks

Optical Flats

(10 to 130) mm

0.06 μm

Optical flats, Monochromatic light sources


Parameter/Equipment


Optical Parallels –

Flatness

Parallelism

(10 to 30) mm (10 to 30) mm

0.066 μm 0.080 μm

Optical flats, monochromatic light sources, gage block comparators

Parallel blocks3 –

Parallelism Flatness Difference of Blocks


1.2 μm 1.2 μm 1.8 μm

Electronic micrometers Precision surface plate Test bars

Precision Surface Plates3 – Area

Up to 2500 cm2

(2500 to 5000) cm2

(5000 to 10 000) cm2

(10 000 to 15 000) cm2

(15 000 to 30 000) cm2

(30 000 to 60 000) cm2

1.5 μm 1.9 μm 2.3 μm 2.5 μm 3.4 μm 4.2 μm

Electric levels

Roundness Measurement Instruments3 –

Accuracy of Detector Rotation Accuracy of Circumference Direction Rotation Accuracy of Shaft Direction Straightness

Up to 1000 μm (0 to 360) ° (0 to 360) ° Up to 360 mm

0.50 μm 16 nm 16 nm 1.1 μm

Roundness standard specimens, cylindrical squares, optical flats

Straight Rules

Up to 3000 mm

0.292 + (0.009 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Laser interferometers, tape measure calibration system


Parameter/Equipment

Range CMC2, 5 (±) Comments

Contact Coordinate Measuring Machines3 –

Accuracy

Straightness Squareness


0.532 + (0.003 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm) 2.1 μm 3.1˝

Step gages, precision squares, straight edges

Non-Contact Coordinate Measuring Machines3 – Accuracy

Up to 1000 mm

0.432 + (0.003 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Standard scales

Measuring Microscopes, Profile Projectors3 –

Length accuracy

Right Angle Accuracy Magnification Accuracy Squareness Accuracy

Up to 300 mm (0 to 360) ° ×2 to ×100 Up to 300 mm

0.452 + (0.003 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm) 1.7´ 3.2 × 10-4 3.6 μm

Standard scales, precision squares

Micro Measuring Microscopes3

Up to 50 mm

2.7 μm

Standard scales

Thread Plug Gages –

External Diameter Effective Diameter Pitch Half Angle

Up to 100 mm Up to 100 mm (0.2 to 6) mm (0 to 45) °

0.48 μm 1.6 μm 1.2 μm 1.8´

Standard measuring machines, thread measuring wires, profile projectors

V-blocks, Box blocks –

Flatness Parallelism Gradient Difference of Both Parts Squareness

Up to 150 mm Up to 150 mm Up to 150 mm Up to 150 mm Up to 150 mm

0.80 μm 0.95 μm 0.56 μm 1.1 μm 2.02 + (0.003 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Pin gages, test bars, precision surface plates, electronic micrometers


Parameter/Equipment


Inside/Outside/Gear Tooth Calipers3, Caliper Gages3

Up to 150 mm (150 to 1500) mm


Gage blocks

Cylinder Gages3/Bore Gages3

Up to 800 mm (0.5 to 18.5) mm

0.96 μm 0.76 μm

Dial gage testers, gage blocks

Depth Gages3 and Depth Micrometers3

Up to 300 mm (300 to 1000) mm


Gage blocks

Dial/Digital Gages3

Up to 50 mm (50 to 150) mm


Gage blocks

Micrometer Heads

Up to 50 mm

0.61 μm


3-Point Micrometers3

(1 to 200) mm

3.4 μm

Standard ring gages, precision surface plates

Inside Micrometers3

(5 to 300) mm (300 to 1500) mm


Gage blocks

Outside Micrometers3

Up to 25 mm (25 to 100) mm (100 to 1500) mm

0.362 + (0.004 × 𝑙𝑙0)2 μm 0.792 + (0.004 × 𝑙𝑙0)2 μm 2.52 + (0.004 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Gage blocks

Standard Sieves –

Sieve Opening Wire Rod Diameter

(0.01 to 8) mm (0.01 to 125) mm

1.6 μm 2.6 μm

Profile projectors


Parameter/Equipment


Welding Gauges –

Height/Depth Measuring Scale Thick Measuring Scale Rule Measuring Scale Angle Measuring Scale Taper Measuring Scale

Up to 100 mm Up to 16 mm Up to 50 mm (0 to 90) ° Up to 7 mm

0.009 mm 0.009 mm 0.096 mm 0.13° 0.096 mm

Profile projectors

Length – Measure

(0 to 500) mm

1.52 + (0.010 × 𝑙𝑙0)2 μm (unit of 𝑙𝑙0 : mm)

Contact coordinate measuring machines

Angle – Measure

(0 to 360) ˚

2.2 arc min

Profile projector

II. Mechanical

Parameter/Equipment


Counter Beam Balances

Up to 311 g (311 to 2610) g (2.61 to 20) kg

9.6 mg 82 mg 0.82 g

Standard weights

Direct Reading Balances

Up to 160 g

0.19 mg

Standard weights

Electric Balances

Up to 20 g (20 to 200) g (200 to 2000) g (1 to 26) kg (26 to 60) kg (60 to 100) kg (100 to 150) kg (150 to 200) kg (200 to 300) kg (300 to 600) kg

0.062 mg 0.19 mg 1.8 mg 21 mg 0.72 g 1.7 g 6.2 g 12 g 58 g 0.12 kg

Standard weights


Parameter/Equipment


Platform Scale Balances

Up to 20 kg

(20 to 200) kg

1.2 g 0.058 kg

Standard weights

Spring Scale Balances

Up to 1 kg (1 to 2) kg (2 to 5) kg (5 to 10) kg (10 to 30) kg (30 to 50) kg

2.9 g 5.8 g 12 g 29 g 58 g 0.12 kg

Standard weights

Weights, F1 Class

1 mg 2 mg 5 mg 10 mg 20 mg 50 mg 100 mg 200 mg 500 mg 1 g 2 g 5 g 10 g 20 g 50 g 100 g 200 g 500 g 1 kg 2 kg 5 kg 10 kg 20 kg

4.6 μg 4.6 μg 4.6 μg 5.1 μg 5.1 μg 5.8 μg 6.6 μg 7.4 μg 9.1 μg 11 μg 14 μg 17 μg 21 μg 27 μg 36 μg 55 μg 0.11 mg 0.29 mg 0.55 mg 1.1 mg 2.9 mg 5.5 mg 11 mg

Standard weights, mass comparators


Parameter/Equipment

Range CMC2, 4, 5 (±) Comments

Mass – Measure

(0 to 50) mg (50 to 500) mg (0.5 to 5) g (5 to 50) g (50 to 100) g (100 to 200) g (200 g to 500) g (0.5 to 1) kg (1 to 2) kg (2 to 5) kg (5 to 10) kg (10 to 20) kg (20 to 26) kg (26 to 35) kg

0.006 mg 0.009 mg 0.017 mg 0.036 mg 0.055 mg 0.10 mg 0.29 mg 0.54 mg 1.0 mg 2.8 mg 5.4 mg 10 mg 13 mg 88 mg

Standard weights, Mass comparators

Force Measuring Devices

(0.5 to 5) kN (5 to 10) kN (10 to 20) kN (20 to 50) kN (50 to 100) kN

4.1 × 10-5

3.1 × 10-4 3.0 × 10-4 3.6 × 10-4 4.0 × 10-4

Hydraulic force standards, deadweight force standards

Force – Measuring Equipment

(0 to 500) N (0.5 to 5) kN (5 to 10) kN (10 to 20) kN (20 to 50) kN (50 to 100) kN

0.15 % 0.0041 % 0.031 % 0.03 % 0.036 % 0.04 %

Weight set, deadweight force standards, hydraulic force standards

Force – Measure

Compression Tension

(0 to 1000) kN (0 to 200) kN

0.28 % 0.17 %

Electric force gauge


Parameter/Equipment


Tension/Compression Testing Machines3

Compression

Tension

Up to 10 N (10 to 20) N (20 to 50) N (50 to 100) N (100 to 200) N (200 to 500) N (500 to 1000) N (1 to 2) kN (2 to 5) kN (5 to 10) kN (10 to 20) kN (20 to 50) kN (50 to 100) kN (100 to 200) kN (200 to 500) kN (500 to 1000) kN Up to 50 N (50 to 100) N (100 to 200) N (200 to 500) N (500 to 1 000) N (1 to 2) kN (2 to 5) kN (5 to 10) kN (10 to 20) kN (20 to 50) kN (50 to 100) kN (100 to 200) kN

1.5 × 10-3

1.4 × 10-3

1.3 × 10-3

1.3 × 10-3

1.4 × 10-3

1.4 × 10-3

1.5 × 10-3

1.7 × 10-3

1.4 × 10-3

1.6 × 10-3

1.8 × 10-3

1.4 × 10-3

1.4 × 10-3

1.5 × 10-3

1.5 × 10-3

1.7 × 10-3

1.4 × 10-3

1.4 × 10-3

1.3 × 10-3

1.3 × 10-3

1.4 × 10-3

1.6 × 10-3

1.3 × 10-3

1.5 × 10-3

1.7 × 10-3

1.4 × 10-3

1.6 × 10-3

1.6 × 10-3

Electric force measuring devices

Push-Pull Gauges

(0.2 to 50) N (50 to 1000) N (1000 to 2000) N (2000 to 5000) N

1.5 × 10-3

1.3 × 10-3

1.6 × 10-3

1.5 × 10-3

Deadweight force standards, weights

Torque Measuring Devices

(0.05 to 100) N·m

7.1 × 10-3

Weights, torque arms


Parameter/Equipment


Torque Wrenches/Drivers3 –

Clockwise

Counterclockwise

(0.1 to 1) N·m (1 to 2.5) N·m (2.5 to 5) N·m (5 to 10) N·m (10 to 25) N·m (25 to 50) N·m (50 to 100) N·m (100 to 250) N·m (250 to 500) N·m (500 to 1000) N·m (1000 to 2000) N·m (0.1 to 1) N∙m (1 to 2.5) N·m (2.5 to 5) N·m (5 to 10) N·m (10 to 25) N·m (25 to 50) N·m (50 to 100) N·m (100 to 250) N·m (250 to 500) N·m (500 to 1000) N·m (1000 to 2000) N·m

1.2 × 10-2

9.6 × 10-3

7.0 × 10-3

5.2 × 10-3

3.8 × 10-3

4.0 × 10-3

6.9 × 10-3

3.6 × 10-3

3.2 × 10-3

5.1 × 10-3

9.4 × 10-3

1.1 × 10-2

1.0 × 10-2

7.4 × 10-3

5.0 × 10-3

4.8 × 10-3

4.0 × 10-3

1.0 × 10-2

2.9 × 10-3

2.9 × 10-3

5.0 × 10-3

9.8 × 10-3

Torque testers

Torque – Measure

(0 to 1) N·m (1 to 2.5) N·m (2.5 to 5) N·m (5 to 10) N·m (10 to 25) N·m (25 to 50) N·m (50 to 100) N·m (100 to 250) N·m (250 to 500) N·m (500 to 1000) N·m (1000 to 2000) N·m

0.99 % 1.0 % 0.62 % 0.52 % 0.43 % 0.40 % 1.0 % 0.46 % 0.33 % 0.45 % 0.98 %

Torque measuring device

Absolute Pressure Gauges

60 kPa abs to 7 MPa abs

1.5 × 10-4

Pressure controllers

Compound Pressure Gauges3

-95 kPa to 7 MPa

2.4 × 10-3

Pressure calibrators, dead weight testers


Parameter/Equipment

Range CMC2, 3, 4, 5 (±) Comments

Pneumatic Differential Pressure Gauges3

Up to 7 MPa

1.6 × 10-4

Pressure calibrators, dead

weight testers

Pressure Generators / Controllers –

Pneumatic

Hydraulic

Pressure Recorders:

Pneumatic

Hydraulic

Up to 350 kPa (0.35 to 5) MPa (5 to 10) MPa (0.5 to 200) MPa Up to 350 kPa (0.35 to 5) MPa (5 to 10) MPa (0.5 to 200) MPa

3.2 × 10-4

1.3 × 10-4

2.0 × 10-4

1.3 × 10-4

9.2 × 10-4

1.5 × 10-3

2.9 × 10-3

1.6 × 10-3

Pressure calibrators, pneumatic pressure balance, hydraulic pressure balance

Pressure Transducers / Transmitters –

Pneumatic Hydraulic

Up to 350 kPa (0.35 to 5) MPa (5 to 10) MPa 60 kPa abs to 7 MPa abs (0.5 to 200) MPa

4.1 × 10-4

3.6 × 10-4

3.7 × 10-4

3.7 × 10-4

3.3 × 10-4


Dial Type Vacuum Gauges

(-95 to 0) kPa

6.9 × 10-4

Pressure calibrators

Water Depth Meters

Up to 2 MPa

1.5 × 10-4


Pressure – Measure and Measuring Equipment

Gauge pressure

Absolute pressure

(0 to 350) kPa (0.35 to 5) MPa (5 to 10) MPa (10 to 200) MPa (60 to 135) kPa abs. (135 to 7000) kPa abs.

0.071 % 0.036 % 0.090 % 0.015 % 0.010 % 0.050 %



Parameter/Equipment


Vacuum – Measure and Measuring Equipment

(-95 to 0) kPa

0.051 %


III. Fluid Quantities

Parameter/Equipment


Anemometers –

Hot-Wire

Pitot Tube

Vane

(0.1 to 2) m/s (2 to 55) m/s (0.1 to 2) m/s (2 to 55) m/s (0.1 to 2) m/s (2 to 55) m/s

5.8 × 10-2 4.4 × 10-3 5.8 × 10-2 4.4 × 10-3

5.8 × 10-2 4.4 × 10-3

ILA / LDV SONDE FP50US

Particle Counters –

Airborne Particle Counter3

Laser Reference Voltage Flow Rate Threshold Voltage

Counting Efficiency3

CPC OPC

Liquid Particle Counter

Laser Reference Voltage Flow Rate Threshold Voltage

(0 to 10) V (0 to 100) L/min (0 to 6) V (6 to 10) V (0 to 1.0) μm (0.1 to 1.0) μm (0 to 10) V (0 to 300) mL/min (0 to 6) V (6 to 10) V

4.2 × 10-3

2.3 × 10-2

2.1 × 10-3

4.2 × 10-3

3.0 % 4.7 % 4.2 × 10-3

2.8 × 10-2

2.1 × 10-3

4.2 × 10-3

Fluke 175 TSI 4043H Fluke 175 TSI 3068B TSI 3772, PMS LASAIRⅡ-110, CRM standard size particles Fluke 175, Matheson FM-1050, Matheson FM1050S-V, PMS / FC-100CRM standard size particles

Particle Dilution Systems3 –

PCRF (Particle Concentration Reduction Factor)

(30 to 100) nm

8.2 × 10-2

TSI 3776, 3772 AVL LIST GmbH AVL499 APG


Parameter/Equipment


Dynamic Viscometers – Rotational Viscometers

(2.5 to 200 000) mPa·s

1.7 × 10-2

Polyscience / AD29VB3S-A13K Wika / CTR2000 viscosity standard

IV. Time & Frequency

Parameter/Equipment


Frequency Standards – Timebase Frequency

100 kHz to 10 MHz

4.5 × 10-13

Odetics 425-311 and HP 53132A

General Frequency Sources3 – Timebase Frequency

100 kHz to 100 MHz

2.6 × 10-12

Odetics 425-311 and HP 53132A

Frequency Meters/Counters –

Input Frequency Timebase Frequency

DC to 3 GHz (3 to 40) GHz 100 kHz to 10 MHz

6.1 × 10-12 0.58 Hz 2.6 × 10-12

Odetics 425-311 and H.P 53132A Agilent E8257D


Parameter/Equipment


Time Interval Sources –

Time Interval

Frequency

(0.1 to 1) ns (1 to 10) ns (10 to 100) ns 100 ns to 1 μs (1 to 10) μs (10 to 100) μs 100 μs to 1 ms (1 to 10) ms (10 to 100) ms 100 ms to 5 s (0.1 to 1) Hz (1 to 10) Hz (10 to 100) Hz 100 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz 100 kHz to 1 MHz (1 to 10) MHz (10 to 100) MHz 100 MHz to 1 GHz

5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7

5.8 × 10-7

Odetics 425-311 and H.P 53132A

Time Interval Meters/Stop Watches/Timers

Time

Period

1 ms to 86 400 s (1 to 10 000) s

7.2 × 10-8 5.8 × 10-6

Witschi Q-Test 6000 H.P 5334B Agilent 33250A

Photo Tachometers/ Stroboscopes

(1 to 300) min⁻¹ (300 to 6000) min⁻¹ (6000 to 100 000) min⁻¹

6.2 × 10-3 min⁻¹ 6.2 × 10-2 min⁻¹ 6.2 × 10-1 min⁻¹

Odetics 425-311 Agilent 33250A

Standard RPM Generators

(1 to 1000) min⁻¹ (1000 to 100 000) min⁻¹

6.2 × 10-2 min⁻¹ 6.2 × 10-1 min⁻¹

Odetics 425-311 H.P 53132A Testo 470

Contact Type Tachometers

(1 to 4000) min⁻¹

6.1 × 10-2 min⁻¹

Odetics 425-311 Kriss P01C


Parameter/Equipment


Photo Tachometers/ Stroboscopes

(1 to 300) min⁻¹ (300 to 6000) min⁻¹ (6000 to 100 000) min⁻¹

6.2 × 10-3 min⁻¹ 6.2 × 10-2 min⁻¹ 6.2 × 10-1 min⁻¹

Odetics 425-311 Agilent 33250A

Standard RPM Generators

(1 to 1000) min⁻¹ (1000 to 100 000) min⁻¹

6.2 × 10-2 min⁻¹ 6.2 × 10-1 min⁻¹

Odetics 425-311 H.P 53132A Testo 470

Contact Type Tachometers

(1 to 4000) min⁻¹

6.1 × 10-2 min⁻¹

Odetics 425-311 Kriss P01C

Wow-Flutter Generators – Wow-Flutter Deflection

Frequency

Level

(0.01 to 3) % 0.1 Hz to 99.99 kHz 100 mV to 10 V

1.9 × 10-5 5.8 × 10-4

8.0 × 10-3

Odetics 425-311, HP 53132A, HP 34401A, Tektronix 540A, HP 8903B

Wow-Flutter Meters –

Wow-Flutter Deflection

Input Frequency

Output Frequency

CCIR Pulse

0.01 % 0.03 % 0.1 % 0.3 % 1 % 3 % 10 Hz 99.99 kHz 3.00 kHz 3.15 kHz (10 to 100) ms

2.4 × 10-4 4.6 × 10-4 1.6 × 10-3 4.6 × 10-3 1.5 × 10-2 4.5 × 10-2 0.58 Hz 5.8 Hz 0.58 Hz 0.58 Hz 1.5 × 10-2

Meguro MWS-672, Odetics 425-311, HP 53132A


V. Electrical – DC/Low Frequency

Parameter/Equipment


DC Ammeters –

DC Current

10 pA (10 to 40) pA (40 to 80) pA (80 to 100) pA (100 to 400) pA (400 to 800) pA (0.8 to 4) nA (4 to 8) nA (8 to 10) nA (10 to 40) nA (40 to 80) nA (80 to 100) nA (100 to 400) nA (400 to 800) nA (0.8 to 1) μA (1 to 4) μA (4 to 10) μA (10 to 40) μA (40 to 80) μA (80 to 100) μA (100 to 400) μA (400 to 800) μA (0.8 to 1) mA (1 to 4) mA (4 to 8) mA (8 to 10) mA (10 to 40) mA (40 to 80) mA (80 to 100) mA (100 to 800) mA (0.8 to 1) A (1 to 4) A (4 to 8) A (8 to 10) A (10 to 80) A (80 to 100) A

7.1 fA 16 fA 29 fA 36 fA 48 fA 95 fA 0.12 pA 0.21 pA 0.27 pA 1.3 pA 2.2 pA 2.7 pA 12 pA 24 pA 7.0 nA 7.2 nA 7.4 nA 9.1 nA 11 nA 12 nA 29 nA 44 nA 51 nA 0.26 μA 0.40 μA 0.48 μA 3.1 μA 5.1 μA 8.6 μA 15 μA 0.13 mA 0.83 mA 1.1 mA 1.2 mA 36 mA 37 mA

Fluke 5730A, Fluke 52120A, standard resistances


Parameter/Equipment


DC Ammeters –

DC Current (cont)

-10 pA (-10 to -40) pA (-40 to -80) pA (-80 to -100) pA (-100 to -400) pA (-400 to -800) pA (-0.8 to -4) nA (-4 to -8) nA (-8 to -10) nA (-10 to -40) nA (-40 to -80) nA (-80 to -100) nA (-100 to -400) nA (-400 to -800) nA (-0.8 to -1) μA (-1 to -4) μA (-4 to -10) μA (-10 to -40) μA (-40 to -80) μA (-80 to -100) μA (-100 to -400) μA (-400 to -800) μA (-0.8 to -1) mA (-1 to -4) mA (-4 to -8) mA (-8 to -10) mA (-10 to -40) mA (-40 to -80) mA (-80 to -100) mA (-100 to -800) mA (-0.8 to -1) A (-1 to -4) A (-4 to -8) A (-8 to -10) A (-10 to- 80) A (-80 to -100) A

7.1 fA 16 fA 29 fA 36 fA 48 fA 95 fA 0.12 pA 0.21 pA 0.27 pA 1.3 pA 2.2 pA 2.7 pA 12 pA 24 pA 7.0 nA 7.2 nA 7.4 nA 9.1 nA 11 nA 12 nA 29 nA 44 nA 51 nA 0.26 μA 0.40 μA 0.48 μA 3.1 μA 5.1 μA 8.6 μA 15 μA 0.13 mA 0.83 mA 1.1 mA 1.2 mA 36 mA 37 mA

Fluke 5730A, Fluke 52120A, standard resistances


Parameter/Equipment


Transconductance Amplifiers –

DC Current

0 μA (0 to 40) μA (40 to 80) μA (80 to 100) μA (100 to 400) μA (400 to 800) μA (0.8 to 1) mA (1 to 4) mA (4 to 8) mA (8 to 10) mA (10 to 40) mA (40 to 80) mA (80 to 100) mA (100 to 400) mA (400 to 800) mA (0.8 to 1) A (1 to 4) A (4 to 8) A (8 to 10) A (10 to 40) A (40 to 80) A (80 to 100) A (0 to -40) μA (-40 to -80) μA (-80 to -100) μA (-100 to -400) μA (-400 to -800) μA (-0.8 to -1) mA (-1 to -4) mA (-4 to -8) mA (-8 to -10) mA (-10 to -40) mA (-40 to -80) mA (-80 to -100) mA (-100 to -400) mA (-400 to -800) mA (-0.8 to -1) A (-1 to -4) A (-4 to -8) A (-8 to -10) A (-10 to -40) A (-40 to -80) A (-80 to -100) A

1.2 nA 1.5 nA 2.3 nA 2.8 nA 13 nA 22 nA 26 nA 0.12 μA 0.21 μA 0.25 μA 1.3 μA 2.2 μA 2.6 μA 14 μA 23 μA 28 μA 0.16 mA 0.28 mA 0.34 mA 2.0 mA 3.7 mA 4.5 mA 1.5 nA 2.3 nA 2.8 nA 13 nA 22 nA 26 nA 0.12 μA 0.21 μA 0.25 μA 1.3 μA 2.2 μA 2.6 μA 14 μA 23 μA 28 μA 0.16 mA 0.28 mA 0.34 mA 2.0 mA 3.7 mA 4.5 mA

Fluke 8508A, Fluke 5730A, current shunts


Parameter/Frequency


Transconductance Amplifiers (cont)

AC Current 50 Hz

(50 to 100) Hz

100 μA (100 to 400) μA (400 to 800) μA (0.8 to 1) mA (1 to 4) mA (4 to 8) mA (8 to 10) mA (10 to 40) mA (40 to 80) mA (80 to 100) mA (100 to 400) mA (400 to 800) mA (0.8 to 1) A (1 to 4) A (4 to 8) A (8 to 10) A (10 to 40) A (40 to 80) A (80 to 100) A 100 μA (100 to 400) μA (400 to 800) μA (0.8 to 1) mA (1 to 4) mA (4 to 8) mA (8 to 10) mA (10 to 40) mA (40 to 80) mA (80 to 100) mA (100 to 400) mA (400 to 800) mA (0.8 to 1) A (1 to 4) A (4 to 8) A (8 to 10) A (10 to 40) A (40 to 80) A (80 to 100) A

21 nA 93 nA 0.13 μA 0.15 μA 0.89 μA 1.3 μA 1.4 μA 9.0 μA 13 μA 14 μA 90 μA 0.12 mA 0.14 mA 0.91 mA 1.3 mA 1.5 mA 9.6 mA 14 mA 17 mA 21 nA 93 nA 0.13 μA 0.15 μA 0.89 μA 1.3 μA 1.4 μA 9.0 μA 13 μA 14 μA 90 μA 0.12 mA 0.14 mA 0.91 mA 1.3 mA 1.5 mA 9.6 mA 14 mA 17 mA



Parameter/Frequency



AC Current 100 Hz to 1 kHz (1 to 10) kHz

100 μA (100 to 400) μA (0.4 to 1) mA (1 to 4) mA (4 to 8) mA (8 to 10) mA (10 to 40) mA (40 to 80) mA (80 to 100) mA (100 to 400) mA (400 to 800) mA (0.8 to 1) A (1 to 4) A (4 to 8) A (8 to 10) A (10 to 40) A (40 to 80) A (80 to 100) A 100 μA (100 to 400) μA (400 to 800) μA (0.8 to 1) mA (1 to 4) mA (4 to 8) mA (8 to 10) mA (10 to 40) mA (40 to 80) mA (80 to 100) mA (100 to 400) mA (400 to 800) mA (0.8 to 1) A (1 to 4) A (4 to 8) A (8 to 10) A (10 to 40) A (40 to 80) A (80 to 100) A

21 nA 86 nA 0.12 μA 0.83 μA 1.1 μA 1.2 μA 8.3 μA 11 μA 12 μA 83 μA 0.11 mA 0.12 mA 0.84 mA 1.1 mA 1.3 mA 9.0 mA 13 mA 15 mA 21 nA 96 nA 0.14 μA 0.16 μA 0.89 μA 1.3 μA 1.4 μA 9.0 μA 13 μA 14 μA 90 μA 0.12 mA 0.14 mA 0.99 mA 1.5 mA 1.8 mA 13 mA 21 mA 26 mA



Parameter/Frequency



AC Current (10 to 100) kHz

100 μA (100 to 400) μA (400 to 800) μA (0.8 to 1) mA (1 to 4) mA (4 to 8) mA (8 to 10) mA (10 to 40) mA (40 to 80) mA (80 to 100) mA (100 to 400) mA (400 to 800) mA (0.8 to 1) A (1 to 4) A (4 to 8) A (8 to 10) A (10 to 40) A (40 to 80) A (80 to 100) A

0.11 μA 0.53 μA 0.77 μA 0.89 μA 5.3 μA 7.6 μA 8.8 μA 53 μA 76 μA 88 μA 0.53 mA 0.76 mA 0.87 mA 5.4 mA 7.7 mA 8.9 mA 54 mA 79 mA 91 mA


DC Voltage/Current Calibrators –

DC Current Source

0.1 mA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA (0.1 to 1) A (1 to 10) A (10 to 100) A -0.1 mA (-0.1 to -1) mA (-1 to -10) mA (-10 to -100) mA (-0.1 to -1) A (-1 to -10) A (-10 to -100) A

2.0 nA 2.0 × 10-5 1.3 × 10-5 1.5 × 10-5 1.3 × 10-5 1.2 × 10-4 6.3 × 10-4 2.0 nA 2.0 × 10-5 1.3 × 10-5 1.5 × 10-5 1.3 × 10-5 1.2 × 10-4 6.3 × 10-4

Fluke 8508A, current shunts


Parameter/Equipment


DC Voltage/Current Calibrators – (cont)

DC Voltage Source

100 mV (0.1 to -1) V (1 to 10) V (10 to 100) V (100 to 1 000) V -100 mV (-0.1 to -1) V (-1 V to -10) V (-10 to -100) V (-100 to -1000) V

1.2 nV 1.2 × 10-5 9.2 × 10-6 1.0 × 10-5 1.2 × 10-5 1.2 nV 1.2 × 10-5 9.2 × 10-6 1.0 × 10-5 1.2 × 10-5

Fluke 8508A, current shunts

Electrical Temperature Calibrators –

DC Current

DC Voltage

Resistance

DC Current (Meter)

DC Voltage (Meter)

1 mA (1 to10) mA (10 to 30) mA (-10 to 0) mV 0 mV (0 to 10) mV (10 to 100) mV (0.1 to 30) V 10 Ω (10 to 100) Ω (0.1 to 10) kΩ (10 to 100) kΩ 1 mA (1 to 10) mA (10 to 20) mA (20 to 30) mA (-10 to 0) mV 0 mV (0 to 10) mV (10 to 100) mV (0.1 to 10) V (10 to 100) V

78 nA 1.6 × 10-5 9.3 × 10-5 8.4 × 10-4 0.52 μV 8.4 × 10-4 8.5 × 10-5 6.2 × 10-5 0.13 mΩ 1.3 × 10-5 1.2 × 10-5 1.3 × 10-5 98 nA 9.8 × 10-5 7.5 × 10-5 1.0 × 10-4 1.2 × 10-3 0.71 μV 1.2 × 10-3 1.2 × 10-4 6.2 × 10-5 1.4 × 10-5

Fluke 5730A Fluke 5730A Fluke 5730A Fluke 8508A Fluke 8508A


Parameter/Equipment


Electrical Temperature Calibrators – (cont)

Resistance (Meter)

10 Ω (10 to 100) Ω (0.1 to 1) kΩ (1 to 10) kΩ (10 to 100) kΩ

0.72 mΩ 7.2 × 10-5 2.2 × 10-5 1.8 × 10-5 1.9 × 10-5

Fluke 8508A

DC Current Shunts

0.1 mΩ (0.2 to 0.333) mΩ (0.333 to 0.5) mΩ (0.5 to 8) mΩ (8 to 10) mΩ (10 to 16) mΩ (16 to 80) mΩ (0.08 to 0.1) Ω (0.1 to 0.16) Ω (0.16 to 0.4) Ω (0.4 to 0.8) Ω (0.8 to 1) Ω (1 to 1.6) Ω (1.6 to 4) Ω (4 to 8) Ω (8 to 10) Ω (10 to 16) Ω (16 to 40) Ω (40 to 80) Ω (80 to 100) Ω (100 to 800) Ω (800 to 1000) Ω

1.6 × 10-4 1.5 × 10-4 1.6 × 10-4 1.5 × 10-4 4.0 × 10-4 1.4 × 10-5 1.6 × 10-4 1.1 × 10-4 2.1 × 10-4 1.0 × 10-4 1.1 × 10-4 7.0 × 10-5 2.2 × 10-4 5.5 × 10-4 6.3 × 10-5 5.0 × 10-5 1.3 × 10-4 3.3 × 10-4 1.3 × 10-4 1.0 × 10-4 6.3 × 10-5 6.0 × 10-5

Fluke 8508A Fluke 5730A and 52120A Current Shunts


Parameter/Equipment


Galvanometers/Null Detectors –

DC Voltage

(3 to 10) μV (10 to 30) μV (30 to 100) μV (100 to 300) μV (0.1 to 1) mV (1 to 3) mV (3 to 10) mV (10 to 30) mV (30 to 100) mV (100 to 300) mV (0.3 to 1) V (1 to 3) V (3 to 10) V (10 to 30) V (30 to 100) V (100 to 300) V (300 to 1000) V

5.8 × 10-3 9.6 × 10-3 5.8 × 10-3 9.6 × 10-3 5.8 × 10-3 9.6 × 10-3 5.8 × 10-3 9.6 × 10-3 5.8 × 10-3 9.6 × 10-3 5.8 × 10-3 9.6 × 10-3 5.8 × 10-3 9.6 × 10-3 5.8 × 10-3 9.6 × 10-3 5.8 × 10-3

Fluke 5730A Ballantine 1625A

DC Power Supplies –

DC Voltage

0 V (0 to 80) mV (80 to 100) mV (100 to 400) mV (400 to 800) mV (0.8 to 1) V (1 to 4) V (4 to 8) V (8 to 10) V (10 to 40) V (40 to 80) V (80 to 100) V (100 to 800) V (800 to 1000) V

0.79 μV 1.1 μV 1.2 μV 8.6 μV 8.9 μV 9.3 μV 66 μV 76 μV 80 μV 0.89 mV 0.94 mV 1.0 mV 11 mV 12 mV

Fluke 8508A


Parameter/Equipment


DC Power Supplies – (cont)

DC Voltage

DC Current

(0 to -40) mV (-80 to -100) mV (-100 to -400) mV (-400 to -800) mV (-0.8 to -1) V (-1 to -4) V (-4 to -8) V (-8 to -10) V (-10 to -40) V (-40 to -80) V (-80 to -100) V (-100 to -400) V (-800 to -1000) V 0 A (0 to 40) μA (40 to 80) μA (80 to 100) μA (100 to 400) μA (400 to 800) μA (0.8 to 1) mA (1 to 4) mA (4 to 8) mA (8 to 10) mA (10 to 40) mA (40 to 80) mA (80 to 100) mA (100 to 400) mA (400 to 800) mA (0.8 to 1) A (1 to 4) A (4 to 8) A (8 to 10) A (10 to 40) A (40 to 80) A (80 to 100) A (100 to 200) A (200 to 300) A (300 to 500) A (500 to 1000) A

1.1 μV 1.2 μV 8.6 μV 8.9 μV 9.3 μV 66 μV 76 μV 80 μV 0.89 mV 0.94 mV 1.0 mV 11 mV 12 mV 0.88 nA 1.6 nA 2.3 nA 2.7 nA 14 nA 22 nA 26 nA 0.14 μA 0.22 μA 0.26 μA 1.4 μA 2.2 μA 2.7 μA 15 μA 23 μA 28 μA 0.16 mA 0.27 mA 0.34 mA 2.1 mA 3.7 mA 4.5 mA 41 mA 61 mA 0.11 A 0.22 A

Fluke 8508A Fluke 8508A current shunts


Parameter/Equipment


DC Power Supplies – (cont)

DC Current Ripple

Load Regulation

(0 to -40) μA (-40 to -80) μA (-80 to -100) μA (-100 to -400) μA (-400 to -800) μA (-0.8 to -1) mA (-1 to -4) mA (-4 to -8) mA (-8 to -10) mA (-10 to -40) mA (-40 to -80) mA (-80 to -100) mA (-100 to -400) mA (-400 to -800) mA (-0.8 to -1) A (-1 to -4) A (-4 to -8) A (-8 to -10) A (-10 to -40) A (-40 to -80) A (-80 to -100) A (-100 to -200) A (-200 to -300) A (-300 to -500) A (-500 to -1000) A 1 mV (1 to 5) mV (5 to 10) mV (10 to 20) mV (1 to 5) mV (5 to 50) mV (50 to 500) mV

1.6 nA 2.3 nA 2.7 nA 14 nA 22 nA 26 nA 0.14 μA 0.22 μA 0.26 μA 1.4 μA 2.2 μA 2.7 μA 15 μA 23 μA 28 μA 0.16 mA 0.27 mA 0.34 mA 2.1 mA 3.7 mA 4.5 mA 41 mA 61 mA 0.11 A 0.22 A 88 μV 0.10 mV 0.19 mV 0.96 mV 1.1 μV 5.8 μV 58 μV

Fluke 8508A current shunts Tektronix TDS784D HP 6051A Kikusui PCR-500L Tektronix TDS784D HP 6051A Kikusui PCR-500L

DC Voltage Standards –

DC Voltage

1.018 V 10 V

4.8 × 10-7 2.4 × 10-6

Fluke 732B Fluke 8508A


Parameter/Equipment


DC Voltmeters –

DC Voltage DC Voltage

0 V (0 to 4) mV (4 to 8) mV (8 to 10) mV (10 to 40) mV (40 to 80) mV (80 to 100) mV (100 to 400) mV (400 to 800) mV (0.8 to 1) V (1 to 4) V (4 to 8) V (8 to 10) V (10 to 40) V (40 to 80) V (80 to 100) V (100 to 400) V (400 to 800) V (400 to 1000) V (0 to -4) mV (-4 to -8) mV (-8 to -10) mV (-10 to -40) mV (-40 to -80) mV (-80 to -100) mV (-100 to -400) mV (-400 to -800) mV (-0.8 to -1) V (-1 to -4) V (-4 to -8) V (-8 to -10) V (-10 to -40) V (-40 to -80) V (-80 to -100) V (-100 to -400) V (-400 to -800) V (-800 to -1000) V

0.78 μV 0.81 μV 0.84 μV 0.85 μV 1.0 μV 1.3 μV 1.5 μV 6.9 μV 8.2 μV 9.0 μV 64 μV 71 μV 75 μV 0.67 mV 0.80 mV 0.88 mV 8.0 mV 9.0 mV 11 mV 0.81 μV 0.84 μV 0.85 μV 1.0 μV 1.3 μV 1.5 μV 6.9 μV 8.2 μV 9.0 μV 64 μV 71 μV 75 μV 0.67 mV 0.80 mV 0.88 mV 8.0 mV 9.0 mV 11 mV

Fluke 5730A


Parameter/Equipment


Static/Ionic Voltmeters –

Static Voltage (Positive)

Static Voltage (Negative)

(0 to 100) V (100 to 500) V (0.5 to 1) kV (1 to 10) kV (10 to 15) kV (15 to 20) kV (20 to 25) kV (25 to 30) kV (30 to 35) kV (35 to 40) kV (40 to 45) kV (45 to 48) kV (0 to -100) V (-100 to -500) V (-0.5 to -1) kV (-1 to -10) kV (-10 to -15) kV (-15 to -20) kV (-20 to -25) kV (-25 to -30) kV (-30 to -35) kV (-35 to -40) kV (-40 to -45) kV (-45 to -48) kV

6.2 × 10-4 1.2 × 10-4 6.2 × 10-4 6.1 × 10-3 4.7 × 10-3 3.6 × 10-3 2.8 × 10-3 2.4 × 10-3 2.0 × 10-3 1.8 × 10-3 1.6 × 10-3 1.5 × 10-3 6.2 × 10-4 1.2 × 10-4 6.2 × 10-4 6.1 × 10-3 4.7 × 10-3 3.6 × 10-3 2.8 × 10-3 2.4 × 10-3 2.0 × 10-3 1.8 × 10-3 1.6 × 10-3 1.5 × 10-3

Fluke 5730A Bertan 210-30R Matsusada AU-50R12


Parameter/Range

Frequency CMC2, 3, 5 (±) Comments

Capacitance Bridges / Indicators –

Frequency

AC Voltage (1 to 100) mV

(0.1 to 1) V

(10 to 20) V

Capacitance 1 pF (1 to 10) pF

(10 to 100) pF

10 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz (0.1 to 1) MHz (1 to 10) MHz (10 to 30) MHz 20 Hz (0.02 to 1) kHz (1 to 10) kHz (10 to 100) kHz 100 kHz to 1 MHz 20 Hz (0.02 to 10) kHz (10 to 100) kHz (0.1 to 1) MHz 20 Hz (0.02 to 1) kHz (1 to 10) kHz (10 to 100) kHz 1 kHz to 1 MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz 1 KHz to 5 MHz (5 to 10) MHz (10 to 13) MHz 1 KHz to 4 MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz

5.8 × 10-6 5.8 × 10-7 5.9 × 10-8 8.2 × 10-9 5.9 × 10-8 2.0 × 10-8

2.0 × 10-4 1.8 × 10-4 2.2 × 10-4 1.1 × 10-3 2.5 × 10-1 6.4 × 10-4 5.9 × 10-4 1.0 × 10-3 3.5 × 10-2 8.8 × 10-4 3.4 × 10-4 3.8 × 10-4 1.8 × 10-3 0.76 fF 0.78 fF 0.86 fF 0.98 fF 1.2 fF 2.6 fF 3.8 fF 3.6 fF 3.8 fF 3.9 fF 36 fF 38 fF 49 fF 61 fF

HP 53131A HP 1638XX capacitance set, IET SCA-XX capacitance


Parameter/Range

Frequency CMC2, 3 (±) Comments

Capacitance Bridges / Indicators – (cont)

Capacitance (100 to 1000) pF

(1 to 10) nF (10 to 100) nF (0.1 to 1) μF

(1 to 10) μF (10 to 100) μF (0.1 to 1) mF

1 KHz to 1 MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz 120 Hz to 100 kHz 120 Hz to 100 kHz 120 Hz to 10 kHz 10 kHz to 100 kHz 100 Hz to 1 kHz 100 Hz (0.1 to 1) kHz 100 Hz (0.1 to 1) kHz

0.36 pF 0.38 pF 0.45 pF 0.57 pF 0.72 pF 2.0 pF 3.0 pF 0.82 pF 8.2 pF 0.11 nF 0.13 nF 3.2 nF 71 nF 77 nF 1.5 μF 4.2 μF

HP 1638XX capacitance set, IET SCA-XX capacitance


Parameter/Frequency


Decade Capacitors –

1 kHz 120 Hz

(1 to 10) pF 10 pF to 1 nF (1 to 100) nF (0.1 to 1) μF (1 to 10) μF (10 to 100) μF (0.1 to 1) mF

9.4 × 10-6 6.2 × 10-6 5.1 × 10-5 9.1 × 10-5 1.2 × 10-3 1.2 × 10-3 1.3 × 10-3

AH 2700A HP 4284A

Standard Capacitors –

1 kHz 120 Hz

1 pF 10 pF 100 pF 1 nF 10 nF 100 nF 1 μF 10 μF 100 μF 1 mF

7.3 aF 72 aF 0.63 fF 6.2 fF 0.51 pF 5.1 pF 91 pF 12 nF 0.12 μF 1.3 μF

AH 2700A HP 4284A

Earth Testers –

Earth Tester

Voltage DC 1 kHz

Current DC 1 kHz

100 mΩ 100 mΩ to 1 Ω (1 to 10) Ω (10 to 100) Ω 100 Ω to 1 kΩ (1 to 2) kΩ (1 to 100) V (100 to 600) V 1 A (1 to 10) A (10 to 60) A

5.8 × 10-3 6.2 × 10-4 1.2 × 10-4 6.6 × 10-5 6.4 × 10-5 3.0 × 10-4 5.9 × 10-4 1.4 × 10-4 1.4 × 10-3 1.3 × 10-3 1.3 × 10-3

Iet HARS-X-10-.001 Fluke 5730A Fluke 8508A Ballantine 1625A

Inductors –

(1 kHz)

(0.1 to 1) mH 1 mH to 1 H

1.2 × 10-3 6.3 × 10-4

HP 4284A


Parameter/Frequency


Insulation Testers –

Resistance

Insulation Voltage

Voltage: DC 1 kHz

Resistance

1 kΩ 1 kΩ to 1 MΩ (1 to 10) MΩ (10 to 100) MΩ 100 MΩ to 1 GΩ (1 to 10) GΩ (10 to 100) GΩ 100 GΩ to 1 TΩ 25 V (25 to 800) V 800 V to 9 kV 10 V (10 to 600) V 10 Ω (10 to 100) Ω 100 Ω to 100 kΩ

6.2 × 10-4 6.7 × 10-5 9.0 × 10-5 1.7 × 10-4 5.4 × 10-4 8.5 × 10-4 2.7 × 10-3 7.0 × 10-3 2.3 × 10-4 7.3 × 10-5 6.2 × 10-3 5.9 × 10-4 1.3 × 10-4 5.9 × 10-4 6.6 × 10-5 6.4 × 10-5

IET HARS-X-10-.001, IET HRRS-B-8-100k-5kV Fluke 8508A Kikusui 149-10A Fluke 5730A IET HARS-X-10-.001

Q-Meter –

AC Voltage

Frequency

10 mV 100 mV 1 V 10 V DC 1 kHz (1 to 10) kHz (10 to 100) kHz 100 kHz to 1 MHz (1 to 10) MHz (10 to 100) MHz

58 μV 0.58 mV 0.59 mV 5.9 mV 5.8 × 10-6 5.8 × 10-7 5.9 × 10-8 9.0 × 10-9 5.9 × 10-8

8.2 × 10-8

Fluke 8508A HP 53131A


Parameter/Equipment


Resistance Bridges and Similar Instruments –

Measuring Arm

Ratio Arm

0.01 Ω (0.01 to 0.1) Ω (0.1 to 1) Ω (1 to 10) Ω (10 to 100) Ω 100 Ω to 1 kΩ (1 to 10) kΩ (10 to 100) kΩ 100 kΩ to 1 MΩ (1 to 10) MΩ (10 to 100) MΩ × 0.001 × 0.01 × 0.1 × 1 × 10 × 100 × 1000

7.5 μΩ 8.5 μΩ 18 μΩ 0.11 mΩ 0.90 mΩ 9.0 mΩ 90 mΩ 0.92 Ω 11 Ω 0.26 kΩ 16 kΩ 5.8 × 10-8 5.8 × 10-7 5.8 × 10-6 5.8 × 10-5 5.9 × 10-4 5.9 × 10-3 6.0 × 10-2

Fluke 8508A . Guildline 9330-X resistance, Fluke 742A-X resistance

Resistance Meters –

DC Resistance

Frequency

1 mΩ 10 mΩ 100 mΩ 1 Ω (1 to 10) Ω (10 to 100) Ω (0.1 to 100) kΩ 100 kΩ to 1 MΩ (1 to 10) MΩ (10 to 100) MΩ (0.1 to 1) GΩ (1 to 10) GΩ (10 to 100) GΩ (0.1 to 1) TΩ (1 to 10) TΩ 10 Hz (10 to 100) Hz 100 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz 100 kHz to 1 MHz

0.25 μΩ 1.2 μΩ 0.69 μΩ 3.3 μΩ 2.2 × 10-4 9.6 × 10-5 3.9 × 10-5 3.7 × 10-5 8.7 × 10-5 2.2 × 10-4 1.4 × 10-3 4.1 × 10-3 6.5 × 10-3 2.2 × 10-2 6.6 × 10-2

5.8 mHz 5.8 × 10-5 5.8 × 10-6 5.8 × 10-7 5.9 × 10-8 8.2 × 10-9

Yokogawa 2792-X, Guildline 9330-0.1 Ω, Tinsley 5685A, IET HARS-X-10-.001, IET HRRS-B-8-100k-5kV HP 53131A


Parameter/Frequency


Resistance Meters – (cont)

AC Voltage @1 kHz

AC Resistance @ 1 kHz

DC Voltage

10 mV (10 to 100) mV 100 mV to 1 V (1 to 10) V (10 to 100) V (100 to 1000) V 1 Ω 10 Ω 100 Ω 1 kΩ 10 kΩ 100 kΩ 100 mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V

6.8 µV 1.9 × 10-4 1.1 × 10-4 1.3 × 10-4 1.3 × 10-4 1.5 × 10-4 1.2 mΩ 3.7 mΩ 36 mΩ 0.36 Ω 3.6 Ω 36 Ω 0.75 μV 7.1 × 10-6 7.1 × 10-6 7.9 × 10-6 8.1 × 10-6

Fluke 8508A HP 16074A resistance set Fluke 8508A

Resistors –

Standard Resistance (DC)

1 Ω 10 Ω 25 Ω 100 Ω 1 kΩ 10 kΩ 100 kΩ 1 MΩ 10 MΩ 100 MΩ 1 GΩ 10 GΩ

4.9 µΩ 0.18 mΩ 0.13 mΩ 0.59 mΩ 5.3 mΩ 27 mΩ 0.80 Ω 12 Ω 0.22 kΩ 3.1 kΩ 49 kΩ 3.5 MΩ

Standard resistances Fluke 8508A


Parameter/Frequency


Resistors – (cont)

Standard Resistance (AC) 1 kHz (1 to 100) kHz (0.1 to 1) MHz

Decade Resistance (DC)

1 kHz

1 Ω 10 Ω 100 Ω 1 kΩ 10 kΩ 100 kΩ 1 kΩ 10 kΩ 100 kΩ 10 Ω 100 Ω 1 kΩ 10 kΩ 100 kΩ (1 to 10) mΩ (10 to 100) mΩ 100 mΩ to 1 Ω (1 to 10) Ω (10 to 100) Ω 100 Ω to 1 kΩ (1 to 10) kΩ (10 to 100) kΩ 100 kΩ to 1 MΩ (1 to 10) MΩ (10 to100) MΩ 100 MΩ to 1 GΩ (1 to 10) GΩ (10 to 100) GΩ 100 GΩ to 1 TΩ 100 mΩ to 10 Ω 10 Ω to 100 kΩ

1.2 mΩ 3.8 mΩ 36 mΩ 0.36 Ω 3.6 Ω 36 Ω 12 Ω 0.12 kΩ 1.2 kΩ 0.12 Ω 1.2 Ω 12 Ω 0.12 kΩ 1.2 kΩ 7.3 × 10-4 9.5 × 10-5 8.7 × 10-5 4.9 × 10-5 9.1 × 10-6 9.6 × 10-6 9.1 × 10-6 9.2 × 10-6 1.1 × 10-5 1.7 × 10-5 4.9 × 10-5 2.0 × 10-4 7.1 × 10-4 3.1 × 10-3 4.4 × 10-3 1.2 × 10-3 6.5 × 10-4

Keysight 42030A, HP 46074A Fluke 8508A HP 4284A

Electrical Conductivity Meters

14.36 MS/m 22.90 MS/m 34.28 MS/m 58.38 MS/m

0.076 MS/m 0.16 MS/m 0.20 MS/m 0.33 MS/m

Fischer 14.36 MS/m Fischer 22.90 MS/m Fischer 34.28 MS/m Fischer 58.38 MS/m


Parameter/Range


Impedance Bridges/LCR Meters –

Frequency

AC Voltage 100 mV

(0.1 to 1) V (1 to 10) V (10 to 20) V

DC Voltage DC Current

10 Hz 10 Hz to 100 Hz 100 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz (0.1 to 1) MHz (1 to 10) MHz (10 to 30) MHz 20 Hz 20 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz (0.1 to 1) MHz 20 Hz 20 Hz to 10 kHz (10 to 100) kHz (0.1 to 1) MHz 20 Hz 20 Hz to 10 kHz (10 to 100) kHz (0.1 to 1) MHz 20 Hz 20 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz 100 mV (0.1 to 10) V (10 to 40) V 1 A (1 to 10) A (10 to 20) A (20 to 40) A

5.8 mHz 5.8 × 10-5 5.8 × 10-6 5.8 × 10-7 5.9 × 10-8 8.2 × 10-9 5.9 × 10-8 2.0 × 10-8 21 μV 1.9 × 10-4 2.3 × 10-4 1.1 × 10-3 2.5 × 10-1 6.4 × 10-4 5.9 × 10-4 1.0 × 10-3 3.5 × 10-2 6.4 × 10-4 6.0 × 10-4 1.0 × 10-3 3.5 × 10-2 9.9 × 10-4 3.4 × 10-4 4.4 × 10-4 1.8 × 10-3 1.1 µV 5.9 × 10-3 2.2 × 10-5 0.62 mA 4.7 × 10-4 8.5 × 10-4 8.5 × 10-4

HP 53131A Fluke 8508A Fluke 8508A Fluke 8508A, Ballantine 1625A


Parameter/Range


Impedance Bridges/LCR Meters – (cont)

Resistance 1 Ω

(1 to 10) Ω (10 to 100) Ω 100 Ω to 1 kΩ (1 to 10) kΩ (10 to 100) kΩ

Capacitance

1 pF (1 to 10) pF (10 to 100) pF (100 to 1000) pF

1 kHz 1 kHz 1 kHz to 5 MHz (5 to 10) MHz (10 to 13) MHz 1 kHz 1 kHz to 13 MHz 1 kHz 1 kHz to 13 MHz 1 kHz 1 kHz to 1 MHz 1 kHz 1 kHz to 1 MHz 1 kHz to 1 MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz 1 kHz to 5 MHz (5 to 10) MHz (10 to 13) MHz 1 kHz to 4 MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz 1 kHz to 1 MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz

1.2 mΩ 3.6 mΩ 0.12 Ω 0.13 Ω 0.14 Ω 36 mΩ 1.2 Ω 0.36 Ω 12 Ω 3.6 Ω 0.12 kΩ 36 Ω 1.2 kΩ 0.76 fF 0.78 fF 0.86 fF 0.98 fF 1.2 fF 2.6 fF 3.8 fF 3.6 fF 3.8 fF 3.9 fF 36 fF 38 fF 49 fF 61 fF 0.36 pF 0.38 pF 0.45 pF 0.57 pF 0.72 pF 2.0 pF 3.0 pF

HP 16074A HP 1638XX capacitance set


Parameter/Range


Impedance Bridges/LCR Meters – (cont)

Capacitance (cont) (1 to 10) nF (10 to 100) nF (0.1 to 1) μF (1 to 10) μF (10 to 100) μF (0.1 to 1) mF

Inductance

100 μH (0.1 to 1) mH (1 to 10) mH (10 to 100) mH (0.1 to 1) H

120 Hz to 100 kHz 120 Hz to 100 kHz 120 Hz to 10 kHz (10 to 100) kHz 100 Hz to 1 kHz 100 Hz 100 Hz to 1 kHz 100 Hz 100 Hz to 1 kHz 1 kHz

0.82 pF 8.2 pF 0.11 nF 0.13 nF 3.2 nF 71 nF 77 nF 1.5 μF 4.2 μF 21 nH 0.15 μH 1.4 μH 15 μH 0.15 mH

HP 1638XX capacitance set Gen-rad 1482X inductance set

AC Ammeters –

AC Current 10 μA 10 μA to 10 mA (10 to 100) mA 100 mA to 1 A

(50 to 60) Hz 60 Hz to 1 kHz 40 Hz 40 Hz to 1 kHz (1 to 10) kHz 40 Hz 40 Hz to 1 kHz (1 to 10) kHz 40 Hz to 1 kHz (1 to 10) kHz

2.0 × 10-3 9.0 × 10-3 3.0 × 10-4 2.0 × 10-4 2.1 × 10-3 3.0 × 10-4 2.0 × 10-4 2.0 × 10-3 4.0 × 10-4 8.4 × 10-3

Fluke 5730A and 52120A


Parameter/Range


AC Ammeters – (cont)

AC Current (1 to 10) A (10 to 20) A (20 to 50) A (50 to 100) A (0 to 10) V (1 to 10) V (10 to 75) (75 to 150) V (150 to 300) V

(300 to 750) V

(50 to 60) Hz 60 Hz to 1 kHz (50 to 60) Hz 60 Hz to 1 kHz (50 to 60) Hz (50 to 60) Hz 40 Hz 40 Hz to 10 kHz 40 Hz 40 Hz to 10 kHz 40 Hz 40 Hz to 10 kHz 40 Hz to 1 kHz 50 Hz 50 Hz to 1 kHz 50 Hz 50 Hz to 1 kHz

1.3 × 10-3 2.0 × 10-3 7.0 × 10-4 1.5 × 10-3 6.0 × 10-4 4.0 × 10-4 1.8 × 10-2 1.0 × 10-2 2.0 × 10-4 1.0 × 10-4 2.7 × 10-4 1.3 × 10-4 1.3 × 10-4 6.7 × 10-4 3.3 × 10-4 4.0 × 10-4 1.3 × 10-4

Fluke 5730A and 52120A

Clamp Ammeters/Voltmeters –

DC Voltage

AC Voltage (0 to 100) mV 100 mV to 1 V

(0 to 100) mV 100 mV to 100 V (100 to 1000) V 40 Hz 40 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 40 Hz 40 Hz to 20 kHz (20 to 100) kHz

6.3 × 10-5 6.1 × 10-5 6.2 × 10-5 1.3 × 10-4 9.8 × 10-5 1.6 × 10-4 3.8 × 10-4 1.4 × 10-4 8.5 × 10-5 1.5 × 10-4

Fluke 5730A


Parameter/Range


Clamp Ammeters/Voltmeters – (cont)

AC Voltage

(1 to 10) V

(10 to 100) V (100 to 1000) V

DC Current

AC Current (0 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 10) A (10 to 100) A (100 to 200) A (200 to 300) A

40 Hz to 10 kHz (10 to 20) kHz (20 to 50) kHz (50 to 100) kHz 40 Hz to 10 kHz (10 to 20) kHz (20 to 50) kHz (50 to 100) kHz 50 Hz 50 Hz to 1 kHz 0 mA to 1 A (1 to 10) A (10 to 50) A (50 to 100) A (100 to 200) A (200 to 300) A (300 to 400) A (400 to 500) A (500 to 750) A (750 to 1000) A (1000 to 1500) A (1500 to 2000) A (2000 to 2500) A 40 Hz to 1 kHz (1 to 10) kHz 40 Hz to 1 kHz (1 to 10) kHz 40 Hz to 1 kHz (1 to 10) kHz 40 Hz to 60 Hz 60 Hz to 1 kHz 60 Hz 60 Hz 60 Hz

1.4 × 10-4 8.4 × 10-5 1.1 × 10-4 1.4 × 10-4

1.4 × 10-4 9.4 × 10-5 1.2 × 10-4 2.2 × 10-4 3.7 × 10-4 1.1 × 10-4 6.1 × 10-4 6.5 × 10-4 1.2 × 10-3 6.3 × 10-4 1.2 × 10-3 8.9 × 10-4 7.5 × 10-4 6.6 × 10-4 1.6 × 10-3 1.3 × 10-3 9.5 × 10-4 7.9 × 10-4 6.9 × 10-4 6.2 × 10-4 1.0 × 10-3 6.5 × 10-4 2.6 × 10-3 6.2 × 10-4 1.2 × 10-3 1.4 × 10-3 2.1 × 10-3 7.1 × 10-4 1.2 × 10-3 8.9 × 10-4

Fluke 5730A Fluke 5730A and 52120A current coil

Fluke 5730A and 52120A current coil


Parameter/Range


Clamp Ammeters/Voltmeters (cont)

AC Current

(300 to 500) A (500 to 900) A (900 to 1000) A (1000 to 1500) A (1500 to 2000) A (2000 to 2500) A (2500 to 3000) A

Resistance

Current Coil (AC Ratio)

Current Coil (DC Ratio)

60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz (0 to 1) Ω (1 to 10) Ω (10 to 100) Ω 100 Ω to 1 kΩ (1 to 100) kΩ 100 kΩ to 1 MΩ (1 to 10) MΩ (10 to 100) MΩ 2 10 25 50 2 10 25 50

6.6 × 10-4 1.6 × 10-3 1.4 × 10-3 1.2 × 10-3 1.0 × 10-3 8.5 × 10-4 7.6 × 10-4 8.6 × 10-4 1.1 × 10-4 6.3 × 10-5 6.8 × 10-5 6.6 × 10-5 6.2 × 10-5 1.3 × 10-4 1.4 × 10-4 0.15 % 0.13 % 0.17 % 0.14 % 0.14 % 0.07 % 0.13 % 0.08 %

ESI RS925D, IET HRRS-B-4-10B-5kV Fluke 5730A and 52120A Fluke 8508A Fluke 335 Fluke A40B-100A Fluke 5730A and 52120A Fluke 8508A Fluke 335 Fluke A40B-100A


Parameter/Range


AC Voltage/Current Calibrators – AC Voltage

0.1 V (0.1 to 0.4) V (0.4 to 0.8) V (0.8 to 1) V (1 to 4) V (4 to 8) V (8 to 10) V

50 Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 30) kHz (30 to 100) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 30) kHz (30 to 100) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 30) kHz (30 to 100) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 30) kHz (30 to 100) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 30) kHz (30 to 100) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 30) kHz (30 to 100) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 30) kHz (30 to 100) kHz

18 μV 1.6 × 10-4 1.8 × 10-4 4.6 × 10-4 1.1 × 10-3 0.08 mV 1.8 × 10-4 2.0 × 10-4 4.0 × 10-4 1.2 × 10-3 0.11 mV 1.3 × 10-4 1.4 × 10-4 3.1 × 10-4 8.8 × 10-4 0.13 mV 1.1 × 10-4 1.3 × 10-4 2.9 × 10-4 8.2 × 10-4 0.8 mV 1.8 × 10-4 2.0 × 10-4 4.0 × 10-4 1.2 × 10-3 1.1 mV 1.3 × 10-4 1.4 × 10-4 3.1 × 10-4 8.8 × 10-4 1.3 mV 1.1 × 10-4 1.3 × 10-4 2.9 × 10-4 8.2 × 10-4

Fluke 8508A


Parameter/Range


AC Voltage/Current Calibrators – AC Voltage (cont)

(10 to 40) V (40 to 80) V (80 to 100) V (100 to 400) V (400 to 800) V (800 to 1000) V

50 Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 30) kHz (30 to 100) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 30) kHz (30 to 100) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 30) kHz (30 to 100) kHz 50 Hz (50 to 300) Hz 300 Hz to 1 kHz (1 to 10) kHz 50 Hz (50 to 300) Hz 300 Hz to 1 kHz (1 to 10) kHz 50 Hz (50 to 300) Hz 300 Hz to 1 kHz (1 to 10) kHz

8.1 mV 1.9 × 10-4 2.0 × 10-4 4.3 × 10-4 1.2 × 10-3 12 mV 1.3 × 10-4 1.5 × 10-4 3.1 × 10-4 8.8 × 10-4 13 mV 1.1 × 10-4 1.3 × 10-4 3.0 × 10-4 8.2 × 10-4 0.13 V 3.3 × 10-4 2.3 × 10-4 3.3 × 10-4 0.15 V 1.9 × 10-4 1.5 × 10-4 1.9 × 10-4 0.16 V 1.6 × 10-4 1.4 × 10-4 1.6 × 10-4

Fluke 8508A


Parameter/Range


AC Voltage/Current Calibrators – AC Current

100 μA (0.1 to 0.4) mA (0.4 to 0.8) mA (0.8 to 1) mA (1 to 4) mA (4 to 8) mA (8 to 10) mA (10 to 40) mA (40 to 80) mA (80 to 100) mA

50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz

71 nA 7.0 × 10-4 7.1 × 10-4 0.01 μA 2.3 × 10-4 2.5 × 10-4 0.14 μA 1.5 × 10-4 1.8 × 10-4 0.16 μA 1.4 × 10-4 1.7 × 10-4 0.90 μA 2.1 × 10-4 2.3 × 10-4 1.3 μA 1.4 × 10-4 1.6 × 10-4 1.4 μA 1.2 × 10-4 1.4 × 10-4 8.9 μA 2.1 × 10-4 2.2 × 10-4 12 μA 1.3 × 10-4 1.5 × 10-4 14 μA 1.2 × 10-4 1.4 × 10-4

Fluke 8508A and Fluke A40B current shunt


Parameter/Range


AC Voltage/Current Calibrators – AC Current (cont)

(0.1 to 0.4) A (0.4 to 0.8) A (0.8 to 1) A (1 to 4) A (4 to 8) A (8 to 10) A (10 to 30) A (30 to 50) A (50 to 80) A (80 to 100) A

50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 1 kHz 50 Hz 50 Hz to 1 kHz 50 Hz 50 Hz to 1 kHz 50 Hz 50 Hz to 1 kHz

90 μA 2.1 × 10-4 2.3 × 10-4 0.12 mA 1.4 × 10-4 1.5 × 10-4 0.14 mA 1.2 × 10-4 1.4 × 10-4 0.91 mA 2.1 × 10-4 2.3 × 10-4 1.3 mA 1.4 × 10-4 1.8 × 10-4 1.5 mA 1.3 × 10-4 1.6 × 10-4 5.7 mA 1.7 × 10-4 7.8 mA 1.4 × 10-4 14 mA 1.6 × 10-4 16 mA 1.5 × 10-4

Fluke 8508A and Fluke A40B current shunt


Parameter/Frequency


AC Voltage/Current Calibrators – Clamp Meter

60 Hz

1 A (1 to 3) A (3 to 8) A (8 to 10) A (10 to 20) A (20 to 30) A (30 to 50) A (50 to 80) A (80 to 100) A (100 to 200) A (200 to 300) A (300 to 500) A (500 to 800) A (800 to 1000) A

0.20 A 0.23 A 0.32 A 0.35 A 0.53 A 0.71 A 1.5 A 2.0 A 2.4 A 4.2 A 11 A 15 A 20 A 24 A

Fluke 355

Wattmeter Calibrators –

Active Power

(50 to 60) Hz

Power Factor

(50 to 60) Hz

Harmonic (THD-V or THD-I) (50 to 60) Hz

Frequency

0.12 W (0.12 to 0.24) W (0.24 to 0.6) W (0.6 to 1.2) W (1.2 to 6) W (6 to 12) W (12 to 600) W 600 W to 4.8 kW (-1 to 1) 0.5 % (0.5 to 1) % (1 to 3) % (3 to 5) % (5 to 10) % (10 to 20) % 20 Hz (20 to 60) Hz (60 to 100) Hz (100 to 400) Hz (0.4 to 1) kHz

0.09 mW 4.6 × 10-4 3.7 × 10-4 3.1 × 10-4 3.2 × 10-4 3.1 × 10-4 3.2 × 10-4 3.1 × 10-4 3.2 × 10-4 lin 1.2 × 10-1 6.1 × 10-2 2.0 × 10-2 1.2 × 10-2 6.1 × 10-3 3.1 × 10-3 3.5 × 10-4 1.2 × 10-4 1.4 × 10-4 1.2 × 10-4 6.5 × 10-2

Zimmer LMG670 Zimmer LMG670 Zimmer LMG670 HP 34401A


Parameter/Frequency


AC Current Shunts –

AC Resistance

(40 to 60) Hz (60 to 100) Hz (100 to 1) kHz

0.001 Ω (0.001 to 0.01) Ω (0.01 to 0.1) Ω (0.1 to 1) Ω (1 to 10) Ω (10 to 100) Ω (100 to 1000) Ω 0.001 Ω (0.001 to 0.01) Ω (0.01 to 0.1) Ω (0.1 to 1) Ω (1 to 10) Ω (10 to 100) Ω (100 to 1000) Ω 0.001 Ω (0.001 to 0.01) Ω (0.01 to 0.1) Ω (0.1 to 1) Ω (1 to 10) Ω (10 to 100) Ω (100 to 1000) Ω

0.61 μΩ 20 μΩ 38 μΩ 0.25 mΩ 2.9 mΩ 29 mΩ 0.35 Ω 0.61 μΩ 20 μΩ 37 μΩ 0.19 mΩ 2.2 mΩ 22 mΩ 0.26 Ω 2.0 μΩ 20 μΩ 37 μΩ 0.19 mΩ 2.2 mΩ 22 mΩ 0.26 Ω

Fluke 8508A, Fluke 5730A and 52120A

Power Factor Meters – (50 to 60 Hz)

-1 to 1

0.0015 lin

Fluke 6100A

AC Power Meters –

AC Power 50 Hz

0.12 W (0.12 to 0.24) W (0.24 to 0.6) W (0.6 to 1.2) W (1.2 to 2.4) W (2.4 to 6) W (6 to 600) W 600 W to 1.2 kW (1.2 to 2.4) kW (2.4 to 12) kW (12 to 50) kW

0.13 mW 0.14 mW 0.28 mW 0.43 mW 0.76 mW 3.2 × 10-4 3.1 × 10-4 3.3 × 10-4 3.7 × 10-4 5.2 × 10-4 6.0 × 10-4

Fluke 6105A


Parameter/Frequency


AC Power Meters – (cont)

AC Power 60 Hz

DC Power

Power Factor (50 to 60) Hz

0.12 W (0.12 to 0.24) W (0.24 to 0.6) W (0.6 to 1.2) W (1.2 to 2.4) W (2.4 to 6) W (6 to 600) W 600 W to 1.2 kW (1.2 to 2.4) kW (2.4 to 12) kW (12 to 50) kW 0.12 W (0.12 to 0.24) W (0.24 to 0.6) W (0.6 to 1.2) W (1.2 to 2.4) W (2.4 to 4.8) W (4.8 to 6) W (6 to 12) W (12 to 24) W (24 to 60) W (60 to 120) W (120 to 240) W (240 to 480) W (480 to 600) W (0.6 to 1.2) kW (1.2 to 2.4) kW (2.4 to 4.8) kW (4.8 to 20) kW -1 to 1

0.18 mW 0.19 mW 0.41 mW 0.51 mW 0.87 mW 1.9 mW 3.1 × 10-4 3.3 × 10-4 3.7 × 10-4 5.2 × 10-4 6.0 × 10-4 23 μW 43 μW 0.11 mW 0.22 mW 0.36 mW 0.81 mW 1.1 mW 1.9 mW 3.6 mW 20 mW 33 mW 0.12 W 0.23 W 0.42 W 0.77 W 2.9 W 5.8 W 63 W 1.3 × 10-4 lin

Fluke 6105A Fluke 5522A Fluke 6105A


Parameter/Frequency



AC Voltage

(50 to 60) Hz AC Current

(50 to 60) Hz DC Voltage

1 V (1 to 2) V (2 to 5) V (5 to 10) V (10 to 20) V (20 to 50) V (50 to 60) V (60 to 100) V (100 to 150) V (150 to 200) V (200 to 300) V (300 to 500) V (500 to 600) V (600 to 750) V (750 to 1000) V 1 mA (1 to 10) mA (10 to 20) mA (20 to 50) mA (50 to 100) mA (100 to 200) mA (200 to 500) mA (0.5 to 1) A (1 to 2) A (2 to 5) A (5 to 10) A (10 to 20) A (20 to 30) A (30 to 50) A 1 V (1 to 2) V (2 to 5) V (5 to 20) V (20 to 50) V (50 to 60) V (60 to 200) V (200 to 300) V (300 to 500) V (500 to 600) V (600 to 750) V (750 to 1000) V

85 μV 0.13 mV 0.37 mV 0.85 mV 1.3 mV 4.5 mV 5.0 mV 9.4 mV 12 mV 15 mV 32 mV 47 mV 59 mV 70 mV 0.11 V 0.18 μA 1.8 μA 2.9 μA 8.5 μA 17 μA 28 μA 0.21 mA 0.34 mA 0.62 mA 3.0 mA 5.6 mA 14 mA 27 mA 30 mA 61 μV 62 μV 66 μV 0.62 mV 0.70 mV 0.73 mV 6.2 mV 6.8 mV 7.5 mV 7.9 mV 8.7 mV 62 mV

Fluke 5522A Fluke 5730A and 52120A Fluke 5522A


Parameter/Frequency



DC Current

Harmonic Voltage

Harmonic Current

Frequency

Flicker Pst

(1 to 4000) cpm

Pinst.Max (Sinusoidal) (0.5 to 8.8) Hz (8.8 to 20) Hz (20 to 25) Hz (25 to 33.333) Hz

Pinst Max (Square)

(0 to 28) Hz (28 to 30.5) Hz (30.5 to 33.333) Hz

Pst Range

1 mA (1 to 10) mA (10 to 20) mA (20 to 50) mA (50 to 100) mA (100 to 200) mA (200 to 500) mA 500 mA to 1 A (1 to 2) A (2 to 5) A (5 to 10) A (10 to 20) A (20 to 30) A (30 to 50) A (50 to 60) Hz (0.5 to 20) % (50 to 60) Hz (0.5 % to 20 %) 20 Hz (20 to 50) Hz (50 to 60) Hz (60 to 200) Hz (200 to 400) Hz (400 to 600) Hz (600 to 800) Hz 800 Hz to 1 kHz 1 1 1 1 1 1 1 1 0.25 0.25 to 5

80 nA 1.1 μA 1.7 μA 5.3 μA 11 μA 19 μA 91 μA 0.16 mA 0.26 mA 1.6 mA 2.1 mA 3.2 mA 8.6 mA 10 mA 0.053 % 0.053 % 0.59 mHz 1.2 × 10-5 1.0 × 10-5 5.8 × 10-5 2.9 × 10-5 1.9 × 10-5 1.5 × 10-5 5.9 × 10-5 0.39 % 0.38 % 0.40 % 0.41 % 0.43 % 0.40 % 1.1 % 0.40 % 0.39 % 0.42 %

Fluke 5730A and 52120A Fluke 6100A Fluke 6100A Fluke 5522A Fluke 6105A, N4L PPA5511


Parameter/Range


AC power Supplies –

AC Voltage

100 mV (0.1 to 0.4) V (0.4 to 0.8) V (0.8 to 1) V (1 to 4) V (4 to 8) V

(8 to 10) V

20 Hz (20 to 50) Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz 20 Hz (20 to 50) Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz 20 Hz (20 to 50) Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz 20 Hz (20 to 50) Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz 20 Hz (20 to 50) Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz 20 Hz (20 to 50) Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz 20 Hz (20 to 50) Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz

21 μV 1.9 × 10-4 1.7 × 10-4 1.9 × 10-4 1.1 × 10-3 0.11 mV 2.8 × 10-4 2.5 × 10-4 2.8 × 10-4 1.2 × 10-3 0.15 mV 1.6 × 10-4 1.5 × 10-4 1.6 × 10-4 8.9 × 10-4 0.17 mV 1.5 × 10-4 1.3 × 10-4 1.5 × 10-4 8.2 × 10-4 1.2 mV 2.8 × 10-4 2.6 × 10-4 2.8 × 10-4 1.2 × 10-3 1.5 mV 1.6 × 10-4 1.5 × 10-4 1.6 × 10-4 8.9 × 10-4 1.7 mV 1.5 × 10-4 1.3 × 10-4 1.5 × 10-4 8.2 × 10-4

Fluke 8508A and Vitrek 4700


Parameter/Range



AC Voltage (cont) (10 to 50) V

(50 to 80) V (80 to 100) V (100 to 150) V (150 to 200) V (200 to 300) V

(300 to 500) V (500 to 800) V (800 to 1000) V (1 to 1.5) kV

20 Hz (20 to 50) Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz 20 Hz 20 Hz to 50 Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz 20 Hz (20 to 50) Hz 50 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz 50 Hz (50 to 100) Hz 100 Hz to 1 kHz (1 to 10) kHz 50 Hz (50 to 100) Hz 100 Hz to 1 kHz (1 to 10) kHz 50 Hz (50 to 100) Hz 100 Hz to 1 kHz (1 to 10) kHz 50 Hz 50 Hz to 10 kHz 50 Hz 50 Hz to 10 kHz 50 Hz 50 Hz to 10 kHz 60 Hz

15 mV 2.4 × 10-4 2.2 × 10-4 2.4 × 10-4 1.1 × 10-3 17 mV 1.6 × 10-4 1.5 × 10-4 1.6 × 10-4 8.9 × 10-4 19 mV 1.5 × 10-4 1.3 × 10-4 1.5 × 10-4 8.2 × 10-4 0.12 V 8.0 × 10-4 5.3 × 10-4 8.0 × 10-4 0.14 V 7.0 × 10-4 5.5 × 10-4 7.0 × 10-4 0.14 V 4.7 × 10-4 3.7 × 10-4 4.7 × 10-4 0.70 V 1.4 × 10-3 0.70 V 8.8 × 10-4 0.70 V 7.0 × 10-4 0.031 kV

Fluke 8508A and Vitrek 4700


Parameter/Frequency



DC Voltage AC Current

50 Hz to 10 kHz

DC Current

Frequency

100 mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 400) V (400 to 1000) V 100 μA (0.1 to 0.4) mA (0.4 to 0.8) mA (0.8 to 1) mA (1 to 4) mA (4 to 8) mA (8 to 10) mA (10 to 40) mA (40 to 80) mA (80 to 100) mA (0.1 to 0.4) A (0.4 to 0.8) A (0.8 to 1) A (1 to 4) A (4 to 8) A (8 to 10) A (10 to 20) A (20 to 30) A (30 to 45) A 100 μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA (0.1 to 1) A (1 to 10) A (10 to 40) A (40 to 80) A (80 to 100) A 20 Hz (20 to 100) Hz 100 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz

6.9 μV 69 μV 0.69 mV 3.8 mV 0.069 V 0.69 V 71 nA 0.12 μA 0.15 μA 0.18 μA 1.1 μA 1.4 μA 1.6 μA 11 μA 14 μA 15 μA 0.11 mA 0.14 mA 0.16 mA 1.1 mA 1.5 mA 1.7 mA 7.5 mA 8.1 mA 9.3 mA 10 nA 64 nA 0.64 μA 6.4 μA 64 μA 0.68 mA 25 mA 48 mA 53 mA 9 μHz 7.8 × 10-7 8.4 × 10-7 9.8 × 10-7 7.5 × 10-7

Fluke 8508A Fluke 8508A and Fluke A40B current shunt set Fluke A40B current shunt set HP 53132A


Parameter/Frequency


Puncture/Safety Testers –

AC Voltage

50 Hz

60 Hz DC Voltage AC Cutoff Current

(50 to 60) Hz DC Cutoff Current

Insulation Voltage

0.1 kV (0.1 to 2) kV (2 to 10) kV (10 to 20) kV (20 to 30) kV (30 to 40) kV (40 to 50) kV (50 to 60) kV (60 to 70) kV 0.1 kV (0.1 to 1) kV (1 to 8) kV (8 to 10) kV (10 to 75) kV 0.1 kV (0.1 to 1) kV (1 to 6) kV (6 to 8) kV (8 to 30) kV (30 to 100) kV (0.5 to 10) mA (10 to 20) mA (20 to 50) mA (50 to 100) mA (0.5 to 10) mA (10 to 20) mA (20 to 50) mA (50 to 100) mA 50 V (50 to 300) V (300 to 500) V (500 to 800) V (0.8 to 1) kV (1 to 2) kV (2 to 6) kV (6 to 8) kV (8 to 10) kV

0.021 kV 2.1 × 10-2 1.7 × 10-2 5.5 × 10-3 7.0 × 10-3 7.8 × 10-3 8.2 × 10-3 8.5 × 10-3 8.7 × 10-3 0.022 kV 2.2 × 10-2 1.0 × 10-2 1.2 × 10-2 1.0 × 10-2 1.3 V 1.3 × 10-3 6.5 × 10-4 5.3 × 10-4 8.5 × 10-4 7.7 × 10-4 1.4 × 10-2 3.1 × 10-3 1.3 × 10-3 5.8 × 10-3 1.4 × 10-2 2.9 × 10-3 1.2 × 10-3 5.8 × 10-3 1.1 mV 3.1 × 10-5 2.2 × 10-5 1.6 × 10-5 1.3 × 10-3 7.0 × 10-4 6.5 × 10-4 5.3 × 10-4 8.3 × 10-4

Vitrek 4700 Kikusui TOS1200, Datron 1281, Clarostat 240-C Datron 1281 Vitrek 4700


Parameter/Frequency


Puncture/Safety Testers – (cont)

Insulation Resistance Ground Bond AC Current

(50 to 60) Hz Ground Bond Resistance

(50 to 60) Hz Operating Time

1 kΩ (1 to 10) kΩ (10 to 100) kΩ (0.1 to 1) MΩ (1 to 10) MΩ (10 to 100) MΩ (0.1 to 1) GΩ (1 to 10) GΩ (10 to 100) GΩ 2 A (2 to 4) A (4 to 10) A (10 to 20) A (20 to 60) A 100 mΩ (100 to 500) mΩ 1 s (1 to 30) s (30 to 60) s

0.58 Ω 7.0 × 10-5 6.3 × 10-5 3.5 × 10-4 1.2 × 10-3 1.2 × 10-3 2.7 × 10-3 6.6 × 10-3 1.2 × 10-2 7.7 mA 3.0 × 10-3 2.7 × 10-3 1.7 × 10-3 1.4 × 10-3 1.4 mΩ 1.3 × 10-2 1.0 × 10-2 2.3 × 10-3 1.2 × 10-3

Esi RS925D, Iet HRRS-B-8-100k-5kV Datron 1281 Fluke A40B current shunt set Rara IRH300 resistance set Tektronix DPO4102B, Tektronix P2100A

Power Recorders –

Power

(50 to 60) Hz AC Voltage

(50 to 60) Hz

(1 to 10) W (10 to 24) W (24 to 48) W (48 to 60) W (60 to 120) W (120 to 240) W (240 to 600) W 600 W to 1.2 kW (1.2 to 2.4) kW (2.4 to 4.8) kW (4.8 to 6) kW (6 to 12) kW (12 to 24) kW (24 to 50) kW (1 to 50) V (50 to 100) V (100 to 200) V (200 to 300) V (300 to 400) V

6.6 × 10-4 4.0 × 10-4 3.4 × 10-4 3.3 × 10-4 5.8 × 10-4 4.0 × 10-4 3.4 × 10-4 5.9 × 10-4 4.1 × 10-4 4.0 × 10-4 3.5 × 10-4 6.1 × 10-4 6.0 × 10-4 5.7 × 10-4 1.5 × 10-4 5.8 × 10-4 3.0 × 10-4 2.0 × 10-4 1.6 × 10-4

Fluke 6100A Fluke 5730A


Parameter/Frequency


Power recorders (cont)

AC Current

(50 to 60) Hz

(0.1 to 1) A (1 to 2) A (2 to 5) A (5 to 10) A (10 to 20) A (20 to 50) A (50 to 100) A (100 to 200) A

6.7 × 10-4 4.2 × 10-4 3.1 × 10-3 2.1 × 10-3 6.4 × 10-4 2.0 × 10-4 6.0 × 10-4 1.8 × 10-3

Fluke 5730A, Fluke 52120A and Fluke turn coil

AC Voltmeters –

DC Voltage

(1 to 2) mV (-1 to -2) mV (2 to 10) mV (-2 to -10) mV (10 to 100) mV (-10 to -100) mV (0.1 to 1) V (-0.1 to -1) V (1 to 10) V (-1 to -10) V (10 to 100) V (-10 to -100) V (100 to 1000) V (-100 to -1000) V

9.3 × 10-6 9.2 × 10-6 8.4 × 10-6 8.4 × 10-6 8.3 × 10-6 8.3 × 10-6 5.9 × 10-6 5.9 × 10-6 3.6 × 10-6 3.6 × 10-6 6.1 × 10-6 6.1 × 10-6 8.3 × 10-6 8.3 × 10-6

Fluke 5730A


Parameter/Range


AC Voltmeters –

AC Voltage

(1 to 2) mV

(2 to 10) mV (10 to 100) mV 100 mV to 1 V

40 Hz 100 Hz 1 kHz 10 kHz 20 kHz 50 kHz 100 kHz 500 kHz 1 MHz 40 Hz 100 Hz 1 kHz 10 kHz 20 kHz 50 kHz 100 kHz 500 kHz 1 MHz 40 Hz 100 Hz 1 kHz 10 kHz 20 kHz 50 kHz 100 kHz 500 kHz 1 MHz 10 Hz 20 Hz 40 Hz 100 Hz 1 kHz 10 kHz 20 kHz 50 kHz 100 kHz 500 kHz 1 MHz

1.9 × 10-3 1.9 × 10-3 2.2 × 10-3 5.2 × 10-3 5.8 × 10-3 1.9 × 10-3 1.7 × 10-3 1.7 × 10-3 1.7 × 10-3 3.3 × 10-4 3.3 × 10-4 3.3 × 10-4 3.6 × 10-4 6.0 × 10-4 1.4 × 10-3 1.8 × 10-3 2.5 × 10-3 1.1 × 10-3 5.9 × 10-5 5.9 × 10-5 5.9 × 10-5 5.9 × 10-5 5.9 × 10-5 1.2 × 10-4 1.8 × 10-4 7.0 × 10-4 7.2 × 10-4 2.2 × 10-4 7.1 × 10-5 3.7 × 10-5 1.9 × 10-5 1.8 × 10-5 2.5 × 10-5 1.8 × 10-5 4.7 × 10-5 5.9 × 10-5 5.0 × 10-4 5.2 × 10-4

Fluke 792A, Fluke 8508A


Parameter/Range


AC Voltmeter – (cont)

AC Voltage

(1 to 10) V

(10 to 100) V (100 to 1000) V

Frequency Frequency Response

0 dB (0.774 6 V) Output Voltage

(0 to 1) V

10 Hz 20 Hz 40 Hz 100 Hz 1 kHz 10 kHz 20 kHz 50 kHz 100 kHz 500 kHz 1 MHz (10 to 40) Hz (40 to 100) Hz 100 Hz to 1 kHz (1 to 10) kHz (10 to 20) kHz (20 to 50) kHz (50 to 100) kHz 40 Hz 100 Hz 1 kHz 10 kHz 20 kHz 1 Hz to 10 Hz 10 Hz to 1 kHz 1 kHz to 1 MHz (1 to 10) MHz (10 to 50) MHz 20 Hz to 100 kHz (100 to 200) kHz 100 Hz to 20 kHz (20 to 50) kHz

2.2 × 10-4 7.1 × 10-5 3.6 × 10-5 2.4 × 10-5 2.4 × 10-5 2.4 × 10-5 2.4 × 10-5 4.7 × 10-5 5.8 × 10-5 5.0 × 10-4 5.6 × 10-4 3.5 × 10-5 3.5 × 10-5 3.5 × 10-5 3.5 × 10-5 3.5 × 10-5 7.6 × 10-5 8.2 × 10-5 3.3 × 10-5 3.3 × 10-5 3.3 × 10-5 3.3 × 10-5 3.3 × 10-5 5.8 × 10-4 5.8 × 10-5 5.8 × 10-5 5.8 × 10-5 1.2 × 10-4 0.002 dB 0.005 dB 1.0 × 10-3 2.0 × 10-3

Fluke 792A, Fluke 8508A Agilent 33250A Fluke 5730A Fluke 5730A H.P 34401A


Parameter/Frequency


LF Amplifiers – Gain

DC to 1 kHz (1 to 10) kHz (10 to 100) kHz DC to 1 kHz (1 to 20) kHz (20 to 100) kHz

(0 to 1) V (1 to 10) V (10 to 100) V (0 to 1) V (1 to 10) V (10 to 100 V (0 to 1) V (1 to 10) V (10 to 100) V (0 to 60) dB (0 to 60) dB (0 to 40) dB

2.3 × 10-4 3.7 × 10-4 1.6 × 10-4 2.2 × 10-4 3.7 × 10-4 1.4 × 10-4 7.1 × 10-4 9.5 × 10-4 7.2 × 10-4 0.006 dB 0.007 dB 0.010 dB


DC/LF Attenuators –

20 Hz to 10 kHz (10 to 20) kHz (20 to 50) kHz (50 to 100) kHz

(0 to 60) dB (0 to 60) dB (0 to 60) dB (0 to 60) dB

0.006 dB 0.007 dB 0.011 dB 0.011 dB


Multimeter Calibrators –

DC Voltage

0 mV (0 to 100) mV (-0 to -100) mV (0.1 to 1) V (-0.1 to -1) V (1 to 10) V (-1 to -10) V (10 to 100) V (-10 to -100) V (100 to 1000) V (-100 to -1000) V

0.13 μV 7.6 × 10-6 7.6 × 10-6 4.0 × 10-6 4.0 × 10-6 4.0 × 10-6 4.0 × 10-6 5.7 × 10-6 5.7 × 10-6 5.9 × 10-6 5.9 × 10-6

Fluke 732B, Fluke 8508A


Parameter/Frequency


Multimeter Calibrators – (cont)

AC Voltage

10 Hz (10 to 40) Hz (40 to 100) Hz (100 to 500) Hz 500 Hz to 1 kHz

(1 to 10) kHz (10 to 20) kHz (20 to 30) kHz

(0.1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (0.1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V (0.1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V (0.1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V (0.1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V (0.1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V (0.1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V (0.1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V

2.5 × 10-4 2.3 × 10-4 2.3 × 10-4 2.3 × 10-4 5.3 × 10-5 2.8 × 10-5 3.2 × 10-5 3.7 × 10-5 4.6 × 10-5 5.3 × 10-5 2.9 × 10-5 3.2 × 10-5 3.7 × 10-5 4.6 × 10-5 5.3 × 10-5 2.9 × 10-5 3.2 × 10-5 3.7 × 10-5 4.6 × 10-5 5.3 × 10-5 2.9 × 10-5 3.2 × 10-5 3.7 × 10-5 4.6 × 10-5 5.4 × 10-5 2.8 × 10-5 3.2 × 10-5 3.7 × 10-5 4.7 × 10-5 5.4 × 10-5 2.8 × 10-5 3.2 × 10-5 3.7 × 10-5 4.7 × 10-5 9.4 × 10-5 5.4 × 10-5 5.6 × 10-5 8.1 × 10-5 1.5 × 10-4

Fluke 5790B


Parameter/Frequency



AC Voltage

(30 to 50) kHz (50 to 100) kHz

(100 to 200) kHz (200 to 300) kHz (300 to 500) kHz 500 kHz to 1 MHz (1 to 2) MHz (2 to 5) MHz (5 to 10) MHz (10 to 20) MHz

(0.1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 600) V (0.1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 600) V (0.1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 60) V (0.1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 60) V (0.1 to 100) mV (0.1 to 1) V (1 to 20) V (0.1 to 100) mV (0.1 to 1) V (1 to 20) V (0.1 to 100) mV (0.1 to 1) V (1 to 3) V (0.1 to 100) mV (0.1 to 1) V (1 to 3) V (0.1 to 100) mV (0.1 to 1) V (1 to 3) V (0.1 to 100) mV (0.1 to 1) V (1 to 3) V

9.4 × 10-5 5.4 × 10-5 5.6 × 10-5 8.1 × 10-5 1.5 × 10-4 2.0 × 10-4 8.3 × 10-5 9.4 × 10-5 1.1 × 10-4

5.8 × 10-4

3.1 × 10-4 1.9 × 10-4 2.2 × 10-4 2.3 × 10-4 3.1 × 10-4 1.9 × 10-4 2.2 × 10-4 2.3 × 10-4 4.7 × 10-4 3.0 × 10-4 4.6 × 10-4 1.1 × 10-3 1.1 × 10-3 1.4 × 10-3 6.2 × 10-4 5.9 × 10-4 5.9 × 10-4 1.2 × 10-3 1.2 × 10-3 5.9 × 10-4 1.2 × 10-3 1.2 × 10-3 1.2 × 10-3 1.8 × 10-3 1.8 × 10-3 1.2 × 10-3

Fluke 5790B


Parameter/Frequency



AC Voltage

(20 to 30) MHz

DC Current AC Current

10 Hz (10 to 40) Hz

(40 to 45) Hz

(0.1 to 100) mV (0.1 to 1) V (1 to 3) V 0 μA (0 to 100) μA (-0 to -100) μA (0.1 to 1) mA (-0.1 to -1) mA (1 to 10) mA (-1 to -10) mA (10 to 100) mA (-10 to -100) mA (0.1 to 1) A (-0.1 to -1) A (1 to 10) A (-1 to -10) A (10 to 20) A (-10 to -20) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 3) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 3) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 10) A (10 to 20) A

6.9 × 10-3 6.9 × 10-3 1.8 × 10-3

0.81 nA 8.7 × 10-6 8.7 × 10-6 9.9 × 10-6 9.9 × 10-6 1.0 × 10-5 1.0 × 10-5 6.5 × 10-6 6.5 × 10-6 6.6 × 10-6 6.6 × 10-6 1.5 × 10-5 1.5 × 10-5 4.0 × 10-5 4.0 × 10-5 3.2 × 10-4 2.9 × 10-4 2.9 × 10-4 2.9 × 10-4 2.9 × 10-4 9.9 × 10-4 7.1 × 10-5 3.6 × 10-5 4.5 × 10-5 4.4 × 10-5 4.5 × 10-5 2.5 × 10-4 7.3 × 10-5 3.7 × 10-5 4.3 × 10-5 4.4 × 10-5 4.5 × 10-5 2.9 × 10-4 2.9 × 10-4

Fluke 5790B FLUKE 8508A standard resistances FLUKE 8508A AC current shunts


Parameter/Frequency



AC Current

(45 to 100) Hz

(100 to 200) Hz (200 to 500) Hz 500 Hz to 1 kHz (1 to 2) kHz

(1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 10) A (10 to 20) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 10) A (10 to 20) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 10) A (10 to 20) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 10) A (10 to 20) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 10) A (10 to 20) A

7.3 × 10-5 3.7 × 10-5 4.3 × 10-5 4.4 × 10-5 4.7 × 10-5 4.9 × 10-5 4.7 × 10-5

7.2 × 10-5 3.8 × 10-5 4.3 × 10-5 4.5 × 10-5 4.7 × 10-5 4.9 × 10-5 4.7 × 10-5 7.2 × 10-5 3.7 × 10-5 4.3 × 10-5 4.4 × 10-5 4.5 × 10-5 6.3 × 10-5 4.8 × 10-5 7.2 × 10-5 3.7 × 10-5 4.3 × 10-5 4.5 × 10-5 4.3 × 10-5 4.9 × 10-5 4.8 × 10-5 7.3 × 10-5 3.7 × 10-5 4.3 × 10-5 4.3 × 10-5 4.4 × 10-5 4.9 × 10-5 4.8 × 10-5

FLUKE 8508A AC current shunts


Parameter/Frequency



AC Current

(2 to 5) kHz

(5 to 10) kHz (10 to 30) kHz

Resistance

Frequency

(1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 10) A (10 to 20) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 3) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA (0.1 to 0.33) A 0 Ω (0.1 to 1) Ω (1 to 10) Ω (10 to 100) Ω 100 Ω to 1 kΩ (1 to 10) kΩ (10 to 100) kΩ 100 kΩ to 1 MΩ (1 to 10) MΩ (10 to 100) MΩ (100 to 1000) MΩ (1 to 10) GΩ (10 to 100) GΩ (0.1 to 1) Hz (1 to 10) Hz (10 to 100) Hz (0.1 to 1) kHz (1 to 10) kHz (10 to 100) kHz (0.1 to 1) MHz (1 to 10) MHz (10 to 30) MHz

7.3 × 10-5 3.6 × 10-5 4.2 × 10-5 4.6 × 10-5 4.5 × 10-5 4.9 × 10-5 4.9 × 10-5

7.3 × 10-5 3.7 × 10-5 4.3 × 10-5 4.5 × 10-5 5.0 × 10-5 2.6 × 10-4 1.2 × 10-4 6.8 × 10-5 7.2 × 10-5 7.2 × 10-5 2.1 × 10-4

4.6 μΩ 9.9 × 10-6 2.5 × 10-5 7.8 × 10-6 7.4 × 10-6 5.0 × 10-6 7.5 × 10-6 1.0 × 10-5 1.2 × 10-5 2.5 × 10-5 4.2 × 10-4 5.8 × 10-4 5.8 × 10-4 5.8 × 10-7

5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 1.9 × 10-7

FLUKE 8508A AC current shunts Standard resistances HP 53132A


Parameter/Frequency


Multi-Function Calibrator –

DC Voltage (Meter)

DC Current (Meter)

Resistance (Meter)

AC Voltage (Meter) (10 to 40) Hz (40 to 500) Hz

(0.1 to 100) mV (-0.1 to -100) mV (0.1 to 1) V (-0.1 to -1) V (1 to 10) V (-1 to -10) V (10 to 100) V (-10 to -100) V (100 to 1000) V (-100 to -1000) V (1 to 100) μA (-1 to -100) μA (0.1 to 1) mA (-0.1 to -1) mA (1 to 10) mA (-1 to -10) mA (10 to 100) mA (-10 to -100) mA (0.1 to 1) A (-0.1 to -1) A (1 to 10) A (-1 to -10) A (10 to 20) A (-10 to -20) A (0.1 to 100) Ω (0.1 to 1) kΩ (1 to 10) kΩ (10 to 100) kΩ (0.1 to 1) MΩ (1 to 10) MΩ (10 to 100) MΩ (0.1 to 1) GΩ (1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V (1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V

1.4 × 10-5 1.4 × 10-5 7.0 × 10-6 7.0 × 10-6 3.9 × 10-6 3.9 × 10-6 6.7 × 10-6 6.7 × 10-6 8.9 × 10-6 8.9 × 10-6 1.4 × 10-4 1.4 × 10-4 5.6 × 10-5 5.6 × 10-5 5.2 × 10-5 5.2 × 10-5 4.7 × 10-5 4.7 × 10-5 1.2 × 10-4 1.2 × 10-4 1.0 × 10-4 9.9 × 10-5 1.0 × 10-4 9.9 × 10-5 7.0 × 10-6 7.0 × 10-6 4.7 × 10-6 7.2 × 10-6 1.0 × 10-5 1.2 × 10-5 2.5 × 10-5 6.2 × 10-4 1.2 × 10-4 5.3 × 10-5 5.3 × 10-5 5.3 × 10-5 1.6 × 10-4 1.1 × 10-4 4.7 × 10-5 4.7 × 10-5 5.3 × 10-5 1.1 × 10-4

Fluke 5730A Fluke 5730A, Fluke 5725A, Fluke 52120A Standard resistance Fluke 8508A


Parameter/Frequency


Multi-Function Calibrator – (cont)

AC Voltage (Meter)

500 Hz to 1 kHz (1 to 10) kHz (10 to 20) kHz (20 to 50) kHz (50 to 100) kHz

AC Current (Meter)

(10 to 40) Hz

(40 to 500) Hz

(1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V (1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V (1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V (1 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (0 to 100) mV (0.1 to 1) V (1 to 10) V (10 to 100) V (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA (0.1 to 1) A (1 to 10) A (10 to 20) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA (0.1 to 1) A (1 to 10) A (10 to 20) A

1.1 × 10-4 4.7 × 10-5 4.7 × 10-5 5.3 × 10-5 1.1 × 10-4 1.1 × 10-4 4.7 × 10-5 4.7 × 10-5 5.3 × 10-5 1.1 × 10-4 1.2 × 10-4 4.7 × 10-5 4.7 × 10-5 6.1 × 10-5 1.6 × 10-4 1.7 × 10-4 7.0 × 10-5 7.0 × 10-5 8.6 × 10-5 1.7 × 10-4 7.7 × 10-5 7.7 × 10-5 9.9 × 10-5 1.4 × 10-4 9.9 × 10-5 9.9 × 10-5 1.1 × 10-4 2.4 × 10-4 1.5 × 10-4 1.5 × 10-4 1.4 × 10-4 9.9 × 10-5 9.9 × 10-5 1.1 × 10-4 2.4 × 10-4 5.9 × 10-4 4.9 × 10-4



Parameter/Frequency



AC Current (Meter)

500 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz

DC Voltage – Generate DC Current – Generate

(1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA (0.1 to 1) A (1 to 10) A (10 to 20) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA (0.1 to 1) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA (0.1 to 1) A (0.1 to 100) mV (-0.1 to -100) mV (0.1 to 1) V (-0.1 to -1) V (1 to 10) V (-1 to -10) V (10 to 100) V (-10 to -100) V (100 to 1000) V (-100 to -1000) V (1 to 100) μA (-1 to -100) μA (0.1 to 1) mA (-0.1 to -1) mA (1 to 10) mA (-1 to -10) mA (10 to 100) mA (-10 to -100) mA (0.1 to 1) A (-0.1 to -1) A (1 to 10) A (-1 to -10) A

1.4 × 10-4 9.9 × 10-5 9.9 × 10-5 1.1 × 10-4 2.4 × 10-4

5.9 × 10-4 4.9 × 10-4 2.2 × 10-4 1.4 × 10-4 1.4 × 10-4 1.5 × 10-4 3.4 × 10-4 2.2 × 10-4 1.4 × 10-4 1.4 × 10-4 1.5 × 10-4 3.4 × 10-4 5.9 × 10-6 5.9 × 10-6 3.7 × 10-6 3.7 × 10-6 3.6 × 10-6 3.6 × 10-6 5.1 × 10-6 5.1 × 10-6 5.4 × 10-6 5.4 ×10-6 1.2 × 10-5 1.2 × 10-5 1.2 × 10-5 1.2 × 10-5 1.0 × 10-5 1.0 × 10-5 2.3 × 10-5 2.3 × 10-5 3.7 × 10-5 3.7 × 10-5 1.7 × 10-4 1.7 × 10-4

Fluke 8508A


Parameter/Frequency



Resistance – Generate

AC Current – Generate

(10 to 40) Hz (40 to 500) Hz 500 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz

(0.1 to 100) Ω (0.1 to 1) kΩ (1 to 10) kΩ (10 to 100) kΩ (0.1 to 1) MΩ (1 to 10) MΩ (10 to 100) MΩ (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA (0.1 to 1) A (1 to 10) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA (0.1 to 1) A (1 to 10) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA (0.1 to 1) A (1 to 10) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA (0.1 to 1) A (1 to 10) A (1 to 100) μA (0.1 to 1) mA (1 to 10) mA (10 to 100) mA (0.1 to 1) A (1 to 10) A

9.0 × 10-6 8.9 × 10-6 8.9 × 10-6 9.1 × 10-6 1.1 × 10-5 1.5 × 10-5 5.0 × 10-5 4.1 × 10-4 4.1 × 10-4 4.1 × 10-4 4.0 × 10-4 8.1 × 10-4 1.0 × 10-3 4.1 × 10-4 4.1 × 10-4 4.1 × 10-4 4.1 × 10-4 8.1 × 10-4 1.0 × 10-3 4.1 × 10-4 4.1 × 10-4 4.1 × 10-4 4.1 × 10-4 8.1 × 10-4 1.0 × 10-3 4.3 × 10-4 4.1 × 10-4 4.1 × 10-4 4.1 × 10-4 9.3 × 10-4 3.0 × 10-3 5.7 × 10-4 4.2 × 10-4 4.1 × 10-4 4.1 × 10-4 3.4 × 10-4 3.0 × 10-3

Fluke 8508A Fluke 5730A, Fluke 5725A, Fluke 52120A


Parameter/Frequency



DC Voltage (Electrical Temperature)

Time Mark

Frequency

Capacitance DC DC to 50 Hz (50 to 100) Hz DC to 1 kHz

(-10 to 0) mV (0 to 1) mV (1 to 10) mV (10 to 100) mV (0.1 to 1) V (0.1 to 1) ns (1to 10) ns (10 to 100) ns (0.1 to 1) μs (1 to 10) μs (10 to 100) μs (0.1 to 1) ms (1 to 10) ms (10 to 100) ms (0.1 to 1) s (0.1 to 1) Hz (1 to 10) Hz (10 to 100) Hz (0.1 to 1) kHz (1 to 10) kHz (10 to 100) kHz (0.1 to 1) MHz (1to 10) MHz (10 to 100) MHz (0.1 to 1) GHz (0.1 to 1) mF (1 to 10) mF (10 to 110) mF (10 to 100) μF (0.1 to 1) μF (1 to 10) μF (10 to 100) μF (0.1 to 1) pF (1 to 10) pF (10 to 100) pF (0.1 to 1) nF (1 to 10) nF (10 to 100) nF (0.1 to 1) μF (1 to 10) μF

5.9 × 10-5 5.9 × 10-5 5.9 × 10-5 5.9 × 10-5 5.8 × 10-5 2.7 × 10-3 2.7 × 10-4 2.7 × 10-5 2.8 × 10-6 6.4 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7

5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 5.8 × 10-7 6.0 × 10-4 1.1 × 10-4 4.8 × 10-4 6.5 × 10-4 6.2 × 10-4 6.2 × 10-4 6.5 × 10-4 6.9 × 10-4 6.8 × 10-4 6.2 × 10-4 6.2 × 10-4 6.2 × 10-4 6.2 × 10-4 6.2 × 10-4 6.2 × 10-4

Fluke 8508A HP 53132A HP 53132A HP 4284A


Parameter/Frequency



Capacitance

(1 to 10) kHz

(0.1 to 1) pF (1 to 10) pF (10 to 100) pF (0.1 to 1) nF (1 to 10) nF (10 to 100) nF

6.9 × 10-4 6.8 × 10-4 6.8 × 10-4 6.8 × 10-4 6.8 × 10-4 6.8 × 10-4

Oscilloscope Calibrators –

DC Voltage

-(2.5 to 0) mV -(2.5 to 5) mV -(5 to 10) mV -(10 to 25) mV -(25 to 50) mV -(50 to 100) mV -(100 to 250) mV -(250 to 500) mV -(0.5 to 1) V -(1 to 2.5) V -(2.5 to 5) V -(5 to 10) V -(10 to 25) V -(25 to 50) V -(50 to 100) V -(100 to 150) V -(150 to 200) V (0 to 2.5) mV (2.5 to 5) mV (5 to 10) mV (10 to 25) mV (25 to 50) mV (50 to 100) mV (100 to 250) mV (250 to 500) mV (0.5 to 1) V (1 to 2.5) V (2.5 to 5) V (5 to 10) V (10 to 25) V (25 to 50) V (50 to 100) V (100 to 150) V (150 to 200) V

6.0 × 10-5 3.1 × 10-5 6.0 × 10-5 2.5 × 10-5 1.3 × 10-5 5.8 × 10-5 2.4 × 10-5 1.2 × 10-5 5.8 × 10-5 2.4 × 10-5 1.2 × 10-5 5.8 × 10-5 2.4 × 10-5 1.3 × 10-5 5.8 × 10-5 3.9 × 10-5 3.0 × 10-5 5.8 × 10-5 3.0 × 10-5 6.0 × 10-5 2.5 × 10-5 1.3 × 10-5 5.8 × 10-5 2.4 × 10-5 1.2 × 10-5 5.8 × 10-5 2.4 × 10-5 1.2 × 10-5 5.8 × 10-5 1.2 × 10-5 1.3 × 10-5 5.8 × 10-5 3.9 × 10-5 3.0 × 10-5

Fluke 8508A


Parameter/Frequency


Oscilloscope Calibrators – (cont)

Square/Edge Wave Voltage

1 kHz

100 kHz Square/Edge Wave Frequency Edge TD Pulse Drive

(10 to 100) Hz (0.1 to 1) kHz

Edge Duty Cycle

Edge Rise Time

Leveled Sine Wave – Harmonic

50 kHz to 6 GHz

RF output level – V(p-p) 50 kHz to 600 MHz

600 MHz to 1.1 GHz

(1.1 to 6) GHz

(5 to 10) mV (10 to 25) mV (25 to 50) mV (50 to 100) mV (100 to 250) mV (250 to 500) mV 500 mV to 1 V (1 to 2.5) V (2.5 to 5) V (5 to 10) V (10 to 25) V (25 to 50) V (50 to 100) V (100 to 130) V (130 to 200) V (10 to 25) mV (25 to 50) mV (50 to 100) mV (100 to 250) mV (250 to 500) mV 500 mV to 1 V (1 to 2.5) V (0.01 to 10) MHz (11 to 100) V (11 to 100) V (10 to 50) % (300 to 500) ps (-10 to -80) dBc 50 mV to 5.5 V 50 mV to 3.5 V 50 mV to 1.2 V

7.4 × 10-4 4.2 × 10-4 3.3 × 10-4 2.8 × 10-4 2.5 × 10-4 1.5 × 10-4 2.0 × 10-4 1.6 × 10-4 2.3 × 10-4 2.0 × 10-4 1.6 × 10-4 2.3 × 10-4 2.0 × 10-4 1.8 × 10-4 1.7 × 10-4 1.2 × 10-4 1.2 × 10-4 1.2 × 10-4 3.9 × 10-5 3.9 × 10-5 7.0 × 10-5 5.0 × 10-5 5.8 × 10-8 2.8 × 10-5 2.8 × 10-5 1.2 × 10-3 1.0 × 10-2 0.76 dB 1.4 × 10-2 1.4 × 10-2 1.4 × 10-2

Fluke 8508A HP 53132A HP 3458A Fluke 8508A Tektronix DPO4102B Agilent E4440A Agilent E4417A


Parameter/Frequency


Oscilloscope Calibrators – (cont)

Leveled Sine Wave – Frequency

Leveled Sine Wave – Amplitude

(0.01 to 50) kHz

Wave Generator – Square (0.01 to 1) kHz (0.01 to 10) kHz

Wave Generator – Sine (0.01 to 1) kHz

Wave Generator – Triangle (0.01 to 1) kHz

Pulse Generator – Period

Pulse Generator – Width

Time Mark

(0.5 to 6) GHz (5 to 100) mV (0.1 to 1) V (1 to 5.5) V (0.01 to 3.75) V (2.5 to 55) V (0.01 to 55) V (0.01 to 55) V (0.01 to 20) μs (4 to 100) ns (1 to 5) ns (5 to 50) ns (50 to 500) ns 500 ns to 5 μs (5 to 50) μs (50 to 500) μs 500 μs to 5 ms (5 to 50) ms (50 to 500) ms 500 ms to 5 s (5 to 20) s

3.1 × 10-9 1.0 × 10-4 5.9 × 10-4 1.1 × 10-4 1.9 × 10-4 8.6 × 10-5 1.2 × 10-4 1.4 × 10-4 2.9 × 10-8 1.0 × 10-2 5.4 × 10-4 5.4 × 10-5 5.4 × 10-6 5.5 × 10-7 1.3 × 10-7 1.2 × 10-7 1.2 × 10-7 1.2 × 10-7 1.2 × 10-7 1.2 × 10-7 2.9 × 10-7

H.P 53132A Fluke 5790A Fluke 5790A Fluke 5790A Fluke 5790A HP 53132A Tektronix DPO4102B HP 53132A


Parameter/Frequency


Oscilloscope Calibrators (cont) –

Frequency MeasZ (Resistance) MeasZ (Capacitance)

(50 to 500) mHz 500 mHz to 5 Hz (5 to 50) Hz (50 to 500) Hz 500 Hz to 5 kHz (5 to 50) kHz (50 to 500) kHz 500 kHz to 5 MHz (5 to 50) MHz (50 to 500) MHz 500 MHz to 1.1 GHz 40 Ω to 1.5 MΩ (5 to 100) pF

1.2 × 10-7 1.2 × 10-7 1.2 × 10-7 1.2 × 10-7 1.2 × 10-7 1.2 × 10-7 1.2 × 10-7 1.2 × 10-7 1.2 × 10-7 1.2 × 10-7 5.2 × 10-7 2.7 × 10-4 3.0 × 10-3

H.P 53132A ESI DB62 H.P 4440B

Video Signal Generator –

DOT Frequency

SYNC Frequency

SYNC Width (Time)

Analog Video Level

Analog Sync Level

Audio Level

S-Video Level

Component Level

Scart Video Level

Scart Audio Level

10 kHz to 1000 MHz 50 Hz to 1 MHz (1 to 100) μs (100 to 1000) mV (1 to 5) V (100 to 1000) mV (100 to 1000) mV (100 to 1000) mV (100 to 1000) mV (100 to 1000) mV

5.8 × 10-7 5.8 × 10-7 1.2 × 10-3 1.3 × 10-2 1.3 × 10-2 1.3 × 10-2 1.3 × 10-2 1.3 × 10-2 1.3 × 10-2 1.3 × 10-2

H.P 53132A H.P 53132A Tektronix TDS694C Tektronix TDS694C Tektronix TDS694C Tektronix TDS694C Tektronix TDS694C Tektronix TDS694C Tektronix TDS694C Tektronix TDS694C


Parameter/Range


Video Signal Generator (cont) –

NTSC, PAL, SECAM H-Timing Test (Time) (Level) NTSC, PAL, SECAM COLOR BAR (LUMINANCE Level) NTSC, PAL, SECAM COLOR BAR (CHROMINANCE Level) NTSC, PAL, SECAM COLOR BAR (CHROMINACE Phase)

RF Frequency Sound Frequency SUB CARRIER Frequency

NTSC PAL

300 ns to 9 μs 300 ns to 9 μs (50 to 1000) mV (50 to 1000) mV (50 to 1000) mV 0˚ to 360˚ 10 kHz to 1000 MHz 10 Hz to 1 MHz 3.579 545 MHz 4.433 619 MHz

3.9 × 10-2 1.4 × 10-3 6.7 × 10-3 4.1 × 10-3 4.1 × 10-3 0.55˚ 5.8 × 10-7 5.8 × 10-7 0.58 Hz 0.58 Hz

Tektronix VM700T Tektronix VM700T Tektronix VM700T Tektronix VM700T H.P 53132A Tektronix VM700T

Audio Distortion Analyzers/Meters –

Audio Distortion Analyzers Input Frequency AC Input Levels

1 mV

(1 to 10) mV

(10 to 100) mV

1 Hz to 1 MHz 10 Hz 10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 10 Hz 10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 10 Hz 10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz

5.8 × 10-5 7.3 μV 5.4 × 10-3 6.4 × 10-3 8.6 × 10-3 4.2 × 10-3 3.3 × 10-3 3.8 × 10-3 5.0 × 10-3 1.2 × 10-3 4.8 × 10-4 6.5 × 10-4 1.1 × 10-3

Agilent 33250A Fluke 5730A


Parameter/Range


Audio Distortion Analyzers/Meters (cont) –

AC Input Levels

100 mV to 1 V (1 to 10) V

(10 to 100) V

(100 to 300) V

DC Input Levels Input Distortion

20 Hz to 20 kHz 20 Hz to 20 kHz

Distortion Meter Calibrators

Output Level

100 mV

100 mV to 1 V

10 Hz 10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 10 Hz 10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 10 Hz 10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 50 Hz 50 Hz to 1 kHz 1 mV to 300 V (-10 to -60) dB (-60 to -70) dB (-70 to -80) dB (0.01 to 30) % 20 Hz 20 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz 20 Hz 20 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz

6.7 × 10-4 5.8 × 10-4 5.9 × 10-4 6.0 × 10-4 8.1 × 10-4 5.8 × 10-4 6.1 × 10-4 6.3 × 10-4 6.8 × 10-4 5.9 × 10-4 6.6 × 10-4 1.3 × 10-3 4.6 × 10-4 2.3 × 10-4 5.8 × 10-4 0.40 dB 0.46 dB 0.61 dB 3.1 × 10-2 62 μV 6.0 × 10-4 7.1 × 10-4 7.1 × 10-4 5.9 × 10-4 5.9 × 10-4 6.3 × 10-4 9.1 × 10-4

Fluke 5730A Fluke 5730A Meguro MKS-682 Fluke 8508A


Parameter/Range


Audio Distortion Analyzers/Meters (cont) –

Distortion Meter Calibrators

Output Level (1 to 10) V

Output Distortion

20 Hz to 100 kHz

20 Hz 20 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz (-10 to -20) dB (-20 to -50) dB (-50 to -80) dB

5.9 × 10-4 5.9 × 10-4 6.3 × 10-4 9.1 × 10-4 0.88 dB 1.1 dB 1.4 dB

Fluke 8508A H.P 8563E

LF Filters –

Frequency Level

30 Hz to 30 MHz 20 Hz to 100 kHz

5.8 × 10-4 0.009 dB

H.P 53132A Agilent 33250A Fluke 8508A

LF/Audio Signal Analyzers –

Output Frequency Output Level

(1 to 100) mV 100 mV to 1 V (1 to 10) V (10 to 100) V

1 Hz to1 MHz 10 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz 10 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz 10 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz 10 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz

5.8 × 10-6 1.9 × 10-4 4.0 × 10-4 9.3 × 10-4 1.5 × 10-4 2.7 × 10-4 7.1 × 10-4 1.5 × 10-4 2.6 × 10-4 7.0 × 10-4 1.5 × 10-4 2.6 × 10-4 7.1 × 10-4

H.P 53132A Fluke 8508A


Parameter/Range


LF/Audio Signal Analyzers (cont) –

Output Level

(10 to -10) dBm (-10 to -30) dBm (-30 to -40) dBm

Output DC Offset Output Flatness Output Amplitude

20 Hz to 1 kHz (1 to 20) kHz (20 to 50) kHz (50 to 100) kHz

Output Impedance Input Frequency AC Input Levels

(1 to 100) mV 100 mV to 1 V (1 to 10) V (10 to 100) V (100 to 300) V

10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz (- 20 to 20) V 20 Hz to 20 kHz (20 to 100) kHz (-10 to -60) dB (-10 to -60) dB (-10 to -60) dB (-10 to -60) dB (50 to 600) Ω 1 Hz to 1 MHz 10 Hz to 20 kHz (20 to 100) kHz 10 Hz to 20 kHz (20 to 100) kHz 10 Hz to 20 kHz (20 to 100) kHz 10 Hz to 20 kHz (20 to 100) kHz 10 Hz to 1 kHz (1 to 10) kHz

0.0062 dB 0.0084 dB 0.0084 dB 0.0067 dB 0.0099 dB 0.0099 dB 0.0067 dB 0.0099 dB 0.0099 dB 5.8 × 10-5 0.0062 dB 0.0084 dB 0.0060 dB 0.0067 dB 0.0099 dB 0.0099 dB 1.2 × 10-4 5.8 × 10-5 2.5 × 10-4 4.6 × 10-4 1.6 × 10-4 1.5 × 10-4 1.6 × 10-4 1.4 × 10-4 1.2 × 10-4 2.0 × 10-4 2.3 × 10-4 2.7 × 10-4

Fluke 8508A HP 8903B HP 8903B Fluke 8508A Fluke 5730A


Parameter/Range


LF/Audio Signal Analyzers (cont) –

DC Input Levels Filter (Weight, Low, High, Pass, Etc.)

Distortion Factor

20 Hz to 20 kHz 20 Hz to 20 kHz

1 mV to 300 V 400 Hz to 80 kHz (-10 to -60) dB (-60 to -70) dB (-70 to -80) dB (0.001 to 0.01) % (0.01 to 30) %

5.9 × 10-5 1.9 × 10-4 0.31 dB 0.38 dB 0.55 dB 5.5 × 10-2 3.1 × 10-2

Fluke 5730A Fluke 5730A, Fluke 8508A Meguro MKS-682

Line Frequency Meters – Frequency

40 Hz to 1 kHz

5.8 × 10-4

Agilent 33250A

Function Generators –

Frequency Output Level

(1 mV to 100 mV) (100 mV to 1 V) (1 V to 10 V)

(10 V to 100 V) 10 Hz to 20 kHz 20 kHz to 50 kHz 50 kHz to 100 kHz 100 kHz to 100 MHz

1 mHz to 3 GHz 10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz (100 to 100) MHz 10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz (100 to 100) MHz 10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz (100 to 100) MHz 10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz (-60 to 20) dBm (-60 to 20) dBm (-60 to 20) dBm (-60 to 20) dBm

5.8 × 10-9 4.0 × 10-4 9.3 × 10-4 9.3 × 10-4 3.1 × 10-2 2.7 × 10-4 7.0 × 10-4 7.1 × 10-4 3.1 × 10-2 2.6 × 10-4 7.0 × 10-4 7.0 × 10-4 3.1 × 10-2 2.6 × 10-4 7.0 × 10-4 7.1 × 10-4 0.0060 dB 0.0067 dB 0.0099 dB 0.16 dB

Agilent 53132A Fluke 8508A


Parameter/Range

Frequency CMC2, 3, 4, 5 (±) Comments

Function Generators (cont) –

DC Offset Output Flatness Distortion Factor Output Amplitude

10 Hz to 1 kHz 20 kHz to 50 kHz 50 kHz to 100 kHz

Rise/Fall Time AM Modulation FM Modulation Duty Cycle

(-20 to 20) V 10 Hz to 100 kHz 100 kHz to 1 GHz 20 Hz to 100 MHz (0 to -60) dB (0 to -60) dB (0 to -60) dB 1 s to 100 ns (100 to 10) ns (10 to 1) ns (5 to 99) % (9 to 400) kHz (1 to 99) %

5.8 × 10-4 0.011 dB 0.017 dB 1.4 dB 0.0060 dB 0.0067 dB 0.0099 dB 1.2 × 10-3 1.3 × 10-3 5.9 × 10-3 1.2 × 10-2 1.2 × 10-2 5.8 × 10-3 %

Fluke 8508A H.P 8903B Agilent E4417A H.P 8563E H.P 8903B Tektronix TDS694C H.P 8902A H.P 8902A Tektronix TDS694C

Genescopes – Vertical Gain

100 mV to 10 V (10 to 100) V

1.2 × 10-2 1.2 × 10-2

Fluke 9500B

Parameter/Equipment


DC High Voltages Volt Meters –

(Positive) 1 V to 1 kV (1 to 5) kV (5 to 10) kV (10 to 20) kV (20 to 30) kV (30 to 40) kV (40 to 48) kV (Negative) 1 V to 1 kV (1 to 5) kV (5 to 10) kV (10 to 20) kV (20 to 30) kV (30 to 40) kV (40 to 48) kV

5.8 × 10-3 1.2 × 10-2 6.7 × 10-3 3.7 × 10-3 4.2 × 10-3 3.9 × 10-3 3.8 × 10-3 5.8 × 10-3 1.2 × 10-2 6.7 × 10-3 4.2 × 10-3 1.9 × 10-2 1.5 × 10-2 1.2 × 10-2

Fluke 5730A Matsusada AU-50R12 Bertan 210-30R


Parameter/Frequency


AC High Voltages Volt Meters –

(50 to 60) Hz

(0 to 1) kV (1 to 10) kV (10 to 20) kV (20 to 60) kV (60 to 70) kV

2.0 × 10-4 1.9 × 10-2 2.0 × 10-2 1.9 × 10-2 2.0 × 10-2

Fluke 5730A Phenix 6CP120/60-7.5

Leakage Current Testers – AC Current

10 Hz (10 to 40) Hz (0.04 to 1) kHz

100 μA (100 to 200) μA (200 to 500) μA (0.5 to 1) mA (1 to 2) mA (2 to 5) mA (5 to 10) mA (10 to 20) mA (20 to 50) mA (50 to 100) mA 100 μA (100 to 200) μA (200 to 500) μA (0.5 to 1) mA (1 to 2) mA (2 to 5) mA (5 to 10) mA (10 to 20) mA (20 to 50) mA (50 to 100) mA 20 μA (20 to 50) μA (50 to 100) μA (100 to 200) μA (200 to 500) μA (0.5 to 1) mA (1 to 2) mA (2 to 5) mA (5 to 10) mA (10 to 20) mA (20 to 50) mA (50 to 100) mA

78 nA 5.0 × 10-4 4.6 × 10-4 7.1 × 10-4 4.4 × 10-4 4.6 × 10-4 7.1 × 10-4 4.4 × 10-4 4.8 × 10-4 3.7 × 10-4 69 nA 4.0 × 10-4 3.2 × 10-4 6.6 × 10-4 3.7 × 10-4 3.2 × 10-4 6.6 × 10-4 3.7 × 10-4 3.2 × 10-4 2.5 × 10-4 14 nA 3.6 × 10-4 6.6 × 10-4 3.5 × 10-4 2.8 × 10-4 6.4 × 10-4 3.4 × 10-4 2.8 × 10-4 6.4 × 10-4 3.4 × 10-4 2.6 × 10-4 1.8 × 10-4

Fluke 5730A


Parameter/Equipment


Leakage Current Testers – DC Current

1 μA (1 to 2) μA (2 to 5) μA (5 to 10) μA (10 to 20) μA (20 to 50) μA (50 to 100) μA (100 to 200) μA (200 to 500) μA (0.5 to 1) mA (1 to 2) mA (2 to 5) mA (5 to 10) mA (10 to 20) mA (20 to 50) mA (50 to 100) mA

7.1 nA 3.6 × 10-3 1.4 × 10-3 1.0 × 10-3 5.5 × 10-4 2.4 × 10-4 6.3 × 10-4 3.2 × 10-4 1.4 × 10-4 6.2 × 10-4 3.1 × 10-4 1.4 × 10-4 6.2 × 10-4 3.1 × 10-4 1.4 × 10-4 8.6 × 10-5

Fluke 5730A

Parameter/Frequency


Leakage Current Testers – AC Voltage

(40 Hz)

1 mV (1 to 2) mV (2 to 5) mV (5 to 10) mV (10 to 20) mV (20 to 50) mV (50 to 100) mV (100 to 200) mV (200 to 500) mV (0.5 to 1) V (1 to 2) V (2 to 5) V (5 to 10) V (10 to 20) V (20 to 50) V (50 to 100) V

4.8 μV 2.5 × 10-3 1.1 × 10-3 5.9 × 10-4 4.6 × 10-4 3.2 × 10-4 2.0 × 10-4 3.4 × 10-4 1.9 × 10-4 6.3 × 10-4 3.3 × 10-4 2.0 × 10-4 1.4 × 10-4 3.3 × 10-4 2.2 × 10-4 1.5 × 10-4

Fluke 5730A


Parameter/Frequency


Leakage Current Testers – AC Voltage

(0.04 to 1) kHz (1 to 10) kHz

1 mV (1 to 2) mV (2 to 5) mV (5 to 10) mV (10 to 20) mV (20 to 50) mV (50 to 100) mV (100 to 200) mV (200 to 500) mV (0.5 to 1) V (1 to 2) V (2 to 5) V (5 to 10) V (10 to 20) V (20 to 50) V (50 to 100) V (100 to 200) V (200 to 500) V (500 to 1000) V 1 mV (1 to 2) mV (2 to 5) mV (5 to 10) mV (10 to 20) mV (20 to 50) mV (50 to 100) mV (100 to 200) mV (200 to 500) mV (0.5 to 1) V (1 to 2) V (2 to 5) V (5 to 10) V (10 to 20) V (20 to 50) V (50 to 100) V

4.8 μV 2.5 × 10-3 1.1 × 10-3 5.8 × 10-4 4.5 × 10-4 2.8 × 10-4 1.7 × 10-4 3.3 × 10-4 1.4 × 10-4 6.2 × 10-4 3.2 × 10-4 1.4 × 10-4 8.5 × 10-5 3.1 × 10-4 1.5 × 10-4 9.4 × 10-5 7.5 × 10-5 9.2 × 10-5 8.7 × 10-5 4.8 μV 2.5 × 10-3 1.1 × 10-3 5.8 × 10-4 4.5 × 10-4 2.8 × 10-4 1.7 × 10-4 3.3 × 10-4 1.4 × 10-4 6.2 × 10-4 3.2 × 10-4 1.4 × 10-4 8.5 × 10-5 3.1 × 10-4 1.5 × 10-4 9.4 × 10-5

Fluke 5730A


Parameter/Equipment


Leakage Current Testers – DC Voltage

1 mV (1 to 2) mV (2 to 5) mV (5 to 10) mV (10 to 20) mV (20 to 50) mV (50 to 100) mV (100 to 200) mV (200 to 500) mV (0.5 to 1) V (1 to 2) V (2 to 5) V (5 to 10) V (10 to 20) V (20 to 50) V (50 to 100) V (100 to 200) V (200 to 500) V (500 to 1000) V

0.80 μV 4.1 × 10-4 1.7 × 10-4 8.5 × 10-5 3.1 × 10-4 1.2 × 10-4 6.3 × 10-5 3.1 × 10-4 1.2 × 10-4 6.2 × 10-4 3.1 × 10-4 1.2 × 10-4 6.2 × 10-5 3.1 × 10-4 1.2 × 10-4 6.2 × 10-5 3.2 × 10-5 1.5 × 10-5 1.1 × 10-5

Fluke 5730A

Parameter/Frequency


Leakage Current Testers – Input Voltage to Output Current Ratio

(20 Hz) (20 to 50) Hz (50 to 60) Hz (60 to 100) Hz (100 to 200) Hz (200 to 500) Hz (0.5 to 1) kHz (1 to 2) kHz (2 to 5) kHz (5 to 10) kHz

5.00 mA (5 to 5.03) mA 5.03 mA (5.05 to 5.1) mA (5.18 to 5.38) mA (5.65 to 6.99) mA (5.85 to 10.21) mA (4.93 to 14.81) mA 2.667 mA (2.667 to 5.59) mA (5.59 to 18.76) mA 1.416 mA (1.416 to 3.289) mA (3.289 to 19.65) mA

6.2 μA 6.2 μA 6.2 μA 6.2 μA 6.2 μA 6.2 μA 6.2 μA 6.2 μA 0.64 μA 6.2 μA 6.3 μA 0.62 μA 0.64 μA 6.3 μA

Fluke 5730A


Parameter/Frequency


Leakage Current Testers – Input Voltage to Output Current Ratio (cont)

(10 to 20) kHz (20 to 50) kHz (50 to 100) kHz (100 to 200) kHz (200 to 500) kHz (0.5 to 1) MHz

(20 Hz) (20 to 50) Hz (50 to 60) Hz (60 to 100) Hz (100 to 200) Hz (200 to 500) Hz (0.5 to 1) kHz

(0.719 to 1.721) mA (1.721 to 19.92) mA (0.289 to 0.699) mA (0.699 to 20) mA (0.145 to 0.35) mA (0.35 to 20) mA (0.072 to 0.175) mA (0.175 to 20) mA (0.029 to 0.07) mA (0.07 to 20) mA (0.014 to 0.035) mA (0.035 to 20) mA 2.5 V (2.5 to 9.998) V (2.506 to 2.513) V (2.513 to 9.989) V (2.506 to 2.519) V (2.519 to 9.984) V (2.525 to 2.551) V (2.551 to 9.956) V (2.584 to 2.611) V (2.611 to 2.688) V (2.688 to 9.827) V 2.825 V (2.825 to 2.976) V (2.976 to 3.484) V (3.484 to 9.047) V 2.915 V (2.915 to 5.102) V (5.102 to 7.279) V

0.62 μA 6.3 μA 0.62 μA 6.4 μA 0.62 μA 6.7 μA 0.62 μA 9.8 μA 0.62 μA 29 μA 0.62 μA 45 μA 1.1 mV 2.1 mV 0.92 mV 1.6 mV 0.92 mV 1.6 mV 0.92 mV 1.5 mV 0.89 mV 0.90 mV 1.4 mV 0.98 mV 0.99 mV 1.1 mV 1.4 mV 0.99 mV 1.1 mV 1.3 mV

Fluke 5730A


Parameter/Frequency


Leakage Current Testers – Input Voltage to Output Current Ratio (cont)

(1 to 2) kHz (2 to 5) kHz (5 to 10) kHz (10 to 20) kHz (20 to 50) kHz (50 to 100) kHz (100 to 200) kHz (200 to 500) kHz (0.5 to 1) MHz

2.463 V (2.463 to 3.774) V (3.774 to 4.688) V (4.688 to 7.407) V 1.333 V (1.333 to 2.077) V (2.077 to 2.801) V (2.801 to 9.346) V 0.709 V (0.709 to 1.056) V (1.056 to 1.642) V (1.642 to 9.804) V 0.36 V (0.36 to 0.53) V (0.53 to 0.862) V (0.862 to 10) V 0.145 V (0.145 to 0.212) V (0.212 to 0.348) V (0.348 to 10) V 0.0725 V (0.0725 to 0.1062) V (0.1062 to 0.1748) V (0.1748 to 10) V 0.0361 V (0.0361 to 0.0531) V (0.0531 to 0.0877) V (0.0877 to 10) V 0.0145 V (0.0145 to 0.0212) V (0.0212 to 0.035) V (0.035 to 10) V 0.0072 V (0.0072 to 0.0106) V (0.0106 to 0.0175) V (0.0175 to 10) V

0.89 mV 0.95 mV 0.99 mV 1.2 mV 0.64 mV 0.89 mV 0.93 mV 1.5 mV 0.63 mV 0.79 mV 0.65 mV 1.5 mV 0.63 mV 0.64 mV 0.67 mV 3.0 mV 0.64 mV 0.72 mV 0.76 mV 8.2 mV 65 μV 73 μV 76 μV 1.7 mV 77 μV 78 μV 0.11 mV 6.6 mV 72 μV 82 μV 92 μV 16 mV 70 μV 78 μV 88 μV 27 mV

Fluke 5730A


Parameter/Equipment


Leakage Current Testers – Resistance

10 Ω (10 to 20) Ω (20 to 50) Ω (50 to 100) Ω (100 to 200) Ω (200 to 500) Ω (0.5 to 1) kΩ (1 to 2) kΩ (2 to 5) kΩ (5 to 10) kΩ (10 to 20) kΩ (20 to 50) kΩ (50 to 100) kΩ (100 to 200) kΩ (200 to 500) kΩ (0.5 to 1) MΩ

0.13 mΩ 4.0 × 10-5 1.7 × 10-5 1.2 × 10-5 3.8 × 10-5

1.7 × 10-5 1.2 × 10-5 4.0 × 10-5 1.8 × 10-5 1.2 × 10-5 4.9 × 10-5 2.2 × 10-5 1.3 × 10-5 6.0 × 10-5 2.6 × 10-5 1.6 × 10-5

Fluke 8508A

Leakage Current Testers – Capacitance @ 1 kHz

100 pF (100 to 200) pF (200 to 500) pF (0.5 to 1) nF (1 to 2) nF (2 to 5) nF (5 to 10) nF (10 to 20) nF (20 to 50) nF (50 to 100) nF (100 to 200) nF (200 to 500) nF (0.5 to 1) μF

0.87 fF 3.1 × 10-5 1.2 × 10-5 8.7 × 10-6 2.6 × 10-4 1.0 × 10-4 5.1 × 10-5 2.6 × 10-4 1.0 × 10-4 5.1 × 10-5 4.6 × 10-4 1.8 × 10-4 9.1 × 10-5

AH 2700A

Electronic AC/DC Loads –

DC Loads: CV Mode CC Mode

100 mV 100 mV to 1 000 V 100 mA 100 mA to 1 A (1 to 10) A (10 to 100) A (100 to 300) A (300 to 400) A

6.4 μV 1.2 × 10-4 6.4 μA 6.4 × 10-5 1.2 × 10-4 1.2 × 10-4 2.3 × 10-4 2.1 × 10-4

Fluke 5730A Fluke 8508A Fluke A40B Shunt Set Guildline 9230A Set Agilent N8731A


Parameter/Equipment


Electronic AC/DC Loads –

AC Loads: CV Mode (40 to 60) Hz CC Mode (40 to 60) Hz

Charging/Discharge Tester Charging Current Discharge Current Charging Voltage Sense Voltage (Meter)

100 mV 100 mV to 10 V (10 to 100) V (100 to 1000) V 100 mA (0.1 to 1) A (1 to 10) A 100 μA (0.0001 to 10) A (10 to 100) A (100 to 300) A (300 to 500) A (500 to 1000) A -100 μA (-0.0001 to -10) A (-10 to -100) A (-100 to -300) A (-300 to -500) A (-500 to -1000) A 100 mV (0.1 to 10) V (10 to 100) V (100 to 1000) V (1000 to 1500) V 100 mV 100 mV to 1000 V

16 μV 1.5 × 10-5 1.5 × 10-5 1.5 × 10-5 92 μA 1.2 × 10-3 2.3 × 10-3 6.4 nA 1.2 × 10-4 1.3 × 10-4 2.3 × 10-4 2.1 × 10-4 3.1 × 10-4 6.4 nA 1.2 × 10-4 1.3 × 10-4 2.3 × 10-4 2.1 × 10-4 3.1 × 10-4 6.2 μV 1.2 × 10-4 1.2 × 10-7 1.2 × 10-4 1.1 × 10-3 6.4 μV 1.2 × 10-4

Fluke FLUKE 5730A N4L PPA5511 Kikusui PCR-1000L Fluke 8508A Fluke A40B Shunt Set Guildline 9230A Set Fluke 8508A Fluke A40B Shunt Set Guildline 9230A Set Fluke 8508A Fluke 5730A


Parameter/Equipment


Analogue/Digital Multimeters –

DC Voltage DC Current Resistance

0 mV (-1000 to -100) V (-100 to -10) V (-10 to -1) V -1 V to -100 mV (-100 to 0.1) mV (0.1 to 100) mV 100 mV to 1 V (1 to 10) V (10 to 100) V (100 to 10 000) V (-20 to -10) A (-10 to -1) A -1 A to -100 mA (-100 to -10) mA (-10 mA to -1) mA -1 mA to -100 μA (-100 to -1) μA 0 μA (1 to 100) μA 100 μA to 1 mA (1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 10) A (10 to 20) A 0 Ω (0.1 to 100) Ω 100 Ω to 1 kΩ (1 to 10) kΩ (10 to 100) kΩ 100 kΩ to 1 MΩ (1 to 10) MΩ (10 to 100) MΩ 100 MΩ to 1 GΩ (1 to 10) GΩ

0.49 μV 8.3 × 10-6 6.1 × 10-6 3.6 × 10-6 5.9 × 10-6 8.3 × 10-6 8.3 × 10-6 5.9 × 10-6 3.6 × 10-6 6.1 × 10-6 8.3 × 10-6 9.9 × 10-5 9.9 × 10-5 9.3 × 10-5 4.7 × 10-5 4.7 × 10-5 4.7 × 10-5 1.2 × 10-4 8.1 nA 1.2 × 10-4 4.7 × 10-5 4.7 × 10-5 4.7 × 10-5 9.3 × 10-5 1.0 × 10-4 1.0 × 10-4 2.1 μΩ 4.0 × 10-6 4.0 × 10-6 4.6 × 10-6 7.2 × 10-6 1.0 × 10-5 1.2 × 10-5 2.5 × 10-5 4.2 × 10-5 5.8 × 10-4

Datron 4808 Fluke 5730A Fluke 5725A Fluke 52120A Standard Resistors


Parameter/Frequency


Analogue/Digital Multimeters – AC Voltage

(1 to 100) mV 100 mV to 1 V (1 to 10) V (10 to 100) V

(100 to 1000) V

(10 to 40) Hz (40 to 500) Hz 500 Hz to 1 kHz (1 to 10) kHz (10 to 20) kHz (20 to 50) kHz (50 to 100) kHz (100 to 200) kHz (200 to 500) kHz 500 kHz to 1 MHz (10 to 40) Hz (40 to 500) Hz 500 Hz to 1 kHz (1 to 10) kHz (10 to 20) kHz (20 to 50) kHz (50 to 100) kHz (100 to 200) kHz (200 to 500) kHz 500 kHz to 1 MHz (10 to 40) Hz (40 to 500) Hz 500 Hz to 1 kHz (1 to 10) kHz (10 to 20) kHz (20 to 50) kHz (50 to 100) kHz (100 to 200) kHz (200 to 500) kHz 500 kHz to 1 MHz (10 to 40) Hz (40 to 500) Hz 500 Hz to 1 kHz (1 to 10) kHz (10 to 20) kHz (20 to 50) kHz (50 to 100) kHz (40 to 500) Hz 500 Hz to 1 kHz (1 to 10) kHz (10 to 20) kHz (20 to 30) kHz

7.0 × 10-5 6.1 × 10-5 6.1 × 10-5 6.1 × 10-5 7.0 × 10-5 1.2 × 10-4 1.2 × 10-4 1.2 × 10-3 2.3 × 10-3 2.3 × 10-3 5.3 × 10-5 4.7 × 10-5 4.7 × 10-5 4.7 × 10-5 4.7 × 10-5 7.0 × 10-5 7.7 × 10-5 2.0 × 10-4 1.2 × 10-3 1.2 × 10-3 5.3 × 10-5 4.7 × 10-5 4.7 × 10-5 4.7 × 10-5 4.7 × 10-5 7.0 × 10-5 7.7 × 10-5 2.0 × 10-4 1.2 × 10-3 1.2 × 10-3 1.0 × 10-4 5.3 × 10-5 5.3 × 10-5 5.3 × 10-5 6.1 × 10-5 8.6 × 10-5 9.9 × 10-5 1.1 × 10-4 1.1 × 10-4 1.1 × 10-4 1.6 × 10-4 1.5 × 10-4

Fluke 5730A Fluke 5725A Fluke 52120A


Parameter/Frequency


Analogue/Digital Multimeters –

AC Current (10 to 100) μA 100 μA to 1 mA (1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 10) A

(10 to 20) A

Frequency

(10 to 40) Hz (40 to 500) Hz 500 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz (10 to 40) Hz (40 to 500) Hz 500 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz (10 to 40) Hz (40 to 500) Hz 500 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz (10 to 40) Hz (40 to 500) Hz 500 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz (10 to 40) Hz (40 to 500) Hz 500 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz (40 to 500) Hz 500 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz (40 to 500) Hz 500 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz 10 Hz to 10 MHz

1.4 × 10-4 1.4 × 10-4 1.4 × 10-4 2.2 × 10-4 2.2 × 10-4 9.9 × 10-5 9.9 × 10-5 9.9 × 10-5 1.4 × 10-4 1.4 × 10-4 9.9 × 10-5 9.9 × 10-5 9.9 × 10-5 1.4 × 10-4 1.4 × 10-4 1.1 × 10-4 1.1 × 10-4 1.1 × 10-4 1.5 × 10-4 1.5 × 10-4 2.4 × 10-4 2.4 × 10-4 2.4 × 10-4 3.4 × 10-4 3.4 × 10-4 5.7 × 10-4 5.7 × 10-4 5.8 × 10-4 5.8 × 10-4 5.5 × 10-4 5.5 × 10-4 4.7 × 10-4 4.8 × 10-4 5.9 × 10-6

Fluke 5730A Fluke 5725A Fluke 52120A HP 33120A


Parameter/Equipment


Noise Meters –

AC Level (rms & Q-peak), DC to 100 kHz Weighting Filter (DIN/AUDIO, JIS A CCIR, CCIR/ARM) 1 kHZ Frequency Response

(1 to 100) mV (100 to 300) mV 300 mV to 1 V (1 to 3) V (3 to 10) V (10 to 30) V (30 to 100) V (100 to 300) V 1 V 10 Hz to 100 kHz

1.5 × 10-3 1.9 × 10-3 1.4 × 10-3 1.9 × 10-3 1.4 × 10-3 2.0 × 10-3 1.5 × 10-3 1.9 × 10-3 1.4 × 10-3 0.015 dB

Fluke 5522A

Oscilloscopes –

DC Voltage

0 mV (0 to 5) mV (5 to 10) mV (10 to 25) mV (25 to 50) mV (50 to 100) mV (100 to 250) mV (250 to 500) mV 500 mV to 1 V (1 to 25) V (25 to 50) V (50 to 100) V (100 to 200) V 0 mV (0 to -5) mV (-5 to -10) mV (-10 to -25) mV (-25 to -50) mV (-50 to -100) mV (-100 to -250) mV (-250 to -500) mV (-0.5 to -1) V (-1 to -25) V (-25 to -50) V (-50 to -100) V (-100 to -200) V

0.76 μV 7.4 × 10-4 1.5 × 10-4 8.0 × 10-5 3.6 × 10-5 2.1 × 10-5 4.0 × 10-5 2.5 × 10-5 1.4 × 10-5 2.4 × 10-5 2.4 × 10-5 1.3 × 10-5 1.1 × 10-5 0.76 μV 7.5 × 10-4 1.5 × 10-4 8.0 × 10-5 3.6 × 10-5 2.1 × 10-5 4.0 × 10-5 2.5 × 10-5 1.4 × 10-5 2.4 × 10-5 2.4 × 10-5 1.3 × 10-5 1.1 × 10-5

Fluke 9500B


Parameter/Frequency


Oscilloscopes (cont) –

Square Wave Voltage, 1 kHz

Bandwidth Level 50 kHz to 100 MHz (100 to 550) MHz 550 MHz to 1.1 GHz (1.1 to 4) GHz (4 to 5) GHz (5 to 6) GHz (6 to 10) GHz (10 to 15) GHz (15 to 20) GHz (20 to 25) GHz (26 to 30) GHz (30 to 35) GHz (35 to 40) GHz

40 μV 40 μV to 5 mV (5 to 10) mV (10 to 25) mV (25 to 50) mV (50 to 250) mV 250 mV to 50 V (50 to 100) V (100 to 200) V 60 mV 0.06 V to 3 V 60 mV 0.06 V to 3 V 60 mV 0.06 V to 3 V 60 mV 0.06 V to 3 V 60 mV 0.06 V to 3 V 60 mV 0.06 V to 3 V 60 mV 0.06 V to 3 V 60 mV 0.06 V to 3 V 60 mV 0.06 V to 3 V 60 mV 0.06 V to 3 V 60 mV 0.06 V to 3 V 60 mV 0.06 V to 3 V 60 mV 0.06 V to 3 V

60 nV 7.0 × 10-3 3.5 × 10-3 2.3 × 10-3 1.6 × 10-3 1.4 × 10-3 1.2 × 10-3 1.2 × 10-3 1.2 × 10-3 1.2 mV 2.6 × 10-2 2.2 mV 3.9 × 10-2 2.8 mV 5.5 × 10-2 1.4 mV 2.3 × 10-2 1.4 mV 2.3 × 10-2 1.4 mV 2.3 × 10-2 1.4 mV 2.3 × 10-2 1.6 mV 2.8 × 10-2 2.2 mV 3.7 × 10-2 2.2 mV 3.7 × 10-2 2.2 mV 3.7 × 10-2 2.2 mV 3.7 × 10-2 2.2 mV 3.7 × 10-2

Fluke 9500B Fluke 9500B Keysight N5173B HP E4416A Agilent E9300A


Parameter/Frequency


Oscilloscopes (cont) –

Time Mark

Frequency AC Voltage, 50 Hz to 10 kHz

1 ns (1 to 5) ns (5 to 50) ns (50 to 500) ns 500 ns to 5 μs (5 to 50) μs (50 to 500) μs 500 to 5 ms (5 to 50) ms (50 to 500) ms 500 ms to 5 s (5 to 20) s 100 mHz (100 to 500) mHz 500 mHz to 5 Hz (5 to 50) Hz (50 to 500) Hz 500 Hz to 5 kHz (5 to 50) kHz (50 to 500) kHz 500 kHz to 5 MHz (5 to 50) MHz (50 to 500) MHz 500 MHz to 1.0 GHz 10 mV (10 to 25) mV (25 to 50) mV (50 to 100) mV (100 to 250) mV (250 to 500) mV (0.5 to 1) V (1 to 2.5) V (2.5 to 5) V (5 to 10) V (10 to 25) V (25 to 50) V (50 to 100) V

5.8 fs 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 0.82 μHz 8.2 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 5.8 × 10-6 7.0 μV 7.0 × 10-4 4.6 × 10-4 3.0 × 10-4 2.3 × 10-4 1.1 × 10-4 1.3 × 10-4 1.6 × 10-4 1.3 × 10-4 1.0 × 10-4 1.8 × 10-4 1.4 × 10-4 1.5 × 10-4

Fluke 9500B Fluke 5522A Fluke 5730A

LF Phase Meters, (45 to 60) Hz

(0 to 360)°

0.013°

Fluke 6100A


Parameter/Frequency


Random Wave Generators –

Frequency

Output Level

(1 mV to 100 mV) (100 mV to 1 V) (1 V to 10 V) (10 V to 100 V) (100 kHz to 100 MHz)

DC Offset Output Flatness

Distortion Factor Output Amplitude

(0 to -60) dB

Rise/Fall Time AM Modulation

FM Modulation Duty Cycle

100 mHz to 350 MHz DC to 20 kHz (20 to 50) kHz (50 to 100) kHz 100 kHz to 100 MHz 20 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 100 kHz to 100 MHz 20 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 100 kHz to 100 MHz 20 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz (-60 to 20) dBm (-20 to 20) V 10 Hz to 100 kHz 100 kHz to 350 MHz 20 Hz to 80 MHz 10 Hz to 1 kHz 20 kHz to 50 kHz 50 kHz to 100 kHz 1 s to 100 ns (100 to 10) ns (10 to 1) ns (5 to 99) % 9 kHz to 400 kHz (1 to 99) %

5.8 × 10-9 4.0 × 10-4 9.3 × 10-4 9.3 × 10-4 3.1 × 10-2 2.7 × 10-4 7.0 × 10-4 7.1 × 10-4 3.1 × 10-2 2.6 × 10-4 7.0 × 10-4 7.0 × 10-4 3.1 × 10-2 2.6 × 10-4 7.0 × 10-4 7.1 × 10-4 0.16 dB 5.8 × 10-4 0.011 dB 0.017 dB 1.4 dB 0.0060 dB 0.0067 dB 0.0099 dB 1.2 × 10-3 1.3 × 10-3 5.9 × 10-3 1.2 × 10-2 1.2 × 10-2 5.8 × 10-3

H.P 53132A Fluke 8508A Fluke 8508A H.P 8903B Agilent E4417A Agilent E9304A H18 H.P 8563E H.P 8903B Tektronix TDS694C H.P 8902A H.P 8902A Tektronix TDS694C


Parameter/Equipment


Voltage/Current Recorders –


(0.1 to 1) mV (1 to 2) mV (2 to 5) mV (5 to 10) mV (10 to 20) mV (20 to 50) mV (50 to 100) mV (100 to 200) mV (200 to 500) mV 500 mV to 1 V (1 to 2) V (2 to 5) V (5 to 10) V (10 to 20) V (20 to 50) V (50 to 100) V (100 to 200) V (200 to 500) V (500 to 1000) V (-0.1 to -1) mV (-1 to -2) mV (-2 to -5) mV (-5 to -10) mV (-10 to -20) mV (-20 to -50) mV (-50 to -100) mV (-100 to -200) mV (-200 to -500) mV -500 mV to -1 V (-1 to -2) V (-2 to -5) V (-5 to -10) V (-10 to -20) V (-20 to -50) V (-50 to -100) V (-100 to -200) V (-200 to -500) V (-500 to -1000) V (0.1 to 100) mA 100 mA to 1 A (-0.1 to -100) mA -100 mA to -1 A

6.2 × 10-4 3.1 × 10-4 1.7 × 10-4 9.0 × 10-5 4.8 × 10-5 1.2 × 10-4 5.9 × 10-5 3.1 × 10-5 1.2 × 10-4 5.8 × 10-5 2.9 × 10-5 1.2 × 10-4 5.8 × 10-5 3.2 × 10-5 1.2 × 10-4 5.8 × 10-5 3.2 × 10-5 1.2 × 10-4 5.8 × 10-5 6.2 × 10-4 3.1 × 10-4 1.7 × 10-4 9.0 × 10-5 4.8 × 10-5 1.2 × 10-4 5.9 × 10-5 3.1 × 10-5 1.2 × 10-4 5.8 × 10-5 2.9 × 10-5 1.2 × 10-4 5.8 × 10-5 3.2 × 10-5 1.2 × 10-4 5.8 × 10-5 3.2 × 10-5 1.2 × 10-4 5.8 × 10-5 8.2 × 10-5 1.5 × 10-4 8.2 × 10-5 1.5 × 10-4



Parameter/Equipment


Relay Test Sets –

AC Voltage

(20 to 55 Hz)

(55 Hz to 300 Hz)

(300 Hz to 1 kHz)

AC Current

(20 to 55 Hz)

(55 Hz to 300 Hz)

(300 Hz to 1 kHz) (20 Hz to 1 kHz)


(0.1 to 100) mV 100 mV to 1 V (1 to 10) V (10 to 100) V (100 to 1000) V (0.1 to 100) mV 100 mV to 1 V (1 to 10) V (10 to 100) V (100 to 1000) V (0.1 to 100) mV 100 mV to 1 V (1 to 10) V (10 to 100) V (100 to 1000) V (0.1 to 100) mA 100 mA to 10 A (0.1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 10) A (0.1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 10) A (10 to 20) A (20 to 50) A (50 to 100) A 0 mV to 1 V (1 to 5) V (5 to 1000) V (0 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 10) A (10 to 20) A (20 to 50) A (50 to 100) A

2.4 × 10-4 1.5 × 10-4 1.5 × 10-4 1.5 × 10-4 1.4 × 10-4 1.6 × 10-4 1.1 × 10-4 1.1 × 10-4 1.1 × 10-4 1.4 × 10-4 1.5 × 10-4 1.1 × 10-4 1.1 × 10-4 1.1 × 10-4 1.4 × 10-4 7.0 × 10-5 8.0 × 10-5 6.7 × 10-5 6.4 × 10-5 7.2 × 10-5 8.0 × 10-5 6.7 × 10-5 7.0 × 10-5 7.2 × 10-5 1.1 × 10-4 1.3 × 10-3 1.2 × 10-3 1.3 × 10-3 5.8 × 10-5 1.2 × 10-4 5.8 × 10-5 6.0 × 10-5 7.3 × 10-5 2.2 × 10-4 4.7 × 10-4 7.0 × 10-4 6.0 × 10-4 5.9 × 10-4

Fluke 8508A Fluke 8508A Ballantine 1625A Fluke 8508A Fluke 8508A Ballantine 1625A


Parameter/Equipment


Relay Test Sets (cont) –

Frequency

40 Hz to 60 Hz 60 Hz to 100 Hz 100 Hz to 400 Hz 400 Hz to 1 kHz

1.2 × 10-4 1.3 × 10-4 1.2 × 10-4 1.3 × 10-4

HP 34401A

LF Signal Generators –

Frequency

Output Level

(1 to 100) mV 100 mV to 1 V

(1 to 10) V (10 to 100) V (-60 to 20) dBm

DC Offset

Output Flatness

100 mHz to 2 MHz DC to 20 kHz (20 to 50) kHz (50 to 100) kHz 100 kHz to 1 MHz 20 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 100 kHz to 1 MHz 20 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 100 kHz to 1 MHz 20 Hz to 20 kHz (20 to 50) kHz (50 to 1) kHz 10 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 100 kHz to 1 MHz (-20 to 20) V 10 Hz to 100 kHz 100 kHz to 1 MHz

5.8 × 10-9 4.0 × 10-4 9.3 × 10-4 9.3 × 10-4 3.1 × 10-2 2.7 × 10-4 7.0 × 10-4 7.1 × 10-4 3.1 × 10-2 2.6 × 10-4 7.0 × 10-4 7.0 × 10-4 3.1 × 10-2 2.6 × 10-4 7.0 × 10-4 7.1 × 10-4 0.0060 dB 0.0067 dB 0.0099 dB 0.16 dB 5.8 × 10-4 0.011 dB 0.017 dB

HP 53132A Fluke 8508A Fluke 8508A H.P 8903B Agilent E4417A Agilent E9304A H18


Parameter/Equipment


LF Signal Generators –

Distortion Factor

Output Amplitude (0 to -60) dB

Rise/Fall Time

AM Modulation

FM Modulation

Duty Cycle

20 Hz to 1 MHz 10 Hz to 1 kHz 20 kHz to 50 kHz 50 kHz to 100 kHz 1 s to 100 ns (100 to 10) ns (10 to 1) ns (5 to 990 % (9 to 400) kHz (1 to 99) %

1.4 dB 0.0060 dB 0.0067 dB 0.0099 dB 1.2 × 10-3 1.3 × 10-3 5.9 × 10-3 1.2 × 10-2 1.2 × 10-2 5.8 × 10-3

HP 8563E HP 8903B Tektronix TDS694C HP 8902A HP 8902A Tektronix TDS694C

LF Spectrum Analyzers –

Output Frequency 27 dBm

(27 to 10) dBm

(10 to -10) dBm

(-10 to -40) dBm

(-40 to -50) dBm

10 Hz to 20 kHz 20 kHz to 100 kHz 10 Hz to 20 kHz 20 kHz to 100 kHz 100 kHz to 200 kHz 10 Hz to 20 kHz 20 kHz to 100 kHz 100 kHz to 200 kHz 10 Hz to 20 kHz 20 kHz to 100 kHz 100 kHz to 200 kHz 10 Hz to 20 kHz 20 kHz to 100 kHz 100 kHz to 200 kHz

0.022 dB 0.032 dB 0.007 dB 0.007 dB 0.014 dB 0.006 dB 0.006 dB 0.008 dB 0.007 dB 0.008 dB 0.024 dB 0.015 dB 0.020 dB 0.067 dB

Agilent 33250A


Parameter/Equipment

Range CMC2, 3. 5 (±) Comments

LF Spectrum Analyzers – (cont)

Output Frequency (10 to 100) mV

100 mV to 1 V

(1 to 10) V (10 to 30) V

Input Frequency

Input Impedance

10 Hz to 10 kHz 10 kHz to 100 kHz 100 kHz to 200 kHz 10 Hz to 10 kHz 10 kHz to 100 kHz 100 kHz to 200 kHz 10 Hz to 10 kHz 10 kHz to 100 kHz 100 kHz to 200 kHz 10 Hz to 10 kHz 10 kHz to 100 kHz 10 Hz to 200 kHz 1 MΩ

6.3 × 10-3 7.4 × 10-3 7.4 × 10-3 6.0 ×10-3 5.9 × 10-3 8.3 × 10-3 6.0 × 10-3 5.9 × 10-3 7.1 × 10-3 3.3 × 10-3 3.5 × 10-3 5.8 × 10-5 5.8 × 10-4

Fluke 5730A H.P 53132A Fluke 8508A

Output Level (AC)

(10 to 100) mV 100 mV to 1 V

(1 to 10) V

Output Level (DC)

10 Hz to 1 kHz 1 kHz to 10 kHz 10 kHz to 100 kHz 10 Hz to 1 kHz 1 kHz to 10 kHz 10 kHz to 100 kHz 10 Hz to 1 kHz 1 kHz to 10 kHz 10 kHz to 100 kHz 10 mV to 10 V

6.0 × 10-4 7.0 × 10-4 1.1 × 10-3 5.9 × 10-4 6.3 × 10-4 9.1 × 10-4 5.8 × 10-4 5.9 × 10-4 6.7 × 10-4 5.8 × 10-5


Parameter/Equipment

Range CMC2, 3. 5 (±) Comments

Sweep Generators –

Frequency

Output level

1 mV to 100 mV 100 mV to 1 V (1 to 10) V (10 to 100) V (-60 to 20) dBm

100 mHz to 21 MHz DC to 20 kHz (20 to 50) kHz (50 to 100) kHz 100 kHz to 21 MHz 20 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 100 kHz to 21 MHz 20 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 100 kHz to 21 MHz 20 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 100 kHz to 21 MHz

5.8 × 10-9 4.0 × 10-4 9.3 × 10-4 9.3 × 10-4 3.1 × 10-2 2.7 × 10-4 7.0 × 10-4 7.1 × 10-4 3.1 × 10-2 2.6 × 10-4 7.0 × 10-4 7.0 × 10-4 3.1 × 10-2 2.6 × 10-4 7.0 × 10-4 7.1 × 10-4 0.16 dB



Parameter/Equipment


Sweep Generators (cont) –

DC Offset

Output flatness

Distortion factor

Output amplitude (0 to -60) dB

Rise/Fall Time

AM Modulation

FM Modulation

Duty Cycle

(-20 to 20) V 10 Hz to 100 kHz 100 kHz to 21 MHz 20 Hz to 21 MHz 10 Hz to 1 kHz (20 to 50) kHz (50 to 100) kHz 1 s to 100 ns (100 to 10) ns (10 to 1) ns (5 to 99) % (9 to 400) kHz (1 to 99) %

5.8 × 10-4 0.011 dB 0.017 dB 1.4 dB 0.006 0 dB 0.006 7 dB 0.009 9 dB 1.2 × 10-3 1.3 × 10-3 5.9 × 10-3 1.2 × 10-2 1.2 × 10-2 5.8 × 10-3

Fluke 8508A H.P 8903B Agilent E4417A Agilent E9304A H18 H.P 8563E H.P 8903B Tektronix TDS694C H.P 8902A H.P 8902A Tektronix TDS694C

Transistor Curve Tracers –

DC Voltage (SMU, Base/Emitter/Collector)

(-1000 to -200) V (-200 to -100) V (-100 to -10) V (-10 to -1) V (-1 to -0.1) V (-0.1 to 0) V (0 to 0.1) V (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 200) V (200 to 1000) V

4.8 × 10-6 4.7 × 10-6 5.1 × 10-6 3.7 × 10-6 6.9 × 10-6 5.9 × 10-6 5.9 × 10-6 6.9 × 10-6 3.7 × 10-6 5.1 × 10-6 4.7 × 10-6 4.8 × 10-6

Fluke 8508A


Parameter/Equipment


Transistor Curve Tracers (cont) –

DC Voltage (VSU, Base/Emitter/Collector) VMU (Base/Emitter/Collector) DC Current (SMU, Base/Emitter/Collector)

(-1000 to -200) V (-200 to -100) V (-100 to -10) V (-10 to -1) V (-1 to -0.1) V (-0.1 to 0) V (0 to 0.1) V (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 200) V (200 to 1000) V (-1000 to -200) V (-200 to -100) V (-100 to -10) V (-10 to -1) V (-1 to -0.1) V (-0.1 to 0) V (0 to 0.1) V (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 200) V (200 to 1000) V (-2 to -1) A -1 A to -100 mA (-100 to -10) mA (-10 to -1) mA -1 mA to -100 µA (-100 to -10) µA (-10 to -1) µA -1 µA to -100 nA (-100 to -10) nA (-10 to -1) nA -1 nA to -100 pA (-100 to -10) pA (-10 to -1) pA

4.8 × 10-6 4.7 × 10-6 5.1 × 10-6 3.7 × 10-6 6.9 × 10-6 5.9 × 10-6 5.9 × 10-6 6.9 × 10-6 3.7 × 10-6 5.1 × 10-6 4.7 × 10-6 4.8 × 10-6 4.8 × 10-6 4.7 × 10-6 5.1 × 10-6 3.7 × 10-6 6.9 × 10-6 5.9 × 10-6 5.9 × 10-6 6.9 × 10-6 3.7 × 10-6 5.1 × 10-6 4.7 × 10-6 4.8 × 10-6 6.7 × 10-4 3.8 × 10-4 4.8 × 10-5 1.5 × 10-5 1.4 × 10-5 1.4 × 10-5 5.4 × 10-5 4.7 × 10-4 2.4 × 10-3 2.4 × 10-3 5.8 × 10-3 1.2 × 10-2 1.2 × 10-2

Fluke 8508A Fluke 8508A Fluke 5730A Fluke 8508A Keithley 6517A Guildline 9330-100 kΩ Guildline 9330-1 MΩ Fluke 742A-10M IET LABS HRRS-B-8-100k-5kV


Parameter/Equipment


Transistor Curve Tracers (cont) –

DC Current (SMU, Base/Emitter/Collector)

(-1 to 0) pA (0 to 1) pA (1 to 10) pA (10 to 100) pA 100 pA to 1 nA (1 to 10) nA (10 to 100) nA 100 nA to 1 µA (1 to 10) µA (10 to 100) µA 100 µA to 1 mA (1 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 2) A

1.5 × 10-2 1.5 × 10-2 1.2 × 10-2 1.2 × 10-2 5.8 × 10-3 2.4 × 10-3 2.4 × 10-3 4.7 × 10-4 5.4 × 10-5 1.4 × 10-5 1.4 × 10-5 1.5 × 10-5 4.8 × 10-5 3.8 × 10-4 6.7 × 10-4

Fluke 8508A Keithley 6517A Guildline 9330-100 kΩ Guildline 9330-1 MΩ Fluke 742A-10M IET LABS HRRS-B-8-100k-5kV

Waveform Analyzers –


(1 mV to 100 mV) (100 mV to 1 V) (1 V to 10 V) (10 V to 100 V)

1 Hz to 1 MHz 10 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz 10 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz 10 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz 10 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz

5.8 × 10-6 1.9 × 10-4 4.0 × 10-4 9.3 × 10-4 1.5 × 10-4 2.7 × 10-4 7.1 × 10-4 1.5 × 10-4 2.6 × 10-4 7.0 × 10-4 1.5 × 10-4 2.6 × 10-4 7.1 × 10-4



Parameter/Equipment


Waveform Analyzers (cont) –

Output DC Offset Output Flatness Output Amplitude

(-10 to -60) dB

Output Impedance Input Frequency AC Input Level

(1 mV to 100 mV) 100 mv to 1 V (1 V to 10 V)

(10 V to 100 V)

(100 V to 300 V)

- 20 V to 20 V 20 Hz to 20 kHz (20 to 100) kHz 20 Hz to 1 kHz (1 to 20) kHz (20 to 50) kHz (50 to 100) kHz (50 to 600) Ω 1 Hz to 1 MHz 10 Hz to 20 kHz (20 to 100) kHz 100 mV to 1 V 10 Hz to 20 kHz (20 to 100) kHz 10 Hz to 20 kHz (20 to 100) kHz 10 Hz to 20 kHz (20 to 100) kHz 10 Hz to 1 kHz (1 to 10) kHz

5.8 × 10-5 0.0062 dB 0.0084 dB 0.0060 dB 0.0067 dB 0.0099 dB 0.0099 dB 1.2 × 10-4 5.8 × 10-5 2.5 × 10-4 4.6 × 10-4 1.6 × 10-4 1.5 × 10-4 1.6 × 10-4 1.4 × 10-4 1.2 × 10-4 2.0 × 10-4 2.3 × 10-4 2.7 × 10-4

Fluke 8508A H.P 8903B H.P 8903B Fluke 8508A Agilent 33250A Fluke 5730A


Parameter/Equipment


Waveform Analyzers (cont) –

DC Input Level Filter (Weight, Low, High Pass, etc.) Distortion Factor

(-10 to -60) dB (-60 to -70) dB (-70 to -80) dB

(0.001 to 0.01) % (0.01 to 30) %

1 mV to 300 V 400 Hz to 80 kHz 20 Hz to 20 kHz 20 Hz to 20 kHz 20 Hz to 20 kHz 20 Hz to 20 kHz 20 Hz to 20 kHz

5.9 × 10-5 1.9 × 10-4 0.31 dB 0.38 dB 0.55 dB 5.5 × 10-2 3.1 × 10-2

Fluke 5730A Fluke 5730A Meguro MKS-682

AC/DC High Voltage Generators –

DC Voltage AC Voltage, (50 to 60) Hz

(0 to 1) kV (1 to 10) kV (10 to 20) kV (20 to 30) kV (30 to 50) kV (50 to 80) kV (80 to 90) kV (90 to 95) kV (-0 to -1) kV (-1 to -10) kV (-10 to -20) kV (-20 to -30) kV (-30 to -50) kV (-50 to -80) kV (-80 to -90) kV (-90 to -95) kV (0.1 to 1) kV (1 to 10) kV (10 to 20) kV (20 to 60) kV (60 to 70) kV

5.4 × 10-6 7.3 × 10-4 7.2 × 10-4 7.3 × 10-4 7.2 × 10-4 7.1 × 10-4 7.2 × 10-4 7.8 × 10-4 5.4 × 10-6 7.3 × 10-4 7.2 × 10-4 7.3 × 10-4 7.2 × 10-4 7.1 × 10-4 7.2 × 10-4 7.8 × 10-4 1.3 × 10-4 1.5 × 10-2 1.6 × 10-2 1.5 × 10-2 1.4 × 10-2

Fluke 8508A Vitrek 4700


Parameter/Equipment


AC/DC High Voltage Probes –

DC Voltage AC Voltage

10 Hz to 50 Hz 50 Hz to 60 Hz 60 Hz to 1 kHz

Resistance Capacitance @ 1 kHz

(1 to 100) V 100 to 1 kV (1 to 10) kV (10 to 20) kV (20 to 30) kV (30 to 40) kV (-1 to -100) V -100 V to -1 kV (-1 to -10) kV (-10 to -20) kV (-20 to -30) kV (-30 to -40) kV (1 to 100) V 100 V to 1 kV (1 to 100) V 100 V to 1 kV (1 to 10) kV (10 to 20) kV (20 to 60) kV (60 to 70) kV (1 to 100) V 100 V to 1 kV (1 to 10) Ω (10 to 100) Ω 100 Ω to 10 kΩ (10 to 100) kΩ 100 kΩ to 10 MΩ (10 to 100) MΩ 100 MΩ to 1 GΩ (0.1 to 1) pF (1 to 10) pF (10 to 100) pF 100 pF to 1 nF (1 to 10) nF

5.8 × 10-5 5.8 × 10-4 7.0 × 10-3 4.9 × 10-3 4.2 × 10-3 3.9 × 10-3 5.8 × 10-5 5.8 × 10-4 7.0 × 10-3 4.9 × 10-3 4.2 × 10-3 3.9 × 10-3 1.2 × 10-4 6.1 × 10-4 1.2 × 10-4 6.1 × 10-4 1.9 × 10-2 2.0 × 10-2 1.9 × 10-2 2.0 × 10-2 1.2 × 10-4 6.1 × 10-4 5.8 × 10-4 5.8 × 10-5 5.8 × 10-4 5.8 × 10-5 5.8 × 10-4 1.8 × 10-4 1.5 × 10-3 5.8 × 10-3 9.1 × 10-4 6.1 × 10-4 5.8 × 10-3 8.7 × 10-4

Fluke 5730A Bertan 210-30R Matsusada AU-50R12 Fluke 8508A Fluke 5730A Phenix 6CP120/60-7.5 Fluke 8508A Fluke 8508A H.P 4284A

Logic analyzers – Input voltage

(-10 to 10) V

5.8 × 10-5

Fluke 5730A


Parameter/Equipment


Telephone Testers –

Frequency AC Amplitude

(1 to 100) mV 100 mV to 1 V (1 to 10) V (10 to 100) V (100 to 500) V

(20 to -10) dBm

(-10 to -40) dBm

Loop Current DC Voltage Dial Level Resistance

1 Hz to1 MHz 20 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 20 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 20 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 20 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz 100 Hz to 1 kHz DC to 20 kHz (20 to 100) kHz DC to 20 kHz (20 to 100) kHz (1 to 100) mA 100 mA to 1 A 10 mV to 100 V (100 to 500) V (-39 to 10) dBm (50 to 1000) Ω

5.8 × 10-7 1.9 × 10-4 4.0 × 10-4 9.3 × 10-4 1.2 × 10-4 2.7 × 10-4 7.1 × 10-4 1.5 × 10-4 2.6 × 10-4 7.0 × 10-4 1.5 × 10-4 2.6 × 10-4 7.1 × 10-4 1.2 × 10-4 0.0062 dB 0.0084 dB 0.0067 dB 0.0099 dB 5.8 × 10-4 6.1 × 10-4 5.8 × 10-4 1.2 × 10-4 0.58 dB 5.8 × 10-4

H.P 53132A Fluke 8508A Fluke 8508A Fluke 8508A Jungjin 9407 Fluke 8508A


Parameter/Equipment


Video Signal Analyzers –

Square Wave level Sine Wave level Burst Frequency Vector Scopes, Video Signal Monitors Color Bar Level (Chrominance) Color Bar Phase Frequency Vertical Level

(0 to 100) mV (100 to 200) mV (200 to 300) mV (300 to 400) mV (400 to 500) mV (500 to 600) mV (600 to 1 000) mV (0 to 100) mV (100 to 200) mV (200 to 300) mV (300 to 400) mV (400 to 500) mV (500 to 600) mV (600 to 700) mV (700 to 1 000) mV (3 to 5) MHz (0 to 100) mV (100 to 200) mV (200 to 300) mV (300 to 400) mV (400 to 800) mV (800 to 1 000) mV 0˚ to 360˚ 50 Hz to 10 MHz (0 to 100) mV (100 to 200) mV (200 to 300) mV (300 to 400) mV (400 to 500) mV (500 to 600) mV (600 to 700) mV (700 to 800) mV (800 to 900) mV (900 to 1000) mV

1.5 × 10-3 1.3 × 10-3 1.2 × 10-3 1.9 × 10-3 1.6 × 10-3 1.5 × 10-3 9.8 × 10-4 6.2 × 10-2 4.4 × 10-2 3.0 × 10-2 2.4 × 10-2 2.2 × 10-2 2.0 × 10-2 3.4 × 10-2 3.1 × 10-2 5.8 × 10-7 3.1 × 10-2 2.2 × 10-2 1.5 × 10-2 1.2 × 10-2 1.1 × 10-2 9.6 × 10-3 0.7˚ 5.8 × 10-5 2.1 × 10-2 1.4 × 10-2 8.3 × 10-3 6.2 × 10-3 4.9 × 10-3 4.0 × 10-3 3.3 × 10-3 2.9 × 10-3 2.6 × 10-3 2.3 × 10-3

Wavetek 9500 Wavetek 9500 Tektronix TSG271 Tektronix 1910 Tektronix TSG271 Tektronix 1910 Tektronix TSG271 Tektronix 1910 Agilent 33250A


Parameter/Equipment


Video Signal Analyzers (cont) –

Vertical Level (Response)

50 kHz to 10 MHz (0 to 100) mV (100 to 200) mV (200 to 300) mV (300 to 400) mV (400 to 500) mV (500 to 600) mV (600 to 700) mV (700 to 800) mV (800 to 900) mV (900 to 1 000) mV

6.6 × 10-2 4.6 × 10-2 3.1 × 10-2 2.5 × 10-2 2.2 × 10-2 2.1 × 10-2 3.4 × 10-2 3.1 × 10-2 2.8 × 10-2 2.7 × 10-2

Agilent 33250A

V. Electrical – RF/Microwave

Parameter/Range


RF Amplifiers –

Gain (0 to 30) dB (30 to 60) dB (60 to 90) dB (0 to 30) dB (30 to 60) dB (60 to 90) dB (0 to 30) dB (30 to 60) dB (60 to 90) dB

Harmonics

(-100 to 0) dBm

5 Hz to 1 GHz (1 to 10) GHz (18 to 40) GHz 9 kHz to 18 GHz

0.08 dB 0.11 dB 0.24 dB 0.08 dB 0.11 dB 0.24 dB 0.15 dB 0.23 dB 0.60 dB 1.5 dB

Agilent E5061B or Agilent N5230C with Agilent 85032F, Keysight 85054D, Agilent 85052D, Maury 85056KE02, Keysight 85056D


Parameter/Range


Coaxial Attenuators – Attenuation

(0 to 10) dB (10 to 20) dB (20 to 30) dB (30 to 40) dB (40 to 50) dB (50 to 60) dB

(0 to 10) dB (10 to 20) dB (20 to 30) dB (30 to 40) dB (40 to 50) dB (50 to 60) dB (60 to 70) dB (70 to 80) dB (80 to 90) dB (90 to 100) dB (100 to 110) dB (110 to 120) dB


5 Hz to 9 kHz 9 kHz to 26.5 GHz (26.5 to 40) GHz

0.11 dB 0.13 dB 0.15 dB 0.17 dB 0.21 dB 0.30 dB 0.04 dB 0.04 dB 0.05 dB 0.05 dB 0.06 dB 0.06 dB 0.07 dB 0.08 dB 0.08 dB 0.09 dB 0.09 dB 0.10 dB 0.21 dB 0.23 dB 0.29 dB 0.30 dB 0.47 dB 1.2 dB

Agilent E5061B or Agilent N5230C with Agilent 85032F, Keysight 85054D, Agilent 85052D, Maury 85056KE02, Keysight 85056D R&S FSMR26

Burst Pulse Generators – Output Voltage @ 50 Ω

10 V (10 to 20) V (20 to 50) V (50 to 200) V (200 to 500) V (0.5 to 1) kV (1 to 2) kV (2 to 2.5) kV (2.5 to 3) kV (3 to 4) kV

0.32 V 3.2 × 10-2 2.6 × 10-2 3.2 × 10-2 2.6 × 10-2 3.2 × 10-2 2.3 × 10-2 1.9 × 10-2 1.6 × 10-2 3.2 × 10-2

Tektronix DPO4102B Haefely PAT 50A


Parameter/Equipment


Burst Pulse Generators –

Output Voltage @ 50 Ω

Output Voltage @ 1 kΩ

-10 V (-10 to -20) V (-20 to -50) V (-50 to -200) V (-200 to -500) V (-0.5 to -1) kV (-1 to -2) kV (-2 to -2.5) kV (-2.5 to -3) kV (-3 to -4) kV 10 V (10 to 40) V (40 to 100) V (100 to 400) V (0.2 to 1) kV (1 to 2) kV (2 to 4) kV (4 to 5) kV (5 to 6) kV (6 to 8) kV -10 V (-10 to -40) V (-40 to -100) V (-100 to -400) V (-0.4 to -1) kV (-1 to -2) kV (-2 to -4) kV (-4 to -5) kV (-5 to -6) kV (-6 to -8) kV

0.32 V 3.2 × 10-2 2.6 × 10-2 3.2 × 10-2 2.6 × 10-2 3.2 × 10-2 2.3 × 10-2 1.9 × 10-2 1.6 × 10-2 3.2 × 10-2 0.24 V 3.1 × 10-2 2.5 × 10-2 3.1 × 10-2 2.5 × 10-2 3.1 × 10-2 2.2 × 10-2 1.8 × 10-2 1.5 × 10-2 1.1 × 10-2 0.24 V 3.1 × 10-2 2.5 × 10-2 3.1 × 10-2 2.5 × 10-2 3.1 × 10-2 2.2 × 10-2 1.8 × 10-2 1.5 × 10-2 1.1 × 10-2



Parameter/Equipment


Burst Pulse Generators –

Delta Time Measurement (Rise/Fall/Duration/Period /Repetition Rate/Burst Duration)

Frequency Measurement

1.0 ns (1.0 to 2.0) ns (2.0 to 5.0) ns (5.0 to 10.0) ns (10 to 20) ns (20 to 100) ns (100 to 200) ns (200 to 500) ns (0.5 to 1.0) μs (1.0 to 2.0) μs (2.0 to 10) μs (10 to 20) μs (20 to 50) μs (50 to 100) μs (100 to 200) μs (200 to 500) μs (0.5 to 1.0) ms (1.0 to 2.0) ms (2.0 to 10) ms (10 to 20) ms (20 to 100) ms (100 to 200) ms (200 to 500) ms (0.5 to 2) s (2.0 to 5.0) s 2.5 kHz (2.5 to 5) kHz (5 to 10) kHz (10 to 100) kHz (0.1 to 1) MHz (1 to 3) MHz (3 to 10) MHz (10 to 30) MHz (30 to 100) MHz

0.02 ns 7.5 × 10-3 3.6 × 10-3 2.7 × 10-3 3.0 × 10-3 2.3 × 10-3 2.9 × 10-3 2.3 × 10-3 2.5 × 10-3 2.9 × 10-4 2.3 × 10-4 2.9 × 10-3 2.3 × 10-3 2.4 × 10-3 2.9 × 10-3 2.4 × 10-3 2.8 × 10-2 3.5 × 10-2 2.3 × 10-3 2.9 × 10-3 2.3 × 10-3 2.9 × 10-3 2.3 × 10-3 3.1 × 10-3 2.3 × 10-3 1.6 Hz 3.2 × 10-4 8.3 × 10-4 5.9 × 10-4 1.2 × 10-3 3.1 × 10-4 6.0 × 10-4 3.5 × 10-4 1.5 × 10-3



Parameter/Equipment


Attenuator Calibrators –Attenuation Measurement Accuracy


0.027 dB 0.029 dB 0.031 dB 0.038 dB 0.042 dB 0.043 dB 0.048 dB 0.053 dB 0.060 dB 0.065 dB 0.069 dB 0.074 dB

HP 8494H, HP 8496H

RF Power Meter Calibrators –Power Range

3 μW 10 μW 30 μW 100 μW 300 μW 1 mW 3 mW 10 mW 30 mW 100 mW

0.27 nW 0.44 nW 1.8 nW 2.9 nW 15 nW 0.02 μW 0.10 μW 0.18 μW 0.45 μW 2.5 μW

HP 3458A

EMC Transducers –

Transfer Impedance

Reflection Coefficient Absorbing Clamps, Insertion Loss

5 Hz to 400 MHz 400 MHz to 3 GHz 5 Hz to 3 GHz 30 MHz to 1 GHz

0.54 dB 1.1 dB 5.9 × 10-3 lin 1.8 dB

CISPR 16-1-2, IEC 61000-4-6; Agilent E5061B with Agilent 85032F CISPR 16-1-3, CISPR 16-1-4; Agilent E5061B with Agilent 85032F


Parameter/Range


Coaxial Directional Couplers/Splitters – Coupling Factor




5 Hz to 9 kHz 9 kHz to 26.5 GHz (26.5 to 40) GHz

0.11 dB 0.13 dB 0.15 dB 0.17 dB 0.21 dB 0.30 dB 0.04 dB 0.04 dB 0.05 dB 0.05 dB 0.06 dB 0.06 dB 0.07 dB 0.08 dB 0.08 dB 0.09 dB 0.09 dB 0.10 dB 0.21 dB 0.23 dB 0.29 dB 0.30 dB 0.47 dB 1.2 dB

Agilent E5061B or Agilent N5230C with Agilent 85032F, Keysight 85054D, Agilent 85052D, Maury 85056KE02, Keysight 85056D R&S FSMR26


Parameter/Equipment


Electrostatic Discharge Generators –

Current (Ip)

T1(30 ns, 65 ns)

(6.7 to7.5) A (7.5 to 15) A (15 to 22.5) A (22.5 to 30) A (30 to 45.0) A (45.0 to 56.3) A (56.3 to 75) A (75 to 93.8) A (93.8 to 150) A -(6.7 to 7.5) A -(7.5 to 15) A -(15 to 22.5) A -(22.5 to 30) A -(30 to 45.0) A -(45.0 to 56.3) A -(56.3 to 75) A -(75 to 93.8) A -(93.8 to 150) A (2 to 4) A (4 to 8) A (8 to 12) A (12 to 16) A (16 to 24) A (24 to 30) A (30 to 40) A (40 to 50) A (50 to 80) A -(2 to 4) A -(4 to 8) A -(8 to 12) A -(12 to 16) A -(16 to 24) A -(24 to 30) A -(30 to 40) A -(40 to 50) A -(50 to 80) A

0.24 A 0.33 A 0.63 A 0.73 A 1.3 A 1.6 A 1.9 A 2.2 A 3.1 A 0.24 A 0.33 A 0.63 A 0.73 A 1.3 A 1.6 A 1.9 A 2.2 A 3.1 A 0.21 A 0.24 A 0.53 A 0.56 A 1.1 A 1.2 A 1.3 A 1.5 A 2.3 A 0.21 A 0.24 A 0.53 A 0.56 A 1.1 A 1.2 A 1.3 A 1.5 A 2.3 A

Tektronix TDS694C MWF MESD-T04G Tektronix TDS694C MWF MESD-T04G


Parameter/Equipment


Electrostatic Discharge Generators (cont) –

T2(60 ns, 130 ns) T3(180 ns, 400 ns)

(1 to 2) A (2 to 4) A (4 to 6) A (6 to 8) A (8 to 12) A (12 to 15) A (15 to 20) A (20 to 25) A (25 to 40) A -(1 to 2) A -(2 to 4) A -(4 to 6) A -(6 to 8) A -(8 to 12) A -(12 to 15) A -(15 to 20) A -(20 to 25) A -(25 to 40) A (0.30 to 0.55) A (0.55 to 1.10) A (1.10 to 1.65) A (1.65 to 2.20) A (2.20 to 3.30) A (3.30 to 4.13) A (4.13 to 5.50) A (5.50 to 6.88) A (6.88 to 10.6) A -(0.30 to 0.55) A -(0.55 to 1.10) A -(1.10 to 1.65) A -(1.65 to 2.20) A -(2.20 to 3.30) A -(3.30 to 4.13) A -(4.13 to 5.50) A -(5.50 to 6.88) A -(6.88 to 10.6) A

0.20 A 0.21 A 0.50 A 0.50 A 1.0 A 1.0 A 1.1 A 1.1 A 2.0 A 0.20 A 0.21 A 0.50 A 0.50 A 1.0 A 1.0 A 1.1 A 1.1 A 2.0 A 35 mA 39 mA 93 mA 0.10 A 0.30 A 0.29 A 0.30 A 0.31 A 0.39 A 35 mA 39 mA 93 mA 0.10 A 0.30 A 0.29 A 0.30 A 0.31 A 0.39 A

Tektronix TDS694C MWF MESD-T04G Tektronix TDS694C MWF MESD-T04G


Parameter/Equipment



T4(360 ns, 800 ns) Rise/Fall Time Voltage

(0.10 to 0.30) A (0.30 to 0.60) A (0.60 to 0.90) A (0.90 to 1.20) A (1.20 to 1.80) A (1.80 to 2.25) A (2.25 to 3.00) A (3.00 to 3.75) A (3.75 to 5.90) A -(0.10 to 0.30) A -(0.30 to 0.60) A -(0.60 to 0.90) A -(0.90 to 1.20) A -(1.20 to 1.80) A -(1.80 to 2.25) A -(2.25 to 3.00) A -(3.00 to 3.75) A -(3.75 to 5.90) A (0.5 to 1) ns (0.1 to 0.5) kV (0.5 to 1) kV (1 to 2) kV (2 to 4) kV (4 to 6) kV (6 to 8) kV (8 to 10) kV (10 to 12) kV (12 to 14) kV (14 to 16) kV (16 to 18) kV (18 to 20) kV (20 to 25) kV (25 to 30) kV

34 mA 35 mA 90 mA 91 mA 0.29 A 0.28 A 0.28 A 0.29 A 0.36 A 34 mA 35 mA 90 mA 91 mA 0.29 A 0.28 A 0.28 A 0.29 A 0.36 A 37 ps 7.6 V 9.0 V 48 V 49 V 67 V 68 V 78 V 97 V 0.12 V 0.12 V 0.13 V 0.14 V 0.20 V 0.20 V

Tektronix TDS694C MWF MESD-T04G Tektronix TDS694C MWF MESD-T04G Brandenburg 149-04


Parameter/Equipment



Voltage

Semiconductor ESD Peak Current (MM or HBM) ESD Rise/Fall Time of Semiconductor ESD Decay Time of Semiconductor

-(0.1 to 0.5) kV -(0.5 to 1) kV -(1 to 2) kV -(2 to 4) kV -(4 to 6) kV -(6 to 8) kV -(8 to 10) kV -(10 to 12) kV -(12 to 14) kV -(14 to 16) kV -(16 to 18) kV -(18 to 20) kV -(20 to 25) kV -(25 to 30) kV (0.15 to 0.17) A (0.17 to 0.33) A (0.33 to 0.67) A (0.67 to 1.33) A (1.33 to 2.67) A (2.67 to 5.33) A (5.33 to 14) A -(0.15 to 0.17) A -(0.17 to 0.33) A -(0.33 to 0.67) A -(0.67 to 1.33) A -(1.33 to 2.67) A -(2.67 to 5.33) A -(5.33 to 14) A (1 to 11) ns (100 to 200) ns

7.6 V 9.0 V 48 V 49 V 67 V 68 V 78 V 97 V 0.12 V 0.12 V 0.13 V 0.14 V 0.20 V 0.20 V 11 mA 18 mA 36 mA 71 mA 0.14 A 0.28 A 0.49 A 11 mA 18 mA 36 mA 71 mA 0.14 A 0.28 A 0.49 A 12 ps 0.58 ns

Tektronix TDS694C MWF MESD-T04G Brandenburg 149-04 Tektronix TDS694C Tektronix CT-1/P6041 Weinschel 24-20-34-LIM Weinschel 24-40-34-LIM


Parameter/Equipment



ESD Peak Voltage of Semiconductor

(0.01 to 0.1) kV (0.1 to 0.2) kV (0.2 to 0.25) kV (0.25 to 0.4) kV (0.4 to 0.5) kV (0.5 to 0.8) kV (0.8 to 1) kV (1 to 2) kV (2 to 4) kV (4 to 8) kV -(0.01 to 0.1) kV -(0.1 to 0.2) kV -(0.2 to 0.25) kV -(0.25 to 0.4) kV -(0.4 to 0.5) kV -(0.5 to 0.8) kV -(0.8 to 1) kV -(1 to 2) kV -(2 to 4) kV -(4 to 8) kV

3.7 V 9.1 V 10 V 15 V 18 V 67 V 70 V 92 V 0.16 kV 0.31 kV 3.7 V 9.1 V 10 V 15 V 18 V 67 V 70 V 92 V 0.16 kV 0.31 kV

Tektronix TDS694C Tektronix P6015A

EMC Receivers –

Reference Frequency

Input Impedance (Reflection Coefficient)

Sine-Wave Voltage Accuracy

Pulse Response

Pulse Repetition Frequency Response

80 kHz to 100 MHz 9 kHz to 1 GHz (1 to 3) GHz (3 to 20) GHz (20 to 40) GHz (40 to 50) GHz 10 Hz to 2 GHz (2 to 12) GHz (12 to 40) GHz (40 to 50) GHz 9 kHz to 40 GHz 9 kHz to 1 GHz

5.8 × 10-11 Hz 3.8 × 10-3 lin 5.3 × 10-2 lin 9.3 × 10-3 lin 1.2 × 10-2 lin 5.9 × 10-2 lin 0.04 dB 0.06 dB 0.08 dB 0.25 dB 0.25 dB 0.10 dB

CISPR 16-1-1, ANSI C63.2; Schwarzbeck IGUU 2918


Parameter/Equipment


EMC Receivers (cont) –

Overall Selectivity

IF Rejection Ratio

Image Frequency Rejection Ratio

Other Spurious Response

Random Noise

Resolution Bandwidth

9 kHz to 40 GHz 9 kHz to 40 GHz 9 kHz to 40 GHz 9 kHz to 40 GHz 9 kHz to 40 GHz 10 Hz to 20 MHz

0.08 dB 0.31 dB 0.31 dB 0.31 dB 0.07 dB 7.4 × 10-4

CISPR 16-1-1, ANSI C63.2; Schwarzbeck IGUU 2918

RF Filters –

Cutoff Frequency

Insertion Loss:

(0 to 10) dB (10 to 20) dB (20 to 30) dB (30 to 40) dB (40 to 50) dB (50 to 60) dB (60 to 70) dB (70 to 80) dB (80 to 100) dB

(0 to 10) dB (10 to 20) dB (20 to 30) dB (30 to 40) dB (40 to 50) dB (50 to 60) dB (60 to 70) dB (70 to 80) dB (80 to 100) dB

9 kHz to 26.5 GHz

9 kHz to 1 GHz

(1 to 18) GHz

6.4 × 10-7 0.11 dB 0.12 dB 0.14 dB 0.17 dB 0.21 dB 0.30 dB 0.54 dB 1.3 dB 3.2 dB 0.11 dB 0.12 dB 0.13 dB 0.15 dB 0.20 dB 0.34 dB 0.72 dB 1.8 dB 4.7 dB



Parameter/Equipment


RF Filters (cont) –

Insertion Loss:

(0 to 10) dB (10 to 20) dB (20 to 30) dB (30 to 40) dB (40 to 50) dB (50 to 60) dB (60 to 70) dB (70 to 80) dB (80 to 100) dB (0 to 10) dB (10 to 20) dB (20 to 30) dB (30 to 40) dB (40 to 50) dB (50 to 60) dB (60 to 70) dB

(18 to 26.5) GHz

(26.5 to 40) GHz

0.21 dB 0.23 dB 0.24 dB 0.27 dB 0.35 dB 0.59 dB 1.3 dB 3.2 dB 7.6 dB 0.21 dB 0.23 dB 0.24 dB 0.29 dB 0.47 dB 1.1 dB 3.0 dB


RF impedance meters –

Output frequency Output level

1 mHz to 18 GHz 9 kHz to 18 GHz (0 to 20) dBm (-10 to 0) dBm (-30 to -10) dBm (-50 to -30) dBm (-70 to -50) dBm (-90 to -70) dBm (-110 to -90) dBm (-120 to -110) dBm

5.8 × 10-11 0.19 dB 0.18 dB 0.19 dB 0.20 dB 0.21 dB 0.22 dB 0.23 dB 0.24 dB

SRS FS725, Keysight 53210A, Agilent E9304A-H18, R&S FSMR

RF impulse generators –

Impulse Level

9 kHz to 1 GHz

0.28 dB

Schwarzbeck IGUU2918, R&S ESU26


Parameter/Equipment


LISNs –

Impedance Phase Angle Voltage Division Factor

Isolation

(0 to 50) dB (0 to 60) dB (0 to 70) dB (0 to 80) dB (0 to 90) dB

5 Hz to 1 GHz 5 Hz to 1 GHz 5 Hz to 1 GHz 9 kHz to 200 MHz

2.0 × 10-2 lin 0.02° 0.12 dB 0.2 dB 0.3 dB 0.5 dB 1.2 dB 3.1 dB

ANSI C63.4, CISPR 25, CISPR 16-1-2, MIL-STD-461F, ISO 7637-2; Agilent E5061B, Keysight 85032F

CDNs –

Impedance Phase Angle Voltage Division Factor

5 Hz to 1 GHz 5 Hz to 1 GHz 5 Hz to 1 GHz

2.0 × 10-2 lin 0.02° 0.12 dB

IEC 61000-4-6, CISPR 16-1-2; Agilent E5061B, Keysight 85032F

ISNs –

Impedance Phase Angle Voltage Division Factor Longitudinal Conversion Loss

9 kHz to 1 GHz 9 kHz to 1 GHz 9 kHz to 1 GHz 9 kHz to 1 GHz

2.0 × 10-2 lin 0.02° 0.12 dB 0.27 dB

CISPR 22, CISPR 32, CISPR 16-1-2; Agilent E5061B, Keysight 85032F

EM Clamps –

Coupling Factor Decoupling Factor Impedance

9 kHz to 1 GHz 9 kHz to 1 GHz 9 kHz to 1 GHz

0.30 dB 0.30 dB 1.8 × 10-2 lin

IEC 61000-4-6; Agilent E5061B, Keysight 85032F

Impedance converters –

Impedance Phase Angle Attenuation

5 Hz to 3 GHz 5 Hz to 3 GHz 5 Hz to 3 GHz

6.0 × 10-3 lin 0.011° 0.13 dB

Agilent E5061B, Keysight 85032F


Parameter/Equipment


Coaxial Standard Mismatches –Reflection coefficients

9 kHz to 1 GHz (1 to 18) GHz

4.8 × 10-3 lin 1.0 × 10-2 lin


Mobile Communication Test Sets –

Output Frequency

Output Level (-30 to 20) dBm

Absolute TRFL Accuracy

(0 to 30) dBm (-40 to 0) dBm (-80 to -40) dBm (-120 to -80) dBm (-140 to -120) dBm



1 mHz to 46 GHz 9 kHz to 100 MHz 100 MHz to 1 GHz (1 to 8) GHz (8 to 12) GHz (12 to 26) GHz (26 to 40) GHz (40 to 50) GHz 9 kHz to 8 GHz (8 to 18) GHz (18 to 26.5) GHz

5.8 × 10-11 0.05 dB 0.07 dB 0.08 dB 0.09 dB 0.12 dB 0.15 dB 0.21 dB 0.15 dB 0.16 dB 0.18 dB 0.20 dB 0.21 dB 0.20 dB 0.20 dB 0.22 dB 0.24 dB 0.25 dB 0.27 dB 0.27 dB 0.29 dB 0.31 dB 0.32 dB

SRS FS725, Keysight 53210A, R&S FSMR, R&S NRP-Z37, Keysight N5173B, Agilent E9304A-H18


Parameter/Equipment


Mobile Communication Test Sets (cont) –

Relative TRFL Accuracy



Output Amplitude Modulation Output Frequency Modulation

Output Phase Modulation Output Modulation Distortion Output Harmonics

Output AC Voltage 10 Hz to 25 kHz

Output DC Voltage Input Frequency Input Level

(-120 to 20) dBm

9 kHz to 18 GHz (18 to 26.5) GHz 100 kHz to 26.5 GHz 100 kHz to 26.5 GHz 100 kHz to 26.5 GHz 100 kHz to 26.5 GHz 9 kHz to 10 GHz (10 to 26.5) GHz 100 mV to 100 V 100 mV to 100 V 1 mHz to 18 GHz 9 kHz to 100 MHz 100 MHz to 1 GHz (1 to 8) GHz (8 to 12) GHz (12 to 18) GHz (18 to 50) GHz

0.05 dB 0.05 dB 0.08 dB 0.09 dB 0.10 dB 0.05 dB 0.05 dB 0.08 dB 0.09 dB 0.11 dB 1.2 × 10-2 1.2 × 10-2 1.2 × 10-2 3.0 × 10-2 1.4 dB 1.7 dB 4.0 × 10-4 5.9 × 10-5 5.8 × 10-11 0.05 dB 0.07 dB 0.08 dB 0.09 dB 0.12 dB 0.12 dB



Parameter/Equipment


Mobile Communication Test Sets (cont) –

Output Level Linearity

(-10 to 30) dBm (-20 to -10) dBm (-30 to -20) dBm (-40 to -30) dBm (-50 to -40) dBm (-60 to -50) dBm (-70 to -60) dBm (-80 to -70) dBm (-90 to -80) dBm (-100 to -90) dBm (-110 to -100) dBm (-140 to -110) dBm

Input Amplitude Modulation Input Frequency Modulation Input Phase Modulation Input Modulation Distortion Input Harmonics Input AC Voltage

10 Hz to 25 kHz Input DC Voltage

9 kHz to 26.5 GHz 100 kHz to 26.5 GHz 100 kHz to 26.5 GHz 100 kHz to 26.5 GHz 100 kHz to 26.5 GHz 9 kHz to 10 GHz (10 to 18) GHz 100 mV to 100 V 100 mV to 100 V

0.034 dB 0.040 dB 0.046 dB 0.052 dB 0.058 dB 0.064 dB 0.070 dB 0.076 dB 0.080 dB 0.086 dB 0.092 dB 0.098 dB 1.2 × 10-2 1.2 × 10-2 1.2 × 10-2 3.0 × 10-2 1.4 dB 1.7 dB 4.0 × 10-4 5.9 × 10-5



Parameter/Equipment


Modulation Meters –

Frequency Amplitude Modulation Frequency Modulation Phase Modulation Audio RMS Accuracy Reference Power Zero Set Range-to-Range Error Tuned RF Level

1 mHz to 26.5 GHz 100 kHz to 26.5 GHz 100 kHz to 26.5 GHz 100 kHz to 26.5 GHz 20 Hz to 50 kHz 100 mW to 5 V 50 MHz 1 mW 0.000 μW 0.00 μW 0.0 μW 0.000 mW 0.00 mW 10 μW to 100 mW (0 to 10) dB (10 to 20) dB (20 to 30) dB (30 to 40) dB (40 to 50) dB (50 to 60) dB (60 to 70) dB (70 to 80) dB (80 to 90) dB (90 to 100) dB (100 to 110) dB (110 to 120) dB

5.8 × 10-11 1.2 × 10-2 1.2 × 10-2 1.2 × 10-2 7.0 × 10-4 3.0 × 10-3 0.001 μW 0.01 μW 0.1 μW 0.001 mW 0.01 mW 1.3 × 10-3 0.027 dB 0.029 dB 0.032 dB 0.038 dB 0.043 dB 0.043 dB 0.048 dB 0.054 dB 0.060 dB 0.066 dB 0.069 dB 0.074 dB



Parameter/Range


Network Analyzers –

Output Frequency Output Level Accuracy

(-30 to 20) dBm


(0 to 30) dBm (-40 to 0) dBm (-80 to -40) dBm (-120 to -80) dBm (-140 to -120) dBm (0 to 30) dBm (-40 to 0) dBm (-80 to -40) dBm (-120 to -80) dBm (-140 to -120) dBm

(0 to 30) dBm (-40 to 0) dBm (-80 to -40) dBm (-120 to -80) dBm (-140 to -120) dBm (-30 to 20) dBm (-30 to 20) dBm

1 mHz to 46 GHz 5 Hz to 100 MHz 100 MHz to 1 GHz (1 to 8) GHz (8 to 12) GHz (12 to 18) GHz (18 to 26) GHz (26 to 33) GHz (33 to 40) GHz (40 to 50) GHz (50 to 75) GHz (75 to 110) GHz 9 kHz to 8 GHz (8 to 18) GHz (18 to 26.5) GHz (26.5 to 40) GHz (40 to 50) GHz

5.8 × 10-11 0.05 dB 0.07 dB 0.08 dB 0.09 dB 0.12 dB 0.11 dB 0.13 dB 0.14 dB 0.16 dB 0.21 dB 0.28 dB 0.15 dB 0.16 dB 0.18 dB 0.20 dB 0.21 dB 0.20 dB 0.20 dB 0.22 dB 0.24 dB 0.25 dB 0.27 dB 0.27 dB 0.29 dB 0.31 dB 0.32 dB 0.14 dB 0.21 dB

SRS FS725, Keysight 53210A, R&S FSMR, R&S NRP-Z37, Keysight N5173B, Agilent E9304A-H18, Agilent 8487A, Keysight V8486A, Keysight W8486A, HP 8494H, HP 8496H, Agilent 85032F, Keysight 85054D, Agilent 85052D, Maury 85056KE02, Keysight 85056D


Parameter/Range


Network Analyzers (cont) –

Output Level Linearity

(-10 to 0) dBm (-20 to -10) dBm (-30 to -20) dBm (-40 to -30) dBm (-50 to -40) dBm (-60 to -50) dBm (-70 to -60) dBm (-80 to -70) dBm (-90 to -80) dBm (-100 to -90) dBm (-110 to -100) dBm (-120 to -110) dBm (-30 to 20) dBm (-30 to 20) dBm

Harmonics

Magnitude Dynamic Accuracy

Mismatch Measurement Accuracy Input Impedance

9 kHz to 26.5 GHz (26.5 to 40) GHz (40 to 50) GHz 20 Hz to 20 GHz (20 to 40) GHz (0 to 120) dB 9 kHz to 1 GHz (1 to 18) GHz 9 kHz to 1 GHz (1 to 18) GHz

0.034 dB 0.040 dB 0.046 dB 0.052 dB 0.058 dB 0.064 dB 0.070 dB 0.076 dB 0.080 dB 0.086 dB 0.092 dB 0.098 dB 0.024 dB 0.050 dB 1.4 dB 1.7 dB 0.028 dB 4.8 × 10-3 lin 1.0 × 10-2 lin 4.8 × 10-3 lin 1.0 × 10-2 lin

SRS FS725, Keysight 53210A, R&S FSMR, R&S NRP-Z37, Keysight N5173B, Agilent E9304A-H18, Agilent 8487A, Keysight V8486A, Keysight W8486A, HP 8494H, HP 8496H, Agilent 85032F, Keysight 85054D, Agilent 85052D, Maury 85056KE02, Keysight 85056D

Noise Figure Meters –

Output Frequency Input Impedance Output DC Voltage Noise Figure

1 mHz to 18 GHz 9 kHz to 1 GHz (1 to 3) GHz (3 to 18) GHz 0 V (0.1 to 30) V 10 MHz to 18 GHz

5.8 × 10-11 0.9 × 10-2 lin 1.2 × 10-2 lin 1.9 × 10-2 lin 10 μV 1.1 × 10-6 0.35 dB

SRS FS725, Keysight 53210A, Keysight N5173B, HP 346B


Parameter/Equipment


Noise Generators –


(-120 to 30) dBm

1 mHz to 18 GHz 9 kHz to 3 GHz (3 to 6.6) GHz (6.6 to 18) GHz

5.8 × 10-11 0.51 dB 1.8 dB 2.4 dB

Agilent E4440A

Noise Impulse Simulators – Output Voltage

10 V (10 to 20) V (20 to 50) V (50 to 200) V (200 to 500) V (500 to 1000) V (1 to 2) kV (2 to 4) kV -10 V (-10 to -20) V (-20 to -50) V (-50 to -200) V (-200 to -500) V (-500 to -1000) V (-1 to -2) kV (-2 to -4) kV

0.32 V 3.2 × 10-2 2.6 × 10-2 3.2 × 10-2 2.6 × 10-2 3.2 × 10-2 2.3 × 10-2 1.2 × 10-2 0.32 V 3.2 × 10-2 2.6 × 10-2 3.2 × 10-2 2.6 × 10-2 3.2 × 10-2 2.3 × 10-2 1.2 × 10-2


Noise Impulse Simulators –

Delta Time Measurement (Rise/Fall/Duration/Period/ Repetition Rate/Burst Duration)

0.1 ns (0.1 to 1) ns (1 to 2) ns (2 to 5) ns (5 to 10) ns (10 to 20) ns (20 to 100) ns (100 to 200) ns (200 to 500) ns

0.015 ns 1.5 × 10-2 7.5 × 10-3 3.6 × 10-3 2.7 × 10-3 3.0 × 10-3 2.3 × 10-3 2.9 × 10-3 2.3 × 10-3



Parameter/Equipment


Noise Impulse Simulators (cont) –


(0.5 to 1) μs (1 to 2) μs (2 to 10) μs (10 to 20) μs (20 to 50) μs (50 to 100) μs (100 to 200) μs (200 to 500) μs (0.5 to 1) ms (1 to 2) ms (2 to 10) ms (10 to 20) ms (20 to 100) ms (100 to 200) ms (200 to 500) ms (0.5 to 2) s (2 to 5) s

2.5 × 10-3 2.9 × 10-3 2.3 × 10-3 2.9 × 10-3 2.3 × 10-3 2.4 × 10-3 2.9 × 10-3 2.4 × 10-3 2.8 × 10-2 3.5 × 10-2 2.3 × 10-3 2.9 × 10-3 2.3 × 10-3 2.9 × 10-3 2.3 × 10-3 3.1 × 10-3 2.3 × 10-3


RF power Meters –

Output Frequency Output Level Instrument Accuracy Input Level Accuracy

(-80 to 20) dBm

Input Voltage

1 mHz to 18 GHz (10 to 300) MHz 1 μW to 100 mW 3 μW to 100 mW 9 kHz to 18 GHz (0 to 400) V

5.8 × 10-11 5.6 × 10-3 1.3 × 10-3 0.15 dB 5.8 × 10-5

HP 11683A, R&S NRP-Z51, R&S NRP-Z55, Agilent 8487A, R&S FSMR, R&S NRP-Z37

RF High Power Meters – Calibration Factor

10 kHz to 220 MHz 0.01 W to 2.5 kW 200 MHz to 1 GHz (0.01 to 100) W (1 to 4.2) GHz (0.01 to 10) W

1.9 × 10-2 3.1 × 10-2 3.4 × 10-2

Bird 6091


Parameter/Range


Diode Power Aensors –

Calibration Factor

1 μW to 100 mW Reflection Coefficient

9 kHz to 1 GHz (1 to 10) GHz (10 to 18) GHz (18 to 26) GHz (26 to 34) GHz (34 to 38) GHz (38 to 43) GHz (43 to 50) GHz 9 kHz to 1 GHz (1 to 3) GHz (3 to 20) GHz (20 to 40) GHz (40 to 50) GHz

1.4 % 1.6 % 2.1 % 2.4 % 2.8 % 3.1 % 3.6 % 5.1 % 3.8 × 10-3 lin 5.3 × 10-3 lin 9.3 × 10-3 lin 1.2 × 10-2 lin 5.9 × 10-2 lin

HP 8487B Thermistor Mount, R&S NRP-Z51, R&S NRP-Z55, Agilent 8487A Agilent E5061B or Agilent N5230C with Agilent 85032F, Keysight 85054D, Agilent 85052D, Maury 85056KE02, Keysight 85056D

Thermocouple Power Sensors –

Calibration Factor

1 μW to 100 mW

Reflection Coefficient

(0 to 1)

9 kHz to 1 GHz 1 GHz to 10 GHz 10 GHz to 18 GHz 18 GHz to 26 GHz 26 GHz to 34 GHz 34 GHz to 38 GHz 38 GHz to 43 GHz 43 GHz to 50 GHz 9 kHz to 1 GHz 1 GHz to 3 GHz 3 GHz to 20 GHz 20 GHz to 40 GHz 40 GHz to 50 GHz

1.4 % 1.6 % 2.1 % 2.4 % 2.8 % 3.1 % 3.6 % 5.1 % 3.8 × 10-3 lin 5.3 × 10-3 lin 9.3 × 10-3 lin 1.2 × 10-2 lin 5.9 × 10-2 lin

HP 8487B Thermistor Mount, R&S NRP-Z51, R&S NRP-Z55, Agilent 8487A


Parameter/Equipment


Pulse Generators –

Frequency Period Delay Double Pulse Width Transition Time DC Level Output Level (10 mV) (10 mV to 100 mV) (100 mV to 1 V) (1 to 10) V (10 to 100) V (100 to 300) V

1 Hz to 10 GHz 300 ps to 1 s 1 s to 100 ns (100 to 10) ns (10 to 1) ns 1 s to 100 ns (100 to 10) ns (10 to 1) ns 1 s to 100 ns (100 to 10) ns (10 to 1) ns 1 s to 100 ns (100 to 10) ns (10 to 1) ns 10 mV to 100 V 20 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz 20 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz 20 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz 20 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz 20 Hz to 1 kHz (1 to 20) kHz (20 to 100) kHz 20 Hz to 1 kHz

6.1 × 10-9 6.1 × 10-9 1.2 × 10-3 1.3 × 10-3 5.9 × 10-3 1.2 × 10-3 1.3 × 10-3 5.9 × 10-3 1.2 × 10-3 1.3 × 10-3 5.9 × 10-3 1.2 × 10-3 1.3 × 10-3 5.9 × 10-3 6.1 × 10-4 9.4 μV 14 μV 16 μV 6.4 × 10-4 7.6 × 10-4 1.1 × 10-3 6.3 × 10-4 6.7 × 10-4 6.7 × 10-4 6.3 × 10-4 6.7 × 10-4 6.7 × 10-4 6.3 × 10-4 6.7 × 10-4 6.7 ×10-4 3.1 × 10-4

Fluke 8508A Odetics 425-311 H.P 53132A H.P 53152A Tektronix TDS5104 Tektronix TDS694C


Parameter/Equipment


Radar Test Sets –

Output frequency Output level


Harmonics Output Modulation Signal Level Amplitude Modulation Frequency Modulation Modulation Distortion Phase DDM SDM VOR Pulse Width Input Frequency Input Level

1 mW to 100 W

1 mHz to 18 GHz 9 kHz to 18 GHz 9 kHz to 5 GHz (5 to 18) GHz 9 kHz to 18 GHz 9 kHz to 18 GHz 9 kHz to 18 GHz 9 kHz to 18 GHz 9 kHz to 18 GHz (0.1 to 1360) MHz (0.1 to 1360) MHz (0.1 to 1360) MHz 1 ns to 10 ms 9 kHz to 18 GHz (0.1 to 1360) MHz

5.8 × 10-11 0.12 dB 0.12 dB 0.13 dB 0.15 dB 0.30 dB 1.2 dB 1.5 dB 1.3 dB 1.7 × 10-2 1.2 × 10-2 1.2 × 10-2 1.2 × 10-2 3.0 × 10-2 3.0 × 10-2 3.0 × 10-2 2.3 × 10-2 5.8 × 10-10 1.9 × 10-2

SRS FS725, Keysight 53210A, R&S FSMR, R&S NRP-Z37, Keysight N5173B, Agilent E9304A-H18, R&S FMAV


Parameter/Range


RF Signal Generators –

Output Frequency Absolute Output Level

(-30 to 20) dBm


(0 to 30) dBm (-40 to 0) dBm (-80 to -40) dBm (-120 to -80) dBm (-140 to -120) dBm (0 to 30) dBm (-40 to 0) dBm (-80 to -40) dBm (-120 to -80) dBm (-140 to -120) dBm


Relative TRFL Accuracy


1 mHz to 46 GHz 5 Hz to 100 MHz 100 MHz to 1 GHz (1 to 8) GHz (8 to 12) GHz (12 to 18) GHz (18 to 26) GHz (26 to 33) GHz (33 to 40) GHz (40 to 50) GHz (50 to 75) GHz (75 to 110) GHz 9 kHz to 8 GHz (8 to 18) GHz (18 to 26.5) GHz 9 kHz to 26.5 GHz

5.8 × 10-11 0.05 dB 0.07 dB 0.08 dB 0.09 dB 0.12 dB 0.11 dB 0.13 dB 0.14 dB 0.16 dB 0.21 dB 0.28 dB 0.15 dB 0.16 dB 0.18 dB 0.20 dB 0.21 dB 0.20 dB 0.20 dB 0.22 dB 0.24 dB 0.25 dB 0.27 dB 0.27 dB 0.29 dB 0.31 dB 0.32 dB 0.05 dB 0.05 dB 0.08 dB 0.09 dB 0.11 dB

SRS FS725, Keysight 53210A, R&S FSMR, R&S NRP-Z37, Keysight N5173B, Agilent E9304A-H18, Agilent 8487A, Keysight V8486A


Parameter/Equipment


RF Signal Generators (cont) –

Output Amplitude Modulation Output Frequency Modulation Output Phase Modulation Output Modulation Distortion Harmonics Pulse Modulation

100 kHz to 26.5 GHz 100 kHz to 26.5 GHz 100 kHz to 26.5 GHz 100 kHz to 26.5 GHz 20 Hz to 20 GHz (20 to 40) GHz 1 μs to 1 s

1.2 × 10-2 1.2 × 10-2 1.2 × 10-2 3.0 × 10-2 1.4 dB 1.7 dB 1.2 × 10-3

SRS FS725, Keysight 53210A, R&S FSMR, R&S NRP-Z37, Keysight N5173B, Agilent E9304A-H18, Agilent 8487A, Keysight V8486A

RF Spectrum Analyzers –

Reference Frequency Reference Level

(-30 to 10) dBm Frequency Readout Marker Frequency Counter Frequency Span Resolution Bandwidth Resolution Bandwidth Selectivity Resolution Bandwidth Switching Error Input Attenuator Accuracy Scale Fidelity

10 MHz to 1 GHz 10 MHz to 1 GHz 5 Hz to 110 GHz 5 Hz to 110 GHz 5 Hz to 110 GHz 1 Hz to 100 MHz 1 Hz to 100 MHz 1 Hz to 100 MHz (0 to 100) dB (0 to 100) dB

5.8 × 10-11 0.07 dB 9.6 × 10-4·SPAN 0.1 Hz 1.4 × 10-3·SPAN 2.2 × 10-3·RBW 4.0 × 10-3·RBW 0.004 dB 0.08 dB 0.08 dB

SRS FS725, Keysight 53210A, R&S NRP-Z55, Agilent E9304A-H18, Agilent 8487A, Keysight V8486A, Keysight W8486A, Agilent 33250A, HP 83650B, OML S19MS-A, S12MS-A, S08MS-A, HP 8494H, HP 8496H


Parameter/Equipment


RF Spectrum Analyzers –

Reference Level Accuracy Frequency Response Average Noise Level Noise Side Band Input Level

(-60 to 30) dB

Conversion Factor

(0 to 100) dB 5 Hz to 4 GHz (4 to 18) GHz (18 to 26.5) GHz (26.5 to 40) GHz (40 to 110) GHz 5 Hz to 3 GHz (3 to 12) GHz (12 to 18) GHz (18 to 40) GHz (40 to 50) GHz (-30 to 30) kHz (1 to 100) kHz (18 to 110) GHz

0.06 dB 0.09 dB 0.15 dB 0.19 dB 0.21 dB 0.35 dB 0.58 dB 1.0 dB 1.4 dB 1.7 dB 2.0 dB 1.7 dB 0.18 dB 0.82 dB

SRS FS725, Keysight 53210A, R&S NRP-Z55, Agilent E9304A-H18, Agilent 8487A, Keysight V8486A, Keysight W8486A, Agilent 33250A, HP 83650B, OML S19MS-A, S12MS-A, S08MS-A, HP 8494H, HP 8496H

RF Speed Guns – Speed

(5 to 2 000) m/s

0.03 m/s

Agilent E4440A Agilent 33250A H.P 53152A

Surge Generators –

Voltage Output

0 V (0 to 10) V (10 to 20) V (20 to 50) V (50 to 100) V (100 to 200) V (200 to 500) V (500 to 1000) V (1 to 2) kV (2 to 4) kV (4 to 6) kV (6 to 8) kV (8 to 10) kV (10 to 15) kV (15 to 18) kV (18 to 20) kV

0.20 V 3.6 × 10-2 5.0 × 10-2 3.9 × 10-2 4.0 × 10-2 5.0 × 10-2 4.1 × 10-2 4.0 × 10-2 5.0 × 10-2 2.5 × 10-2 2.0 × 10-2 1.6 × 10-2 1.4 × 10-2 1.1 × 10-2 9.6 × 10-3 8.6 × 10-3

Tektronix DPO4102B Tektronix P6015A


Parameter/Equipment


Surge Generators (cont) –

Voltage Output

Current Output

0 V (-0 to -10) V (-10 to -20) V (-20 to -50) V (-50 to -100) V (-100 to -200) V (-200 to -500) V (-500 to -1000) V (-1 to -2) kV (-2 to -4) kV (-4 to -6) kV (-6 to -8) kV (-8 to -10) kV (-10 to -15) kV (-15 to -18) kV (-18 to -20) kV 0 A (0 to 1) A (1 to 2) A (2 to 5) A (5 to 10) A (10 to 20) A (20 to 50) A (50 to 100) A (100 to 500) A (500 to 1000) A (1000 to 2000) A (2000 to 3000) A -0 A (-0 to -1) A (-1 to -2) A (-2 to -5) A (-5 to -10) A (-10 to -20) A (-20 to -50) A (-50 to -100) A (-100 to -500) A (-500 to -1000) A (-1000 to -2000) A (-2000 to -3000) A

0.20 V 3.6 × 10-2 5.0 × 10-2 3.9 × 10-2 4.0 × 10-2 5.0 × 10-2 4.1 × 10-2 4.0 × 10-2 5.0 × 10-2 2.5 × 10-2 2.0 × 10-2 1.6 × 10-2 1.4 × 10-2 1.1 × 10-2 9.6 × 10-3 8.6 × 10-3 38 mA 3.8 × 10-2 4.0 × 10-2 5.7 × 10-3 5.1 × 10-3 5.3 × 10-3 5.2 × 10-3 4.9 × 10-3 5.2 × 10-3 5.1 × 10-3 5.4 × 10-3 9.0 × 10-3

38 mA 3.8 × 10-2 4.0 × 10-2 5.7 × 10-3 5.1 × 10-3 5.3 × 10-3 5.2 × 10-3 4.9 × 10-3 5.2 × 10-3 5.1 × 10-3 5.4 × 10-3 9.0 × 10-3

Tektronix DPO4102B Tektronix P6015A Tektronix DPO4102B Pearson 110 Weinschel 20dB Weinschel 40dB


Parameter/Equipment


Surge Generators (cont) –


Frequency

0.1 ns (0.1 to 1) ns (1 to 2) ns (2 to 5) ns (5 to 10) ns (10 to 20) ns (20 to 100) ns (100 to 200) ns (200 to 500) ns (0.5 to 1) μs (1 to 2) μs (2 to 10) μs (10 to 20) μs (20 to 50) μs (50 to 100) μs (100 to 200) μs (200 to 500) μs (0.5 to 1) ms (1 to 2) ms (2 to 10) ms (10 to 20) ms (20 to 100) ms (100 to 200) ms (200 to 500) ms (0.5 to 2) s (2 to 5) s 1 Hz (1 to 10) Hz (10 to 100) Hz (0.1 to 1) kHz (1 to 10) kHz (10 to 100) kHz (0.1 to 1) MHz (1 to 10) MHz

0.015 ns 1.5 × 10-2 7.5 × 10-3 3.6 × 10-3 2.7 × 10-3 3.0 × 10-3 2.3 × 10-3 2.9 × 10-3 2.3 × 10-3 2.5 × 10-3 2.9 × 10-3 2.3 × 10-3 2.9 × 10-3 2.3 × 10-3 2.4 × 10-3 2.9 × 10-3 2.4 × 10-3 2.8 × 10-2 3.5 × 10-2 2.3 × 10-3 2.9 × 10-3 2.3 × 10-3 2.9 × 10-3 2.3 × 10-3 3.1 × 10-3 2.3 × 10-3

6.1 mHz 1.1 × 10-6 5.9 × 10-7 1.6 × 10-5 8.3 × 10-7 5.9 × 10-7 1.2 × 10-6 5.8 × 10-7

Tektronix DPO4102B Pearson 110 Weinschel 20dB Weinschel 40dB


Parameter/Equipment


RF Terminations – Reflection Coefficients

5 Hz to 9 kHz 9 kHz to 1 GHz (1 to 18) GHz (18 to 40) GHz (40 to 50) GHz

4.4 × 10-3 lin 4.8 × 10-3 lin 1.0 × 10-2 lin 1.3 × 10-2 lin 1.4 × 10-2 lin


Coaxial Thermistor Mounts –

Calibration Factor

1 μW to 100 mW

Reflection Coefficient

10 MHz to 1 GHz (1 to 10) GHz (10 to 18) GHz 10 MHz to 1 GHz (1 to 10) GHz (10 to 18) GHz

1.4 % 1.6 % 2.1 % 3.8 × 10-3 lin 5.3 × 10-3 lin 9.3 × 10-3 lin

Agilent 8478B

Transmission Trouble Testers –

Pulse Width Pulse Amplitude Pulse Rate Pulse Reflection Delay Time Impedance Insertion Loss Return Loss

1 ns to 100 μs 1 mV to 20 V 1 ns to 100 μs 1 ns to 200 μs 0 Ω 0.1 Ω to 500 Ω 1 MHz to 2.5 GHz 1 MHz to 2.5 GHz

1.4 × 10-2 6.3 × 10-2 5.8 × 10-11 1.5 × 10-2 1.2 mΩ 1.0 × 10-4 0.32 dB 0.51 dB

Fluke Networks DSX Artifacts Set, Tektronix DPO4102B, HP 3458A

RF Voltmeters – Voltage

(0 V to 400) V

0.1 mV to 10 V (-120 to 20) dBm

DC DC to 100 kHz 100 kHz to 1 GHz

5.8 × 10-5 1.6 × 10-4 0.15 dB

Fluke 5730A, Agilent E9304A, Keysight N5173B


Parameter/Equipment


Vector Voltmeters – Voltage

(0 V to 400) V

0.1 mV to 10 V (-120 to 20) dBm

DC DC to 100 kHz 100 kHz to 1 GHz

5.8 × 10-5 1.6 × 10-4 0.15 dB

Fluke 5730A, Agilent E9304A, Keysight N5173B

Field Strength Meters –

Frequency Frequency Response Amplitude Modulation Frequency Modulation

9 kHz to 18 GHz 9 kHz to 4 GHz (4 to 18) GHz 100 kHz to 18 GHz 100 kHz to 18 GHz

5.8 × 10-11 0.09 dB 0.15 dB 1.2 × 10-2 1.2 × 10-2

SRS FS725, Keysight 53210A, R&S FSMR, R&S NRP-Z37

AM/FM Test Sources –

Output Frequency Residual FM Residual AM Distortion Factor

1 MHz to 1 GHz 50 Hz to 3 kHz 50 Hz to 3 kHz (12.5 to 400) kHz

6.4 × 10-11 2.0 × 10-2 2.0 × 10-2 4.0 × 10-4

HP 8902A, Agilent 33250A

Dip Simulators –

DC Output Voltage

50 V (50 to 100) V (100 to 150) V (150 to 200) V (200 to 250) V (250 to 300) V (300 to 400) V

7.9 mV 8.8 × 10-5 1.4 × 10-2 1.1 × 10-2 1.0 × 10-2 9.3 × 10-3 8.2 × 10-3

H.P 34401A


Parameter/Equipment


Dip Simulators (cont) –

AC Output Voltage, (50 to 60) Hz

Line Frequency

Dip & Up Voltage DC Voltage (0 to 50) V 0 % 0 % to 40 % 40 % to 70 % 70 % to 80 % 80 % to 120 %

(50 to 100) V 0 % 0 % to 40 % 40 % to 70 % 70 % to 80 % 80 % to 120 %

(100 to 200) V 0 % 0 % to 40 % 40 % to 70 % 70 % to 80 % 80 % to 120 %

(200 to 300) V 0 % 0 % to 40 % 40 % to 70 % 70 % to 80 % 80 % to 120 %

(300 to 400) V 0 % 0 % to 40 % 40 % to 70 % 70 % to 80 % 80 % to 120 %

50 V (50 to 100) V (100 to 150) V (150 to 200) V (200 to 250) V (250 to 300) V (300 to 400) V 50 Hz to 60 Hz 0 V (0 to 20) V (20 to 35) V (35 to 40) V (40 to 60) V 0 V (0 to 40) V (40 to 70) V (70 to 80) V (80 to 120) V 0 V (0 to 80) V (80 to 140) V (140 to 160) V (160 to 240) V 0 V (0 to 120) V (120 to 210) V (210 to 240) V (240 to 360) V 0 V (0 to 160) V (160 to 280) V (280 to 320) V (320 to 480) V

0.3 V 3.3 × 10-3 3.0 × 10-3 2.4 × 10-3 2.0 × 10-3 1.8 × 10-3 1.5 × 10-3 3.5 × 10-4 0.35 V 2.9 × 10-2 2.5 × 10-2 2.5 × 10-2 2.4 × 10-2 0.37 V 2.6 × 10-2 2.4 × 10-2 2.4 × 10-2 2.3 × 10-2 0.37 V 2.7 × 10-2 2.4 × 10-2 2.4 × 10-2 2.4 × 10-2 0.35 V 2.8 × 10-2 2.5 × 10-2 2.5 × 10-2 2.4 × 10-2 0.37 V 2.6 × 10-2 2.4 × 10-2 2.4 × 10-2 2.3 × 10-2

H.P 34401A H.P 34401A Tektronix DPO4102B Teseq MD200A


Parameter/Equipment


Dip Simulators (cont) –

AC Voltage, (50 to 60 Hz) (100 to 110) V 0 % 0 % to 40 % 40 % to 70 % 70 % to 80 % 80 % to 120 %

(110 to 120) V 0 % 0 % to 40 % 40 % to 70 % 70 % to 80 % 80 % to 120 %

(120 to 220) V 0 % 0 % to 40 % 40 % to 70 % 70 % to 80 % 80 % to 120 %

(220 to 230) V 0 % 0 % to 40 % 40 % to 70 % 70 % to 80 % 80 % to 120 %

(230 to 380) V 0 % 0 % to 40 % 40 % to 70 % 70 % to 80 % 80 % to 120 %

(380 to 400) V 0 % 0 % to 40 % 40 % to 70 % 70 % to 80 % 80 % to 120 %

0 V (0 to 44) V (44 to 77) V (77 to 88) V (88 to 132) V 0 V (0 to 48) V (48 to 84) V (84 to 96) V (96 to 144) V 0 V (0 to 88) V (88 to 154) V (154 to 176) V (176 to 264) V 0 V (0 to 92) V (92 to 161) V (161 to 184) V (184 to 276) V 0 V (0 to 152) V (152 to 266) V (266 to 304) V (304 to 456) V 0 V (0 to 160) V (160 to 280) V (280 to 320) V (320 to 480) V

0.37 V 3.3 × 10-2 2.7 × 10-2 2.6 × 10-2 2.4 × 10-2 0.37 V 3.2 × 10-2 2.6 × 10-2 2.6 × 10-2 2.4 × 10-2 0.37 V 3.2 × 10-2 2.6 × 10-2 2.6 × 10-2 2.4 × 10-2 0.37 V 3.2 × 10-2 2.6 × 10-2 2.5 × 10-2 2.4 × 10-2 0.39 V 3.2 × 10-2 2.7 × 10-2 2.6 × 10-2 2.4 × 10-2 0.39 V 3.2 × 10-2 2.6 × 10-2 2.6 × 10-2 2.4 × 10-2

Tektronix DPO4102B Teseq MD200A


Parameter/Equipment


Dip Simulators3 (cont) –

Dip & Up Period

Phase Shifting Time

Rise & Fall Time

Inrush Current

1 ms (1 to 10) ms (10 to 20) ms (20 to 100) ms (100 to 200) ms (200 to 500) ms (0.5 to 2) s (2 to 5) s (5 to 10) s 1 ms (1 to 10) ms (10 to 20) ms 1 μs (1 to 10) μs (10 to 50) μs 50 A (50 to 100) A (100 to 500) A

0.028 μs 2.3 × 10-3 2.9 × 10-3 2.3 × 10-3 2.9 × 10-3 2.3 × 10-3 3.1 × 10-3 2.4 × 10-3 1.2 × 10-3 0.028 μs 2.3 × 10-3 2.9 × 10-3 0.02 μs 4.0 × 10-3 4.8 × 10-3 0.24 A 4.2 × 10-3 4.7 × 10-3

Tektronix DPO4102B Teseq MD200A Tektronix DPO4102B Teseq MD200A Tektronix DPO4102B Teseq MD200A Tektronix DPO4102B Pearson 110 Weinschel 40dB

E-field Probes3 – Correction Factor

5 kHz to 200 MHz (1 to 800) V/m 200 MHz to 1 GHz (1 to 300) V/m (1 to 18) GHz (1 to 200) V/m (18 to 40) GHz (1 to 200) V/m

0.13 0.13 0.13 0.14

IEEE Std.1309, IEC 61000-4-3; Reference E-field Probes, Power Amplifiers, TEM cell, FAC

SAR Probes3 – Conversion Factor

800 MHz to 6 GHz

1.3 × 10-1

IEEE Std 1528; SAR Measurement System, Agilent E9304A, H.P 778D


Parameter/Equipment


Dipole Antennas –

Antenna Factor VSWR Antenna Radiation Pattern

20 MHz to 18 GHz 20 MHz to 18 GHz 700 MHz to 18 GHz

1.1 dB 0.02 lin 1.4 dB

ANSI C63.5, SAE ARP958, CISPR 16-1-6; Keysight N5234A, Keysight 85054D

Biconical Antennas –

Antenna Factor VSWR

20 MHz to 18 GHz 20 MHz to 18 GHz

1.2 dB 0.02 lin

ANSI C63.5, SAE ARP958, CISPR 16-1-6; Keysight N5234A, Keysight 85054D,

Log Periodic Antennas –

Antenna Factor VSWR

20 MHz to 6 GHz 20 MHz to 6 GHz

1.2 dB 0.02 lin

ANSI C63.5, SAE ARP958, CISPR 16-1-6; Keysight N5234A, Keysight 85054D

Loop Antennas – Antenna Factor

10 Hz to 30 MHz

1.3 dB

ANSI C63.5, SAE ARP958, CISPR 16-1-6; Standard Loop Antenna, HP 3458A

Monopole Antennas – Antenna Factor

1 kHz to 30 MHz

1.4 dB

ANSI C63.5, SAE ARP958, CISPR 16-1-6, ECSM; Keysight E5061B, Keysight 85032B

Horn Antennas –

Antenna Factor VSWR Radiation Pattern

200 MHz to 18 GHz (18 to 40) GHz 200 MHz to 40 GHz 700 MHz to 18 GHz

0.9 dB 1.4 dB 0.02 lin 1.4 dB

ANSI C63.5, SAE ARP958, CISPR 16-1-6; Keysight N5234A, Keysight 85054D, Maury 85056KE02, Keysight 85056D


VI. Magnetic Quantities

Parameter/Equipment


Flux Meters

0.1 mWb (0.1 to 1) mWb 1 mWb to 1 Wb (1 to 10) Wb

6.0 × 10-3 1.7 × 10-3 8.2 × 10-4 8.6 × 10-4

Walker MTC-1 H.P 34401A

Flux Sources

(0.1 to 1) mWb (1 to 10) mWb (10 to 100) mWb (0.1 to 1) Wb (1 to 10) Wb

1.3 × 10-4 1.2 × 10-5 3.3 × 10-6 1.1 × 10-5 2.1 × 10-5

Fluke 8508A H.P 53131A Rohde & Schwarz RTO1022

Magnetometers

0 mT (0 to 1) mT (1 to 25) mT (25 to 50) mT (50 to 150) mT (150 to 500) mT (500 to 1000) mT (1 to 1.9) T

2.2 μT 6.5 × 10-3 3.2 × 10-3 3.8 × 10-3 2.3 × 10-3 7.2 × 10-4 7.0 × 10-4 5.5 × 10-4

Walker FGM-3D1 KRISS KMS-1003 Ohm-labs CS-10 H.P 34401A Metrolab PT-2025 Lakeshore 475 Lakeshore FC-EM7

Reference/Standard Magnets

(5 to 10) mT (10 to 100) mT (0.1 to 1) T (1 to 2) T

2.2 × 10-3 8.3 × 10-4 1.1 × 10-3 9.0 × 10-4

Walker FGM-3D1 KRISS KMS-1003 Ohm-labs CS-10 H.P 34401A Metrolab PT-2025 Lakeshore 475 Lakeshore FC-EM7

Flux Meters

0.1 mWb (0.1 to 1) mWb 1 mWb to 1 Wb (1 to 10) Wb

6.0 × 10-3 1.7 × 10-3 8.2 × 10-4 8.6 × 10-4

Walker MTC-1 H.P 34401A


VII. Thermodynamics

Parameter/Equipment


Temperature Generators –

Dry-Block Calibrators Ice-Point Baths Isothermal Liquid Baths Furnaces Temperature Controlled Chambers/Ovens

(-80 to 420) 0 (-80 to 420) (250 to 1 100) (-80 to 200) (200 to 400)

0.05 0.02 0.03 1.0 0.7 1.0

Accumac AM1960 ASL F650-B-Y Accumac AM1960 ASL F650-B-Y Accumac AM1960 ASL F650-B-Y KRISS S-Type HP 34401A HART 9101 Agilent 34970A

Temperature Indicators/ Recorders/Controllers, Temperature Calibrators –

With Sensor Thermoelectric Type

Resistance Type Without Sensor Thermoelectric Type

Resistance Type

(-80 to 250) (250 to 500) (500 to 1 100) (-80 to 250) (250 to 500) (-80 to 1 100) (-80 to 500)

0.2 0.8 1.8 0.04 0.06 0.22 0.13

HCT S-Type Accumac AM1960 ASL F650-B-Y Kambic OB-22/2 ULT & OB-22/2 Fluke 6055 WOO JIN BT-003 HART 9101 HP 3458A Accumac AM1960 ASL F650-B-Y Kambic OB-22/2 ULT & OB-22/2 Fluke 6055 Heto CB208 Fluke 5730A HP 3458A Fluke 5730A HP 3458A IET HARS-X-10-.001-K


Parameter/Equipment


Glass Thermometers

(-80 to 250)

0.05

ASL F650-B-Y Yunnan WZPB-10 Kambic OB-22/2 ULT & OB-22/2

Resistance Thermometers3 – IPRT

(-80 to 250) (250 to 500)

0.05 0.08

Accumac AM1960 ASL F650-B-Y Kambic OB-22/2 ULT & OB-22/2 Fluke 6055

Thermal Expansion Thermometers3 – Bimetal

(-80 to 250)

0.3

Accumac AM1960 ASL F650-B-Y Kambic OB-22/2 ULT & OB-22/2

Thermocouples3 –

Jewelry Thermocouple

Base metal Thermocouple

(0 to 500) (500 to 1 100) (-80 to 250) (250 to 500) (500 to 1100)

0.5 1.6 0.6 0.8 1.9

Kriss S-Type Woo Jin BT-003 HP 3458A Hart 9101 Pyro 96 Kambic OB-22/2 ULT & OB-22/2 Fluke 6055 Accumac AM1960 ASL F650-B-Y

Temperature Transducers3

(-80 to 250)

0.18

ASL F650-B-Y Yunnan WZPB-10 Kambic OB-22/2 ULT & OB-22/2 Hart 9101 HP 3458A

Standard Radiation Thermometers

(-18 to 200) (200 to 500) (500 to 800) (800 to 1000)

1.2 2.2 3.7 5.3

Heitronics TRTⅡ Isotech 982, 976 Infrared Systems Developments IR574 Kambic OB-15/2 BBLT Heitronics KT19.82II


Parameter/Equipment


Thermal Image Apparatus

(-18 to 200) (200 to 500) (500 to 800) (800 to 1000)

1.2 2.2 3.7 5.3

Heitronics TRTⅡ Isotech 982, 976 Infrared Systems Developments IR574 Kambic OB-15/2 BBLT Heitronics KT19.82II

Dew-Point Hygrometers – Alumina Thin Film

( -20 to 47) DP

0.7 DP

Michell S8000 Remote Shinyei SRH-1R135ADR

Relative Humidity Hygrometers3 –

Hair: Humidity Thermometry

Polymer Thin-Film:

Humidity Thermometry

(30.0 to 90.0) % R.H. (-20 to 50) (5 ∼ 95) % R.H. (-20 to 50)

2.9 % R.H. 0.60 2.1 % R.H. 0.60

Michell S8000 Remote Hart 1529-R Espec PL-3J Espec PSL-2KP Michell S8000 Remote Hart 1529-R Espec PL-3J Shinyei SRH-1R135ADR

Temperature Humidity Recorders –

Hygrothermograph, etc.: Humidity Thermometry

(30.0 ∼ 90.0) % R.H. (-20 to 50)

2.8 % R.H. 0.83

MICHELL S8000 REMOTE HART 1529-R ESPEC PL-3J ESPEC PSL-2KP


Parameter/Equipment


Transducers – Dewpoint/Relative Humidity

(9 to 95) % R.H.

2.6 % R.H.

Michell S8000 Remote Hart 1529-R Espec PL-3J Shinyei SRH-1R135ADR

Humidity generators –

Flow Mixing Humidity Generator Constant Temperature and Humidity Chamber:

Humidity Thermometry

(5 to 95) % R.H. (10 to 98) % R.H. (-80 to 250)

1.5 % R.H. 3.2 % R.H. 0.7

Michell S8000 Remote Hart 1529-R Michell S8000 Remote Fluke 2620A

VII. Acoustics & Vibration

Parameter/Equipment


Sound Calibrator –

Multifunction Calibrator

(94.0 to 114.0) dB (114.0 to 134.0) dB

Pistonphone, Sound Calibrator

(94.0 to 134.0) dB

31.5 Hz (31.5 to 63) Hz (63 to 8000) Hz (8000 to 12 500) Hz 250 Hz 1000 Hz

0.14 dB 0.12 dB 0.11 dB 0.13 dB 0.11 dB 0.11 dB

G.R.A.S 40AG Agilent 34401A H.P 53131A G.R.A.S 12AK G.R.A.S 40AG Agilent 34401A H.P 53131A G.R.A.S 12AK


Parameter/Equipment


Microphones –

Pistonphone

(-50.00 dB to -20.00) dB

3-Port Coupler

(-50.00 to -20.00) dB

250 Hz 31.5 Hz (31.5 to 40) Hz (40 to 50) Hz (50 to 6300) Hz (6300 to 8000) Hz (8000 to 10 000) Hz (10 000 to 12 500) Hz (12 500 to 16 000) Hz

0.14 dB 0.13 dB 0.12 dB 0.11 dB 0.10 dB 0.27 dB 0.32 dB 0.39 dB 0.57 dB

G.R.A.S 40AG NI PCI-4461 G.R.A.S 90CA G.R.A.S 40AG Agilent 34401A H.P 53131A H.P 33120A G.R.A.S 12AK Spektra SQ-4.2 S.M.S.L SAP-8

Sound Level Meters –

Multifunction Calibrator

(94.0 to 114.0) dB

3-Port Coupler

(84.0 to 114.0) dB

(63 to 4000) Hz (4 000 to 8000) Hz 125 Hz (125 to 2500) Hz (2 500 to 8000) Hz

0.3 dB 0.4 dB 0.4 dB 0.2 dB 0.3 dB

B&K 4226 G.R.A.S 40AG Agilent 33210A Agilent 34401A Kriss None Kriss SP-2028

Vibration Calibrators –

Vibration Calibrator

Vibration Tester

(20 to 630) Hz (630 to 1250) Hz (3 to 10) Hz (10 to 630) Hz (630 to 3000) Hz

1.8 × 10-2 1.9 × 10-2 3.4 × 10-2 2.9 × 10-2 3.0 × 10-2

B&K 8305 B&K 2693-014 Agilent 34401A H.P 53131A B&K 8305 B&K 2693-014 Agilent 34401A H.P 53131A NI PXI-5122


Parameter/Equipment


Vibration Transducer

1 Hz (1 to 8) Hz (8 to 10) Hz (10 to 20) Hz (20 to 630) Hz (630 to 1250) Hz (1250 to 2500) Hz (2500 to 5000) Hz (5000 to 10000) Hz (10000 to 15000) Hz (15000 to 20000) Hz

2.4 × 10-2 2.1 × 10-2 2.0 × 10-2 1.3 × 10-2 1.1 × 10-2 1.2 × 10-2 1.7 × 10-2 2.1 × 10-2 2.9 × 10-2

4.1 × 10-2

5.2 × 10-2

B&K 8305 Agilent/ 34401A H.P/ 34401A Agilent 33210A Tektronix/ TDS5104 Ni PXI-5122 B&K 4809 B&K 2718 APS APS-113 APS APS-125

Vibration Transducer (Shock)

200 m/s2 (200 to 500) m/s2 (500 to 2 000) m/s2

3.6 × 10-2 3.2 × 10-2 3.1 × 10-2

PCB 301A12 Tektronix DPO4104B B&K 2693-014 IMV I260-SA1M

Vibration Measuring Instruments –

Acceleration

Velocity

Displacement

10 Hz (10 to 40) Hz (40 to 100) Hz (100 to 630) Hz (630 to 1 250) Hz (1250 to 2500) Hz 10 Hz (10 to 40) Hz (40 to 100) Hz (100 to 630) Hz (630 to 1250) Hz (1250 to 2500) Hz 10 Hz (10 to 160) Hz (160 to 315) Hz

1.7 × 10-2 1.8 × 10-2 1.7 × 10-2 1.8 × 10-2 1.9 × 10-2

2.1 × 10-2 1.9 × 10-2 1.8 × 10-2 1.7 × 10-2 1.8 × 10-2 2.1 × 10-2 2.7 × 10-2 1.7 × 10-2 1.6 × 10-2 2.2 × 10-2

B&K 8305 Agilent/ 34401A Agilent 33210A B&K 4809 B&K 2718

Shock Instruments

200 m/s2 (200 to 500) m/s2 (500 to 1000) m/s2 (1000 to 2000) m/s2

4.9 × 10-2 3.5 × 10-2 3.3 × 10-2 3.2 × 10-2

PCB 301A12 Tektronix DPO4104B B&K 2693-014 IMV I260-SA1M


Parameter/Equipment


Vibration tester –

Accel Frequency Displacement Shock

(3 to 10) Hz (10 to 630) Hz (630 to 3000) Hz (3 to 8) Hz (8 to 3000) Hz (3 to 10) Hz (10 to 40) Hz (40 to 100) Hz (100 to 160) Hz (160 to 315) Hz

(200 to 2000) m/s²

3.3 × 10-2 2.9 × 10-2 3.1 × 10-2

0.60 mHz 5.8 mHz

3.4 × 10-2 2.9 × 10-2 3.0 × 10-2 3.6 × 10-2 8.5 × 10-2

5.0 × 10-2

B&K 8305, PCB 301A12, B&K 2693-014, Agilent 34401A, H.P 53131A, NI PXI-5122, Tektronix DPO4104B

VIII. Optical Quantities

Parameter/Equipment


Illuminance Meters

1 lx (1 to 2000) lx

3.0 × 10-2 2.8 × 10-2

Illuminance calibration system

UV Irradiance Meters –

254 nm 365 nm 405 nm

50 μW/cm2 to 1 mW/cm2 60 μW/cm2 to 200 mW/cm2 60 μW/cm2 to 70 mW/cm2

4.8 × 10-2 4.8 × 10-2 4.8 × 10-2

Optronic OL730A-5A Keithlet 485


Parameter/Equipment


Broadband Light Sources –

Wavelength Optical Output

1310 nm

1550 nm

1310 nm, 1550 nm (-50 to 0) dBm (-60 to -50) dBm (-60 to 0) dBm

5.5 × 10-7 0.08 dB 0.09 dB 0.08 dB

ADCMT 8471, EXFO IQS Optical calibration system

Optical Attenuators –Attenuation, 1310 nm, 1550 nm

(-60 to 0) dB

0.04 dB

EXFO IQS Optical calibration system

Optical Loss Testers –

Wavelength Optical output

1310 nm 1550 nm

Linearity

1310 nm, 1550 nm

1310 nm, 1550 nm (-50 to 0) dBm (-60 to -50) dBm (-60 to 0) dBm (-60 to 0) dB

5.5 × 10-7 0.08 dB 0.09 dB 0.08 dB 0.04 dB



Parameter/Equipment


Optical Multimeters –

Optical Input 1310 nm 1550 nm

Linearity

1310 nm, 1550 nm

(-50 to 0) dBm (-60 to -50) dBm (-60 to 0) dBm (-60 to 0) dB

0.08 dB 0.09 dB 0.08 dB 0.04 dB


Optical Spectrum Analyzers –

Wavelength

Resolution

1310 nm, 1550 nm

Optical input

1310 nm 1550 nm

Linearity

1310 nm, 1550 nm

1310 nm, 1550 nm RBW (0.1 to 1) nm (-50 to 0) dBm (-60 to -50) dBm (-60 to 0) dBm (-60 to 0) dB

0.084 nm 0.084 nm 0.08 dB 0.09 dB 0.08 dB 0.04 dB



Parameter/Equipment


Optical Time Domain Reflectometers –

Wavelength Length

1310 nm

1550 nm 1310 nm

Return Loss

1550 nm

1310 nm, 1550 nm 3 km 13 km 3 km 13 km 3 km 13 km 3 km 13 km

0.35 nm 0.1 m 0.34 m 0.1 m 0.34 m 0.06 dB 0.06 dB 0.06 dB 0.06 dB

KRISS 3 km/ 13 km Optical fiber standard length KRISS 3 km/ 13 km Optical fiber standard loss

ASE Light Sources –


1310 nm 1550 nm


5.5 × 10-7 0.08 dB 0.09 dB 0.08 dB


Optical Power Stabilized Lasers and LDs –


1310 nm 1550 nm


5.5 × 10-7 0.08 dB 0.09 dB 0.08 dB



IX. Chemical Quantities

Parameter/Equipment


Gas analyzers3 –

Oxygen (O2) Carbon monoxide (CO) Methane (CH4) Carbon Dioxide (CO2) hydrogen sulfide (H2S)

(0 to 10.5) cmol/mol (0 to 105) μmol/mol (0 to 2.2) cmol/mol (0 to 2.2) cmol/mol (0 to 53) μmol/mol

4.0 × 10-2 2.4 × 10-2 1.7 × 10-2 2.1 × 10-2 4.5 × 10-2

Standard Gas (O2) Standard Gas (CO) Standard Gas (CH4) Standard Gas (CO2) Standard Gas (H2S)

_____________________________ 1 This laboratory offers commercial and field calibration services.

2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer’s device and to influences from the circumstances of the specific calibration.

3 Field calibration service is available for this calibration and this laboratory meets A2LA R104 – General Requirements: Accreditation of Field Testing and Field Calibration Laboratories for these calibrations. Please note the actual measurement uncertainties achievable on a customer's site can normally be expected to be larger than the CMC found on the A2LA Scope. Allowance must be made for aspects such as the environment at the place of calibration and for other possible adverse effects such as those caused by transportation of the calibration equipment. The usual allowance for the actual uncertainty introduced by the item being calibrated, (e.g. resolution) must also be considered and this, on its own, could result in the actual measurement uncertainty achievable on a customer’s site being larger than the CMC.

4 In the statement of CMC, percentages are percentage of reading, unless otherwise indicated. 5 In the statement of CMC, the unitless CMC was calculated as a relative standard uncertainty of

measurement. 6 This scope meets A2LA’s P112 Flexible Scope Policy.

calibrationhct.co.kr/upload/certificate/a2la scope_eng.pdf · 2020-07-28 · 2.7 μm; standard...

Documents