scissor lifts...second scissor capacity 3500kg platform length 4800mm lift/lower 45 seconds lifting...
TRANSCRIPT
SCISSOr LIFTSProduct�guide
H8101ME3.0�tonne�mobile�mid-rise�scissor�lift
Features
• Low profile (105mm) structure for on-ground installation
• Low voltage control
• Non return valve provides safety against hydraulic failure
• Dual hydraulic circuit with solenoid valves that protects
againest pipe breakage
• Synchronism of platforms without any torsion bar
• No mechanical locking therefore no air requirement
• Set of 4 rubber pads
• 12 months warranty on parts and labour*
Benefits
• Mobile capability, suitable for workshops for limited space
• Ideal for tyre & car body shops
• Full access to all sides of vehicles
• Low profile platform ideal for lifting large range of vehicles
including low skirted sport cars
Console
Console
technical�data
Lifting capacityPlatform lengthPlatform depthOverall widthEach platform widthDistance between platformsLifting heightWeight
3000kg1450mm105mm1335mm535mm800mm960mm450kg
Key�features
• 3.0 tonne
• Mobile
• Low profile
• Single phase
• Ideal for tyre shopsimportant Please read supply and installations notes on back page.
Do not scale. *Subject to correct maintenance and usage. No liability accepted for specificationswhich may be subject to alteration on all products pictures are for illustration purposes only.
H8101E3.2�tonne�short�platform�mid-rise�scissor�lift
Features
• Low profile (105mm) structure for on-ground istallation
• Low voltage control
• Non return valve provides safety against hydraulic failure
• Dual hydraulic circuit with solenoid valves that
protects against pipe breakage
• Synchronism of platforms without any torsion bar
• No mechanical locking therefore no air requirement
• 12 months warranty on parts and labour*
Benefits
• Ideal for tyre & car body shops
• Full access to all sides of vehicles
• Low profile platform ideal for lifting large range of
vehicles including low skirted sport cars
Console
Console
technical�data
Lifting capacityPlatform lengthPlatform depthOverall widthEach platform widthdistance between platformsLifting heightWeight
3200kg1450mm105mm1335mm535mm800mm960mm450kg
Key�features
• 3.2 tonne
• Ideal for tyre shops
• Low profile
• Single phase
• Ideal for tyre and car body shopsimportant Please read supply and installations notes on back page.
Do not scale. *Subject to correct maintenance and usage. No liability accepted for specificationswhich may be subject to alteration on all products pictures are for illustration purposes only.
H8603/1E3.6�tonne�short�platform�high-rise�in-ground�scissor�lift
Features
• Hydraulically synchronised platforms
• Low voltage control system
• Full access to sides, front and rear of vehicle
• Low ground clearance ideal for very low skirted vehicles
• Includes platform extensions (both sides)
• Hydraulic platforms synchronisation
• Complete with lifting blocks
• Control panel allows precise lifting
• Sensors ensures platform remains level during lifting
• ratchet safety mechanism
• 12 months warranty on parts and labour*
Benefits
• Improves utilisation of workshop space
• Ideal for service bays, tyre shops, general repair, brake
repairs, suspension and transmission replacement and
body shops
• Flush fitted application allows for vehicles to drive over
the platforms in all directions
Console
2000 max
Console
technical�data
Lifting capacityPlatform lengthPlatform depthOverall widthEach platform widthDistance between platformsLifting height3 Phase1 PhasePneumatic feed requirement
3600kg1640mm-2040mm330mm2030mm550mm930mm1830mmMotor 380V, 2.2kWMotor 220V 2.2kW6-8 bar air supplyAir and air regulator required
Key�features
• 3.6 tonne
• Flush fitted
• High-rise
• Three phase or Single phase
• ratchet locking mechanismimportant Please read supply and installations notes on back page.
Do not scale. *Subject to correct maintenance and usage. No liability accepted for specificationswhich may be subject to alteration on all products pictures are for illustration purposes only.
H8903/1E3.2�tonne�extra�low�profile�hydraulic�scissor�lift
Features
• Hydraulically synchronised platforms
• Low voltage control system
• Full access to sides, front and rear of vehicle
• Low ground clearance ideal for very low skirted vehicles
• Hydraulic platforms synchronisation
• Control panel allows precise lifting
• Non return valve provides safety against hydraulic failure
• Dual hydraulic circuit with solenoid valves that protects
against pipe breakage
• Synchronism of platforms without any torsion bar
• No mechanical locking therefore no air requirement
• Complete with lifting blocks
• 12 months warranty on parts and labour*
Benefits
• Ideal for service bays, tyre shops, general repair, brake
repairs, suspension and transmission replacement and
bodyshops
• Low profile platform ideal for lifting large range of vehicles
including low skirted sports cars
technical�data
Lifting capacityPlatform lengthPlatform depthOverall widthEach platform widthDistance between platformsLifting height3 Phase1 Phase
3200kg1500mm105mm1870mm535mm800mm1900mmMotor 380V, 2.2kWMotor 220V 2.2kW
Key�features
• 3.2 tonne
• Low profile
• High-rise
• Three phase or Single phase
• Full access to sidesimportant Please read supply and installations notes on back page.
Do not scale. *Subject to correct maintenance and usage. No liability accepted for specificationswhich may be subject to alteration on all products pictures are for illustration purposes only.
Console
Console
H88403Sr SHALLOW rECESS4.0�tonne�service,�wheel�alignment,�Mot�&�atl�scissor�lift
Features
• 180mm recess depth
• 4400mm & 4800mm platform lengths available
• Automatically activated, mechanical safety locks
• Manual device for lowering encase of power failure
• Optional auxiliary lift for wheel free working
• Suitable for service, MOT/ATL and alignment purposes
• Maximum operating stability under all loading conditions
thanks to a set of master-slave cylinders with mechanical
synchronisation (not electronic)
• Ideal for service bays, tyre shops and general repair
• Complete with lifting blocks
Benefits
• Fits into many existing recesses
• Different length platforms gives greater flexibility
• Automatically activated mechanical safety locks
• Photocells for platform synchronisation control
• Limit switch with acoustic warning for the complete
lowering
• Photocells for platform synchronisation
• Limit switch with acoustic warning on final lowering
• Dead man controls
technical�data
Capacity 4000kgPlatform length 4400mm/4800mmLift/lower 50 secondsLifting height 2100mmMotor 3.5kW 230-400v/50Hz-3phPnaumatic feed 8-10 barrequirement Air operated and air
regulator required
Key�features
• 180mm recess - 4400mm or 4800mm platform
• Fits into many existing recesses
• Three phase or Single phase
• Service, MOT/ATL and wheel alignment
versions availableimportant Please read supply and installations notes on back page.
Do not scale. *Subject to correct maintenance and usage. No liability accepted for specificationswhich may be subject to alteration on all products pictures are for illustration purposes only.
H88453SS4.5�tonne�service�&�wheel�alignment�space�saver�scissor�lift
Features
• Control box fitted under platform
• Suitable for service and alignment purposes
• The torsion bar (internationally patented), grants the best
long-term leveling performances, without maintenance
• The rear slip plate, reinforced with tempered steel is
1830mm long when fitted to an alignment lift
• Improves utilisation of workshop space
• Full access to sides, front and rear or vehicle
• Ideal for service bays, tyre shops and general repair
• Complete with lifting blocks
• 12 Months warranty on parts and labour*
Benefits
• More room around lift due to space saving control box
• Automatically activated mechanical safety locks
• Photocells for platform synchronisation
• Limit switch with acoustic warning on final lowering
• Dead man controls
technical�data
Capacity 4500kgSecond scissor capacity 3500kgPlatform length 4800mmLift/lower 45 secondsLifting height 2125mmMotor 3.5kW 230-400v/50Hz-3phPnaumatic feed 8-10 bar filtered/lubricatedrequirement Air and air regulator required3 Phase Motor 400V 3/50Hz 3.5kW
Key�features
• 4.5 tonne - 4800mm platform
• Space saving control box**
• Three phase or Single phase
• Service and wheel alignment versions
available important Please read supply and installations notes on back page.Do not scale. *Subject to correct maintenance and usage. No liability accepted for specifications
which may be subject to alteration on all products pictures are for illustration purposes only.**Only availale on non ATL versions.
H884534.5�tonne�service,�wheel�alignment,�Mot�&�atl�scissor�lift
Features
• Suitable for service, MOT/ATL and alignment purposes,
offers maximum stability and precision during the lifting
phase
• The torsion bar (internationally patented), grants the best
long-term leveling performances, without maintenance
• The rear slip plate, reinforced with tempered steel is
1785mm long when fitted to an alignment lift
• Improves utilisation of workshop space
• Full access to sides, front and rear or vehicle
• Ideal for service bays, tyre shops and general repair
• Complete with lifting blocks
• 12 Months warranty on parts and labour*
Benefits
• Automatically activated mechanical safety locks
• Photocells for platform synchronisation
• Limit switch with acoustic warning on final lowering
• Dead man controls
technical�data
Capacity 4500kgSecond scissor capacity 3500kgPlatform length 4800mmLift/lower 45 secondsLifting height 2125mmMotor 3.5kW 230-400v/50Hz-3phPnaumatic feed 8-10 bar filtered/lubricatedrequirement Air and air regulator required3 Phase 3.5kW motor 400V 3/50Hz
Key�features
• 4.5 tonne - 4800mm platform
• Unique patented torsion bar
• Three phase or Single phase
• Service, MOT/ATL and wheel alignment
versions availableimportant Please read supply and installations notes on back page.
Do not scale. Subject to correct maintenance and usage. No liability accepted for specificationswhich may be subject to alteration on all products pictures are for illustration purposes only.
H885035.0�tonne�service,�wheel�alignment,�Mot�&�atl�space�saver�scissor�lift
Features
• Anti-skid access ramps on the platform allow maximum
space on the floor with the lift raised
• The sliding parts on the metallic wheels are fitted with self
lubricating brushes meaning minimal maintenance and
maximum reliability over time
• The lifting arms are made from solid steel bars rather
than tubular section bars
• The mechanical locks grant precision, safety and long
life of the lift
• 12 Months warranty on parts and labour*
Benefits
• Automatically activated mechanical safety locks
• Photocells for platform synchronisation control
• Limit switch with acoustic warning while lowering
• Dead man controls
technical�data
Capacity 5000kgPlatform length 5200mmLift/lower 50 secondsLifting height 2100mmMotor 3.5kW 230-400v/50Hz-3phPnaumatic feed 8-10 barrequirement Air operated and air
regulator required
Key�features
• 5 tonne - 5200mm platform
• Unique patented torsion bar
• Suitable for LWB vans
• Service, MOT/ATL and wheel alignment
versions availableimportant Please read supply and installations notes on back page.
Do not scale. Subject to correct maintenance and usage. No liability accepted for specificationswhich may be subject to alteration on all products pictures are for illustration purposes only.
PLANExample�site�layout
Console Console
important Please read supply and installations notes on back page.Do not scale. *Subject to correct maintenance and usage. No liability accepted for specifications
which may be subject to alteration on all products pictures are for illustration purposes only.
ACCESSOrIESScissor�lifts
lighting�Kit
Bradbury’s lighting kits are 1.6 metres long and ideal for
scissor lifts, 2 post lifts and 4 post lifts- they provide a bright
and powerful illumination for the garage’s working area.
BrS�-�Bradbury�rolling�System
This revolutionary Bradbury idea will completely change
your working method when used with a Wheel Alignment
machine.
Jacking�Beams
Bradbury jacking beams are a high quality range which meetall your needs.Finger guards fitted as standard.A range oflifting blocks available.Manual or air operated with double extending top beam forMOT use.
Manual/Air Operated Jacking BeamsBJB20Sr(A) All class IV MOT, Service, ATL, Scissor & hybrid lifts
BJB28r(A)DEATL1591 All class VII MOT, Service, ATL, Scissor & hybrid lifts
BJB20r(A)DEATL1391 All class IV MOT, Service, ATL, Scissor & hybrid lifts
BJB40r(A)DE All high tonnage lifts
BrS - Bradbury rolling SystemCompatible with all lifts
Pneumatic functioning
No power supply needed
Easy Installing, plug and play
Ideal for 3-D alignments and
SUV/OFF rOAD vehicles
Capacity up to 3 tonnes
SUV/4 x 4 barsH8603E or H8903E 4 x 4 Bars
Lighting Kit Extension CablesA802HE 2 2 m hose extension
A803HE 3.5m hose extension