sbs-25 25' high soccer ballstopper system specification · cleat hardware (stainless steel)...
TRANSCRIPT
®Aluminum Athletic Equipment
1000 Enterprise Drive, Royersford, PA 19468 Toll Free: (800) 523-5471 Fax: (610) 825-2378
www.AAEsports.com1 of 12
SBS-2525' High Soccer BallStopper System
Specification
DATE:CATEGORY:
CAD FILE:DWN. BY:
MODEL:
NOTE:
DESCRIPTION:
N.R.CCopyright 2011 Aluminum Athletic Equipment Co.
D
C
B
A
6 5 4 3 2 1
D
C
B
A
8 7 6 5 4 3 2 1
®Aluminum Athletic Equipment
1000 Enterprise Drive, Royersford, PA 19468 Toll Free: (800) 523-5471 Fax: (610) 825-2378
www.AAEsports.com
20'-0"240"MAX
20'-0"240"MAX
20'-0"240"MAX
Refer to AssociationGuidlines for
Placement Distance
Post Spacing Distance is not to Exceed Specification
Field of Play
End Line
Left EndPost
Inner Post Inner Post Right EndPost
SBS-25 Specifications
4/13/2018SBS-25
25' HIGH BALLSTOPPER SYSTEM
CUSTOMERDWG. NO.
SBS-25-C-0022 of 12
SBS-25Specifications
Concrete Footing Placement Specification
®Aluminum Athletic Equipment
1000 Enterprise Drive, Royersford, PA 19468 Toll Free: (800) 523-5471 Fax: (610) 825-2378
www.AAEsports.com
25'-6"(REF)
A
C
D
B
Net(height varies depending on system height and attachment method)
DETAIL A
PostCap
Eyebolt(Stainless Steel)
Hanging Pulley(Galvanized Steel)
Pear Clip(Stainless Steel)
Cable Clamp(Galvanized Steel)
Net with integrated Clear Vinyl Coated (Galvanized Steel) Cable
Heavy DutyBraided NylonRope (Black)
O-Ring(Brass)
DETAIL C
Cleat(Galvanized Steel)
Clear Vinyl Coated (Galvanized Steel)
Vertical Attachment Cable
Cleat Hardware(Stainless Steel)
Pear Clip(Stainless Steel)
DETAIL D
Tensioner Kit(Galvanized Steel)
DETAIL B
Open Eyebolt(Stainless Steel)
(End Posts Only)
SBS-25 SpecificationsPost (Aluminum):
- 4" x .226" wall aluminum tube (Mill Aluminum 6061T6)
- 29'-0" Overall Length (25'-6" out of ground sleeve)
- Weight = 117lbs./ea.- All Hardware is RUSTPROOF
Netting:- Net: #AAE N367, 3-1/2" Sq. Knotted Nylon, FR,DBB, length to vary, 1/4" MFP Rope Border, UVprotected and 1/4" cable hog tied to top of net
A
B
C
D
DRAWN BY: CAD FILE:
MODEL: DATE:
NOTE:
SBS-25 Specifications
3/27/2019SBS-25
NR
Upright Assembly Specification
DESCRIPTION
123456
A
B
C
D
12345678
CATEGORY:
CUSTOMER
SBS-25 Upright Specification
DWG. NO.
SBS-25-C-003Copyright 2011 Aluminum Athletic Equipment Co.C
SBS-25Upright Specification
3 of 12
®Aluminum Athletic Equipment
1000 Enterprise Drive, Royersford, PA 19468 Toll Free: (800) 523-5471 Fax: (610) 825-2378
www.AAEsports.com
2'-6"30"
HoleDiameter
4"
5'-3"63"
HoleDepth
4'-9"57"
SleeveLength
6"
3'-6"42"to
Stop Bolt
6" Grass
Compacted Subgrade
Grass
Concre
te
Concre
te
Crushed Stone
Natural Grass FieldFooting Specification
Top of post sleeve should be even with soil.2
6"
5'-3"63"
HoleDepth
2'-6"30"
HoleDiameter
4'-9"57"
SleeveLength
4" 6"
3'-6"42"to
Stop Bolt
Stabilzed Subgrade
Crushed Stone
Concre
te
Concre
te
AggregateAggregate
Artificial Grass FieldFooting Specification
TurfTurf
Top of post sleeve should be even with aggregate.2
A
B
C
D
DRAWN BY: CAD FILE:
MODEL: DATE:
NOTE:
SBS-25 Specifications
4/13/2018SBS-25
N.R.
Grass & Turf Footing Specification
DESCRIPTION
123456
A
B
C
D
12345678
CATEGORY:
CUSTOMERDWG. NO.
SBS-25-C-004Copyright 2011 Aluminum Athletic Equipment Co.C
SBS-25Concrete FootingSpecification
Note: **Consult Local Codes4 of 12
Concrete Footing Specification
®Aluminum Athletic Equipment
1000 Enterprise Drive, Royersford, PA 19468 Toll Free: (800) 523-5471 Fax: (610) 825-2378
www.AAEsports.com
Lower End PostLower Horizontal Cable
"Tensioner"Collar Assembly
Note: Hardware denoted with "A" is included in item
#12 "tensioner kit"
14
15
16
11
A
Right End PostLower Horizontal Cable
"Anchor Shackle"Collar Assembly
1114
1615
Cable loop end show for reference only(not pre-installed)
When installingcable, clamploop goes on cutside.
A
AA
A
Left & Right End PostUpper Vertical Cable
"Anchor Shackle"Collar Assembly
16
15
1411 When
installing cable, clamp loop goes on cut side.
Left & Right End PostLower Vertical Cable
"Tensioner"Collar Assembly
Cable loop end show for reference only(not pre-installed)
A
Note: Hardware denoted with "A" is included in item
#12 "tensioner kit"
11
16
15
14
A
Inner PostLower Horizontal Cable
"Pear Clip"Collar Assembly
14
1315 16
11
1819
17
20 21
Left & Right End PostMid Vertical Cable
"Open Eyebolt"Collar Assembly
A
B
C
D
DRAWN BY: CAD FILE:
MODEL: DATE:
NOTE:
SBS-25 Specifications
4/13/2018SBS-25
NR
Various Collar Assemblies
DESCRIPTION
123456
A
B
C
D
12345678
CATEGORY:
CUSTOMER
SBS-25 Assembly Instructions
DWG. NO.
SBS-25-C-005Copyright 2011 Aluminum Athletic Equipment Co.C
SBS-25Cable Collar Assembly Diagrams 5 of 12
®Aluminum Athletic Equipment
1000 Enterprise Drive, Royersford, PA 19468 Toll Free: (800) 523-5471 Fax: (610) 825-2378
www.AAEsports.com
Model No. SBS-25Parts List
6 of 12
®Aluminum Athletic Equipment
1000 Enterprise Drive, Royersford, PA 19468 Toll Free: (800) 523-5471 Fax: (610) 825-2378
www.AAEsports.com
3'-6"42"
(REF)
10'-0"120"
15'-6"186"
Debris Ring(Optional)
If not presentMake sure
lower collarsare positioned
accordingly.
Net Pulley System
RightView
Post Cappre-installed
Lower Horizontal Cable Collarw/ TensionerAssembly
Lower VerticalCable Collarw/ TensionerAssembly(see collar orientationdetail)
Upper VerticalCable CollarAssembly (see collar orientationdetail)
FrontView
40.00°
Collar OrientationDetail
(Note: ONLY vertical cable collars should be turned away from netting)
OpenEyebolt Collar
Detail
CleatDetail
10
89
89
6
7
1
EyeboltDetail
3
4
5
Installation Notes:Lower Collars: From bottom1.of pole slide the lower verticalcable collar, lower horizontalcollar and and debris ring(optional) into position. Toallow proper insertion intoground sleeve, lower mostcollar should be 42" from endof post. Before securing collars into place make sure to rotate the lower vertical collar approx 40°. (refer to diagram)
Cleat: Is to be installed so that2.it is on backside of post,opposite net. Screws will beinserted through cleat and postand secured on net side usingflat washers, Nylock hex-nutsand cap nuts. (refer to diagram)
Mid Collar: Note orientation of3.collar on post. From top of poleslide the open eyebolt collarinto position (refer to diagram) and secure intoplace.
Eyebolt: Pulley system comes4.preassembled to eyebolt.Install washer onto eyeboltthen insert eyebolt with washerthrough front side of hole attop of post. From oppositeside secure eyebolt into placeusing a flatwasher and self-locking hex-nut. (refer to diagram)
Upper Collar: From top of5.pole slide the upper verticalcable collar into position (collarshould rest on eyeboltwashers). Before securing intoplace make sure to rotate thecollar approx 40°. (refer to diagram)
Make sure warning labels are6.present on goal posts.
Note:Post assembly should be done with post laying down on flat level surface.
SBS-25Assembly InstructionLeft End Post
7 of 12
®Aluminum Athletic Equipment
1000 Enterprise Drive, Royersford, PA 19468 Toll Free: (800) 523-5471 Fax: (610) 825-2378
www.AAEsports.com
3'-6"42"
(REF)
Debris Ring(Optional)
If not presentMake sure
lower collarsare positioned
accordingly.
Net Pulley System
RightView
Post Cappre-installed
Lower Horizontal Cable Collarw/ Pear Clip
FrontView
CleatDetail
1
6
7
8
10
8
9
9
Eyebolt Detail
5
4
3
Collar OrientationDetail
Installation Notes:Lower Collars: From bottom1.of pole slide the lower horizontal collar and and debris ring (optional) into position. To allow proper insertion into ground sleeve, lower most collar should be 42" from end of post. Before securing collars into place verify correct orientation. (refer to diagram)
Cleat: Is to be installed so that2.it is on backside of post,opposite net. Screws will beinserted through cleat and postand secured on net side usingflat washers, self locking hex-nuts and cap nuts. (refer to diagram)
Eyebolt: Pulley system comes3.preassembled to eyebolt.Install washer onto eyeboltthen insert eyebolt with washerthrough front side of hole attop of post. From oppositeside secure eyebolt into placeusing a flatwasher and self-locking hex-nut. (refer to diagram)
Upper Collar: From top of4.pole slide the upper verticalcable collar into position (collarshould rest on eyeboltwashers). Before securing collars into place verify correct orientation. (refer to diagram)
Make sure warning labels are5.present on goal posts.
Note:Post assembly should be done with post laying down on flat level surface.
SBS-25Assembly InstructionInner Post
8 of 12
®Aluminum Athletic Equipment
1000 Enterprise Drive, Royersford, PA 19468 Toll Free: (800) 523-5471 Fax: (610) 825-2378
www.AAEsports.com
3'-6"42"
10'-0"120"
15'-6"186"
Lower Horizontal Cable Collarw/ Anchor Shackle for Crimped End Loop
Lower VerticalCable Collarw/ Tensioner
Assembly(see collar orientation
detail)
Upper VerticalCable Collar
Assembly (see collar orientation
detail)
FrontView
Debris Ring(Optional)
If not presentMake sure
lower collarsare positioned
accordingly.
LeftView
Post Cappre-installed
Net Pulley System
40.00°
Collar OrientationDetail
(Note: ONLY vertical cable collars should be turned
away from netting, this aids in tensioning the net)
EyeboltDetail
3
4
5
CleatDetail
10
8
8
6
7
9
9
1
OpenEyebolt Collar
Detail
Installation Notes:Lower Collars: From bottom1.of pole slide the lower verticalcable collar, lower horizontalcollar and and debris ring(optional) into position. Toallow proper insertion intoground sleeve, lower mostcollar should be 42" from endof post. Before securing collars into place make sure to rotate the lower vertical collar approx 40°. (refer to diagram)
Cleat: Is to be installed so2.that it is on backside of post,opposite net. Screws will beinserted through cleat andpost and secured on net sideusing flat washers, selflocking hex-nuts and capnuts. (refer to diagram)
Mid Collar: Note orientation3.of collar on post. From top ofpole slide the open eyeboltcollar into position, refer todimension provided andsecure into place.
Eyebolt: Pulley system4.comes preassembled toeyebolt. Install washer ontoeyebolt then insert eyeboltwith washer through frontside of hole at top of post.From opposite side secureeyebolt into place using aflatwasher and Nylock hex-nut. (refer to diagram)
Upper Collar: From top of5.pole slide the upper verticalcable collar into position(collar should rest on eyeboltwashers). Before securinginto place make sure to rotatethe collar approx 40°. (refer to diagram)
Make sure warning labels are6.present on goal posts.
Note:Post assembly should be done with post laying down on flat level surface.
SBS-25Assembly InstructionRight End Post
9 of 12
®Aluminum Athletic Equipment
1000 Enterprise Drive, Royersford, PA 19468 Toll Free: (800) 523-5471 Fax: (610) 825-2378
www.AAEsports.com
Left End Post
Inner Post
Inner Post
Right End Post
Cleet:Orientation(all posts) away from field of play
Net Hoist:Orientation(all posts) towards field of play
Lower Collars:Orientation(all posts) towards field of play (refer to post assembly pages)
Post / GroundsleeveInstallation (fully seated)
Postwill stop
once it restson stop bolt
After posts have been lowered into place, secure the lower collar(s) into place.
Post / GroundsleeveInstallation
Installation Notes:View above is from net side of post (field 1.of play).
Caution, slowly lower posts into sleeves.2.Dropping post into sleeve may result indamage to the stop bolt.
Make sure all posts are orientated3.correctly. Pulley system towards field ofplay and cleet away from field of play. Alllower horizontal cable collars should facefield of play.
Once posts are correctly orientated, make4.sure the lower collars are properlyorientated and secure them into place.
View from field of Play
Note: Height & number of inner posts may vary from what is shown.
SBS-25Assembly InstructionPosts to Groundsleeve
10 of 12
®Aluminum Athletic Equipment
1000 Enterprise Drive, Royersford, PA 19468 Toll Free: (800) 523-5471 Fax: (610) 825-2378
www.AAEsports.com
View from field of Play
Left End Post(Clamped Loop End)
Inner Post(Pear Clip Collar Assembly)
Pear Clip
Right End Post(Crimped Loop End)
CrimpedCable End
(pre-assembled)
Clamped Loop EndDetail
Thimble(must be present)
Cable Clamp Loopmust be on cut end
of cable
After Cable has been fully tensioned trim cut end and
wrap with electrical tape
Support Cable Vinyl Sleeve must be stripped from cable loop end prior to installing clamps
Support Cable Vinyl Jacket
Installation Notes:Refer to collar assembly diagram for 1.further detail on collar and cable assembly.
Install Crimped Cable End to Right End2.Post collar using an anchor shackle.
Route cable to Left End Post. Snap cable3.into Pear Clips of the Inner Posts alongthe way
Before assembling Clamped Cable Loop4.End, fully open the turnbuckle.
With anchor shackle and thimble inplace5.run cable thru the shackle as shown. Pullslack out of cable and mark vinyl sleeveapproximately 4" from thimble end. Stripvinyl from mark location towards cableloop end.
With the slack still being pulled out of6.cable install and secure the cable clamps.The first clamp should butt upto thethimble, the second should be spacedapprox. 1" on center from the first. Cableclamps must be gripping bare cable toensure proper seating/grip.
SBS-25Assembly InstructionLower Horizontal Support Cable
11 of 12
®Aluminum Athletic Equipment
1000 Enterprise Drive, Royersford, PA 19468 Toll Free: (800) 523-5471 Fax: (610) 825-2378
www.AAEsports.com
A Note: When raising net, it must be done in increments across the entire span
Hoist SystemDetail B
Pear ClipB
Net to End Post Vertical Support Cable
Detail C
Pear ClipsSpaced approx. every 12", entire length of vertical cable (Left and Right End Posts Only)23
22
Brass RingDetail A
B
B
BrassRingTop of net
is bound to a steel
cable
CableClamp
Installation Notes:Lay net on ground across span of posts.1.Make sure net is centered accross span of posts.
Using a Pear Clip Secure upper net2.corners to End Post Vertical SupportCables (as shown in Detail C)
Secure Brass Rings to top of net using3.Cable Clamp (as shown in Detail A).One ring and clamp per post and theyshould be centered as close as possibleto its coinciding post.
After Brass Rings have been secured to4.net, clip ring into it's posts hoist systemPear Clip (as shown in Detail B).
As net is being raised make sure to5.secure net sides to the vertical supportcables using provided Pear Clips (refer to Detail C). Pear Clips should bespaced approx. 12" or 4 net squares.
Once net has been completed raised tie6.hoist ropes onto cleat.
Note: Hardware denoted with "B" is included in item
#3 "Hoist Rope"
SBS-25Assembly InstructionNet Attachment
12 of 12