sapper multiple monitor beam easy order guide€¦ · monitors exceed the sample monitor sizes used...
TRANSCRIPT
Sapper Multiple Monitor Beam Easy Order Guide
Summer 2011
Page 2 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Sapper Multiple Monitor Beam Solutions allow for an
unparalleled level of convenience and style in creating easily
reconfigurable multiple monitor workstations. This guide
provides an overview of the available kits complete with visual
illustrations, pattern codes and suggested uses for mounting
up to 8 monitors.
How to Use This GuideThis easy order guide should help identify the right multiple monitor beam solution and should simplify
the specifying process. The Sapper multiple monitor beam kits can accommodate a variety of monitor
configurations and make monitor reconfiguring easy. This guide is a straightforward tool to help clients find
the right solutions for their needs.
Because of variations in manufacturers’ monitor measurements, in addition to knowing the diagonal screen
measurement, it is critical to have your clients measure the outside dimensions of their monitors. If your client’s
monitors exceed the sample monitor sizes used in this guide, look to the monitor size immediately larger than
your client’s actual monitor.
After choosing a monitor configuration (size, number and orientation) use the chart on page 8 to see which page
to flip to for suggested beam kits.
Page 3 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Single Monitor Beam Solutions
Four Monitor Solution on One Beam
(A)
(B) (C)
Fig. 1
(A)
(B) (C)
Fig. 1
Three Monitor Solution on One Beam
Portrait* Landscape
Small (50") 31.6" 21.2"
Medium (64") 44" 28"
Large (76") 44" 34.2"
MAXIMUM MONITOR SIZE
BE
AM
SIZ
E
Portrait* Landscape
Small (50") 21.2" 14"
Medium (64") 26.4" 18.8"
Large (76") 44" 23"
MAXIMUM MONITOR SIZE
BE
AM
SIZ
E
Assumes use of a 24" mast for additional clearance under monitors.
Note: The monitor measurements for these drawings are by width and height, not diagonal, and are based on actual monitor sizes. Actual
monitor dimensions may vary.
*
Page 4 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
(A)
(B) (C)
Fig. 1
Six Monitor Solution on Two Beams
(A)
(B) (C)
Fig. 1
Eight Monitor Solution on Two Beams
Double Monitor Beam Solutions
Portrait Landscape
Small (50") 19.9" 21.2"
Medium (64") 19.9" 28"
Large (76") 19.9" 34.2"
MAXIMUM MONITOR SIZE
BE
AM
SIZ
E
Portrait Landscape
Small (50") 19.9" 14"
Medium (64") 19.9" 18.8"
Large (76") 19.9" 23"
MAXIMUM MONITOR SIZE
BE
AM
SIZ
E
Note: The monitor measurements for these drawings are by width and height, not diagonal, and are based on actual monitor sizes. Actual
monitor dimensions may vary.
Page 5 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
(A)
(B) (C)
Fig. 1
Worksurface Space Requirements for
Multiple Monitor Beam Solutions
MOUNTING OPTION
Beam Length (A)
Heavy-Duty Table Clamp (B)
Antenna Center Beam Side Mount (C)
50" 40" 43.5"
64" 44.5" 48"
76" 44.5" 48"
Worksurface Space Needed For:
Page 6 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Multiple Monitor Beam Solutions: ExamplesHere are some examples of how the Multiple Monitor Beam Solutions can meet your clients’ needs.
Application: Trading floor at a hedge fund
Solution: Small (50") beams with 3 monitors mounted with Antenna Workspaces center beam side mounts.
Application: Security room at a university
Solution: Double large (76") beam with 8 monitors, mounted on AutoStrada with heavy duty table clamps.
Page 7 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
How to Order a Multiple Monitor Beam Kit
Explanation of the Knoll order code, for example SAP B 16 M 6 ANT SIDE K
SAP Sapper Monitor Arm Collection
B Multiple Monitor Beam Solutions
16 Mast height – masts come in 16", 24" and 32"
M Beam size – beams come in small (50"), medium (64") or large (76")
6 Number of movement joint slides needed for monitors – kits accommodate 3, 4, 6 or 8 monitors
ANT The type of mount provided with the kit – the ANT SIDE K mount secures the beam to the side of the
Antenna center beam (clearing the flip door and screens), whereas the CLMP HD K (heavy-duty clamp)
mount secures the beam to most other worksurfaces
*Note: All parts are also available 'a la carte' to accommodate additional monitors as well as changing needs.
SIDE K
Page 8 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Monitor Beam Kit Ordering OptionsN
UM
BE
R O
F M
ON
ITO
RS
SIZE OF MONITORS (measured diagonally – actual dimensions of sample monitors listed below)
19” 20” 22” 24” 28” 30” 32”
12.4” x 17.8 12.4” x 19.2” 13.3” x 20.6” 17” x 22.9” 19.25” x 26.4” 19.4” x 27.6” 19.4” x 31.6”
3 Landscape
p. 9
Landscape
p. 10
Landscape
p. 11
Landscape
p. 12
Landscape
p. 13
Landscape
p. 14
Landscape
p. 15
Portrait p. 16 Portrait p. 17 Portrait p. 18 Portrait p. 19 Portrait p. 20 Portrait p. 21 Portrait p. 22
4 Landscape
p. 23
Landscape
p. 24
Landscape
p. 25
Landscape
p. 26
Landscape
n/a
Landscape
n/a
Landscape
n/a
Portrait p. 27 Portrait p. 28 Portrait p. 29 Portrait p. 30 Portrait p. 31 Portrait p. 32 Portrait p. 33
6 Landscape
p. 34
Landscape
p. 35
Landscape
p. 36
Landscape
p. 37
Landscape
p. 38
Landscape
p. 39
Landscape
p. 40
Portrait p. 41 Portrait p. 42 Portrait 43 Portrait n/a Portrait n/a Portrait n/a Portrait n/a
8 Landscape
p. 44
Landscape
p. 45
Landscape
p. 46
Landscape
p. 47
Landscape
n/a
Landscape
n/a
Landscape
n/a
Portrait p. 48 Portrait p. 49 Portrait n/a Portrait n/a Portrait n/a Portrait n/a Portrait n/a
*Note: Suggested beam kit shown is minimum size beam and mast required for the number and size of monitors. Each option shown can also be accommodated by larger beams – they will take up additional worksurface space but will also provide additional flexibility.
All parts are also available ‘a la carte’ to accommodate additional monitors as well as changing needs.
Page 9 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Three 19" Monitors in Landscape
Suggested beam kits
SAP B 16 S 3 ANT SIDE K
SAP B 16 S 3 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Three movement joint slides
• One 50" beam
• Two beam mast cable management clips
• Six beam cable management clips
• Two mounts (either Antenna center beam
side mounts or heavy-duty table clamp mounts)
52.73[1339]
to work surface
8.34212[ ]
12.17[309]
12.40[315]
17.80[452]
50.12[1273]
2.50[64]
SAP B 16 S 319" monitors in landscape
rd 23may2011
A
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 12.4"H by 17.8"W.
Page 10 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Three 20" Monitors in Landscape
56.70[1440]
to work surface
8.34212[ ]
12.90[328]
12.40[315]
19.20[488]
50.12[1273]
2.50[64]
SAP B 16 S 320" monitors in landscape
rd 23may2011
A
Suggested beam kits
SAP B 16 S 3 ANT SIDE K
SAP B 16 S 3 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Three movement joint slides
• One 50" beam
• Two beam mast cable management clips
• Six beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 12.4"H by 19.2"W.
Sapper Multiple Monitor Beam Easy Order Guide
Summer 2011
Page 12 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
67.06[1703]
to work surface
6.07154[ ]
14.65[372]
17.00[432]
22.90[582]
64.22[1631]
2.60[66]
SAP B 16 M 324" monitors in landscape
rd 05apr2011
A
Three 24" Monitors in Landscape
Suggested beam kits
SAP B 16 M 3 ANT SIDE K
SAP B 16 M 3 CLMP HD K
Space requirements
• 64" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Three movement joint slides
• One 64" beam
• Two beam mast cable management clips
• Eight beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 17"H by 22.9"W.
Page 13 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Three 28" Monitors in Landscape
76.38[1940]
to work surface
4.91125[ ]
17.88[454]
19.25[489]
26.40[671]
64.22[1631]
3.38[86]
SAP B 16 M 328" monitors in landscape
rd 06apr2011
A
Suggested beam kits
SAP B 16 M 3 ANT SIDE K
SAP B 16 M 3 CLMP HD K
Space requirements
• 64" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Three movement joint slides
• One 64" beam
• Two beam mast cable management clips
• Eight beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 19.25"H by 26.4"W.
Page 14 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Three 30" Monitors in Landscape
79.41[2017]
to work surface
12.87327[ ]
19.34[491]
19.40[493]
27.60[701]
76.21[1936]
3.90[99]
SAP B 24 L 330" monitors in landscape
rd 31mar2011
A
Suggested beam kits
SAP B 16 L 3 ANT SIDE K
SAP B 16 L 3 CLMP HD K
Space requirements
• 76" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Three movement joint slides
• One 76" beam
• Two beam mast cable management clips
• Ten beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 19.4"H by 27.6"W.
Page 15 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Three 32" Monitors in Landscape
89.28[2268]
to work surface
12.87327[ ]
22.47[571]
19.40[493]
31.60[803]
76.21[1936]
3.90[99]
SAP B 24 L 332" monitors in landscape
rd 31mar2011
A
Suggested beam kits
SAP B 24 L 3 ANT SIDE K
SAP B 24 L 3 CLMP HD K
Space requirements
• 76" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 24" masts
• Three movement joint slides
• One 76" beam
• Two beam mast cable management clips
• Ten beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 19.4"H by 31.6"W.
Page 16 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Three 19" Monitors in Portrait
Suggested beam kits
SAP B 16 S 3 ANT SIDE K
SAP B 16 S 3 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Three movement joint slides
• One 50" beam
• Two beam mast cable management clips
• Six beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
to worksurf5.71145[ ]
37.21[945,1]
50.10[1272,6]
12.40[315]
2.50[63,5]
9.53[242]
17.80[452,1]
A
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 17.8"H by 12.4"W.
Page 17 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Three 20" Monitors in Portrait
to worksurf5.01127,2[ ]
37.21[945,1]
50.10[1272,6]
12.40[315]
2.50[63,5]
9.53[242]
19.20[487,7]
SAP B 16 S 320" monitors in portrait
rd 17may2010
A
Suggested beam kits
SAP B 16 S 3 ANT SIDE K
SAP B 16 S 3 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Three movement joint slides
• One 50" beam
• Two beam mast cable management clips
• Six beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 19.2"H by 12.4"W.
Page 18 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Three 22" Monitors in Portrait
Suggested beam kits
SAP B 16 S 3 ANT SIDE K
SAP B 16 S 3 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Three movement joint slides
• One 50" beam
• Two beam mast cable management clips
• Six beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
to worksurf4.31109,4[ ]
39.84[1012]
50.10[1272,6]
13.30[337,8]
2.50[63,5]
9.85[250,3]
20.60[523,2]
SAP B 16 S 322" monitors in portrait
rd 17may2010
A
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 20.6"H by 13.3"W.
Page 19 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Three 24" Monitors in Portrait
Suggested beam kits
SAP B 16 S 3 ANT SIDE K
SAP B 16 S 3 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Three movement joint slides
• One 50" beam
• Two beam mast cable management clips
• Six beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
to worksurf3.1680,2[ ]
50.55[1283,9]
50.10[1272,6]
17.00[431,8]
2.60[66]
11.54[293,2]
22.90[581,7]
SAP B 16 S 324" monitors in portrait
rd 17may2010
A
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 22.9"H by 17"W.
Page 20 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Three 28" Monitors in Portrait
Suggested beam kits
SAP B 16 S 3 ANT SIDE K
SAP B 16 S 3 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Three movement joint slides
• One 50" beam
• Two beam mast cable management clips
• Six beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
to worksurf1.4135,8[ ]
56.85[1443,9]
50.10[1272,6]
19.25[489]
3.38[85,7]
13.50[342,9]
26.40[670,6]
SAP B 16 S 328" monitors in portrait
rd 17may2010
A
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 26.4"H by 19.25"W.
Page 21 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Three 30" Monitors in Portrait
Suggested beam kits
SAP B 16 S 3 ANT SIDE K
SAP B 16 S 3 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Three movement joint slides
• One 50" beam
• Two beam mast cable management clips
• Six beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
to worksurf.8120,5[ ]
57.34[1456,4]
50.10[1272,6]
19.40[492,8]
3.90[99,1]
14.16[359,7]
27.60[701]
SAP B 16 S 330" monitors in portrait
rd 17may2010
A
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 27.6"H by 19.4"W.
Page 22 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Three 32" Monitors in Portrait
Suggested beam kits
SAP B 24 S 3 ANT SIDE K
SAP B 24 S 3 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 24" masts
• Three movement joint slides
• One 50" beam
• Two beam mast cable management clips
• Six beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
to worksurf6.81172,9[ ]
57.34[1456,4]
50.10[1272,6]
19.40[492,8]
3.90[99,1]
14.16[359,7]
31.60[802,6]
SAP B 24 S 332" monitors in portrait
rd 17may2010
A
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 31.6"H by 19.4"W.
Page 23 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Four 19" Monitors in Landscape
Suggested beam kits
SAP B 16 M 4 ANT SIDE K
SAP B 16 M 4 CLMP HD K
Space requirements
• 64" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Four movement joint slides
• One 64" beam
• Two beam mast cable management clips
• Eight beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
to worksurf8.41213,6[ ]
69.09[1754,8]
64.20[1630,7]
17.80[452,1]
2.50[63,5]
15.13[384,2]
12.40[315]
SAP B 16 M 419" monitors in landscape
rd 13may2010
A
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 12.4"H by 17.8"W.
Page 24 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Suggested beam kits
SAP B 16 L 4 ANT SIDE K
SAP B 16 L 4 CLMP HD K
Space requirements
• 76" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Four movement joint slides
• One 76" beam
• Two beam mast cable management clips
• Ten beam cable management clips
• Two mounts (either Antenna center beam side
mounts or heavy-duty table clamp mounts)
Four 20" Monitors in Landscape
74.10[1882]
to work surface
8.37213[ ]
16.83[428]
12.40[315]
19.20[488]
76.21[1936]
SAP B 16 L 420" monitors in landscape
rd 30mar2011
A
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 12.4"H by 19.2"W.
Page 25 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Four 22" Monitors in Landscape
Suggested beam kits
SAP B 16 L 4 ANT SIDE K
SAP B 16 L 4 CLMP HD K
Space requirements
• 76" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Four movement joint slides
• One 76" beam
• Two beam mast cable management clips
• Ten beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
78.98[2006]
to work surface
7.92201[ ]
18.26[464]
13.30[338]
20.60[523]
76.21[1936]
SAP B 16 L 422" monitors in landscape
rd 29mar2011
A
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 13.3"H by 20.6"W.
Page 26 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Four 24" Monitors in Landscape
86.57[2199]
to work surf
6.07154[ ]
20.85[530]
17.00[432]
22.90[582]
76.21[1936]
SAP B 16 L 424" monitors in landscape
rd 28mar2011
A
Suggested beam kits
SAP B 16 L 4 ANT SIDE K
SAP B 16 L 4 CLMP HD K
Space requirements
• 76" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Four movement joint slides
• One 76" beam
• Two beam mast cable management clips
• Ten beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 17"H by 22.9"W.
Page 27 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Four 19" Monitors in Portrait
to worksurf5.71145[ ]
49.24[1250,7]
50.10[1272,6]
12.40[315] 2.50
[63,5]
11.44[290,6]
17.80[452,1]
SAP B 16 S 419" monitors in portrait
rd 13may2010
A
Suggested beam kits
SAP B 16 S 4 ANT SIDE K
SAP B 16 S 4 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Four movement joint slides
• One 50" beam
• Two beam mast cable management clips
• Six beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 17.8"H by 12.4"W.
Page 28 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Four 20" Monitors in Portrait
to worksurf5.01127,2[ ]
49.24[1250,7]
50.10[1272,6]
12.40[315] 2.50
[63,5]
11.44[290,6]
19.20[487,7]
SAP B 16 S 420" monitors in portrait
rd 13may2010
A
Suggested beam kits
SAP B 16 S 4 ANT SIDE K
SAP B 16 S 4 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Four movement joint slides
• One 50" beam
• Two beam mast cable management clips
• Six beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 19.2"H by 12.4"W.
Page 29 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Four 22" Monitors in Portrait
to worksurf4.31109,4[ ]
52.66[1337,7]
50.10[1272,6]
13.30[337,8] 2.50
[63,5]
12.05[306,1]
20.60[523,2]
SAP B 16 S 422" monitors in portrait
rd 13may2010
A
Suggested beam kits
SAP B 16 S 4 ANT SIDE K
SAP B 16 S 4 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Four movement joint slides
• One 50" beam
• Two beam mast cable management clips
• Six beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 20.6"H by 13.3"W.
Page 30 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Four 24" Monitors in Portrait
to worksurf11.16283,4[ ]
66.22[1682,1]
64.20[1630,7]
17.00[431,8]
2.60[66]
14.52[368,9]
22.90[581,7]
SAP B 24 M 424" monitors in portrait
rd 14may2010
A
Suggested beam kits
SAP B 24 M 4 ANT SIDE K
SAP B 24 M 4 CLMP HD K
Space requirements
• 64" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 24" masts
• Four movement joint slides
• One 64" beam
• Two beam mast cable management clips
• Eight beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 22.9"H by 17"W.
Page 31 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Four 28" Monitors in Portrait
74.38[1889]
to work surface
1.3735[ ]
17.91[455]
26.40[671]
19.25[489]
76.21[1936]
3.38[86]
SAP B 16 L 428" monitors in portrait
rd 31mar2011
A
Suggested beam kits
SAP B 16 L 4 ANT SIDE K
SAP B 16 L 4 CLMP HD K
Space requirements
• 76" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 16" masts
• Four movement joint slides
• One 76" beam
• Two beam mast cable management clips
• Ten beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 26.4"H by 19.25"W.
Page 32 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Four 30" Monitors in Portrait
Suggested beam kits
SAP B 24 L 4 ANT SIDE K
SAP B 24 L 4 CLMP HD K
Space requirements
• 76" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 24" masts
• Four movement joint slides
• One 76" beam
• Two beam mast cable management clips
• Ten beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
74.89[1902]
to work surface
8.77223[ ]
18.66[474]
27.60[701]
19.40[493]
76.21[1936]
3.90[99]
SAP B 24 L 430" monitors in portrait
rd 31mar2011
A
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 27.6"H by 19.4"W.
Page 33 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Four 32" Monitors in Portrait
74.89[1902]
to work surface
6.77172[ ]
18.66[474]
31.60[803]
19.40[493]
76.21[1936]
3.90[99]
SAP B 24 L 432" monitors in portrait
rd 31mar2011
A
Suggested beam kits
SAP B 24 L 4 ANT SIDE K
SAP B 24 L 4 CLMP HD K
Space requirements
• 76" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 24" masts
• Four movement joint slides
• One 76" beam
• Two beam mast cable management clips
• Ten beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 31.6"H by 19.4"W.
Page 34 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Six 19" Monitors in Landscape
Suggested beam kits
SAP B 32 S 6 ANT SIDE K
SAP B 32 S 6 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Six movement joint slides
• Two 50" beams
• Four beam mast cable management clips
• Twelve beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
to worksurf11.95303,5[ ]
52.73[1339,3]
50.10[1272,6]
17.80[452,1]
2.50[63,5]
11.81[299,9]
12.40[315]
SAP B 32 S 619" monitors in landscape
rd 06may2010
A
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 12.4"H by 17.8"W.
Page 35 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Six 20" Monitors in Landscape
56.70[1440]
to work surface
11.83301[ ]
12.90[328]
12.40[315]
19.20[488]
50.12[1273]
2.50[64]
SAP B 32 S 620" monitors in landscape
rd 24may2011
A
Suggested beam kits
SAP B 32 S 6 ANT SIDE K
SAP B 32 S 6 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Six movement joint slides
• Two 50" beams
• Four beam mast cable management clips
• Twelve beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 12.4"H by 19.2"W.
Page 36 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Six 22" Monitors in Landscape
60.74[1543]
to work surface
10.48266[ ]
13.70[348]
13.30[338]
20.60[523]
50.12[1273]
2.50[64]
SAP B 32 S 622" monitors in landscape
rd 24may2011
A
Suggested beam kits
SAP B 32 S 6 ANT SIDE K
SAP B 32 S 6 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Six movement joint slides
• Two 50" beams
• Four beam mast cable management clips
• Twelve beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 13.3"H by 20.6"W.
Page 37 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Six 24" Monitors in Landscape
67.06[1703]
to work surface
4.93125[ ]
14.65[372]
17.00[432]
22.90[582]
64.22[1631]
2.60[66]
SAP B 32 M 624" monitors in landscape
rd 24may2011
A
Suggested beam kits
SAP B 32 M 6 ANT SIDE K
SAP B 32 M 6 CLMP HD K
Space requirements
• 64" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Six movement joint slides
• Two 64" beams
• Four beam mast cable management clips
• Sixteen beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 17"H by 22.9"W.
Page 38 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Six 28" Monitors in Landscape
76.38[1940]
to work surface
1.5640[ ]
17.88[454]
19.25[489]
26.40[671]
64.22[1631]
3.38[86]
SAP B 32 M 628" monitors in landscape
rd 24may2011
A
Suggested beam kits
SAP B 32 M 6 ANT SIDE K
SAP B 32 M 6 CLMP HD K
Space requirements
• 64" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Six movement joint slides
• Two 64" beams
• Four beam mast cable management clips
• Sixteen beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 19.25"H by 26.4"W.
Page 39 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Six 30" Monitors in Landscape
79.41[2017]
to work surface
1.3334[ ]
19.34[491]
19.40[493]
27.60[701]
76.21[1936]
3.90[99]
SAP B 32 L 630" monitors in landscape
rd 30mar2011
A
Suggested beam kits
SAP B 32 L 6 ANT SIDE K
SAP B 32 L 6 CLMP HD K
Space requirements
• 76" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Six movement joint slides
• Two 76" beams
• Four beam mast cable management clips
• Twenty beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 19.4"H by 27.6"W.
Page 40 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Six 32" Monitors in Landscape
89.28[2268]
to work surface
1.3334[ ]
22.47[571]
19.40[493]
31.60[803]
76.21[1936]
3.90[99]
SAP B 32 L 632" monitors in landscape
rd 30mar2011
A
Suggested beam kits
SAP B 32 L 6 ANT SIDE K
SAP B 32 L 6 CLMP HD K
Space requirements
• 76" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Six movement joint slides
• Two 76" beams
• Four beam mast cable management clips
• Twenty beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 19.4"H by 31.6"W.
Page 41 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Six 19" Monitors in Portrait
37.21[945]
to work surface
3.7395[ ]
9.89[251]
17.80[452]
12.40[315]
50.12[1273]
2.50[64]
SAP B 32 S 619" monitors in portrait
rd 24may2011
A
Suggested beam kits
SAP B 32 S 6 ANT SIDE K
SAP B 32 S 6 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Six movement joint slides
• Two 50" beams
• Four beam mast cable management clips
• Twelve beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 17.8"H by 12.4"W.
Page 42 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Six 20" Monitors in Portrait
to worksurf1.7143,5[ ]
37.21[945,1]
50.10[1272,6]
12.40[315] 2.50
[63,5]
9.53[242]
19.20[487,7]
SAP B 32 S 620" monitors in portrait
rd 06may2010
A
Suggested beam kits
SAP B 32 S 6 ANT SIDE K
SAP B 32 S 6 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Six movement joint slides
• Two 50" beams
• Four beam mast cable management clips
• Twelve beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 19.2"H by 12.4"W.
Page 43 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Six 22" Monitors in Portrait
below worksurf.348,6[ ]
39.84[1012]
50.10[1272,6]
13.30[337,8] 2.50
[63,5]
9.85[250,3]
20.60[523,2]
SAP B 32 S 622" monitors in portrait
rd 06may2010
Some brands of 22" monitorsmay fit in this configuration.LG W2253-TQPF shown.
A
Suggested beam kits
SAP B 32 S 6 ANT SIDE K
SAP B 32 S 6 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Six movement joint slides
• Two 50" beams
• Four beam mast cable management clips
• Twelve beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 20.6"H by 13.3"W.
Page 44 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Eight 19" Monitors in Landscape
Suggested beam kits
SAP B 32 M 8 ANT SIDE K
SAP B 32 M 8 CLMP HD K
Space requirements
• 64" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Eight movement joint slides
• Two 64" beams
• Four beam mast cable management clips
• Sixteen beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
69.35[1762]
to work surface
11.83301[ ]
15.56[395]
12.40[315]
17.80[452]
64.22[1631] SAP B 32 M 8
19" monitors in landscaperd 05apr2011
A
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 12.4"H by 17.8"W.
Page 45 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
74.10[1882]
to work surface
11.83301[ ]
16.83[428]
12.40[315]
19.20[488]
76.21[1936] SAP B 32 L 8
20" monitors in landscaperd 30mar2011
Eight 20" Monitors in Landscape
A
Suggested beam kits
SAP B 32 L 8 ANT SIDE K
SAP B 32 L 8 CLMP HD K
Space requirements
• 76" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Eight movement joint slides
• Two 76" beams
• Four beam mast cable management clips
• Twenty beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 12.4"H by 19.2"W.
Page 46 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Eight 22" Monitors in Landscape
78.98[2006]
to work surface
10.48266[ ]
18.26[464]
13.30[338]
20.60[523]
76.21[1936]
SAP B 32 L 822" monitors in landscape
rd 30mar2011
A
Suggested beam kits
SAP B 32 L 8 ANT SIDE K
SAP B 32 L 8 CLMP HD K
Space requirements
• 76" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Eight movement joint slides
• Two 76" beams
• Four beam mast cable management clips
• Twenty beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 13.3"H by 20.6"W.
Page 47 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Eight 24" Monitors in Landscape
86.57[2199]
to work surface
4.93125[ ]
20.85[530]
17.00[432]
22.90[582]
76.21[1936]
SAP B 32 L 824" monitors in landscape
rd 29mar2011
A
Suggested beam kits
SAP B 32 L 8 ANT SIDE K
SAP B 32 L 8 CLMP HD K
Space requirements
• 76" of workspace
• (A) = amount of linear desk space needed from
mount to mount (44.02" with heavy-duty clamps
and 47.27" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Eight movement joint slides
• Two 76" beams
• Four beam mast cable management clips
• Twenty beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 17"H by 22.9"W.
Page 48 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Eight 19" Monitors in Portrait
49.24[1251]
to work surface
3.7796[ ]
11.80[300]
17.80[452]
12.40[315]
50.12[1273]
2.50[64]
SAP B 32 S 819" monitors in portrait
rd 24may2011
A
Suggested beam kits
SAP B 32 S 8 ANT SIDE K
SAP B 32 S 8 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Eight movement joint slides
• Two 50" beams
• Four beam mast cable management clips
• Twelve beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 17.8"H by 12.4"W.
Page 49 Sapper Multiple Monitor Beam Easy Order Guide
August 2011 © 2011 Knoll, Inc.
Eight 20" Monitors in Portrait
49.24[1251]
to work surface
1.6342[ ]
11.80[300]
19.20[488]
12.40[315]
50.12[1273]
2.50[64]
SAP B 32 S 820" monitors in portrait
rd 03apr2011
A
Suggested beam kits
SAP B 32 S 8 ANT SIDE K
SAP B 32 S 8 CLMP HD K
Space requirements
• 50" of workspace
• (A) = amount of linear desk space needed from
mount to mount (39.92" with heavy-duty clamps
and 43.5" with Antenna center beam side mount)
Kits include
• Two 32" masts
• Eight movement joint slides
• Two 50" beams
• Four beam mast cable management clips
• Twelve beam cable management clips
• Two mounts (either Antenna center beam side mounts
or heavy-duty table clamp mounts)
Actual dimensions of monitors can vary and depending on monitor choice, some may extend beyond either side of the beam assembly. Maximum weight for each monitor is 20 pounds. Actual monitor size used in drawings: 19.2"H by 12.4"W.