saib rifles & carbines with ars

8/7/2019 SAIB Rifles & Carbines with ARS

1/104

The Soldier: Americas Most Deployed Combat System

1. Upon entering the site you will be asked to select your weapon. Click on thepicture of your weapon

2. You will then be taken to a page with pictures of your selected weapon, with avariety of devices, and/or multiple device configurations. Click on the picture of theweapon and devices for which you wish to obtain information.

3. You will be taken to pages that contain mounting instructions, with supportingdiagrams, and a Bore Sight Offset target.

a. You may review the data, printing those items of information that you desire.

NOTE

When printing the Bore Sight Offset Targets insure that the printer margins are set to.25 inches, Top, Bottom, Left and Right. These targets are properly proportioned to

be used directly in the bore sighting of your weapons and devices.b. Once you have finished reviewing the information you may select the

Return to Weapon Selection button to make additional choices.

NOTE: All references contained in the following pages pertain to the Small ArmsIntegration Book, dated January, 2006

Project Manager Soldier WeaponsSmall Arms Integration Book

Rifles & Carbines Equipped with Adapter Rail System

ENTER


2/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 2

Click On Your Weapon

M203A2(On M4/M4A1

Carbine w/M4 ARS)

M4/M4A1 Carbinewith M4 Adapter Rail

System

M16A4 Rifle withM5 Adapter Rail

System

M203A2(On M16A4 w/M5 ARS)



Select Your M16A4 Rifle w/M5 Adapter Rail System & Device Combination(Page 1 of 5)

Click for AdditionalConfigurations

(Pictures Not to Scale)






AN/PAQ-4C Using

Mounting Bracket/Picatinny RailGrabber






AN/PAQ-4C UsingInsight Low

Profile RailGrabber




Click to Return toWeapon Selection



Select Your M203A2 Grenade LauncherMounted on M16A4 w/M5 ARS & Device Combination




Select Your M4 Carbine w/M4 Adapter Rail System & Device Combination(Page 1 of 5)








M4/M4A1 & M4 ARS withAN/PAQ-4C & AN/PAS-13A/B(V)1/3

MTD

AN/PAQ-4C UsingMounting Bracket/

Picatinny Rail Grabber






M4/M4A1 & M4 ARS withAN/PAQ-4C & AN/PAS-13A/B(V)1/3

MTD

AN/PAQ-4C UsingInsight Low Profile Rail

Grabber



Select Your M203A2 Grenade LauncherMounted on M4/M4A1 w/M4 ARS & Device Combination


Click to Return to

Weapon Selection



M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber

NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If however

the device is removed from the rail the operator must take note of the position at which the device waszeroed, and return the device to that same position in order to insure that zero is retained.

Target offsets required to properly zero the device to the weapon are as follows:

25m Fired Zero Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.5 Squares Right, 8.0 Squares Up- Top Rail: 1.7 Squares Right, 0.7 Squares Down- Right Side Rail Mounting: 5.9 Squares Left, 3.5 Squares Up

10m Boresight Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.0 cm Left, 4.3 cm Down- Top: 1.8 cm Left, 3.9 cm Up

- Right Side Rail Mounting: 6.0 cm Right, 0.9 cm DownSee Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.

The AN/PAQ-4C may be mounted on the left, top orright side rails using the Mounting Bracket/Picatinny Rail Grabber (NSN 5340-01-458-0473)depicted in the diagram at left.

WARNINGMake sure the weapon is CLEAR and on SAFE

before proceeding.

1. Attach the Mounting Bracket/Picatinny RailGrabber(1) to the AN/PAQ-4C (2) using thethumbscrew on the AN/PAQ-4C.

2. Loosen the clamping knob until the railgrabber/mount has sufficient space to fit over the leftside rail (3). Tighten the clamping knob until two clicksare heard.

3. Install the remote switch in a convenient locationusing the provided cable hangers.

Click for BoreSight Target


16/104

10m Bore Sight Target for 300m Zero--(14 Dec 2001)

10m Boresight M4/M16A4 MWSAN/PAQ-4C Using MountingBracket/Picatinny Rail Grabber

AN/PAQ-4B/CLeft Rail

6.0L/4.3D

AN/PAQ-4B/CTop Rail1.8L/3.9U

AN/PAQ-4B/CRight Rail6.0R/0.9D

Laser Bore Light0/0


Bore Sighting the AN/PAQ-41. Stabilize Weapon.2. Align Laser Borelight on its dot (See Annex F)3. Adjust Device until aiming laser is centered on the dot-cross hair.

Turn off Printer Scaling



M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber

The Aiming Light is mounted on the front left-hand railusing the Insight rail grabber bracket (NSN 5340-01-458-0990) when it is desired to keep the Aiming Lightas close as possible to the barrel.


before proceeding.

1. For ease of installation install the grabber on therail first, then mount the device on the grabber.

2. Loosen the clamping knob (1) until the rail grabberhas sufficient space to fit over the left side rail (2).Hand Tighten the clamping knob (1).

3. Turn the ON/OFF Switch CCW to the #1OFF/STORAGE position.

4. Position the Aiming Light on the bracket mounting rail. Hand tighten the Thumbscrew (3) to secure the AimingLight.

5. Install the remote switch (not shown) in a convenient location using the provided cable hangers.

NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If howeverthe device is removed from the rail the operator must take note of the position at which the device was zeroed,

and return the device to that same position in order to insure that zero is retained.

Target offsets required to properly zero the device to the weapon are as follows

25m Fired Zero Offsets:

- Left Side Rail Mounting: 4.2 Squares Right; 8.6 Squares Up- Top Rail Mounting: 1.7 Squares Right; 1.8 Squares Up- Right Side Rail Mounting: 4.3 Squares Left; 3.4 Squares Up

10m Boresight Offsets:

- Left Side Rail Mounting: 4.3 cm Left; 4.2cm Down- Top Rail Mounting: 1.8 cm Left; 2.2 cm Up- Right Side Rail Mounting: 4.3 cm Right; .7 cm Down

See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.

See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.



18/104


10m Boresight M4/M16A4 MWSAN/PAQ-4C UsingInsight Low Profile Rail Grabber

AN/PAQ-4B/CLeft Rail4.3L/4.2D



Laser Bore Light0/0


ore Sighting the AN/PAQ-4. Stabilize Weapon.. Align Laser Borelight on its dot (See Annex F) Adjust Device until aiming laser is centered on the dot-cross hair.




M4/M16A4 MWSAN/PAS-13A/B(V)1/3 L/HWTS

(See Annex B for Target Prep Instructions)

Install the AN/PAS-13(V)1 on the Modular WeaponSystem (2) using the sights rail grabber/mount (NSN

1240-01-490-0737, Part No. A3281312-1) (3).

NOTE

Procedures outlined below pertain to either M4 or M4A1variants.

NOTE

Although the AN/PAS-13(v)1, LWTS is depicted both theAN/PAS-A/B(V)2 or (V)3 M/HWTS may also be mountedon the weapon using the same methods described below.In order to mount the AN/PAS-A/B(V)2 or (V)3 M/HWTSthe unit armorer must first install a Spacer Kit, M4 (NSN

5340-01-502-7971) to the TWS.

WARNINGMake sure the weapon is CLEAR and on SAFE before proceeding.

1. Remove carrying handle (not shown) from rail (4) of weapon. Retain carrying handle.

2. Loosen the clamping knob (5) until the jaws move far enough apart to fit over the rail (4).

3. Select a slot on rail. Any slot may be used as long as rail grabber/mount does not hang over edge of rail. If the

TWS is removed from the rail the operator must note the position at which the device was zeroed, and return thedevice to that position in order to retain zero.

4. Place rail grabber/mount on rail and tighten clamping knob (5) until two clicks are heard.


25m Fired Zero Offsets:- AN/PAS-13B(v)1 (LWTS): 0.0 Squares Left/Right; 4.5 Squares Down- AN/PAS-13A/B(V)3 (HWTS): 0.0 Squares Left/Right; 6.0 Squares Down


- AN/PAS-13B(v)1 (LWTS): 0.0 cm Left/Right; 7.9 cm Up- AN/PAS-13A/B(V)3 (HWTS): 0.0 cm Left/Right; 9.4 cm Up

See Annex BSIGHT/ACCESSORY OPERATING INSTRUCTIONS for instructions on preparation of AN/PAS-13 targets.

See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.



20/104



M4/M16A4 MWSAN/PEQ-2A Using Insight Low Profile Rail Grabber

The AN/PEQ-2A (1) is mounted on the front left, top, orright rail (2) using the Insight Rail Grabber Bracket

(NSN 5340-01-458-0990) (3).


before proceeding.

1. Mount the rail grabber to the AN/PEQ-2A using thethumbscrew (4) as shown.

2. Loosen the clamping knob (5) on the rail grabberuntil the rail grabber has sufficient space to fit over theleft side rail.

3. Position and tighten the Rail Grabber by turning theknob clockwise.


he device is removed from the rail the operator must take note of the position at which the device was zeroed, andreturn the device to that same position in order to insure that zero is retained.



- Left Side Rail Mounting: 5.0 Squared Right; 4.0 Squares Up- Top Rail Mounting: 2.0 Squares Left; 1.2 Squared Up- Right Side Rail Mounting: 0.5 Squares Left; 8.5 Squares Up


- Left Side Rail Mounting:Aiming: 4.5 cm Left; 1.0 cm DownFlood: 4.5 cm Left; 5.0 cm Down

- Top Rail Mounting:

Aiming: 2.0 cm Right; 2.3 cm UpFlood: 2.0 cm Left; 2.3 cm Up- Right Side Rail Mounting:

Aiming: 4.5 cm Right; 4.4 cm DownFlood: 4.5 cm Right; 0.4 cm Down


Click for Bore

Sight Target


22/104


10m Boresight M4/M16A4 MWSAN/PEQ-2A Using Insight Low ProfileRail Grabber

Laser Bore Light0/0

AN/PEQ-2A AimLeft Rail4.5L/1.0D

AN/PEQ-2A Flood

Left Rail4.5L/5.0D

AN/PEQ-2A FloodTop Rail2.0L/2.3U

AN/PEQ-2A AimTop Rail

2.0R/2.3U

ore Sighting the AN/PEQ-2. Stabilize Weapon.. Align Laser Borelight on its dot (See Annex F). Adjust Device until aiming laser is centered on the dot-cross hair.. Adjust AN/PEQ-2A Flood Light until the laser is centered on the designated dot.


AN/PEQ-2A Aim

Right Rail4.5R, 4.4D

AN/PEQ-2A FloodRight Rail4.5R/0.4D




M4/M16A4 MWSAN/PVS-4A

To mount the AN/PVS-4A to the MWS the unitArmorer must install a spacer (NSN 5365-01-

447-8991) and a rail grabber/mount (NSN 5340-01-449-8533).

1. Loosen two knobs (1) on carrying handle(2). Remove carrying handle from upperreceiver rail (3). Retain carrying handle.

2. Install spacer (5) on AN/PVS-4A (7) usingthe two screws provided. Attach railgrabber/mount (6) to the spacer (5) using thetwo screws provided. (Pre-assembled by UnitArmorer.)

3. Loosen the clamping knob (8) until sufficientspace exists to place the clamping jaws oneither side of the mounting rail (3). Tightenclamping knob (8) until two clicks are heard.

4. The AN/PVS-4A may be placed on theupper receiver rail in the most convenient slot forthe operator, as long as the rail grabber/mountdoes not extend beyond the rail.

5. If the AN/PVS-4A is removed the operator must take note of the position at which the device was zeroed, andeturn the device to that same position to insure zero is retained.

NOTE

Item (6) is depicted upside down in order to clearly show the bar which must fit into one of the slots on the rail.NOTE

The AN/PVS-4A may also be mounted on the M4 handle in the same manner as is used to mount on the handleof the M16A2. Items 5 & 6 will not be required when using this method. Insure that the mounting knob is insertedinto the hole in the carrying handle at an angle, due to the smaller gap between the top and bottom of the handle

(item 2 above).


25m Fired Zero Offsets: 0.0 Squares Left/Right; 4.4 Squares Down

10m Boresight Offsets: 0.0 cm Left/Right; .7.6 cm Up


Click for Bore

Sight Target


24/104

10m Boresight M4/M16A4 MWSAN/PVS-4A


AN/PVS-4Receiver Rail

0.0/7.6U

Laser Bore Light0/0


Bore Sighting the AN/PVS-4A1. Stabilize Weapon.2. Aim AN/PVS-4A at Cross Hair and adjust until the bore light strikes the Laser Borelight Dot.




M4/M16A4 MWSAN/PVS-14

3. Loosen the clamping knob on the weapon mount. Position the weapon mount with the monocular onto theweapons mounting rail. Tighten by turning the clamping knob.

NOTEThere is a ratchet in the weapon mount that prevents over tightening of the clamp. Turn until the knob clicks.

4. Check the position of the monocular by holding the weapon in your normal firing position. Adjust the fore/aftposition of the monocular as necessary by loosening the clamping knob and repositioning the weapon mount onthe weapons mounting rail.

NOTEThe MNVD can be used in conjunction with a collimated dot aiming device mounted on the

forward mounting rail. The brightness control for the aiming device should be set at or near its minimum setting.

Perform the following procedures for weapon mounted operation:

1. Ensure that the batteries are installed per the Tech Manual.

2. Assemble the weapon mount to the monocular as per steps 1 and 2, above.

3. Mount the monocular with adapter onto the M16/M4 receiver rail per steps 3 and 4, above.

4. Rotate the diopter adjustment for the clearest view of the image intensifier screen.

5. Adjust the objective lens focus (Figure 2-1) while observing an object until the sharpest image is obtained.

Target offsets required to properly zero the device to the weapon are as follows: NA. The AN/PVS-14 must beused in conjunction with either a laser aiming device or a collimated dot aiming device to be used as a weaponaiming system.


Perform the following procedure to install the weaponmount.

The MNVD is not a weapon sight, however, it can be used

in conjunction with a collimated dot sight or laser aimingdevice.

NOTEIt is recommended that the eyecup be replaced with the

eyeguard during weapon mounted use.

1. Orient the monocular and weapon mount as shown inFigure 2-16, Be sure to align the alignment boss on theweapon mount with the alignment groove in the monocular.

2. Screw in the thumbscrew to secure the monocular tothe weapon mount.


26/104

10m Boresight M4/M4A1/M16A4 with M4/M5 Adapter Rail System withAN/PVS-14 Mounted


Laser Bore Light0/0





M4/M16A4 MWSM68

CAUTIONHand tighten mounting hardware only. Using tools

to tighten mounting hardware could damageequipment.

NOTEThe sight assembly mounts directly to the upper receiverrail on top of the M4/M4A1 and M16A4. The mount is not

required. Make sure the spacer has been installedbefore mounting M68 on M4/M4A1 or M16A4.

1. If the same sight (serial number is on batterycompartment) is installed in the same position on the railon the same weapon, re-zeroing is not required.

2. Install sight assembly (1) on the upper receiver rail(2). Sight may be installed in any position on the upperreceiver rail. Make sure grabber edges area aroundmounting rail and torque bar is in slot. To ensure thatsight assembly is secure, tighten torque knob (3) until itclicks two times. Hand tighten only.


25m Fired Zero Offsets: 0.0 Squares Left/Right; 1.5 Squares Down10m Boresight Offsets: 0.0 cm Left/Right; 5.6 cm Up

See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets. See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.



28/104

10m Boresight M4/M4A1/M16A4 with M4/M5 Adapter Rail System withM68 Mounted


M68Receiver Rail

0.0/5.6U

Laser Bore Light0/0

Bore Sighting the M681. Stabilize Weapon.2. Aim CCO at the dot cross hair.3. Adjust the CCO until the laser bore light is centered on its dot.





M4/M16A4 MWSTA-31F (ACOG)


before proceeding.

CAUTIONHand tighten mounting hardware only. Using

tools to tighten mounting hardware coulddamage equipment.

NOTEThe ACOG sight mounts directly to the upper

receiver rail on top of the M4/M4A1 and M16A4using the integral mount/rail grabber.

1. Install sight assembly (1) on the upper receiver rail (2). Sight may be installed in any position on the upperreceiver rail. Make sure grabber edges area around mounting rail and torque bar is in slot. To ensure that sightassembly is secure, tighten knobs (3). Hand tighten only. Periodically check the knobs to insure that the sight isstill securely attached to the rail.

2. If the same sight (serial number is on battery compartment) is installed in the same position on the rail on thesame weapon, re-zeroing is not required.


10m Boresight Offsets: 0.0 cm Left/Right; 4.8 cm Up



1

2

3


30/104



M4/M16A4 MWSAN/PEQ-15 Using Integral Low Profile Rail Grabber

The AN/PEQ-15 (1) is mounted on the front left, top, orright rail (2) using its Integral Rail Grabber Bracket not

shown.

WARNING

Make sure the weapon is CLEAR and on SAFEbefore proceeding.

1. The rail grabber is an integral part of the AN/PEQ-15.


3. Position and tighten the Rail Grabber by turning the

knob clockwise.NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If however



25m Fired Zero Offsets:- Left Side Rail Mounting:

Visible: 2.5 cm Right; 3.5 cm UpIR: 3.5 cm Right; 4.5 cm Up

- Top Rail Mounting:Visible: 2.5 cm Left; 1.5 cm UpIR: 1.5 cm Left; .5 cm Up

- Right Side Rail Mounting:Visible: 3.0 cm Left; 7.0 cm UpIR: 4.0 cm Left; 6.0 cm Up

10m Boresight Offsets:- Left Side Rail Mounting:

Visible: 3.0 cm Left; 0.0 cm Up/DownIR: 4.0 cm Left; 1.0 cm Down

- Top Rail Mounting:Visible: 2.0 cm Right; 1.5 cm UpIR: 1.0 cm Right; 2.5 cm Up

- Right Side Rail Mounting:Visible: 3.0 cm Right; 4.5 cm DownIR: 4.0 cm Right; 3.5 cm Down



1

2

3


32/104


10m Boresight M4/M16A4 MWSAN/PEQ-15 Using Integral Low ProfileRail Grabber

Laser Bore Light0/0

AN/PEQ-15 VisibleTop Rail

2.5R/1.5U

AN/PEQ-15 IRTop Rail

1.0R/2.5U

ore Sighting the AN/PEQ-15. Stabilize Weapon.. Align Laser Borelight on its dot (See Annex F). Adjust Device until aiming laser is centered on the dot-cross hair.


AN/PEQ-15 IRRight Rail

4.0R/3.5D

AN/PEQ-15 VisibleRight Rail3.0R/4.5D

AN/PEQ-15 IRLeft Rail4.0L/1.0D

AN/PEQ-15Visible

Left Rail3.0L/0.0D




M4/M16A4 MWSAN/PAQ-4C Using Bracket/ Picatinny Rail Grabber &AN/PAS-13A/B(V)1/3 (Page 1 of 3 Pages)





10m Boresight Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.0 cm Left, 4.3 cm Down- Top: 1.8 cm Left, 3.9 cm Up- Right Side Rail Mounting: 6.0 cm Right, 0.9 cm Down


M4 MWS AN/PAQ-4C Mounting Instructions



before proceeding.




Click forNext Device



M4/M16A4 MWSAN/PAQ-4C Using Bracket/ Picatinny Rail Grabber &AN/PAS-13A/B(V)1/3 (Page 2 of 3 Pages)



1240-01-490-0737, Part No. A3281312-1) (3).

NOTEProcedures outlined below pertain to either M4 or M4A1

variants.

NOTE


5340-01-502-7971) to the TWS.




3. Select a slot on rail. Any slot may be used as long as rail grabber/mount does not hang over edge of rail. If theTWS is removed from the rail the operator must note the position at which the device was zeroed, and return thedevice to that position in order to retain zero.




10m Boresight Offsets:- AN/PAS-13B(v)1 (LWTS): 0.0 cm Left/Right; 7.9 cm Up

- AN/PAS-13A/B(V)3 (HWTS): 0.0 cm Left/Right; 9.4 cm Up





35/104


10m Boresight M4/M16A4 MWSAN/PAQ-4C Using Bracket/ PicatinnyRail Grabber & AN/PAS-13A/B(V)1/3 (Page 3 of 3 Pages)

AN/PAQ-4B/C

Left Rail6.0L/4.3D



Laser Bore Light

0/0


Bore Sighting the AN/PAQ-41. Stabilize Weapon.2. Align Laser Borelight on its dot (See Annex F)3. Adjust Device until aiming laser is centered on the dot-cross hair.Bore Sighting the AN/PAS-13A/B (V)1/31. Stabilize Weapon.2. Place Thermal signature material or tips of fingers on gray circles.3. Aim between gray circles at cross-hair.

4. Adjust AN/PAS-13A/B(V)1/3 until the bore light laser is centered on its dot.5. You MUST zero reticle in both wide and narrow field of view.

AN/PAS-13A/B (V)3Receiver Rail

0.0/9.4UHeat Source/ Fingers

AN/PAS-13B (V)1Receiver Rail

0.0/7.9U

Heat Source/ Fingers




M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber & AN/PVS-4A (Page 1 of 3 Pages)



Target offsets required to properly zero the device to the weapon are as follows:25m Fired Zero Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.5 Squares Right, 8.0 Squares Up- Top Rail: 1.7 Squares Right, 0.7 Squares Down- Right Side Rail Mounting: 5.9 Squares Left, 3.5 Squares Up




The AN/PAQ-4C may be mounted on the left, top orright side rails using the Mounting Bracket/Picatinny Rail Grabber (NSN 5340-01-458-0473)

depicted in the diagram at left.


before proceeding.


2. Loosen the clamping knob until the railgrabber/mount has sufficient space to fit over the left

side rail (3). Tighten the clamping knob until two clicksare heard.


Click for

Next Device



M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber & AN/PVS-4A (Page 2 of 3 Pages)








NOTEItem (6) is depicted upside down in order to clearly show the bar which must fit into one of the slots on the rail.

NOTEThe AN/PVS-4A may also be mounted on the M4 handle in the same manner as is used to mount on the handle

of the M16A2. Items 5 & 6 will not be required when using this method. Insure that the mounting knob is insertedinto the hole in the carrying handle at an angle, due to the smaller gap between the top and bottom of the handle

(item 2 above).








38/104


10m Boresight M4/M16A4 MWSAN/PAQ-4C Using MountingBracket/Picatinny Rail Grabber & AN/PVS-4A (Page 2 of 3 Pages)


6.0L/4.3D



Laser Bore Light0/0




0.0/7.6U





M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber w/ AN/PVS-14 & M68 (Page 1 of 4 Pages)







The AN/PAQ-4C may be mounted on the left or rightside rails using the Mounting Bracket/ PicatinnyRail Grabber (NSN 5340-01-458-0473) depicted inthe diagram at left. Top rail is not available sincethe M68 will be mounted there in a following step.


before proceeding.









The MNVD is not a weapon sight, however, it can beused in conjunction with a collimated dot sight or laser

aiming device.



1. Orient the monocular and weapon mount as shownin the figure to the left, Be sure to align the alignmentboss on the weapon mount with the alignment groovein the monocular.

2. Screw in the thumbscrew to secure the monocularto the weapon mount.



4. Check the position of the monocular by holding the weapon in your normal firing position. Adjust the fore/aftposition of the monocular as necessary by loosening the clamping knob and repositioning the weapon mount on

the weapons mounting rail.




1. Ensure that the batteries are installed per the Tech Manual.2. Assemble the weapon mount to the monocular as per steps 1 and 2, above.3. Mount the monocular with adapter onto the M16/M4 receiver rail per steps 3 and 4, above.4. Rotate the diopter adjustment for the clearest view of the image intensifier screen.5. Adjust the objective lens focus while observing an object until the sharpest image is obtained.








NOTEThe AN/PVS-14 was previously mounted to the upper

receiver rail on top of the M4/M4A1 or M16A4.

1. The M68 is mounted on the hand guard top rail,immediately in front of the AN/PVS-14. For older modelM68s make sure the spacer has been installed beforemounting M68 on M4/M4A1 or M16A4.

NOTEIf the same sight (serial number is on battery

compartment) is installed in the same position on the railon the same weapon, re-zeroing is not required.

2. Install sight assembly (1) on the hand guard top rail (2). Sight may be installed in any position on the rail.Make sure grabber edges area around mounting rail and torque bar is in slot. To ensure that sight assembly issecure, tighten torque knob (3) until it clicks two times. Hand tighten only.





1

2

3

M68


42/104



M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber & M68 (Page 1 of 3 Pages)










before proceeding.






44/104


45/104



M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber & TA-31F (ACOG) (Page 1 of 3 Pages)

2. Loosen the clamping knob (3) until the rail grabber/mount has sufficient space to fit over the left side rail (4).Tighten the clamping knob until two clicks are heard.

3. Install the remote switch in a convenient location using the provided cable hangers.










before proceeding.



1

2

3

4



M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber & TA-31F (ACOG) (Page 2 of 3 Pages)


before proceeding.











1

2

3


48/104

10m Boresight M4/M16A4 MWSAN/PAQ-4C Using MountingBracket/Picatinny Rail Grabber & TA-31F (ACOG) (Page 3 of 3 Pages)



Laser Bore Light0/0

ACOGReceiver Rail

0.0/4.8U

Bore Sighting the TA31F (ACOG)1. Stabilize Weapon.2. Align Laser Borelight on its dot3. Adjust ACOG until bottom of the chevron (300M) is centered on the dot-cross hair.




6.0L/4.3D





M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber &the AN/PAS-13A/B(V)1/3 (Page 1 of 3 Pages)

The Aiming Light is mounted on the front left-hand,top, or right-hand rail using the Insight rail grabberbracket (NSN 5340-01-458-0990) when it is desired tokeep the Aiming Light as close as possible to thebarrel.


before proceeding.



3. Turn the ON/OFF Switch CCW to the #1OFF/STORAGE position.





Target offsets required to properly zero the device to the weapon are as follows




- Left Side Rail Mounting: 4.3 cm Left; 4.2cm Down

- Top Rail Mounting: 1.8 cm Left; 2.2 cm Up- Right Side Rail Mounting: 4.3 cm Right; .7 cm Down






M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber &the AN/PAS-13A/B(V)1/3 (Page 2 of 3)



1240-01-490-0737, Part No. A3281312-1) (3).


variants.

NOTE


5340-01-502-7971) to the TWS.








10m Boresight Offsets:- AN/PAS-13B(v)1 (LWTS): 0.0 cm Left/Right; 7.9 cm Up- AN/PAS-13A/B(V)3 (HWTS): 0.0 cm Left/Right; 9.4 cm Up





51/104


10m Boresight M4/M16A4 MWSAN/PAQ-4C Using Insight Low ProfileRail Grabber & the AN/PAS-13A/B(V)1/3 (Page 3 of 3 Pages)

AN/PAQ-4B/C

Left Rail4.3L/4.2D



Laser Bore Light

0/0



ore Sighting the AN/PAS-13A/B (V)1/3Stabilize Weapon.Place Thermal signature material or tips of fingers on gray circles.Aim between gray circles at cross-hair.

Adjust AN/PAS-13A/B(V)1/3 until the bore light laser is centered on its dot.You MUST zero reticle in both wide and narrow field of view.




0.0/7.9U




52/104


53/104


54/104


10m Boresight M4/M16A4 MWSAN/PAQ-4C Using Insight Low ProfileRail Grabber & the AN/PVS-4A (Page 3 of 3 Pages)




Laser Bore Light0/0




0.0/7.6U

ore Sighting the AN/PVS-4A. Stabilize Weapon. Aim AN/PVS-4A at Cross Hair and adjust until the bore light strikes the Laser Borelight Dot.



55/104


56/104



M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber,AN/PVS-14, & M68 (Page 3 of 4 Pages)

Click for Bore

Sight Target





1. The M68 is mounted on the hand guard top rail,immediately in front of the AN/PVS-14. Make sure thespacer has been installed before mounting M68 onM4/M4A1 or M16A4.









58/104


10m Boresight M4/M16A4 MWSAN/PAQ-4C Using Insight Low ProfileRail Grabber, AN/PVS-14, & M68 (Page 4 of 4 Pages)




Laser Bore Light0/0



M68

Receiver Rail0.0/5.6U

ore Sighting the M68. Stabilize Weapon.. Aim CCO at the dot cross hair. Adjust the CCO until the laser bore light is centered on its dot.




M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber &M68 (Page 1 of 3 Pages)

The Aiming Light is mounted on the front left-hand, topor right-hand rail using the Insight rail grabber bracket(NSN 5340-01-458-0990) when it is desired to keepthe Aiming Light as close as possible to the barrel.

WARNINGMake sure the weapon is CLEAR and on SAFEbefore proceeding.



3. Turn the ON/OFF Switch CCW to the #1

OFF/STORAGE position.





Target offsets required to properly zero the device to the weapon are as follows25m Fired Zero Offsets:



- Left Side Rail Mounting: 4.3 cm Left; 4.2cm Down- Top Rail Mounting: 1.8 cm Left; 2.2 cm Up

- Right Side Rail Mounting: 4.3 cm Right; .7 cm Down See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.





M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber &M68 (Page 2 of 3 Pages)












61/104


10m Boresight M4/M16A4 MWSAN/PAQ-4C Using Insight Low ProfileRail Grabber & M68 (Page 1 of 3 Pages)




Laser Bore Light0/0



M68

Receiver Rail0.0/5.6U

ore Sighting the M68. Stabilize Weapon.. Aim CCO at the dot cross hair. Adjust the CCO until the laser bore light is centered on its dot.




M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber &TA31F (ACOG) (Page 1 of 3 Pages)

The Aiming Light is mounted on the front left-hand, topor right-hand rail using the Insight rail grabber bracket(NSN 5340-01-458-0990) when it is desired to keepthe Aiming Light as close as possible to the barrel.


before proceeding.



3. Turn the ON/OFF Switch CCW to the #1

OFF/STORAGE position.





Target offsets required to properly zero the device to the weapon are as follows25m Fired Zero Offsets:



- Left Side Rail Mounting: 4.3 cm Left; 4.2cm Down- Top Rail Mounting: 1.8 cm Left; 2.2 cm Up

- Right Side Rail Mounting: 4.3 cm Right; .7 cm Down See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.





M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber &TA31F (ACOG) (Page 2 of 3 Pages)


before proceeding.











1

2

3


64/104


10m Boresight M4/M16A4 MWSAN/PAQ-4C Using Insight Low ProfileRail Grabber & TA31F (ACOG) (Page 3 of 3 Pages)




Laser Bore Light0/0



ACOGReceiver Rail

0.0/4.8U

ore Sighting the TA31F (ACOG). Stabilize Weapon.. Align Laser Borelight on its dot Adjust ACOG until bottom of the chevron (300M) is centered on the dot-cross hair.




M4/M16A4 MWSAN/PAS-13A/B(V)1/3 L/HWTS and AN/PEQ-2A Mounted(Page 1 of 3)



1240-01-490-0737, Part No. A3281312-1) (3).


variants.

NOTE


5340-01-502-7971) to the TWS.








10m Boresight Offsets:- AN/PAS-13B(v)1 (LWTS): 0.0 cm Left/Right; 7.9 cm Up- AN/PAS-13A/B(V)3 (HWTS): 0.0 cm Left/Right; 9.4 cm Up






M4/M16A4 MWSAN/PAS-13A/B(V)1/3 L/HWTS and AN/PEQ-2A Mounted(Page 2 of 3 Pages)

The AN/PEQ-2A (1) is mounted on the front left side,top, or right side rail (2) using the Insight Rail Grabber

Bracket (NSN 5340-01-458-0990) (3).


before proceeding.











- Top Rail Mounting:Aiming: 2.0 cm Right; 2.3 cm Up

Flood: 2.0 cm Left; 2.3 cm Up- Right Side Rail Mounting:Aiming: 4.5 cm Right; 4.4 cm DownFlood: 4.5 cm Right; 0.4 cm Down




67/104

10m Boresight M4/M16A4 MWSAN/PAS-13A/B(V)1/3 L/HWTS andAN/PEQ-2A Mounted (Page 3 of 3 Pages)




Bore Sighting the AN/PAS-13A/B (V)1/31. Stabilize Weapon.2. Place Thermal signature material or tips of fingers on gray circles.3. Aim between gray circles at cross-hair.4. Adjust AN/PAS-13A/B(V)1/3 until the bore light laser is centered on its dot.5. You MUST zero reticle in both wide and narrow field of view.


0.0/7.9U




AN/PEQ-2A Aim

Right Rail4.5R, 4.4D


AN/PEQ-2A FloodLeft Rail4.5L/5.0D


AN/PEQ-2A AimTop Rail2.0R/2.3U

Bore Sighting the AN/PEQ-21. Stabilize Weapon.

2. Align Laser Borelight on its dot (See Annex F)3. Adjust Device until aiming laser is centered on the dot-cross hair.4. Adjust AN/PEQ-2A Flood Light until the laser is centered on the

designated dot.




M4/M16A4 MWSwith AN/PEQ-2A AN/PVS-4A MTD(Page 1 of 3 Pages)


Bracket (NSN 5340-01-458-0990) (3).


before proceeding.












Flood: 2.0 cm Left; 2.3 cm Up- Right Side Rail Mounting:Aiming: 4.5 cm Right; 4.4 cm DownFlood: 4.5 cm Right; 0.4 cm Down


Click fornext Device



M4/M16A4 MWSwith AN/PEQ-2A AN/PVS-4A MTD(Page 2 of 3 Pages)








NOTEItem (6) is depicted upside down in order to clearly show the bar which must fit into one of the slots on the rail.

NOTEThe AN/PVS-4A may also be mounted on the M4 handle in the same manner as is used to mount on the handle

of the M16A2. Items 5 & 6 will not be required when using this method. Insure that the mounting knob is insertedinto the hole in the carrying handle at an angle, due to the smaller gap between the top and bottom of the handle

(item 2 above).








70/104

10m Boresight M4/M16A4 MWSwith AN/PEQ-2A AN/PVS-4A MTD(Page 3 of 3 Pages)





0.0/7.6U

Laser Bore Light0/0

AN/PEQ-2A AimRight Rail4.5R, 4.4D


AN/PEQ-2A Flood

Left Rail4.5L/5.0D



2.0R/2.3U


Bore Sighting the AN/PEQ-21. Stabilize Weapon.2. Align Laser Borelight on its dot (See Annex F)3. Adjust Device until aiming laser is centered on the dot-cross hair.4. Adjust AN/PEQ-2A Flood Light until the laser is centered on the designated dot.




M4/M16A4 MWSAN/PEQ-2A Using Insight Low Profile Rail Grabber,AN/PVS-14, & M68 (Page 1 of 4 Pages)

The AN/PEQ-2A (1) is mounted on the front left side orright side rail (2) using the Insight Rail Grabber Bracket

(NSN 5340-01-458-0990) (3). The top rail is notavailable since the M68 will be mounted there in a

following step.


before proceeding.


2. Loosen the clamping knob (5) on the rail grabberuntil the rail grabber has sufficient space to fit over the

left side rail.3. Position and tighten the Rail Grabber by turning theknob clockwise.

NOTEThe device may be placed on the left or right rail, wherever is most convenient for the operator. If however thedevice is removed from the rail the operator must take note of the position at which the device was zeroed, and

return the device to that same position in order to insure that zero is retained.






- Top Rail Mounting:Aiming: 2.0 cm Right; 2.3 cm UpFlood: 2.0 cm Left; 2.3 cm Up

- Right Side Rail Mounting:Aiming: 4.5 cm Right; 4.4 cm DownFlood: 4.5 cm Right; 0.4 cm Down


Click for NextDevice






4. Check the position of the monocular by holding the weapon in your normal firing position. Adjust the fore/aftposition of the monocular as necessary by loosening the clamping knob and repositioning the weapon mount onthe weapons mounting rail.




1. Ensure that the batteries are installed per the Tech Manual.

2. Assemble the weapon mount to the monocular as per steps 1 and 2, above.

3. Mount the monocular with adapter onto the M16/M4 receiver rail per steps 3 and 4, above.

4. Rotate the diopter adjustment for the clearest view of the image intensifier screen.

5. Adjust the objective lens focus (Figure 2-1) while observing an object until the sharpest image is obtained.




The MNVD is not a weapon sight, however, it can be

used in conjunction with a collimated dot sight or laseraiming device.



1. Orient the monocular and weapon mount as shownin Figure 2-16, Be sure to align the alignment boss onthe weapon mount with the alignment groove in themonocular.

2. Screw in the thumbscrew to secure the monocular tothe weapon mount.





1

2

3





1. The M68 is mounted on the hand guard top rail,immediately in front of the AN/PVS-14. Make sure thespacer has been installed before mounting M68 onM4/M4A1 or M16A4.








74/104



10m Boresight M4/M16A4 MWSAN/PEQ-2A Using Insight Low ProfileRail Grabber, AN/PVS-14, & M68 (Page 4 of 4 Pages)

Laser Bore Light0/0



AN/PEQ-2A Flood

Left Rail4.5L/5.0D



2.0R/2.3U



M68Receiver Rail

0.0/5.6U

ore Sighting the M68. Stabilize Weapon.. Aim CCO at the dot cross hair.

Adjust the CCO until the laser bore light is centered on its dot.




M4/M16A4 MWSAN/PEQ-2A Using Insight Low Profile Rail Grabber &M68 (Page 1 of 3 Pages)


Bracket (NSN 5340-01-458-0990) (3).


before proceeding.












Flood: 2.0 cm Left; 2.3 cm Up- Right Side Rail Mounting:

Aiming: 4.5 cm Right; 4.4 cm DownFlood: 4.5 cm Right; 0.4 cm Down





M4/M16A4 MWSAN/PEQ-2A Using Insight Low Profile Rail Grabber &M68 (Page 2 of 3 Pages)












77/104



10m Boresight M4/M16A4 MWSAN/PEQ-2A Using Insight Low ProfileRail Grabber & M68 (Page 3 of 3 Pages)

Laser Bore Light0/0



AN/PEQ-2A Flood

Left Rail4.5L/5.0D



2.0R/2.3U



M68Receiver Rail

0.0/5.6U

ore Sighting the M68. Stabilize Weapon.. Aim CCO at the dot cross hair.

Adjust the CCO until the laser bore light is centered on its dot.




M4/M16A4 MWSAN/PEQ-2A Using Insight Low Profile Rail Grabber &TA 31F (ACOG) (Page 1 of 3 Pages)

The AN/PEQ-2A (1) is mounted on the front left side(2), top, or right side rail using the Insight Rail Grabber

Bracket (NSN 5340-01-458-0990) (3).

WARNINGMake sure the weapon is CLEAR and on SAFEbefore proceeding.



3. Position and tighten the Rail Grabber by turning theknob cl

saib rifles & carbines with ars

Documents