PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUNDCURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing LLC. may repair or replacethe product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacementof products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.

For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com

MAKE: STYLE:

MIN.30

WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY

WEIGHT CARRYING:

INSTALLATION TIPS: INSTALLATION TIME:

INSTALLATION REQUIRES:

VEHICLE PHOTO:

HITCH ILLUSTRATION:

REPRESENTATIVE PHOTO

MAKE SURE YOUR HITCH MATCHES

LEVEL OF DIFFICULTY: MODERATE

EASY MODERATE CHALLENGING

THE INSTALL TIME LISTED IS FOR PROFESSIONAL

INSTALLERS. IF YOU ARE HESITANT TO UNDERTAKE

THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED

CURT INSTALLER FOR ADDITIONAL ASSISTANCE.

1. BEFORE YOU BEGIN INSTALLATION, READ ALL

INSTRUCTIONS THOROUGHLY.

2. TO EASE INSTALLATION, 2 PEOPLE MAY BE

REQUIRED.

3. USING PROPER TOOLS WILL GREATLY IMPROVE

THE QUALITY OF THE INSTALL AND REDUCE THE

TIME REQUIRED.

4. NEED HELP OR HAVE SOME QUESTIONS?

CALL TECHNICAL SUPPORT AT 800.798.0813

Safety glasses should be worn at all times whileinstalling this product.

YEARS: 2012-PRESENT LAND ROVER MODEL: RANGE ROVER EVOQUE CROSSOVER

4,000

600

TRAILER WEIGHT:

TONGUE WEIGHT:

13128 INSTALLATION INSTRUCTIONS

LBS.

LBS.

1-30-13

WARNING: WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER (WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT WWW.CURTMFG.COM FOR FURTHER INFORMATION.

AVIATION

SHEARS

CUT-OFFWHEEL

MASKINGTAPE PRY BAR RATCHET

SAFETYGLASSES SOCKET

10mm15mm22mm3/4" TORXBIT

SOCKETT-30

TAPEMEASURE

TORQUEWRENCH

PART REMOVAL

REVERSE FISHWIRE FASTENERS

TEMPORARILY LOWER EXHAUST

NO DRILLING REQUIRED

FASCIA TRIMMING REQUIRED

HEAT SHIELD REMOVAL OR TRIMMING REQUIRED

INSTALLATION WALKTHROUGH:

For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com

Parts List

DESCRIPTIONPART NUMBERQTYITEM

HEX BOLTM14 - 2 x 110 HEX11

CONICAL TOOTHED WASHER9/16" CONICAL WASHER12

CARRIAGE BOLT1/2-13 x 1 3/413

.250" SQUARE HOLE SPACERCM-SP614

CONICAL TOOTHED WASHER1/215

HEX NUT1/2-1316

HEX FLANGE BOLTM12 - 1.75 x 3537

1/2" FISHWIRE1_2 FISHWIRE18

8

77 7

3

4

2

1

5

6

PASSENGER SIDEFRAME RAIL

DRIVER SIDEFRAME RAIL

WELDNUT PLATE WITH TUBE SPACERS IN DRIVER SIDE FRAME

TOW HOOK BRACKET ONPASSENGER SIDE FRAMERAIL

EXISTING WELDNUTSIN TOW HOOK BRACKET

1. Lower exhaust by removing bolt which attaches exhaust hanger bracket on passenger side frame rail, then disconnecting 2 rubber isolators. Support exhaust to prevent it from being damaged.

2. Remove rear heat shield at vehicle fascia by removing 4 hex bolts and 8 Torx bolts. Heat shield may either be trimmed and reinstalled or permanently removed.

INSTALLATION WALKTHROUGH:

For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com

3. Reverse fishwire 1/2" carriage bolt and spacer up through slot in driver side frame rail and back down through slot.

4. Trim fascia as shown, approximately 3 3/4" long x 1" wide (See Fascia Trim Diagram).

5. Raise hitch into position, being careful not to push 1/2" carriage bolt back into frame. 6. Install remaining fasteners as shown. Torque all 1/2" fasteners to 110 ft-lbs, torque all M12 fasteners to 79 ft-lbs, torque all M14 fasteners to 126 ft-lbs.

7. Raise exhaust back into position. Installation is complete

3 3/4"

1"

CENTER OFVEHICLE

FASCIA TRIM DIAGRAM

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.

***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***

WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.

** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**

HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813

HITCH WEIGHT: LBS.

INSTALL TIME

PROFESSIONAL: MINUTES

NOVICE (DIY): MINUTES

INSTALL NOTES:

INSTALLATION STEPS

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS

ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.

Curt Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,Curt Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation ofthis product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental orconsequential loss or damage.

4,000 600

30

30

LAND ROVER RANGE ROVER EVOQUE

1-30-13

13128

65

Parts List

DESCRIPTIONPART NUMBERQTYITEM

HEX BOLTM14 - 2 x 110 HEX11

CONICAL TOOTHED WASHER9/16" CONICAL WASHER12

CARRIAGE BOLT1/2-13 x 1 3/413

.250" SQUARE HOLE SPACERCM-SP614

CONICAL TOOTHED WASHER1/215

HEX NUT1/2-1316

HEX FLANGE BOLTM12 - 1.75 x 3537

1/2" FISHWIRE1_2 FISHWIRE18

PASSENGER SIDE FRAME RAIL

DRIVER SIDE FRAME RAIL

TOOLS REQUIREDTORQUE WRENCH

RATCHETPRY BAR

TAPE MEASURECUT OFF WHEEL

TIN SNIPS10mm, 15mm, 22mm SOCKETS

3/4" SOCKETT-30 TORX BIT

-NO DRILLING REQUIRED-REVERSE FISHWIRE HARDWARE-LOWER EXHAUST-REMOVE OR TRIM HEAT SHIELD-FASCIA TRIMMING REQUIRED

8

3

4

2

1

6

5

77

7

WELDNUT PLATE WITHTUBE SPACERS INDRIVER SIDE FRAME

TOW HOOK BRACKETON PASSENGER SIDEFRAME RAIL

EXISTING WELDNUTS IN TOW HOOK BRACKET

1. Lower exhaust by removing bolt which attaches exhaust hanger bracket on passenger side frame rail, then disconnecting 2 rubber isolators. Support exhaust to prevent it from being damaged.

2. Remove rear heat shield at vehicle fascia by removing 4 hex bolts and 8 Torx bolts. Heat shield may either be trimmed and reinstalled or permanently removed.

3. Reverse fishwire 1/2" carriage bolt and spacer up through slot in driver side frame rail and back down through slot.

4. Trim fascia as shown, approximately 3 3/4" long X 1" wide (See Fascia Trim Diagram).

5. Raise hitch into position, being careful not to push 1/2" carriage bolt back into frame.

6. Install remaining fasteners as shown. Torque all 1/2" fasteners to 110 ft-lbs, torque all M12 fasteners to 79 ft-lbs, torque all M14 fasteners to 126 ft-lbs.

7. Raise exhaust back into position.

1 7/8"

3 3/4"

1"

CENTER OFVEHICLE

FASCIA TRIM DIAGRAM