saddle clamp pvc
TRANSCRIPT
Simple Two-Piece DesignEngineered for Reliability
Viton® is a registered trademark of DuPont Dow Elastomers.
Visit our web site: www.spearsmfg.comPROGRESSIVE PRODUCTS FROM SPEARS INNOVATION & TECHNOLOGY
Sample Engineering SpecificationAll plastic saddle fittings shall be clamp-on type with O-ring seal constructed from PVC Type I cell classification 12454 or CPVC Type IV cell classification 23447. All O-rings shall be Buna-N, EPDM or Viton®. All saddles shall be piloted at O-ring area for positive positioning in pipe. All bolt clamping hardware shall be zinc plated steel or stainless steel. All threaded saddle outlets shall be Steel Reinforced (SR) design. Saddles shall be pressure rated at 235 psi for use on pipe sizes through 4" nominal IPS diameters and 200 psi for use on 6" pipe, maximum internal pressure for water at 73°F, as manufactured by Spears Manufacturing Company.
Excellent Metal-to-Plastic System TransitionEasily installs on metal pipe as a transition to plastic system.
PVC & CPVC Tee or CrossConfigurationsAvailable in PVC Schedule 40 and PVC or CPVC Schedule 80 in 2" - 6" pipe saddle with choice of slip or Steel Reinforced (SR) thread outlet sizes ranging from 1/2" through 4" with single Tee or double Cross outlets.
Patented SR Design Female ThreadsPatented Stainless Steel Reinforced (SR) design on female thread outlets for superior strength.
O-ring OptionsChoice of high grade Buna-N or EPDM O-rings for Schedule 40 and EPDM or Viton® O-rings for Schedule 80, for application specific selection for optimum chemical resistance.
4-Bolt Design, Choice of HardwarePositive attachment eliminates splitting problems associated with plastic wedge fasteners and outperforms 2-Bolt clamp saddle designs. Choose zinc plated or stainless steel nut, bolt and washer hardware.
Excellent Pressure Capabilities Maximum internal pressure rating of 235 psi through 4" and 200 psi for 6" at 73°F.
Special pilot engageswith hole in pipe toprevent saddledislocation.
O-ring seal providespositive, trouble-freesealing to pipe.
Spears PVC & CPVC Clamp-On Saddles allow quick, easy and reliable addition of branch lines to existing piping system lines. These versatile saddle units can be used in either temporary or permanent installations on all types of pipe with IPS (Iron Pipe size) outside diameter, such as PVC, CPVC, Polyethylene, Polypropylene and Steel.
COS-2-0500
PVC & CPVC CLAMP-ON SADDLESSPEARS
Simple Installation
Copyright 2000 Spears Manufacturing Company. All Rights Reserved. Printed in the United States of America 9/00. COS-2-0500©
1.Using a standard industrial grade hole-saw, cut specified hole in desired position on pipe according to recommended hole saw size engraved on the saddle. Note: Care must be taken to deburr hole and remove all residue from hole area to assure tight fit and avoid leakage.
2.Fully seat O-ring in groove on underside of saddle outlet component. Position over hole and fully seat saddle onto pipe. Note: Saddle outlets are piloted. Be sure pilot lip fully engages with hole in pipe.
3.Place strap component opposite outlet and secure with bolts (4), nuts (4) and washers (8). Important: Washers MUST be placed under each bolt head (1) and under each nut (1) to avoid damage to saddle.
4.Tighten bolts to specified torque:
1Outlet-sized with bushing
2 x 1/2 3/4 82 x 3/4 7/8 82 x 1 1-1/8 8
2 x 1-1/4 1-1/2 82 x 1-1/2 1-1/2 8
2-1/2 x 1-1/2 1-3/4 83 x 1/21 7/8 83 x 3/4 7/8 83 x 1 1-1/8 8
3 x 1-1/41 2-1/4 83 x 1-1/21 2-1/4 8
3 x 2 2-1/4 84 x 1/21 1-1/8 84 x 3/41 1-1/8 8
4 x 1 1-1/8 84 x 1-1/41 1-3/4 84 x 1-1/2 1-3/4 8
4 x 2 2-1/4 84 x 2-1/21 3 8
4 x 3 3 86 x 1/21 1-1/8 106 x 3/41 1-1/8 10
6 x 1 1-1/8 106 x 1-1/41 2-1/4 106 x 1-1/21 2-1/4 10
6 x 2 2-1/4 106 x 2-1/21 3 10
6 x 3 3 106 x 4 4 10
Saddle x OutletSize
RecommendedHole Size
Recommended Bolt Torque
ft/lbs
SPEARS® MANUFACTURING COMPANY
MIDWESTFLORIDANORTHEAST15853 Olden Street
Sylmar (Los Angeles), CA 91342P.O. Box 9203
Sylmar, CA 91392(818) 364-1611
FAX: (818) 898-3774E-mail: [email protected]
INTERNATIONAL SALES854 Fairway Drive
Bensenville (Chicago), IL60106
(630) 773-0075(800) 662-6330
FAX: (630) 773-0435
3445 Barlett BoulevardOrlando, FL
32811(407) 843-1960(800) 327-6390
FAX: (407) 425-3563
SOUTHEAST2751 Miller Road
Decatur (Atlanta), GA30035
(770) 981-7122(800) 662-6326
FAX: (770) 981-6106
543 Industrial DriveLewisberry (Harrisburg), PA
17339-9532(717) 938-8844(800) 233-0275
FAX: (717) 938-6547
15860 Olden StreetSylmar (Los Angeles), CA 91342P.O. Box 9203, Sylmar, CA 91392
(818) 364-1611(800) 862-1499
FAX: (818) 367-3014
PACIFIC SOUTHWEST NORTHWEST3902 "B" Street N.W.Auburn (Seattle), WA
98001(253) 939-4433(800) 347-7327
FAX: (253) 939-7557
1415 South 700 West #3Salt Lake City, UT
84104(801) 972-0659
FAX: (801) 972-0688
UTAH1838 Forms Drive
Carrollton (Dallas), TX75006
(972) 245-0387(800) 441-1437
FAX: (972) 245-4205
SOUTH CENTRAL4880 Florence Street
Denver, CO80238
(303) 371-9430(800) 777-4154
FAX: (303) 375-9546
ROCKY MOUNTAIN
CORPORATE OFFICES15853 Olden Street, Sylmar, CA 91342
P.O. Box 9203, Sylmar, CA 91392(818) 364-1611 • http://www.spearsmfg.com
SPEARS