s3035 gm genius ultra +t 180a en - graupner · s3035 gm genius ultra +t 180a Ð switch cable,...

ManualGM Genius Ultra +T 180A Telemetry speed controllerNo. S3035No. S3035.1

2S3035

Content table

Introduction ....................................................................3

Service centre .................................................................3

Intended use .................................................................4

Package content ............................................................4

Symbols explication .......................................................4

Safety notes ...................................................................5

Controller connections ...................................................7

Installation in the model and use .....................................8

Throttle stick setting .......................................................9

Programming without HoTT transmitter ........................10

Programming with the program box .............................10

Settable values in program ...........................................11

Special features ............................................................12

LED error messages .....................................................13

LED Status display .......................................................13

ESC Data View in telemetry menu ................................13

Programming with HoTT transmitter .............................14

Warning messages .......................................................19

Programming warning thresholds .................................20

Saving of the warnings and thresholds .........................20

Graphic display of telemetry data ..................................21

Technical data ..............................................................22

Firmware Update ..........................................................23

Declaration of conformity ..............................................25

Notes for environmental protection ...............................28

Care and maintenance .................................................28

Warranty .......................................................................28

INNOVATION & TECHNOLOGIE

3S3035

Graupner in Internet

Introduction

Thank you for choosing a GM GENIUS ULTRA +T 180A TELEME-TRY SPEED CONTROLLER. This controller is extremely versatile.Read this manual carefully to achieve the best results with your speed controller and to safely control all your models. If you experience any trouble during operation, take the instruc-tions to help or ask your dealer or Graupner Service Centre.Due to technical changes, the information may be changed in this manual without prior notice.This product complies with national and European legal re-quirements.

To maintain this condition and to ensure safe operation, you must read and follow this user manual and the safety notes before using the product!

NoteThis manual is part of that product. It contains important in-formation concerning operation and handling. Keep these instructions for future reference! Take this into consideration when you pass it on to other future owner.

Service centre

Graupner/SJ-ZentralserviceGraupner/SJ GmbHHenriettenstrasse 96D-73230 Kirchheim / Teck

Servicehotline (+49) (0)7021/722-130Mon - Thu7:30 am - 9:00 am9:15 am - 4:00 pmFriday9:00 am - 1:00 pm

For the sevice centres outside Germany please refer to our web site www.graupner.de

4S3035

Intended use

The GM GENIUS ULTRA +T 180A TELEMETRY SPEED CONTROLLER regulates the speed of brushless motors used in model cars. The GM GENIUS ULTRA +T 180A TELEMETRY SPEED CONTROLLER is specifically designed to be used in RC battery powered cars, no other use is allowed. For any improper use no warranty or liability is allowed.Read through this entire manual before you attempt to install or use the GM GENIUS ULTRA +T 180A TELEMETRY SPEED CONT-ROLLER.Graupner/SJ constantly works on the development of all prod-ucts; we reserve the right to change the item, its technology and equipment.

Target groupThe product is not a toy. It is not suitable for children under 14 years. The installation and operation of the controller must be performed by experienced modellers. If you do not have sufficient knowledge about dealing with radio-con-trolled models, please contact an experienced modeller or a model club.

Package content

S3035 GM GENIUS ULTRA +T 180A Ð Switch cable, telemetry cable, sensor cable Ð Shrink tube, Futaba plug Ð User manual

S3035.1GM GENIUS ULTRA +T 180A Ð Switch cable, telemetry cable, sensor cable Ð Shrink tube, Futaba plug Ð User manual Ð S8272 Programmer Box

Symbols explication

Always follow the information marked with the CAUTION or WARNING symbol. The signal word WARNING indicates the potential for serious injury, the signal word CAUTION indi-cates potential minor injuries.NOTES, ATTENTION inform you about possible things damages.


5S3035

Safety notes

General Ð These safety instructions are intended not only to protect

the product, but also for your own and other people’s safe-ty. Therefore please read this section very carefully before using the product!

Ð Do not leave the packaging material lying around, this could be a dangerous toy for children.

Ð Persons, including children, with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, or not capable to use safely the speed controller, must not use it without supervision or instruction by a responsible person.

Ð The operation of radio controlled models must be learned! If you have never driven such a model, then start extra carefully and make sure to be familiar with the reactions of the model to the remote control commands. Proceed responsibly.

Ð Always carry on a first range test and function test on the ground (hold the model tightly) before your model is used. Repeat the test with the motor running and with short bursts of throttle.

Ð Before you select the remote control mode, you have to check the further relevant laws and regulations. These laws you must obey in every case. Pay attention to the possibly different laws of the countries.

Ð The insurance is mandatory for all kinds of model opera-tion. If you already have one check out whether the op-eration of the model is covered. If applicable, extend it to special model liability insurance.

Ð For safety and (CE) certification the unauthorized conver-sion and / or modification of the product is not permitted.

Ð They may only be used our recommended components and accessories. Use only genuine matching Graupner connectors of the same design and the same material.

Ð Make sure that all connections are secure. Do not pull on the cables when you unplug the connector.

Ð Protect all equipment from dust, dirt, moisture and other foreign parts. Do not expose this equipment to vibration and excessive heat or cold. The remote control operation may be carried out only in “normal” ambient temperatures, in a range from -10 ° C to +55 ° C.

Ð If any questions arise that can not be ascertained with the help of the operating manual, please contact us (contact information, see page 3) or another expert.

!

6S3035

WARNING Ð Technical problems in electrical and mechanical systems

can lead to an unexpected motor start and / or flying parts that can significantly hurt you and others!

Ð Short-circuits of any kind must be avoided! By short-circuit not only parts of the remote control can be destroyed, but depending on the circumstances and the energy content of the batteries there is an acute fire and explosion risk.

Ð All driven by a motor parts such as air and boat propellers, helicopter rotors, open gearboxes are a permanent injury. They must never be touched! A rapidly spinning propeller can cut a finger! Make sure that none and nothing else can come in contact with moving parts!

Ð When the battery is connected or the motor is running: Risk of injury by propeller! Never stand in its danger area!

WARNING Ð Also pay attention while programming the transmitter, make

sure that a connected electric motor does not start up un-intentionally. Disconnect the battery before.

Ð The speed controller and other electronic components should never come into contact with water. The speed con-troller must be protected from dust, dirt, moisture, vibration and foreign parts.

Ð Avoid shock and pressure. Check the speed controller reg-ularly for damages to the housing and cables. Damaged or wet speed controller, even if it is dry again, should no longer be used! Short circuit and fire hazard!

Ð When routing the cables, make sure that they are not in tension excessively bent or broken. Avoid sharp edges, they are a danger to the insulation. Risk of fire!

Ð All cables and connectors must be adequately insulated. Risk of fire!

Ð Do not connect with reverse polarity. Risk of fire! Use po-larized connector system. Avoid short-circuits and blocking the motor.

Ð Never use an AC adapter as power supply! Risk of fire! Ð Do not leave your RC model unattended while it is turned

on. In case of failure, the model could move uncontrollably and cause injury.

Ð The speed controllers are provided solely for the use of battery-powered, radio controlled models, any other use is not allowed. Using a model to transport people is strictly prohibited!

!

!


7S3035

Battery connection

Motor connection

Controller connections

A proper plug, with polarity protection, must be soldered to the battery connection cables. Provide the battery with a con-nection system with polarity protection and always use proper dimension plugs. Do not solder for longer than 5 seconds and after it, be sure that the part can cool without damaging the speed controller.The battery connection cables should not have a total length over 20 cm. ATTENTION Connection to a battery with reverse polarity will destroy the speed controller!

The motor will be connected to the speed controller through three round connectors (G 3,5). The G 3,5 plugs No. 2970 have to be soldered to the motor cables. The three motor cables can alternatively be soldered directly to the speed con-trollers cables.NOTEWhen connecting a sensor motor always pay attention to the wire order. The following connection scheme is mandatory:

ATTENTIONThe connection cables must NEVER be connected in the fol-lowing order:B-A-C, it would cause the immediate destruction of the speed controller!

- C, B, A Configuration

- A, B, C ConfigurationConnection diagram for speed controller and sensor motor

SensorFan

Motor

Telemetry Program Box

Setupbutton

On/Off switch

LED

Battery

Receiver (PPM/SUMD2)

8S3035

Sensor connection

Receiver connector JR plug

Fan connection port

Switch connection port

Setup button

In case of C-B-A configuration you have to set the “Mo-tor-Wiring” in the setting menu to C-B-A to allow the motor to run in the correct direction.

Use the included sensors cable only, pay attention to the cor-rect connection direction and plug it enough to allow a good and stable connection between it and the sensors port.

The three pole cable with JR plug has to be connected to the gas channel port in the receiver. This cable will power the receiver (5,6 V), through the so called BEC system - battery elimination circuit. By the signal cable the speed controller will receive the impulses from the receiver.

Here it is possible to connect an additional cooling fan. When the temperature of the speed controller is under 35°C the fan will be switched off.

To this port is connected the included On/Off switch. If it is not used, the speed controller will automatically switch on when the battery is connected.

Through this button it is possible to set up the settings without programming box or HoTT telemetry and it is even possible to set the gas end points.

Installation in the model and use

Install the ESC in the model so that the cooling surface re-mains free. Provide adequate cooling through generously di-mensioned air intakes.

ATTENTIONIf you do not want to use the controller’s BEC and instead use a separate battery, you must remove and isolate the red wire (+) of the BEC connector as shown in the image. This will prevent a back-flow into the controller, which would destroy it. If you want to connect to the BEC system still an additional battery, you must solder a diode (eg 91505 Schottky diode) on the red wire from the BEC plug, so that current can flow only in the direction of receiver.

CAUTIONIf you also want to connect a battery and controller’s BEC to the receiver, you must necessarily proceed as described above, otherwise the controller will overheat and may burn. Risk of fire and burns!

(+) red

!


9S3035

Throttle stick setting

Ð Switch on (“ON”) the transmitter, then put and hold the gas stick in “neutral” position. Gas and brake should be set at 100% in the transmitter settings.

Ð Connect the battery to the speed controller with the correct polarity. Switch the speed controller on. If all the connection cables are connected properly, the motor will produce a short beep, to indicate that the system has been powered on.

Ð Push the set button just for longer than 1 second. The green LED will flash. When the button is released the green LED will light on and the gas position is then saved.

Ð Then move the stick to full gas. The red LED lights on. Full gas position is then saved.

Ð Move the stick to the full brake position. Both LEDs will light on, full brake position is then saved.

Ð Bring the stick to the neutral position. The red and green LEDs will then flash to indicate that the throttle stick setting procedure has finished.

NOTEThis initial setting of the throttle lever is only necessary if you use another transmitter, or if the settings have been changed.

10S3035

Programming without HoTT transmitter

1. Switch on the transmitter and move the gas stick to the neutral position.

2. Connect the battery and switch the speed controller on.3. Push and hold the set button for longer than 3 seconds.

Firstly only the green LED will flash, after 2 seconds the red one will do the same.

4. Release the button and the red LED will flash once. It means that the menu point 1 “motor type” has been se-lected (see table on the left). By pushing the gas stick to full gas position and releasing it to neutral position you will move to the next menu point (eg program point 2: battery type; the red LED will then flash twice). There are in total 20 menu points to choose, for each one of them the LED will flash indicating the respective number.

5. Hold the gas stick to the full gas position for longer than 4 seconds to open a menu point. Then both led will flash showing the actual setting. Move the gas stick to full brake and soon to full gas to increase the parameter value of 1. Repeat this operation until you reach up for the wished value.

6. To come back to the menu points, leave the gas stick in neutral position for about 4 seconds.

7. Then you can move to the next menu point (as described in point 4), or you can simply leave the program menu and come back in stand-by mode by briefly pushing the set button.

8. The speed controller is then ready for use.

The program points from 20 to 37 of the following list can be setted only by using a Graupner HoTT transmitter or the pro-gram box No. S8272.

Programming with the program box

To use the program box No.S8272 (included in S3035.1 only) read the included manual.

# Program point

L E D flashes x times

1 Select Mo-tor Type

1

2 Select Battery

2

3 Cut Off Voltage

3

4 Power Curve

4

5 Advance Timing

5

6 Accelera-tion

6

7 Start Power 78 Start Cur-

rent Limit8

9 Current Limit

9

10 Reverse Function

10

11 Reverse Delay

11

12 M-Reverse Amount

12

13 Neutral Width

13

14 Motor Di-rection

14

15 Speed Mi-xing Brake

15

16 A.B.S Bra-ke

16

17 Auto Brake Amount

17

18 Minimum Brake

Amount

18

19 Maximum Brake

Amount

19

20 Factory Setting

20


11S3035

Power Curve

Advance Timing

AccelerationStart Power

Start Current LimitCurrent Limit

Reverse FunctionReverse Delay

Max-Reverse AmountNeutral Width

Motor DirectionSpeed Mixing Brake

A.B.S BrakeAuto Brake Amount

Minimum Brake AmountMaximum Brake Amount

Cut Off TempCut Off M-Temp.B.E.C. VoltageCurrent VoltageCurrent Temp

Max TemperatureMotor Temp.

Motor Max Temp.Max Current.

Motor Pole Num

4

5

67891011121314151617181920212223242526272829

5 0°5

5Lowest

OffOff

One Way2.5s30%Wide

Normal0%Off0%0%

100%120 °100 °6.0V

------

4 Pole

Cut Off Voltage

Program pointNo. Parameter StandardSensorless (1) Sensored (2)

LiPo(1) LiFe(2) NiMH (3)

0(1) ~ 10(11)

0(1) ~ 10(11)Lowest(1) Low(2) Normal(3) High(4) Highest(5)

Off(1) 10% (2) ~ 100% (11)Off(1) 10% (2) ~ 100% (11)

One Way(1) Two Way(2) Two Way2(3) Two Way3(4)Off (1) 0.2s(2) 0.5s(3) 0.8s(4) 1.3s(5) 1.8s(6) 2.5s (7)

20%(1)~100%(9)Narrow(1) Normal(2) Wide(3)

Normal(1) Reverse(2)Sensored: 0%(1)~ 100%(11)

Off(1) Weakest(2) Weak(3) Normal(4) Strong (5) Strongest(6)0 % (1) ~ 100% (11)0 % (1) ~ 100% (11)0 % (1) ~ 100% (11)

100℃~Disable (only available by program box)100℃~Disable (only available by program box)

5.0V~8.0V (only available by program box)Battery voltage

Speed controller temperatureMaximum controller temperature during use

Actual motor temperatureMaximum motor temperature during useMaximum current of the speed controller

Setting motor poles 2 poles ~ 20 poles ESC

SENSORED

SENSORLESS 0°(1) ~ 25°(6)0(1) ~ 5(6)

6~10 (only available by program box)

For values see table below3

1

2

Select Motor TypeSelect Battery

SensoredLiPo

Disabled(1) Auto(2) V(3) ~ V(12) Auto -Cutoff Voltage Auto

33

Error HistoryDown Load

Restore MemoryBackup MemoryFactory Setting

Maximum speed ESC Average speed during use

Gear Ratio

Tire Diameter

Motor-Wiring

30

31

32

Maximum Speed34 Average Speed3536373839

1.0:1

110mm

A-B-C-------

Setting gear ratio 1:0:1~15.0:0:1(only available by program box)Setting tire diameter 400~200

(only available by program box)Setting motor cable connection A-B-C or C-B-A

(only available by program box)

Errors listLoad parameters from ESC

Load the program box data in the ESCSave ESC data in the program box

Reset to factory settings

Settable values in program

Cut off voltage list (LED flashes respectively)LEDLiPoLiFeNixx

3x6.6V6.6V6V

4x7V

7.5V6.3V

5x9.9V8.8V7V

6x10.5V10V7.7V

7x13.2V11V8.4V

8x14V

12.5V9.1V

9x16.5V13.2V9.8V

10x17.5V15V

10.5V

11x19.8V15.4V11.2V

12x21V

17.5V11.9V

12S3035

Special featuresAdvanced TimingIf the Advanced Timing value is reduced, then also the power consumption and the temperature of the motor are reduced. The maximum speed and the acceleration decrease too, the battery life increases.If the Advanced Timing value is increased, then increases the power consumption and the temperature of the motor. Max-imum speed and acceleration increase and the battery life decreases. To increase the maximum speed we recommend the use of a different gear ratio. If the value is 0, the controller is in the 0-Boost mode and is thus correspondingly 0 Boost compliant. This is signaled by a flashing green LED in neutral position.Acceleration Influences the acceleration of the motor. A lower value means a slower motor acceleration, a higher value means more pow-er.Start Power Used as launch control, it can make start much easier to han-dle.Power CurveIt affects the proportionality in gas control. A lower value makes gas more docile and controllable, a higher value makes the gas more aggressive.Reverse functionTwoWay: Reverse with settable delay (off – 2.5 sec)TwoWay2: regardless of Reverse Delay setting, after motor stopped and 1sec, reverse function will get output. (Max. 6~7sec, direction will be reversed)TwoWay3: If Trigger of Radio is moving from forward to back-ward movement, then ESC will give the Break to motor , and Motor will be stopped.If they are in same position, Reverse function is not working.In order to use Reverse function, Trigger of Radio should move to Neutral position, and go to Backward movement, then you could use reverse function normally.Telemetry function Values as the components temperature, speed and voltage so as the error protocol can be read on the program box.Checking possible through TX, RX for Cars, such as Graupner HoTT X-8E, X-8N.

NOTEIf during use there should be a problem caused by sensor, the speed controller will switch automatically from sensor to sensorless!


13S3035

LED error messages

• (R) No receiver signal - the red LED flashes 1x/sec

• (V) Low battery voltage - the red LED flashes 2x/sec

• (S) Sensor problem - the red LED flashes 3x/sec

• (T1) Speed controller temperature too high - the red LED flashes 4x/sec

• (M) Motor problem - the red LED flashes 5x/sec

• (T2) Motor temperature too high - the red LED flashes 6x/sec

LED Status display

Gas position green LED red LEDNeutral on offNeutral (0-Boost) flashes offFull gas off onFull brake on on

ESC Data View in telemetry menuTelemetry dataDisplay on a Graupner / SJ HOTT transmitter

Current: MAX, Actual currrent

Volt: MIN, Actual voltage

ESC: MAX temp Actual temperature

MOTOR:( motor temp.) MAX temp. , Actual temperature

SPEED(MAX): MAX SPEED(KM/H) Maximum speed

SPEED(AVG): AVG SPEED(KM/H) Average speed

ERROR : M T1 T2 V R S (see errors list above)

[ESC] DATA VIEW <> Curr : 5.3Max 3.0A Volt : 7.5Min 7.6V ESC : 29°Max 28°C

MOTOR : 29°Max 28°CSPEED(MAX):000.0km/h SPEED(Avg):000.0km/h ERROR : M T1 T2 V R S

14S3035

Depending on the motor type you choose, sensor or sensore-less, there are different setting options and displays.

Programming with HoTT transmitter

The settings of GM GENIUS ULTRA +T 180A TELEMETRY SPEED CONTROLLER are included in the receiver settings. Read the transmitter manual, specially the “telemetry” section. The set-tings are available in the “Telemetry” under the menu point “Settings/displays”.NOTEThe menus are available only if receiver and speed controller are switched on! Before the menu can be available and set-tings can be changed it may take a few seconds after switch-ing the receiver on. Displays for speed controller settings:

Sensorless Motor Sensor Motor

[E.S.C] *SENSORLESS > User setup : page 1>MODEL :SENSORLESS E.S.C save? No Factory set? No

Ver:P 2.080

[E.S.C] *SENSOR<> User setup : page 1>MODEL : SENSOR E.S.C save? No Factory set? No

Ver:P 2.080

[E.S.C] *SENSORLESS > >User Setup : Page 2 Battery : LiPo Cut_off V. : Auto Pwr Curve : 5 Advance T. : 0

[E.S.C] *SENSORLESS > >User Setup : Page 3Acceleration : 5 Start power : Lowest St.curr.Limt : 0 % curr.Limt : 0 % reverse func : oneway Rev.Delay : 2.5 s

[E.S.C] *SENSORLESS > >User Setup : Page 4Max-reverse : 30 % Neutral W. : Wide Direction : Normal A.B.S Breake : off Auto-Brake : 0 %

[E.S.C] *SENSOR<> >User Setup : Page 2Battery : LiPo Cut_off V. : Auto Pwr Curve : 5 Advance T. : 5Turbo T. : 0

[E.S.C] *SENSOR<> >User Setup : Page 3Acceleration : 5 Start power : LowestSt.curr.Limt : off curr.Limt : off reverse func : onewayRev.Delay : 2.5 s

[E.S.C] *SENSOR<> >User Setup : Page 4Max-reverse : 30 % Neutral W. : WideDirection : NormalSpe.Mix.Brak : 0 % A.B.S Breake : off Auto-Brake : 0 %

[E.S.C] *SENSORLESS > >User Setup : Page 5Min-Brake : 0 % Max-Brake : 100 % Number-pole : 4 Gear Ratio : 1.0:1 Tire dim : 110 mm Bec volt : 6.0V

[E.S.C] *SENSOR<> >User Setup : Page 5Min-Brake : 0 % Max-Brake : 100 % Number-pole : 4 Gear Ratio : 1.0:1 Tire dim : 110 mmBec volt : 6.0V

[E.S.C] *SENSORLESS > >User Setup : Page 6 ESC CutOff : 120°C

[E.S.C] *SENSOR<> >User Setup : Page 6ESC CutOff : 120°C

MOTOR CutOff : 100°CMOTOR Wiring : A-B-C

Units : Metric

Units : Metric

1

2

3

4

5

6


15S3035

Model (Motor type)Here you can choose the type of motor (sensorless = without sensor; sensor = with sensor)

Battery (battery type)Here you can select the type of battery LiPo / LiFe / NiM-h(NiCd).If the battery type is changed, the battery cut-off mode will be automatically changed in AUTO. To select the correct bat-tery type is extremely important, otherwise the battery can be damaged.

Cut-off V. (low voltage battery cut-off)Here you can set the low voltage threshold by which the con-troller will cut the current.Disable/Auto/6.0~23.0V(0.1V Step)If the battery type is changed, the cut-off will turn in to AUTO mode. The AUTO mode depends on the controller model.

PWR Curve (power curve)here you can set the power curve. 0 ~ 10Through this function you can set the power modulation and the throttle curve.(Similar to the exponential function in transmitter)

Advance TimingIf the Advanced Timing value is reduced, then also the power consumption and the temperature of the motor are reduced. The maximum speed and the acceleration decrease too, the battery life increases.If the Advanced Timing value is increased, then increases the power consumption and the temperature of the motor. Max-imum speed and acceleration increase and the battery life decreases. To increase the maximum speed we recommend the use of a different gear ratio. If the value is 0, the controller is in the 0-Boost mode and is thus correspondingly 0 Boost compliant. This is signaled by a flashing green LED in neutral position.

Acceleration (acceleration and soft gas)Here you can set the acceleration value. 0 ~ 10Through this function you can set how fast the motor response will be to the throttle.It affects the motor speed. EA lower value means a slower motor acceleration, a higher value means more power.

Start power (start power)Here you can set the start power.

1

2

30~10

0.35s~0.2s0.35s~0.1s

ModeSensorlessSensored

HIGHEST16.6%30%

LOWEST0%0%

LOW4%

8.3%

NORMAL8.8%15.6%

HIGH12.7%23%

ModeSensorlessSensored

16S3035

Lowest / Low / Normal / High / Highest.Though this function you can set the minimal start power, when the motor turns. It can be associated to a minimal gas quantity.

St.curr. Limit (start current limit)Here you can set the start current limit. Off / 10% ~ 100%Used as a launch control, It can simplify starts. With optimal setting this function can eliminate the wheel slipping during start. The value depends on many model specifications. “OFF” allows the maximum power. The start current limit is activated by holding the gas stick in neutral or brake position for longer then 10 seconds. It is deactivated when the motor turns and the gas stick comes back to neutral position.

curr. Limit (current limit)Here you can set the current limit. Off / 10% ~ 100%By using this function you can reduce the torque of your mo-tor and make your model easier to control.

reverse func (reverse function)Reverse gear on/off.One Way: Functions: forward/brakeTwo Way 1: Functions: forward/brake/reverse. The reverse gear will be automatically activated after the reverse delay. During this delay the brake is active.Two Way 2: Functions: forward/brake/reverse. If the stick on the transmitter is moved and the motor rotates, then the brake is activated. If the motor does not rotate and the stick is moved to the brake direction, then the reverse function is activated. At the latest after 6 seconds of braking the reverse function is activated in any case, even if the motor is still rotating.TwoWay3: Functions: forward/brake/reverse.The reverse is possible only when the throttle stick is moved from forward to brake position and then set back to neutral. Pushing the throttle to brake position activates then the re-verse.

Rev.Delay (reverse gear delay)Here you can set the delay before reverse gear, Off / 0.2s / 0.5s / 0.8s / 1.3s / 1.8s / 2.5s. The reverse gear delay is the time lapse after which the reverse is activated. After that the reverse is active.

Max-reverse (maximum reverse speed)Here you can set the maximum reverse speed, 20% ~ 100%.The maximum reverse speed determines the maximum pow-er that is available when driving in reverse and permits reduc-

3


17S3035

tion of the acceleration and speed when driving in reverse in mode Two Way 1, 2, 3.

Neutral W. (neutral point width)You set the width of the neutral point here: narrow, normal, wide The neutral point width is the region around the neutral position of the transmitter joystick and, depending on the me-chanical play of the transmitter joystick, can be adjusted.

Direction (motor rotation direction)Here you can set the motor rotation direction. Normal / Re-verse.

Spe.Mix.Brk. (speed mixing brake)This function equalizes the normally different brake power in high and low speeds, so that the brake power has always the same strength.

A.B.S. Brake (Anti-lock braking system)Here you can set the A.B.S. brake function.Off/ Weakest/ Weak/ Normal/ Strong/ Strongest. You set ABS braking OFF here or the strength that you need at the full braking position.

Auto Brake (automatic brake)Using the INC & DEC buttons, set the automatic braking ef-fect 0 ~ 100%.Set the automatic braking effect for the neutral position.Practical values: 0~30% (crawler: 40~100%).

4

18S3035

Min-Brake (minimum braking effect)Using the INC & DEC buttons, here you can set the automatic brake: 0 ~ 100%.Set the minimum braking effect. (Practical values: 0 ~ 40%) (Braking range: minimum braking effect ~ maximum braking effect).

Max-Brake (maximum braking effect)Here you can set the maximum braking effect: 0~100%.Set the maximum brake for the “Full brake”- position. (Practical values: 70~80%) (Braking range: minimum braking effect ~ maximum braking effect).

Example for brake setting Min-Max Brake

-10

10

30

50

70

90

110

-100 -80 -60 -40 -20 0

Brake e�ect (%)

Gas stick brake percent. (%)

Example: Min. Brake=20, Max.Brake=90

Number-pole (number of motor poles)Here you can set the number of motor poles: 2 ~ 20. Set the number of motor poles (on car motors, at least 2) so that the maximum and average speed of the most recent operation can be displayed.

Gear Ratio Here you can set the overall gear reduction ratio: 2.0:1 ~ 15.0:1.Set the overall gear reduction ratio so that the maximum and average speed of the most recent operation can be displayed.

Tire Diameter (tire diameter)Here you can set the tyre diameter: 40 mm ~ 200 mm.Set the tyre diameter so that the maximum and average speed of the most recent operation can be displayed.

Bec volt (controller BEC voltage)Here you can set the controller BEC voltage, 5 - 8V

5


19S3035

ESC CutOff (controller cut-off temperature)Here you can set the maximum temperature of the speed controller. Disable (cutoff not active) / 100°C ~ 135°C On reaching the maximum set temperature, the controller cuts off.

Motor CutOff (motor cut-off temperature)Here you can set the maximum temperature of the motor. Disable (cutoff not active) / 100°C ~ 135°C On reaching the maximum set temperature, the controller cuts off.

Motor WiringHere you can set the motor cable connection order, in case you connected them in wrong order. (see the paragraph “speed controller connections”)

Units Here you can set the measure units, metric or English (eg Celsius / Fahrenheit).

Warning messages

Display in telemetry menu

Settable warning messages

Acustic and visual warning messages

[ESC] WARNING <> >Set warning : page 1E.S.C save? No Factory set ? No

Ver:P 2.080

[ESC] VOLTAGE <> >set warning : page 2Voltage : 3.0V Warning Time : off Repeat Time :ALWAYS Signal Tone : P

Min-volt : 7.5V

[ESC] E.S.C.TEMP. <> >set warning : page 3Temperature : 60°CWarning Time : off Repeat Time : ALWAYS Signal Tone : H

ESC. Temp. : 29°C

[ESC] MAX.CURRENT <> >set warning : page 5maximum cur : 100A Warning Time : off Repeat Time :ALWAYS Signal Tone : W

MAX.CURR : 5.3A

[ESC] MOTOR TEMP. <> >set warning : page 4Temperature : 60°CWarning Time : off Repeat Time :ALWAYS Signal Tone : I

MOTOR Temp. : 29°C

[ESC] WARNING <> >set warning : page 3 Temperature : 60°CWarning Time : off Repeat Time :ALWAYS Signal Tone : H

ESC. Temp. : 29°C

Controller settings can be modified

directly through the transmitter.

[ESC] *SENSORLESS <> User setup : page 1 >MODEL :SENSORLESS E.S.C save? YesFactory set? YesE.S.C RESTART... 3

Ver:P 2.080

E.S.C] *SENSORLESS > User setup : page 1 >MODEL :SENSORLESSE.S.C save? No Factory set? No

Ver:P 1.000

E.S.C] *SENSOR > User setup : page 1 >MODEL : SENSORE.S.C save? No Factory set? No

Ver:P 1.000

6

20S3035

Programming warning thresholds

Minimum voltage (Page 2)Minimum Voltage: Warning threshold for the minimum battery voltage, set between 3.0 and 23 VFactory setting: 3.0 V, Signal Tone: PWarning OFF

Maximum controller temperature (Page 3)Maximum ESC Temperature: Warning threshold for the maxi-mum ESC temperature, set between 10 and 120°C.Factory setting: 100°C, Signal tone: HWarning Off

Maximum motor temperature (Page 4)Maximum MOTOR Temperature: Warning threshold for the maximum MOTOR temperature, set between 10 and 120°C.Factory setting: 100°C, Signal tone: IWarning Off

Maximum current (Page 5)Maximum Current: Warning threshold for the maximum cur-rent of the drive motor, set between 25 and 200 A.Note: the warning threshold should never be set to a higher value than the maximum permissible current for your speed controller type, as this would prevent sensible warnings being generated!Factory setting: depending on speed controller, Signal tone: WWarning Off

Saving of the warnings and thresholds

To save the settings in the speed controller, go back in the Display “page 1 - ESC MODEL” and select the menu point “E.S.C save”. By pushing the SET button you highlight the parameter (black background). Change to YES and press the SET button, to save the selected settings. An additional line “E.S.C RESTART” now appears on the screen and counts down starting at 3. The settings are permanently saved when the count reaches 0; “E.S.C RESTART” disappears again to confirm this. If you do not want to save the changes, select NO.

NOTEThe motor will not start if you alter settings but do not store them. This is an additional safety function to ensure that you do not overlook the ‘saving’ procedure.

[ESC] *SENSOR <> >User setup :>MODEL : E.S.C save? Factory set? E.S.C RESTART...

>Ver:P 2.080

page 1SENSOR

YesYes

0

[ESC] VOLTAGE <> >Set warning : >Voltage :>Warning Time: >Repeat Time :>Signal Tone :

>Min-Volt :

page 26.0Voff

ALWAYS P

7.5V

[ESC] E.S.C.TEMP. <> >Set warning : >Temperature :>Warning Time: >Repeat Time :>Signal Tone :

>ESC. Temp :

page 360 C5sec

ALWAYS H

29 C

[ESC] MOTOR TEMP. <> >Set warning : >Temperature :>Warning Time: >Repeat Time :>Signal Tone :

>MOTOR Temp :

page 4100 C5sec

ALWAYS I

29 C

[ESC] MAX. CURRENT<> >Set warning : >Maximum cur :>Warning Time: >Repeat Time :>Signal Tone :

>MAX.CURR :

page 5100A5sec

ALWAYS W

5.3A


21S3035

Graphic display of telemetry data

For information on displaying telemetry data please read the instructions supplied with your radio control system or SMART-BOX.This screen displays the data generated by a GM GENIUS UL-TRA +T 180A. Key, reading from top right:

Value Explanation

V

Left-hand value: actual battery voltage

Right-hand value: actual battery voltage in present power-on period

Temp.°C

Upper parameter: speed controller lower parameter: motor (only if supported, otherwise 0)

Left-hand value: actual speed controller temperature

Value in brackets: maximum controller temperature in present power-on period

mAh Battery capacity consumed

ACentre and bar display: actual current

Right-hand value: maximum current in present power-on period

rpm

Centre an bar display: actual rotation speed of the motor connected to the ESC

Right-hand value: maximum rotational speed in present power-on period

Rpm displayThis screen displays the current rotational speed of the mo-tor connected to the brushless speed controller. The correct speed is displayed only if the values, as motor poles, have been selected properly.

RX–S QUA: 100%RX–S ST : 100%

TX–dBm: 33dBmRX–dBm: 33dBm

RX–SPG.:4.8 TMP

V–PACK: 10ms

CH OUTPUT TYPE:ONCE

RECEIVERGENERAL

ELECT. AIRVARIO

GPSAIR ESC

0 00rpm

0.0A 0.0A00mAh

0( 0)°C0.0V/ 0.0V

0( 0)°C

U/min0

0 0

22S3035

Technical data

GM GENIUS ULTRA +T 180ANo. S3035

Cell count (LiPo) 2 - 6

Cell count (NiMh) 8 - 18

Operating voltage 7,4 - 22,2V DC

Current 180 A

Frequency PWM 32 kHz

BEC current 3 A

BEC peak current 10 A

BEC voltage 5 - 8V

Motor run cut-off Yes

Overheating cut-off Yes

Under voltage cut-off Yes

Dimensions (mm) 40 x 56 x 35,6

Weight (with connection cables) 92 g


23S3035

+7168.6

+7168.S

Firmware Update

The user can use the update facility to maintain the speed controller of the GM GENIUS ULTRA +T 180A always at the latest state of development and ensure that additional functions can be added in the future.General PreparationTo update, you need a Windows PC and the grStudio firm-ware upgrade software. This can be downloaded from our website. Open the item page for your controller and click on the Downloads tab.Under the item PC Update software, you will now find the re-quired file. After it has been downloaded, it must be extracted.1. USB driver installed? (The driver is located in the “HoTT_PC_Software” software package) 2. Select the COM port 3. Start the “Speed controller” program In the “Device” program group, start the “Speed controller” program. (Alternatively, se-lect the appropriate entry under “Menu”.)

4. Disconnect the speed controllerDisconnect the controller from the receiver, the power supply and a motor.5. Connect the speed controller to the PCRequired accessories:• USB interface for Graupner/GM-GENIUS 7168.6• USB interface adapter cable for HoTT Sensors/Manager

7168.S• Operating battery

Connect the interface adapter (No.7168.6) to the USB cable and then connect the USB cable to the computer. An LED on the interface adapter should glow red, otherwise, check Step (1.). (Depending on the operating system, the LED goes out after a certain period of time).Disconnect the 3-wire connection cable of the speed con-troller from the receiver. Connect the 2 wire end of the adapt-er cable (No. 7168.S) to the telemetry jack (see p. 7) on the speed controller.

24S3035

Now connect an operating battery (do not exceed the max. permissible operating voltage!) to the appropriate connections on the controller. However, do not yet switch on the controller by means of the ON/OFF switch on the controller. You now have two ways of loading the firmware file:“Load automatically” or “Open file”.

If you wish to transfer the current firmware to the controller automatically, use the “Load automatically” option. The ap-plication will then attempt to download the current firmware over the Internet.The bar begins to fill in green immediately after you click the on-screen button.Switch on the controller at the switch before the bar fills. An additional dialogue field opens in which you can click on the desired firmware and then on the “Open file” on-screen but-ton. The application then downloads the file and transfers it to the controller. If you wish to transfer special firmware that you have in the form of a file to the controller, use the “Open file” option. In the dialogue that then opens, select the previously downloaded file; the bar then begins to fill in green. Switch on the controller at the switch before the bar fills; the application will then transfer the firmware.Detailed update instructions for HoTT components can be found on our home page in the download section for the par-ticular item.


25S3035

Declaration of conformity

14

EU-KonformitätserklärungEU-Declaration of Conformity

Hiermit bestätigen wir, dass das nachfolgend bezeichnete Gerät den angegebenen Richtlinien entspricht.We herwith confi rm that the following appliance complies with the mentioned directives.

Artikelbezeichnung:Article description:

Artikelnummer:Article number:

Firmenanschrift:Company adress:

Einschlägige EU-Richtlinien / Governing EU-directives / Directives CE concernées :

1. Elektromagnetische Verträglichkeit (EMV) 2. Niederspannungs-Richtlinieevitcerid egatlov-woL )CME( ytilibitapmoc citengamortcelE

CE/59/6002 CE/801/4002 3. Maschinenrichtlinie 4. Medizinprodukte (Klasse 1)

)1 ssalC( evitcerid ecived lacideM evitcerid enihsaMCEE/24/39 CE/24/6002

5. Funkanlagen u. Telekommunikationseinrichtungen 6. Ökodesign-Richtlinie)PrE( evitcerid stcudorp detaler ygrenE tnempiuqE lanimreT noitacinummoceleT .a oidaR

CEE/521/9002 CE/5/9991 ETT&R 7. Beschränkung der Verwendung bestimmter gefährlicher Stoffe in Elektro- und Elektronikgeräten

Restriction of the use of certain hazardous substances2011/65/EC

Harmonisierte EN-Normen / Harmonised EN-Standards

Der Artikel entspricht folgenden, zur Erlangung des CE-Zeichens erforderlichen Normen:The article complies with the standards as mentioned below which are necessary to obtain the CE-symbol:

Zu 1:EN 61000-6-3:2007+A1:2011EN 61000-6-1:2007

Graupner|SJ GmbHHenriettenstrasse 96D-73230 Kirchheim/Teck

Unterschrift / Signature

rotceriD gniganaM / rerhüfstfähcseG noitisoP

Ausstellungsdatum / Date of issue

GM Genius Ultra 180 +T

S3035

22.04.2015

26S3035


27S3035

28S3035

The present construction or user manual is for informational purposes only and may be changed without prior notice. The current version can be found on the Internet at www.graupner.de on the relevant product page. In addition, the com-pany Graupner/SJ GmbH has no responsibility or liability for any errors or inac-curacies that may appear in construction or operation manuals. No liability can be accepted for printing errors.

Notes for environmental protection

DISPOSAL NOTESThis symbol on the product, user manual or packaging indi-cates that this product must not be disposed of with other household waste at the end of its life. It must be handed over to the applicable collection point for the recycling of electrical and electronic equipment.The materials are recyclable as marked. By recycling, material reusing or other forms of scrap usage you are making an im-portant contribution to environmental protection.Batteries and accumulators must be removed from the device and disposed of at an appropriate collection point. Please in-quire if necessary from the local authority for the appropriate disposal site.

Care and maintenance

Care notesThe speed controller is maintenance-free and requires no maintenance. However, please protect it in your own interest from dust, dirt and moisture!Before cleaning the speed controller disconnect the battery and use only a dry cloth (no cleaning agents!).

Warranty

The Graupner/SJ GmbH, Henriettenstrassee 96, 73230 Kirchheim / Teck grants from the date of purchase of this product for a period of 24 months. The warranty applies only to the material or operational defects already existing when you purchased the item. Damage due to wear, overloading, incorrect accessories or improper handling are excluded from the guarantee. The legal rights and claims are not affected by this guarantee. Please check exactly defects before a claim or send the product, because we have to ask you to pay ship-ping costs if the item is free from defects.

P

s3035 gm genius ultra +t 180a en - graupner · s3035 gm genius ultra +t 180a Ð switch cable,...

Documents