rp-102 - vitus audio · rp-102 | version 1 7 1. getting started 1. getting started figure 1 box...

RP-102Owner’s Manual

2 RP-102 | Version 1

All rights reserved. No part of this publication may be reproduced, stored in or introduced into a retrieval system, or transmitted in any form, or by any means (electronic, mechanical, photocopying, recording or otherwise) without the prior written permission of Vitus Audio. Any person who does any unauthorized act in relation to this publication may be liable to criminal prosecution and civil claims for damages.

Information contained in this manual is subject to change without notice, and whilst it is checked for accuracy, no liabilities can be accepted for errors.

3RP-102 | Version 1

table of contents

on a personal noteCertificate . . . . . . . . . . . . 4

from the creatorForeword . . . . . . . . . . . . . 5

introduction About this manual . . . . . . . . 6Introduction to the Reference Series . . . . . . . 6Unpacking the box . . . . . . . . 7What’s in the box . . . . . . . . . 7About the RP-102. . . . . . . . . 8External interference. . . . . . . 8

2. connectingTurning the RP-102 on and off. . 9RP-102 rear panel. . . . . . . . . 10Connecting the RP-102 . . . . . 10

3. operationOperation modes . . . . . . . . 12Functions – left front panel . . . 13Functions – right front panel . . 14RP-102 Menu: introduction . . . 15RP-102 Menu: description of the elements. . . . . . . . . . . . 16RP-102 Menu: tree diagram . . . 17

4. operation & serviceSafety notice . . . . . . . . . . . 18Mains supply voltage . . . . . . 18Maintenance . . . . . . . . . . . 18Mains fuses . . . . . . . . . . . . 18Replacing a blown fuse . . . . . 19Replacing a blown fuse continued . . . . . . . . . . . . . 20

5. warrantyWarranty . . . . . . . . . . . . . 21

6. specificationsRP-102 Measurements . . . . . . 24RP-102 Specifications . . . . . . 25Gain values. . . . . . . . . . . . . 26Load values . . . . . . . . . . . 27

7. examples operatingExample 1 . . . . . . . . . . . . 28Example 2 . . . . . . . . . . . . 29Example 3 . . . . . . . . . . . . 30Example 4 remote . . . . . . . . 31Example 4.1 . . . . . . . . . . . 31Example 4.2. . . . . . . . . . . . 31Example 4.3 . . . . . . . . . . . 32Example 5 . . . . . . . . . . . . 33Example 6 . . . . . . . . . . . . 34Example 6.1 . . . . . . . . . . . . 35

7. examples connecting devicesConnecting devices . . . . . . . 36

8. picturesRP-102 Front . . . . . . . . . . . 37


on a personal note

Certificate

Model: RP-102

Product ID/Serial

__________________________________

Product Build Date

__________________________________

Signed

__________________________________

All products details, specifications and measurements are recorded for your RP-102 and kept by Vitus Audio.

5RP-102 | Version 1

from the creator

ForewordFirst of all, thank you for choosing the Vitus Audio RP-102 Phonostage, we are sure you will enjoy it for many years to come. When purchasing a Vitus Audio product, you are guaranteed a musical performance,which exceeds the current musical standards. Vitus Audio is dedicated to musical performance rather than technical details and high performance measures. We believe that many manufactures are blinded by the current available theory, instead of looking for new answers.

At Vitus Audio everything works until proven not to. This way we always try to push the limits and explore the unexplored. As a result of this, many of the solutions we use today are considered to be “impossible to ever get working”, however they have convinced many people and reviewers world wide of the opposite. Before any of our new topologies are implemented in our products, they are carefully reviewed by our dedicated listening panel. This way we can guarantee the correct level of musically performance and robustness.

Generally we’re after super neutral, super detailed and super dynamic reproduction without “loosing” the nerve in the music which often is a drawback of many high end amplifiers. Our real strongholds are complete silence, unbelievable depth and width in the soundstage resulting in a far more open sound with higher resolution -you could say, closer to the artist. As a result of the above, our amps do not “focus” on any specific frequencies - i.e. no extension of top or bass, which of course results in high clarity of the midrange since it’s “naturally present”!

Hans Ole Vitus


introduction

About this manual

This is your RP-102 owner’s manual. The following pages will describe, as clearly as possible, how to get your RP-102 operating fast and simple. Although some operations are self-explanatory, we strongly suggest you read this manual to avoid any damage to the unit. The manual is designed to be helpful. If there are points you feel we could cover better, or that we have missed out – please tell us.

Important information is presented like

this. Ignoring this information may cause damage to you or the unit. Damage caused to the unit by ignoring this information might invalidate the warranty.

Introduction to the Reference SeriesThe Vitus Audio Reference Series is a true high-end series of products, which is build on our true dedication to neutral music reproduction. Every detail is carefully thought through, and all choices made during development, where based purely on listening, and not measuring. Only the best available materials are used to ensure an overall quality which will last for many years, when treated right.

7RP-102 | Version 1

1. getting started

1. g

ett

ing

sta

rte

d

Figure 1 Box exploded view

Foam top 1

Optional MAC Remote

Foam bottom

Box

Foam top 2

Foam Sides6 pieces

RP-102

USB with Manual & Brochure

Power Cable

Power Supply

Unpacking the boxAfter you have opened the top, it is possible to remove the top protective foam which gives you direct access to the unit. In the top you will find the remote, the power cord and brochures. Now remove the side protective foam, this will make it easier to grab hold of the RP-102. Two people carefully lift the unit out of the box, and put it directly onto the floor.Store the empty box and the protective foam for later use.

What’s in the boxRP-102Power SupplyPower CableOptional MAC Remote

USB with Manual & Brochure

Foam top 1Foam top 2Foam Sides 6 piecesFoam bottomBox


1. getting started

About the RP-102The new RP-102 is the successor of the RP-100. The powersupply of the RP-102 is based on the technology developed for out Signature and Masterpiece Series, and it offers supperior performance over any battery driven power supply.

Cartridge loading is set directly from the front of the phonostage - or by a MAC remote which can be purchased seperately. The RP-102 offers direct switchable impedances from 40 Ohm to 47 kOhm without having to access the rear panel or to open the phonostage for making hardware changes.

The RP-102 is equipped with both RCA and XLR inputs and outputs for optimal compatability with any system configuration.

External interferenceIt is important to remember that all equipment which is connected to the mains is a potential source of hum and interference and may radiate both electrostatic or electromagnetic radiation. In addition, the mains will also act as a carrier for many forms of RF interference generated by electric motors, air-conditioning units, thyristor light dimmers etc. Unless the earth system is clean, all attempts to improve hum noise levels will be futile. In extreme cases there will be no alternative but to provide a completely separate and independent `technical earth' to replace the incoming 'noisy earth'. However, always consult your local electricity supply authority to ensure that safety regulations are not being infringed.

9RP-102 | Version 1

2. connecting

2. c

on

ne

ctin

g

Turning the RP-102 on and off

Always turn on the products beginning from the source:

Phonostage a Preamplifier a Power Amplifier

Always turn off your products in reverse order:

Power Amplifier a Preamplifier a Phonostage

Not following this procedure,may cause damage to any of your products/speakers. Damage caused to any of your products/speakers by not following this procedure will invalidate the warranty.

RP-102 rear panel

InputsInput 1 RCA

Input 2 XLR

Power

OutputsOutput 1

Output 2

Ground

Figure 3 Plugs

Ground

XLR out

PowerPSU

RP-102 Power

XLR in

RCA

RCA

Connecting the RP-102Grounding the turntable It is important that you connect your turntable to the ground terminal (GND) on the back of the RP-102. If you don't connect your turntable to the ground terminal then you might experience hum.


2. connecting

Connecting the InputsPlace the RP-102.Connect all the sources to the inputs of the RP-102, labelled INPUT 1 and INPUT 2 on the rear panel.

Connecting the OutputsConnect the outputs of the RP-102. After you have connected both inputs and outputs you can connect the mains to the phonostage.

Figure 2 GND

RP-102 rear panel

Input 2Input 1

Right

Input 2Input 1

Left

Output - one Output - two

MODEL RP-101 VOLTS 50 / 60 Hz100 115 230

SERIAL No.

MAINS

GND/EARTH

NEU

TRIKPU

SH

NEU

TRIKPU

SH To prevent re and shock hazard, do not expose this device

to rain and moisture

WarningRisk of electrical shock

DO NOT OPENNo user serviceable parts inside

Warning

Input 2Input 1

Right

Input 2Input 1

Left

Output - one Output - two

MODEL RP-101 VOLTS 50 / 60 Hz100 115 230

SERIAL No.

MAINS

GND/EARTH

NEU

TRIKPU

SH

NEU

TRIKPU

SH To prevent re and shock hazard, do not expose this device

to rain and moisture

WarningRisk of electrical shock

DO NOT OPENNo user serviceable parts inside

Warning

Figure 4 RP-102 Rear panel.

Ground

XLR outRCA in RCA out

Power

XLR in

11RP-102 | Version 1

2. connecting

2. c

on

ne

ctin

g

Fuse


3. operation

The RP-102 has 3 operation modes

1. Normal modeThis is the mode you use when listening to music.

2. Menu modeIn this mode you can alter the settings of the RP-102.

3. Standby modeIn this mode the controls of the RP-102 are deactivated.

Figure 5 RP-102 Front panel.

Operation modes


3. operation

3. o

pe

rati

on

Normal modeIn normal mode there are 3 basic functions/buttons available on the left front.

1. INPUT Selects between the 2 inputs.

2. MENU Switches to “Menu mode”.

3. STANDBY Switches to “Standby mode”.

Menu modeYou enter menu mode, by pushing the ”MENU” button once in Normal mode. In the Menu mode there are 3 basic functions/buttons:

1. Scroll forward in the menu.

2. MENU/ Enter & Exit SELECT submenus and select settings.

3. Scroll backward in the menu.

Figure 6 RP-102 Left front panel.

Functions – left front panel


3. operation

Normal modeIn normal mode there are 3 basic functions/buttons available on the right front:

1. Increase amplification.

2. MUTE Mutes the output.

3. Decrease amplification.

Menu modeIn the text-menu it is possible to change the name of the input. This is done by using the following buttons from the right front:

1. Change selected character.

2. MUTE Go to the next character in the display.


Functions – right front panel

Figure 7 RP-102 Right front panel.


3. operation

3. o

pe

rati

on

You can modify the settings of the RP-102. You do this by entering the menu. The sub-menu items are indicated with a colour.OUTPUT RESET REMOTE, BRIGHT, INPUTS and LOAD In the Examples ( chapter 7 of the manual ) you can find various examples of how to change the settings of the RP-102.

OutputHere you can switch between output 1 and output 2.

ResetRestore the settings of the RP-102 to its default settings.

Remote settingsAn Apple Remote can be purchased with the RP-102. The optional Apple remote can be used on all Reference devices. If you own two (or more) reference devices than it is recommended that you pair the remote(s) with their devices.

InputBy default, the inputs are named input 1 and input 2. In the text-menu you can find a list of predefined input names. If the name of your device is not in the list, than you can make your own device name.You can also disable one of the inputs if it us not used.

LoadIn this menu the load impedance can be adjusted.

Bright In this menu the brightness of the display can be adjusted.

RP-102 Menu: introduction


3. operation

LOADSelect a load impedance. Values between 40Ω and 47kΩ is availible.

Mono MSet the RP-102 to output a mono signal.

SETUPChange the settings of the RP-102.

OUTPUTChange between output 1 and output 2.

DATAShows information about this RP-102.

RESETRestore the settings of the RP-102 to its default settings.

REMOTEChange the settings of the Apple Remote.

REMOTE IDShow the ID of the remote.

UNPAIRUn-pair the remote and the RP-102 by removing the REMOTE ID.

BRIGHTChange the brightness of the display any step between 0 and 3.

INPUTSChange settings for the inputs.

TEXTChoose a name for input X.

RP-102 Menu: discription of the elements


3. operation

RP-102 Menu: tree diagram

MENU

BACK

DATA

INPUT 2

INPUT 1

INPUTS

LEAVE

LOAD

ENA REM

REMOTE ID

REMOTE

* It is possible to manually add a name to the list

TEXT

BACK

GradoDynavectClearaudBenzScheuShelterOrtofonLyraINPUT 1

BACK

*

3. o

pe

rati

on

&

serv

ice

Mono M.

SETUP BACK

OUTPUT OUTPUT 1 / OUTPUT 2

RESET RESET NO / RESET YES

0 / 3BRIGHT

USED USED / NOT USED

40Ω - 47kΩ

MONO OFF / MONO ON


4. operation & service

Safety noticeThe Vitus Audio RP-102 contains no user serviceable parts except from the mains fuse. Do not attempt to open the case. There are potentially dangerous voltages present inside. Should your RP-102 show signs of malfunction, then please contact your dealer or Vitus Audio.

Mains supply voltageAny unit may be set for operation in 100V, 115V or 230V A.C. Units are shipped set for the mains supply voltage according to the destination. The voltage setting can be updated later by your dealer, if necessary.

MaintenanceVitus Audio products are designed to run for many years without the need for regular maintenance. Our products contain no user serviceable parts except from the mains fuse. Should your RP-102 show signs of malfunction, please contact your dealer or Vitus Audio.

Mains fusesThe mains fuses are accessible from the outside of the amplifier. You will find the mains fuses just below the power inlet. If the fuses blow, then you can easily replace them. The fuses only blow on the occurrence of power surges or if there is a fault in the unit. Normally power surges cause no other damage other than blowing the fuses. When the fuses blow repeatedly on replacement, then the unit most likely has a malfunction. In case of malfunction the unit must be returned to Vitus Audio for repair.



Fuse type:230V: 20 x 5mm – 500mA – T - LBC fuse (Time lag fuse)

100-120V: 20 x 5mm – 1 A – T - LBC fuse (Time lag fuse)

Replacing the fuses with fuses of a type and rating different from the original fuses, might result in damage to the unit and injury to you (the user). Damage to the unit as a result of wrongly replacing the mains fuse, will invalidate the warranty.

Replacing a blown fuseREMOVE THE POWER CABLE

In the following steps we will show you how to replace a blown fuse.

5 There is a spare fuse available in the fuse carrier.

spare fuse

blown fuse

2 Take a small flat bladed screwdriver and place it over the fuse carrier.

4 Pull the fuse carrier out.

3 Open the fuse carrier.

1 The fuse carrier is placed on the back of the external power supply under the power connector.

4. o

pe

rati

on

&

serv

ice



7 Push the spare fuse out using a pointy object.

8 Place the spare fuse in the fuse carrier and click the fuse in place.

10 The fuse carrier is in place when you hear “CLICK”.

9 Push the fuse carrier back in place.

6 Take the blown fuse out of the fuse carrier and throw it away.

Replacing a blown fuse continued

21RP-102| Version 1

5. warranty

WarrantyWarranty Statement (modified to fit Vitus Audio)

1. TERMS AND CONDITIONSLIMITED WARRANTYVitus Audio warrants the product designated herein to be free of manufacturing defects in material and workmanship, subject to the conditions hereinafter set forth, for a period of three (3) years from the date of purchase by the original purchaser or no later than five (5) years from the date of shipment to the authorized Vitus Audio cooperating partner, whichever comes first, excepting any cosmetic damage to chassis parts. (See 6)

2. CONDITIONSThis Warranty is subject to the following conditions and limitations. The Warranty is void and inapplicable if the product has been used or handled other than in accordance with the instructions in the owner’s manual, abused, or misused,

damaged by accident or neglect or in being transported, or the defect is due to the product being repaired or tampered with by anyone other than Vitus Audio or authorized Vitus Audio repair center. The product must be packed in its original box and returned to Vitus Audio or an authorized repair center by the customer at his or her sole expense. Vitus Audio will pay return freight of its choice.

IMPORTANT!A returned product MUST be accompanied by a written description of the defect and a photocopy of the original purchase receipt. This receipt must clearly list model and serial number, date of purchase, the name and address of the purchaser and authorized dealer and the price paid by the purchaser. Vitus Audio reserves the right to modify the design of any product without obligation to purchasers of previously manufactured products and to change the prices or specifications of any product

without notice or obligation to any person.

3. REMEDYIn the event the above product fails to meet the above Warranty and the above conditions have been met, the purchaser’s sole remedy under this Limited Warranty shall be to return the product to Vitus Audio or an authorized Vitus Audio repair center where the defect will be rectified without charge for parts and labor, except chassis parts. (See 6)

4. LIMITED TO ORIGINAL PURCHASERThis Warranty is for the sole benefit of the original purchaser of the covered product and shall not be transferred to a subsequent purchaser of the product.

5. DURATION OF WARRANTYThis Warranty expires on the third (3rd) year anniversary of the date of purchase or no later than the fifth (5th) anniversary of the date of shipment to the authorized Vitus Audio cooperating partner, whichever comes first.

5. w

arra

nty


5. warranty

6. CHASSISDamage or cosmetic defects are not warranted.

7. DEMONSTRATION EQUIPMENTEquipment used by an authorized cooperating partner for demonstration purposes is warranted to be free of manufacturing defects in materials and workmanship for a period of three (3) years from the date of shipment to the authorized cooperating partner. After the first year, demo equipment needing warranty service must be packed in its original box and returned to Vitus Audio by the cooperating partner at his or hers sole expense. Vitus Audio will pay return freight of its choice. A returned product must be accompanied by a written description of the defect on a VITUS AUDIO RETURNED GOODS AUTHORIZATION form. Dealer-owned demonstration equipment sold at retail within three (3) years of date from shipment to the dealer is warranted to the first retail customer to be free

of manufacturing defects in materials and workmanship for the duration of the three (3) Year Limited Warranty remaining (as measured from the date of shipment of the equipment to the Vitus Audio partner. In the event warranty service is needed under these conditions, the owner of the equipment must provide a copy of his purchase receipt, fulfilling the requirements described under ”2. Conditions” above. The product must be packed in its original box, and returned to Vitus Audio or an authorized Vitus Audio repair center by the customer at his or her sole expense. Vitus Audio will pay return freight of its choice.

8. MISCELLANEOUSAny implied warranties relating to the above product shall be limited to the duration of this warranty. The warranty does not extend to any incidental or consequential costs or damages to the purchaser. Some countries do not allow limitation on how long an implied warranty lasts or exclusion or limitation of

incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from country to country.

9. WARRANTORInquiries regarding the above Limited Warranty may be sent to the followingaddress:

AVA Group A/SHammershusvej 3HDK7400 HerningDenmarkAtt.: Customer Service


5. warranty

5. w

arra

nty

10. WARRENTY OUTSIDE DANMARKVitus Audio has authorized distribution in many countries in the world. In each country, the authorized importing retailer or distributor has accepted the responsibility for warranty of products sold by that retailer or distributor. Warranty service should normally be obtained from the importing retailer or distributor from whom purchased your product. In the unlikely event of service required beyond the capabilities of the importer, Vitus Audio will fulfill the conditions of the warranty. Such products must be returned at the owner’s expense to the Vitus Audio factory, together with a photocopy of the bill of sale for that product, a detailed description of the problem, and any other information necessary return shipment. In many cases the retailer your purchased the product from, will handle this for you.

11. FURTHER INFORMATION Should you have any further questions related to our warranty – please contact us at the following email: [email protected]


6. specifications

RP-102 Measurements

Front panel: Anodized Aluminium

Body: Powder coated Aluminium

Total weight: ~10 kg

435 mm

425 mm

400 mm

100 mm

90 mm

85 mm

INPUT

MENU SELECT

STANDBY

MUTE

435 mm


6. specifications

6. s

pe

cifi

cati

on

s

RP-102 Specifications

POWER CONSUMPTIONStandby 1 WRMS

Operation 20 WRMS

POWER SUPPLY

Type Linear power supply

Input 230 V / 50 Hz

Output 18V / 1A

DIMENSIONS Hight 100 mm

With 435 mm

Depth 435 mm

Weight ~10 kg

INPUT XLRAnalog

RCAAnalog

Available 1 1

Impedance Switchable 40Ω - 47kΩ

Switchable 40Ω - 47kΩ

Slew rate 35V/ μs 35V/ μs

OUTPUT XLRAnalog

RCAAnalog

Available 1 1

Impedance 75 kΩ 75 kΩ

Frequency response +800kHz +800kHz

Signal to noise ratio < 70dB < 70dB

THD + noise < 0,01% < 0,01%

Gain MM >51dB @ 1KHz

>51dB @ 1KHz

Gain MC >75dB @ 1KHz

>75dB @ 1KHz


6. specifications

Gain values

First choose the amplification (MM/MC) and then set the Load.

You can find amplification and load in the specifications of your pickup cartridge.

The availible gain levels are shown in the lists.

Moving Magnet (MM)

Gain Cartridge Output

51dB 5.5 mV

48dB 8 mV

45dB 11 mV

42dB 15 mV

39dB 22 mV

36dB 30 mV

33dB 45 mV

30dB 60 mV

27dB 90 mV

Moving Coil (MC)

Gain Cartridge Output

75dB 0.4 mV

72dB 0.5 mV

69dB 0.7 mV

66dB 1 mV

63dB 1.5 mV

60dB 2 mV

57dB 3 mV

54dB 4 mV

51dB 5.5 mV


6. specifications

Load values

First choose the amplification (MM/MC) and then set the Load.

You can find amplification and load in the specifications of your pickup cartridge.

Different load values are availible in MM and MC mode as shown in the lists.

Moving Coil (MC)

2 KΩ 400 Ω 130 Ω

1,5 KΩ 380 Ω 110 Ω

1,2 KΩ 360 Ω 60 Ω

1 KΩ 340 Ω 55 Ω

750 Ω 300 Ω 50 Ω

670 Ω 270 Ω 45 Ω

600 Ω 180 Ω 40 Ω

550 Ω 150 Ω

Moving Magnet (MM)

47 KΩ 400 Ω

5,3 KΩ 300 Ω

2,8 KΩ 200 Ω

2 KΩ 150 Ω

1,2 KΩ 120 Ω

1 KΩ 60 Ω

750 Ω 40 Ω

500 Ω

6. s

pe

cifi

cati

on

s


7. examples operating

RP-102 Left front panel.

Example 1 Setting the cartridge load (MM/MC) and load impedanceBy default the RP-102 is set to MM with a load impedance of 40 Ω.

In the example we will change the settings of the RP-102 to match the Cadenza Blue from Ortofon. This is a MC pickup with a load impedance of 50-200 Ω.

The settings for MC and MM are determined by the gain level with 51dB being the changing point. From 27dB to 51dB is MM mode, and from 51dB to 75dB is MC mode.

Start by turning the gain up to above 51dB to go into MC mode. This is done by clicking the top button on the right front panel or clicking up on the MAC remote.

MENU

LEAVELOAD4O Ω45 Ω5O Ω55 Ω

6O Ω

11O ΩSELECT

SELECT

To set the load, start by going to the menu.

Press the“MENU”button to enter Menu Mode.Navigate to the “LOAD” submenu, using the function buttons on the left front.




When in the “LOAD” submenu, you can adjust the load impedance on the left front. Set the load impedance to 110 Ω.

You can adjust the load impedance to 50, 55, 60, 110, 130, 150, or 180 Ω (all withing the range of the pickup cartridge).

Example 2 Changing output from OUTPUT 1 to OUTPUT 2Press the“MENU”button to enter Menu Mode.Navigate to the “OUTPUT” submenu, using the function buttons on the left front.




Enter the OUTPUT submenu.The display now shows Output 1. Press the DOWN button. The display now shows OUTPUT 2. Press the SELECT button and leave the menu. The output is now set to output 2.




MENU

LEAVESETUPBACKOUTPUTOUTPUTOUTPUTOUTPUT

SELECT

SELECT

SELECT

7. e

xam

ple

s

Example 3 Restoring the settings of the RP-102Press the“MENU”button to enter Menu Mode.Navigate to the “RESET” submenu, using the function buttons on the left front




Enter the RESET submenu.The display now shows RESET NO. Press the button. The display now shows RESET YES. Press the SELECT button. The RP-102 automatically goes into standby mode.




MENU

LEAVESETUPBACKOUTPUTDATARESETRESET NORESET YESSTANDBY

SELECT

SELECT

SELECT



Example 4 remotePairing the remote and the RP-102The remote is (fresh from the box) not paired to the RP-102. When you go into the menu to see the remote ID, the display will show NO PAIR. You first have to pair the remote and the RP-102 to get a remote ID. We will show you how to pair the RP-102 and the remote.

Follow these steps

1. Press and hold the Standby button. 2. Press and hold the Next Input button. 3. Hold these buttons down for 5 seconds. The display shows the Remote I.D ( for example 155).

Example 4.1Changing the remote IDWhen two devices have the same remote ID. Then you can change the remote id of one of the devices

Follow these steps

1. Press and hold the standbybutton.

2. Press and hold the Mute button.

3. Hold these buttons down for 5 seconds.

The display now shows the new

remote ID ( old ID + 1, fx 156).

Example 4.2Unpairing the remote and the RP-102

Follow these steps

1. Press and hold the standby button.

2. Press and hold the Previous Input button.

3. Hold these buttons down for 5 seconds. The display shows UNPAIR

Previous Input

MM

Next Input

Mute

Standby

Figure 8 Mac-remote functions.

MC

Select Load Value

(only with RIAA)

7. e

xam

ple

s

Example 4.3Un-pairing of the remote and the RP-102Press the“MENU”button to enter Menu Mode.Navigate to the “REMOTE” submenu, using the function buttons on the left front.




Enter the REMOTE submenu and scroll down using the button. The display now shows “UNPAIR”. Press the “SELECT” button. The display now shows NO PAIR. This means that the remote and the RP-102 are now unpaired. leave the menu.




LEAVESETUPBACKOUTPUTDATARESETREMOTEENA REMUNPAIRUNPAIREDBACK

SELECT

SELECT

SELECT

MENU



Example 5 Changing brightness from 1 to 2By default the brightness is set to 1.

Press the“MENU”button to enter Menu Mode.Navigate to the “BRIGHT” submenu, using the function buttons on the left front.




Enter the “BRIGHT” submenu The display now shows “1”. Press the “” button. The brightness is now set to 2. Press “SELECT” to leave the. “BRIGHT” submenu.The new brightness level is now saved.


LEAVESETUPBACKOUTPUTDATARESETREMOTEBRIGHTBRIGHT 1BRIGHT 2BRIGHT

SELECT

SELECT

SELECT

MENU

7. e

xam

ple

s



Example 6 Changing the name of INPUT 1 to LYRAPress the“MENU”button to enter Menu Mode.Navigate to the TEXT submenu, using the function buttons on the left front.




In the TEXT submenu you will find a list of predefined names, that you can choose from.

Select the name LYRA.The name of INPUT 1 has now been changed from INPUT 1 to LYRA. Leave the TEXT submenu.

When you leave Menu mode the display will show LYRA.

MENU RP-102 Left front panel.

LEAVESETUPBACKOUTPUTDATARESETREMOTEBRIGHTINPUTSBACKINPUTINPUTBACKTEXTINPUTLYRATEXT

SELECT

SELECT

SELECT

SELECT

SELECT



Example 6.1Changing the name of INPUT 1 to VDHULIf you want to use an input-name that is not in the predefined list, then it is possible to manually add a name to the list.

In the text- menu it is possible to change the name of the input. This is done by using the following buttons from the right front:


2. MUTE Go to the next character in the display.


We will now change the input-name “INPUT 1” to VDHUL (Not in the predefined list) .

We continue from the TEXT sub-menu in the previous example.

The display is showing INPUT 1

Press MUTE (The first character in the display starts blinking).

Press or until the first character has the value you want. Press MUTE (The second character in the display starts blinking).

Press MUTE when the last character in the display is blinking. The new device name is now saved, and then you can leave the TEXT sub-menu.

When you are editing the Input name, then you can save the changes at any time. You do this by pressing the SELECT button.

INPUT.NPUTVNPUTP.PUTVDPUTVD.UTVDHUTVDH.TVDHUTVDHU.VDHULVDHUL.VDHULTEXT

MUTE

MUTE

MUTE

MUTE

MUTE

MUTE

MUTE

MENU

RP-102 Right front panel.

7. e

xam

ple

s


7. examples connecting devices

Connecting devices The RP-102 is connected to an RL-102. The RS-101 is powering the speakers.The Media Center is connected to the RCD-101, where the RCD-101 is used as a DAC.

Units

Vitus Audio productsReference Series

RP-102RL-102RS-101RCD-101

3rd. party products

Speakers Media CenterTurntable

RS-101

RP-102

RL-102RCD-101

37

8. p

ictu

res

8. pictures

RP-102 Front

RP-102 | Version 1

Handcrafted in Denmark

v i t u s a u d i o

AVA Group A/S (Vitus Audio), Hammershusvej 3H, DK-7400 Herning, Denmark, Phone: +45 9626 8046

e-mail: [email protected], web site: www.vitusaudio.com

rp-102 - vitus audio · rp-102 | version 1 7 1. getting started 1. getting started figure 1 box...

Documents