roduct specifications · 2020. 12. 15. · side panels are 18 ga powder coated steel reinforced...
TRANSCRIPT
Product Specifications
Model Number: A1XXXXXXX
Hierarchy Compass CabinetsMini H1
OVERVIEWA customizeable storage solution that integrates with accessories that
promote an active learning environment.
SIDE PANEL SPECIFICATIONSSide panels are 18 Ga powder coated steel reinforced with two 20 Ga
25mm square steel tubes. Side panels have option of two rows of 14 peg
holes or fully perforated peg board panles for the mounting of accessories.
BODY SPECIFICATIONSTop panel, rear panel, and bottom panel are all 18 Ga platinum powder
coated steel. There are two 20 Ga hat sections welded to the top panel,
running lengthwise. The bottom panel has one 20 Ga hat section centered
front to back and running lengthwise. Rear panel is also available with a
porcelain steel markerboard adhesive skin applied to exterior.
GLIDE/CASTER SPECIFICATIONSFour 100mm casters are constructed from a reinforced plastic body with
non-marking gray polyurethane wheels. Two casters are locking. Casters
and optional nylon glides have a 0.5” x 1” stem.
DOOR SPECIFICATIONSOptional doors are 18 ga steel with a 20 Ga vertical hat channel. Available
with either a right or left handed door with a locking mechanism that is
secured in the top and bottom panels while locked and features a break-
resistant key. The doors are fully hinged and can be opened 270° to be flat
aginst the side of the cabinet.
SHELF SPECIFICATIONSOptional shelves are 18 Ga steel with a 20 Ga hat section running lengthwise
along the bottom. The 1” thick shelves can be placed at any height.
ENDCAP SPECIFICATIONSEndcaps are cast aluminum. Standard endcaps are held in with four M6 x
12mm screws and create a flush edge around the cabinet top. Mounting
castings are used with our top accessories and are held in with two M6 x
12mm screws. Optional handles are cast aluminum and raise 2.5” off the
top of the cabinet. They are held to the body of the cabinet with four M6 x
12mm screws.
TRAY SPECIFICATIONSCompass uses Gratnell’s trays and the stop-safe runner system to allow
customization within the cabinet. Runners clip into the side panels and
upright assemblies in a virtually unlimited amount of configurations.
Page 1 of 2
SIDE COLOR BODY COLOR
PlatinumBlack Cool Gray Navy Blue Green Yellow Orange Red Purple
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
Page 2 of 2
DIMENSIONS
OPTIONSAvailable with porcelain steel markerboard back panel
Available with perforated side panels (Only in Gray)
Available with casters or glides.
Available with side panels in all nine Hierarchy Colors
Available with or without doors.
Available with preset or custom filling options.
Part Number Filling Dimensions
A1XXXXAXXX Five 3” Trays 14 7/8” W x 25 7/8” H x 19 1/8” D
A1XXXXBXXX One 3”, Two 6” Trays 14 7/8” W x 25 7/8” H x 19 1/8” D
A1XXXXCXXX Three 3”, One 6” Trays 14 7/8” W x 25 7/8” H x 19 1/8” D
A1XXXXDXXX One Full Width Shelf 14 7/8” W x 25 7/8” H x 19 1/8” D
14 7/8"
25 7/8"
19 1/8"
Product Specifications
Model Number: B1XXXXXXXX
Hierarchy Compass CabinetsMini H2
OVERVIEWA customizeable storage solution that integrates with accessories that
promote an active learning environment.
SIDE PANEL SPECIFICATIONSSide panels are 18 Ga powder coated steel reinforced with two 20 Ga
25mm square steel tubes. Side panels have option of two rows of 14 peg
holes or fully perforated peg board panles for the mounting of accessories.
BODY SPECIFICATIONSTop panel, rear panel, and bottom panel are all 18 Ga platinum powder
coated steel. There are two 20 Ga hat sections welded to the top panel,
running lengthwise. The bottom panel has one 20 Ga hat section centered
front to back and running lengthwise. Rear panel is also available with a
porcelain steel markerboard adhesive skin applied to exterior.
GLIDE/CASTER SPECIFICATIONSFour 100mm casters are constructed from a reinforced plastic body with
non-marking gray polyurethane wheels. Two casters are locking. Casters
and optional nylon glides have a 0.5” x 1” stem.
DOOR SPECIFICATIONSOptional doors are 18 ga steel with a 20 Ga vertical hat channel. Available
with either a right or left handed door with a locking mechanism that is
secured in the top and bottom panels while locked and features a break-
resistant key. The doors are fully hinged and can be opened 270° to be flat
aginst the side of the cabinet.
SHELF SPECIFICATIONSOptional shelves are 18 Ga steel with a 20 Ga hat section running lengthwise
along the bottom. The 1” thick shelves can be placed at any height.
ENDCAP SPECIFICATIONSEndcaps are cast aluminum. Standard endcaps are held in with four M6 x
12mm screws and create a flush edge around the cabinet top. Mounting
castings are used with our top accessories and are held in with two M6 x
12mm screws. Optional handles are cast aluminum and raise 2.5” off the
top of the cabinet. They are held to the body of the cabinet with four M6 x
12mm screws.
TRAY SPECIFICATIONSCompass uses Gratnell’s trays and the stop-safe runner system to allow
customization within the cabinet. Runners clip into the side panels and
upright assemblies in a virtually unlimited amount of configurations.
Page 3 of 4
SIDE COLOR BODY COLOR
PlatinumBlack Cool Gray Navy Blue Green Yellow Orange Red Purple
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
Page 4 of 4
DIMENSIONS
OPTIONSAvailable with porcelain steel markerboard back panel
Available with perforated side panels (Only in Gray)
Available with casters or glides.
Available with side panels in all nine Hierarchy Colors
Available with or without doors.
Available with preset or custom filling options.
Part Number Filling Dimensions
B1XXXXAXXX Eight 3” Trays 14 7/8” W x 36 1/8” H x 19 1/8” D
B1XXXXBXXX Four 6” Trays 14 7/8” W x 36 1/8” H x 19 1/8” D
B1XXXXCXXX Four 3”, Two 6” Trays 14 7/8” W x 36 1/8” H x 19 1/8” D
B1XXXXDXXX Two Full Width Shelves 14 7/8” W x 36 1/8” H x 19 1/8” D
B1XXXXFXXX Two 3”, Three 6” Trays 14 7/8” W x 36 1/8” H x 19 1/8” D
B1XXXXGXXX Two 3”, One 6”, One 12” Trays 14 7/8” W x 36 1/8” H x 19 1/8” D
14 7/8"
36 1/8"
19 1/8"
Product Specifications
Model Number: C1XXXXXXXX
Hierarchy Compass CabinetsMini H3
OVERVIEWA customizeable storage solution that integrates with accessories that
promote an active learning environment.
SIDE PANEL SPECIFICATIONSSide panels are 18 Ga powder coated steel reinforced with two 20 Ga
25mm square steel tubes. Side panels have option of two rows of 14 peg
holes or fully perforated peg board panles for the mounting of accessories.
BODY SPECIFICATIONSTop panel, rear panel, and bottom panel are all 18 Ga platinum powder
coated steel. There are two 20 Ga hat sections welded to the top panel,
running lengthwise. The bottom panel has one 20 Ga hat section centered
front to back and running lengthwise. Rear panel is also available with a
porcelain steel markerboard adhesive skin applied to exterior.
GLIDE/CASTER SPECIFICATIONSFour 100mm casters are constructed from a reinforced plastic body with
non-marking gray polyurethane wheels. Two casters are locking. Casters
and optional nylon glides have a 0.5” x 1” stem.
DOOR SPECIFICATIONSOptional doors are 18 ga steel with a 20 Ga vertical hat channel. Available
with either a right or left handed door with a locking mechanism that is
secured in the top and bottom panels while locked and features a break-
resistant key. The doors are fully hinged and can be opened 270° to be flat
aginst the side of the cabinet.
SHELF SPECIFICATIONSOptional shelves are 18 Ga steel with a 20 Ga hat section running lengthwise
along the bottom. The 1” thick shelves can be placed at any height.
ENDCAP SPECIFICATIONSEndcaps are cast aluminum. Standard endcaps are held in with four M6 x
12mm screws and create a flush edge around the cabinet top. Mounting
castings are used with our top accessories and are held in with two M6 x
12mm screws. Optional handles are cast aluminum and raise 2.5” off the
top of the cabinet. They are held to the body of the cabinet with four M6 x
12mm screws.
TRAY SPECIFICATIONSCompass uses Gratnell’s trays and the stop-safe runner system to allow
customization within the cabinet. Runners clip into the side panels and
upright assemblies in a virtually unlimited amount of configurations.
Page 5 of 6
SIDE COLOR BODY COLOR
PlatinumBlack Cool Gray Navy Blue Green Yellow Orange Red Purple
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
Page 6 of 6
DIMENSIONS
OPTIONSAvailable with porcelain steel markerboard back panel
Available with perforated side panels (Only in Gray)
Available with casters or glides.
Available with side panels in all nine Hierarchy Colors
Available with or without doors.
Available with preset or custom filling options.
Part Number Filling Dimensions
C1XXXXAXXX Twelve 3” Trays 14 7/8” W x 51 1/8” H x 19 1/8” D
C1XXXXBXXX Six 6” Trays 14 7/8” W x 51 1/8” H x 19 1/8” D
C1XXXXCXXX Six 3”, Three 6” Trays 14 7/8” W x 51 1/8” H x 19 1/8” D
C1XXXXDXXX Three Full Width Shelves 14 7/8” W x 51 1/8” H x 19 1/8” D
C1XXXXFXXX Three 3”, Three 6”, One 12” Trays 14 7/8” W x 51 1/8” H x 19 1/8” D
C1XXXXGXXX Three 3” , Five 6” Trays 14 7/8” W x 51 1/8” H x 19 1/8” D
C1XXXXHXXX Eight 3”, Two 6” Trays 14 7/8” W x 51 1/8” H x 19 1/8” D
19 1/8" 14 7/8"
51 1/8"
Product Specifications
Model Number: A2XXXXXXXX
Hierarchy Compass CabinetsMidi H1
OVERVIEWA customizeable storage solution that integrates with accessories that
promote an active learning environment.
SIDE PANEL SPECIFICATIONSSide panels are 18 Ga powder coated steel reinforced with two 20 Ga
25mm square steel tubes. Side panels have option of two rows of 14 peg
holes or fully perforated peg board panles for the mounting of accessories.
BODY SPECIFICATIONSTop panel, rear panel, and bottom panel are all 18 Ga platinum powder
coated steel. There are two 20 Ga hat sections welded to the top panel,
running lengthwise. The bottom panel has one 20 Ga hat section centered
front to back and running lengthwise and the rear panel has one 20 Ga
hat sections running vertically. The bottom panel and hat sections in the
top and rear panels have threaded holes to secure the 18 Ga steel upright
assembly. The upright assembly is two C-channels connected by two steel
plates at the top and bottom. The back C-channel and the two steel plates
have slots to be attached to the main body with six M6 x 12mm screws total.
Rear panel is also available with a porcelain steel markerboard adhesive
skin applied to exterior.
GLIDE/CASTER SPECIFICATIONSFour 100mm casters are constructed from a reinforced plastic body with
non-marking gray polyurethane wheels. Two casters are locking. Casters
and optional nylon glides have a 0.5” x 1” stem.
DOOR SPECIFICATIONSOptional doors are 18 ga steel with a 20 Ga vertical hat channel. The right
door has a locking mechanism that is secured in the top and bottom panels
while locked and features a break-resistant key. The doors are fully hinged
and can be opened 270° to be flat aginst the side of the cabinet.
SHELF SPECIFICATIONSOptional shelves are 18 Ga steel with a 20 Ga hat section running lengthwise
along the bottom. The 1” thick shelves can be placed at any height.
ENDCAP SPECIFICATIONSEndcaps are cast aluminum. Standard endcaps are held in with four M6 x
12mm screws and create a flush edge around the cabinet top. Mounting
castings are used with our top accessories and are held in with two M6 x
12mm screws. Optional handles are cast aluminum and raise 2.5” off the
top of the cabinet. They are held to the body of the cabinet with four M6 x
12mm screws.
TRAY SPECIFICATIONSCompass uses Gratnell’s trays and the stop-safe runner system to allow
customization within the cabinet. Runners clip into the side panels and
upright assemblies in a virtually unlimited amount of configurations.
Page 7 of 8
SIDE COLOR BODY COLOR
PlatinumBlack Cool Gray Navy Blue Green Yellow Orange Red Purple
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
Page 8 of 8
Part Number Filling (Per Column) Dimensions
A2XXXXAXXX Five 3” Trays 28 3/8” W x 25 7/8” H x 19 1/8” D
A2XXXXBXXX One 3”, Two 6” Trays 28 3/8” W x 25 7/8” H x 19 1/8” D
A2XXXXCXXX Three 3”, One 6” Trays 28 3/8” W x 25 7/8” H x 19 1/8” D
A2XXXXDXXX One Full Width Shelf 28 3/8” W x 25 7/8” H x 19 1/8” D
DIMENSIONS
OPTIONSAvailable with porcelain steel markerboard back panel
Available with perforated side panels (Only in Gray)
Available with casters or glides.
Available with side panels in all nine Hierarchy Colors
Available with or without doors.
Available with preset or custom filling options.
28 3/8"
25 7/8"
19 1/8"
Product Specifications
Model Number: B2XXXXXXXX
Hierarchy Compass CabinetsMidi H2
OVERVIEWA customizeable storage solution that integrates with accessories that
promote an active learning environment.
SIDE PANEL SPECIFICATIONSSide panels are 18 Ga powder coated steel reinforced with two 20 Ga
25mm square steel tubes. Side panels have option of two rows of 14 peg
holes or fully perforated peg board panles for the mounting of accessories.
BODY SPECIFICATIONSTop panel, rear panel, and bottom panel are all 18 Ga platinum powder
coated steel. There are two 20 Ga hat sections welded to the top panel,
running lengthwise. The bottom panel has one 20 Ga hat section centered
front to back and running lengthwise and the rear panel has one 20 Ga
hat sections running vertically. The bottom panel and hat sections in the
top and rear panels have threaded holes to secure the 18 Ga steel upright
assembly. The upright assembly is two C-channels connected by two steel
plates at the top and bottom. The back C-channel and the two steel plates
have slots to be attached to the main body with six M6 x 12mm screws total.
Rear panel is also available with a porcelain steel markerboard adhesive
skin applied to exterior.
GLIDE/CASTER SPECIFICATIONSFour 100mm casters are constructed from a reinforced plastic body with
non-marking gray polyurethane wheels. Two casters are locking. Casters
and optional nylon glides have a 0.5” x 1” stem.
DOOR SPECIFICATIONSOptional doors are 18 ga steel with a 20 Ga vertical hat channel. The right
door has a locking mechanism that is secured in the top and bottom panels
while locked and features a break-resistant key. The doors are fully hinged
and can be opened 270° to be flat aginst the side of the cabinet.
SHELF SPECIFICATIONSOptional shelves are 18 Ga steel with a 20 Ga hat section running lengthwise
along the bottom. The 1” thick shelves can be placed at any height.
ENDCAP SPECIFICATIONSEndcaps are cast aluminum. Standard endcaps are held in with four M6 x
12mm screws and create a flush edge around the cabinet top. Mounting
castings are used with our top accessories and are held in with two M6 x
12mm screws. Optional handles are cast aluminum and raise 2.5” off the
top of the cabinet. They are held to the body of the cabinet with four M6 x
12mm screws.
TRAY SPECIFICATIONSCompass uses Gratnell’s trays and the stop-safe runner system to allow
customization within the cabinet. Runners clip into the side panels and
upright assemblies in a virtually unlimited amount of configurations.
Page 9 of 10
SIDE COLOR BODY COLOR
PlatinumBlack Cool Gray Navy Blue Green Yellow Orange Red Purple
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
Page 10 of 10
Part Number Filling (Per Column) Dimensions
A2XXXXAXXX Eight 3” Trays 28 3/8” W x 36 1/8” H x 19 1/8” D
A2XXXXBXXX Four 6” Trays 28 3/8” W x 36 1/8” H x 19 1/8” D
A2XXXXCXXX Four 3”, Two 6” Trays 28 3/8” W x 36 1/8” H x 19 1/8” D
A2XXXXDXXX Two Full Width Shelves 28 3/8” W x 36 1/8” H x 19 1/8” D
A2XXXXFXXX Two 3”, Three 6” Trays 28 3/8” W x 36 1/8” H x 19 1/8” D
A2XXXXGXXX Two 3”, One 6”, One 12” Trays 28 3/8” W x 36 1/8” H x 19 1/8” D
DIMENSIONS
OPTIONSAvailable with porcelain steel markerboard back panel
Available with perforated side panels (Only in Gray)
Available with casters or glides.
Available with side panels in all nine Hierarchy Colors
Available with or without doors.
Available with preset or custom filling options.
28 3/8"
36 1/8"
19 1/8"
Product Specifications
Model Number: C2XXXXXXXX
Hierarchy Compass CabinetsMidi H3
OVERVIEWA customizeable storage solution that integrates with accessories that
promote an active learning environment.
SIDE PANEL SPECIFICATIONSSide panels are 18 Ga powder coated steel reinforced with two 20 Ga
25mm square steel tubes. Side panels have option of two rows of 14 peg
holes or fully perforated peg board panles for the mounting of accessories.
BODY SPECIFICATIONSTop panel, rear panel, and bottom panel are all 18 Ga platinum powder
coated steel. There are two 20 Ga hat sections welded to the top panel,
running lengthwise. The bottom panel has one 20 Ga hat section centered
front to back and running lengthwise and the rear panel has one 20 Ga hat
section running vertically. The bottom panel and hat sections in the top and
rear panels have threaded holes to secure the 18 Ga steel upright assembly.
The upright assembly is two C-channels connected by two steel plates at
the top and bottom. The back C-channel and the two steel plates have slots
to be attached to the main body with six M6 x 12mm screws total. Rear
panel is also available with a porcelain steel markerboard adhesive skin
applied to exterior.
GLIDE/CASTER SPECIFICATIONSFour 100mm casters are constructed from a reinforced plastic body with
non-marking gray polyurethane wheels. Two casters are locking. Casters
and optional nylon glides have a 0.5” x 1” stem.
DOOR SPECIFICATIONSOptional doors are 18 ga steel with a 20 Ga vertical hat channel. The right
door has a locking mechanism that is secured in the top and bottom panels
while locked and features a break-resistant key. The doors are fully hinged
and can be opened 270° to be flat aginst the side of the cabinet.
SHELF SPECIFICATIONSOptional shelves are 18 Ga steel with a 20 Ga hat section running lengthwise
along the bottom. The 1” thick shelves can be placed at any height.
ENDCAP SPECIFICATIONSEndcaps are cast aluminum. Standard endcaps are held in with four M6 x
12mm screws and create a flush edge around the cabinet top. Mounting
castings are used with our top accessories and are held in with two M6 x
12mm screws. Optional handles are cast aluminum and raise 2.5” off the
top of the cabinet. They are held to the body of the cabinet with four M6 x
12mm screws.
TRAY SPECIFICATIONSCompass uses Gratnell’s trays and the stop-safe runner system to allow
customization within the cabinet. Runners clip into the side panels and
upright assemblies in a virtually unlimited amount of configurations.
Page 11
SIDE COLOR BODY COLOR
PlatinumBlack Cool Gray Navy Blue Green Yellow Orange Red Purple
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
Page 12 of 12
DIMENSIONS
OPTIONSAvailable with porcelain steel markerboard back panel
Available with perforated side panels (Only in Gray)
Available with casters or glides.
Available with side panels in all nine Hierarchy Colors
Available with or without doors.
Available with preset or custom filling options.
28 3/8"
51 1/8"
19 1/8"
Part Number Filling (Per Column) Dimensions
C2XXXXAXXX Twelve 3” Trays 28 3/8” W x 51 1/8” H x 19 1/8” D
C2XXXXBXXX Six 6” Trays 28 3/8” W x 51 1/8” H x 19 1/8” D
C2XXXXCXXX Six 3”, Three 6” Trays 28 3/8” W x 51 1/8” H x 19 1/8” D
C2XXXXDXXX Three Full Width Shelves 28 3/8” W x 51 1/8” H x 19 1/8” D
C2XXXXFXXX Three 3”, Three 6”, One 12” Trays 28 3/8” W x 51 1/8” H x 19 1/8” D
C2XXXXGXXX Three 3” , Five 6” Trays 28 3/8” W x 51 1/8” H x 19 1/8” D
C2XXXXHXXX Eight 3”, Two 6” Trays 28 3/8” W x 51 1/8” H x 19 1/8” D
Product Specifications
Model Number: A3XXXXXXXX
Hierarchy Compass CabinetsMaxi H1
OVERVIEWA customizeable storage solution that integrates with accessories that
promote an active learning environment.
SIDE PANEL SPECIFICATIONSSide panels are 18 Ga powder coated steel reinforced with two 20 Ga
25mm square steel tubes. Side panels have option of two rows of 14 peg
holes or fully perforated peg board panles for the mounting of accessories.
BODY SPECIFICATIONSTop panel, rear panel, and bottom panel are all 18 Ga platinum powder
coated steel. There are two 20 Ga hat sections welded to the top panel,
running lengthwise. The bottom panel has one 20 Ga hat section centered
front to back and running lengthwise and the rear panel has three 20 Ga
hat sections running vertically. The bottom panel and hat sections in the
top and rear panels have threaded holes to secure the 18 Ga steel upright
assembly. The upright assembly is two C-channels connected by two steel
plates at the top and bottom. The back C-channel and the two steel plates
have slots to be attached to the main body with six M6 x 12mm screws total.
Rear panel is also available with a porcelain steel markerboard adhesive
skin applied to exterior.
GLIDE/CASTER SPECIFICATIONSFour 100mm casters are constructed from a reinforced plastic body with
non-marking gray polyurethane wheels. Two casters are locking. Casters
and optional nylon glides have a 0.5” x 1” stem.
DOOR SPECIFICATIONSOptional doors are 18 ga steel with a 20 Ga vertical hat channel. The right
door has a locking mechanism that is secured in the top and bottom panels
while locked and features a break-resistant key. The doors are fully hinged
and can be opened 270° to be flat aginst the side of the cabinet.
SHELF SPECIFICATIONSOptional shelves are 18 Ga steel with a 20 Ga hat section running lengthwise
along the bottom. The 1” thick shelves can be placed at any height.
ENDCAP SPECIFICATIONSEndcaps are cast aluminum. Standard endcaps are held in with four M6 x
12mm screws and create a flush edge around the cabinet top. Mounting
castings are used with our top accessories and are held in with two M6 x
12mm screws. Optional handles are cast aluminum and raise 2.5” off the
top of the cabinet. They are held to the body of the cabinet with four M6 x
12mm screws.
TRAY SPECIFICATIONSCompass uses Gratnell’s trays and the stop-safe runner system to allow
customization within the cabinet. Runners clip into the side panels and
upright assemblies in a virtually unlimited amount of configurations.
Page 13
SIDE COLOR BODY COLOR
PlatinumBlack Cool Gray Navy Blue Green Yellow Orange Red Purple
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
Page 14 of 14
Part Number Filling (Per Column) Dimensions
A3XXXXAXXX Five 3” Trays 41 7/8” W x 25 7/8” H x 19 1/8” D
A3XXXXBXXX One 3”, Two 6” Trays 41 7/8” W x 25 7/8” H x 19 1/8” D
A3XXXXCXXX Three 3”, One 6” Trays 41 7/8” W x 25 7/8” H x 19 1/8” D
A3XXXXDXXX One Full Width Shelf 41 7/8” W x 25 7/8” H x 19 1/8” D
A3XXXXEXXX Six Cubbies (Total) 41 7/8” W x 25 7/8” H x 19 1/8” D
DIMENSIONS
OPTIONSAvailable with porcelain steel markerboard back panel
Available with perforated side panels (Only in Gray)
Available with casters or glides.
Available with side panels in all nine Hierarchy Colors
Available with or without doors.
Available with preset or custom filling options.
41 7/8"
25 7/8"
19 1/8"
Product Specifications
Model Number: B3XXXXXXXX
Hierarchy Compass CabinetsMaxi H2
OVERVIEWA customizeable storage solution that integrates with accessories that
promote an active learning environment.
SIDE PANEL SPECIFICATIONSSide panels are 18 Ga powder coated steel reinforced with two 20 Ga
25mm square steel tubes. Side panels have option of two rows of 14 peg
holes or fully perforated peg board panles for the mounting of accessories.
BODY SPECIFICATIONSTop panel, rear panel, and bottom panel are all 18 Ga platinum powder
coated steel. There are two 20 Ga hat sections welded to the top panel,
running lengthwise. The bottom panel has one 20 Ga hat section centered
front to back and running lengthwise and the rear panel has three 20 Ga
hat sections running vertically. The bottom panel and hat sections in the
top and rear panels have threaded holes to secure the 18 Ga steel upright
assembly. The upright assembly is two C-channels connected by two steel
plates at the top and bottom. The back C-channel and the two steel plates
have slots to be attached to the main body with six M6 x 12mm screws total.
Rear panel is also available with a porcelain steel markerboard adhesive
skin applied to exterior.
GLIDE/CASTER SPECIFICATIONSFour 100mm casters are constructed from a reinforced plastic body with
non-marking gray polyurethane wheels. Two casters are locking. Casters
and optional nylon glides have a 0.5” x 1” stem.
DOOR SPECIFICATIONSOptional doors are 18 ga steel with a 20 Ga vertical hat channel. The right
door has a locking mechanism that is secured in the top and bottom panels
while locked and features a break-resistant key. The doors are fully hinged
and can be opened 270° to be flat aginst the side of the cabinet.
SHELF SPECIFICATIONSOptional shelves are 18 Ga steel with a 20 Ga hat section running lengthwise
along the bottom. The 1” thick shelves can be placed at any height.
ENDCAP SPECIFICATIONSEndcaps are cast aluminum. Standard endcaps are held in with four M6 x
12mm screws and create a flush edge around the cabinet top. Mounting
castings are used with our top accessories and are held in with two M6 x
12mm screws. Optional handles are cast aluminum and raise 2.5” off the
top of the cabinet. They are held to the body of the cabinet with four M6 x
12mm screws.
TRAY SPECIFICATIONSCompass uses Gratnell’s trays and the stop-safe runner system to allow
customization within the cabinet. Runners clip into the side panels and
upright assemblies in a virtually unlimited amount of configurations.
Page 15
SIDE COLOR BODY COLOR
PlatinumBlack Cool Gray Navy Blue Green Yellow Orange Red Purple
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
Page 16 of 16
Part Number Filling (Per Column) Dimensions
B3XXXXAXXX Eight 3” Trays 41 7/8” W x 36 1/8” H x 19 1/8” D
B3XXXXBXXX Four 6” Trays 41 7/8” W x 36 1/8” H x 19 1/8” D
B3XXXXCXXX Four 3”, Two 6” Trays 41 7/8” W x 36 1/8” H x 19 1/8” D
B3XXXXDXXX Two Full Width Shelves 41 7/8” W x 36 1/8” H x 19 1/8” D
B3XXXXEXXX Nine Cubbies (Total) 41 7/8” W x 36 1/8” H x 19 1/8” D
B3XXXXFXXX Two 3”, Three 6” Trays 41 7/8” W x 36 1/8” H x 19 1/8” D
B3XXXXGXXX Two 3”, One 6”, One 12” Trays 41 7/8” W x 36 1/8” H x 19 1/8” D
DIMENSIONS
OPTIONSAvailable with porcelain steel markerboard back panel
Available with perforated side panels (Only in Gray)
Available with casters or glides.
Available with side panels in all nine Hierarchy Colors
Available with or without doors.
Available with preset or custom filling options.
41 7/8"
36 1/8"
19 1/8"
Product Specifications
Model Number: C3XXXXXXXX
Hierarchy Compass CabinetsMaxi H3
OVERVIEWA customizeable storage solution that integrates with accessories that
promote an active learning environment.
SIDE PANEL SPECIFICATIONSSide panels are 18 Ga powder coated steel reinforced with two 20 Ga
25mm square steel tubes. Side panels have option of two rows of 14 peg
holes or fully perforated peg board panles for the mounting of accessories.
BODY SPECIFICATIONSTop panel, rear panel, and bottom panel are all 18 Ga platinum powder
coated steel. There are two 20 Ga hat sections welded to the top panel,
running lengthwise. The bottom panel has one 20 Ga hat section centered
front to back and running lengthwise and the rear panel has three 20 Ga
hat sections running vertically. The bottom panel and hat sections in the
top and rear panels have threaded holes to secure the 18 Ga steel upright
assembly. The upright assembly is two C-channels connected by two steel
plates at the top and bottom. The back C-channel and the two steel plates
have slots to be attached to the main body with six M6 x 12mm screws total.
Rear panel is also available with a porcelain steel markerboard adhesive
skin applied to exterior.
GLIDE/CASTER SPECIFICATIONSFour 100mm casters are constructed from a reinforced plastic body with
non-marking gray polyurethane wheels. Two casters are locking. Casters
and optional nylon glides have a 0.5” x 1” stem.
DOOR SPECIFICATIONSOptional doors are 18 ga steel with a 20 Ga vertical hat channel. The right
door has a locking mechanism that is secured in the top and bottom panels
while locked and features a break-resistant key. The doors are fully hinged
and can be opened 270° to be flat aginst the side of the cabinet.
SHELF SPECIFICATIONSOptional shelves are 18 Ga steel with a 20 Ga hat section running lengthwise
along the bottom. The 1” thick shelves can be placed at any height.
ENDCAP SPECIFICATIONSEndcaps are cast aluminum. Standard endcaps are held in with four M6 x
12mm screws and create a flush edge around the cabinet top. Mounting
castings are used with our top accessories and are held in with two M6 x
12mm screws. Optional handles are cast aluminum and raise 2.5” off the
top of the cabinet. They are held to the body of the cabinet with four M6 x
12mm screws.
TRAY SPECIFICATIONSCompass uses Gratnell’s trays and the stop-safe runner system to allow
customization within the cabinet. Runners clip into the side panels and
upright assemblies in a virtually unlimited amount of configurations.
Page 17
SIDE COLOR BODY COLOR
PlatinumBlack Cool Gray Navy Blue Green Yellow Orange Red Purple
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
41 7/8"
51 1/8"
19 1/8"
Page 18 of 25
Part Number Filling (Per Column) Dimensions
C3XXXXAXXX Twelve 3” Trays 41 7/8” W x 51 1/8” H x 19 1/8” D
C3XXXXBXXX Six 6” Trays 41 7/8” W x 51 1/8” H x 19 1/8” D
C3XXXXCXXX Six 3”, Three 6” Trays 41 7/8” W x 51 1/8” H x 19 1/8” D
C3XXXXDXXX Three Full Width Shelves 41 7/8” W x 51 1/8” H x 19 1/8” D
C3XXXXEXXX Twelve Cubbies (Total) 41 7/8” W x 51 1/8” H x 19 1/8” D
C3XXXXFXXX Three 3”, Three 6”, One 12” Trays 41 7/8” W x 51 1/8” H x 19 1/8” D
C3XXXXGXXX Three 3” , Five 6” Trays 41 7/8” W x 51 1/8” H x 19 1/8” D
C3XXXXHXXX Eight 3”, Two 6” Trays 41 7/8” W x 51 1/8” H x 19 1/8” D
DIMENSIONS
OPTIONSAvailable with porcelain steel markerboard back panel
Available with perforated side panels (Only in Gray)
Available with casters or glides.
Available with side panels in all nine Hierarchy Colors
Available with or without doors.
Available with preset or custom filling options.
Product Specifications
Model Number: D3XXXXXXXX
Hierarchy Compass CabinetsGrande
OVERVIEWA customizeable storage solution that integrates with accessories that
promote an active learning environment.
SIDE PANEL SPECIFICATIONSSide panels are 18 Ga powder coated steel reinforced with two 20 Ga
25mm square steel tubes. Side panels have option of three rows of 14 peg
holes or fully perforated peg board panles for the mounting of accessories.
BODY SPECIFICATIONSTop panel, rear panel, and bottom panel are all 18 Ga platinum powder
coated steel. There are two 20 Ga hat sections welded to the top panel,
running lengthwise. The bottom panel has one 20 Ga hat section centered
front to back and running lengthwise and the rear panel has three 20 Ga
hat sections running vertically. The bottom panel and hat sections in the
top and rear panels have threaded holes to secure the 18 Ga steel upright
assembly. The upright assembly is two C-channels connected by two steel
plates at the top and bottom. The back C-channel and the two steel plates
have slots to be attached to the main body with six M6 x 12mm screws total.
Rear panel has four sets of peg holes for hangers and is also available with
a porcelain steel markerboard adhesive skin applied to exterior.
GLIDE/CASTER SPECIFICATIONSFour 100mm casters are constructed from a reinforced plastic body with
non-marking gray polyurethane wheels. Two casters are locking. Casters
and optional nylon glides have a 0.5” x 1” stem.
DOOR SPECIFICATIONSOptional doors are 18 ga steel with a 20 Ga vertical hat channel. The right
door has a locking mechanism that is secured in the top and bottom panels
while locked and features a break-resistant key. The doors are fully hinged
and can be opened 270° to be flat aginst the side of the cabinet.
SHELF/DIVIDER SPECIFICATIONSShelves are 18 Ga steel with a 20 Ga hat section running lengthwise along
the bottom. The 1” thick shelves can be placed at any height. 18 Ga vertical
divider is 1 1/4” thick with slot cut for shelf.
ENDCAP SPECIFICATIONSEndcaps are cast aluminum. Standard endcaps are held in with four M6 x
12mm screws and create a flush edge around the cabinet top. Mounting
castings are used with our top accessories and are held in with two M6 x
12mm screws. Optional handles are cast aluminum and raise 2.5” off the
top of the cabinet. They are held to the body of the cabinet with four M6 x
12mm screws.
LAPBOARD HANGERSEight hangers are included with each Grande cabinet. Hangers may be
installed through cabinet peg holes (2 each side, 4 back) using M6 x
12mm screws and nuts provided. Lapboards sold separately.
Page 19
SIDE COLOR BODY COLOR
PlatinumBlack Cool Gray Navy Blue Green Yellow Orange Red Purple
41 7/8"
60 5/8"
54.4"
29.8"
3"
19 1/8"
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
Page 20 of 25
41 7/8"
60 5/8"
54.4"
29.8"
3"
19 1/8" 41 7/8"
60 5/8"
54.4"
29.8"
3"
19 1/8"
41 7/8"
60 5/8"
54.4"
29.8"
3"
19 1/8"
41 7/8"
60 5/8"
54.4"
29.8"
3"
19 1/8"
OPTIONSAvailable with porcelain steel markerboard back panel
Available with perforated side panels (Only in Gray)
Available with casters or glides.
Available with side panels in all nine Hierarchy Colors
Available with or without doors.
Available with preset or custom filling options.
Part Number Filling Dimensions
D3XXXXEXXX Four Cubbies 41 7/8” W x 60 5/8” H x 19 1/8” D
DIMENSIONS
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
29"
42"
54.25"
20"
24" 36"
20"
48"
20"
Page 21 of 25
Hierarchy Compass CabinetsTransaction Top Dimensions
MINI TOP MAXI TOPMIDI TOP
- Laminate tops are 1 1/8” thick particle board core with HPL and 3mm T-mold Edge
- Butcher tops are 1 1/2” thick, solid Maple (adds 0.375” to above heights)
H1
H3
H2
TRANSACTION TOP DIMENSIONS
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
Page 22 of 25
Hierarchy Compass CabinetsLectern Top Dimensions
MINI H2 MIDI H2
**All Lectern Tops are 22” deep**
24.0" 36.0" 22.0"
10
24.0" 36.0" 22.0"
10
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
Page 23 of 25
Hierarchy Compass CabinetsShelf Dimensions
MINI SHELF MAXI SHELFMIDI SHELF
**All shelves are 1” thick and height adjustable in 1/2” increments**
17.6"
8.3"
28.0"
8.5"
43.0"
9.9"
16.5" 26.7"
25.9"
16.5" 40.4"
39.5"
13.1" 16.5"
12.3"
H1
H3
H2
17.6"
8.3"
28.0"
8.5"
43.0"
9.9"
16.5" 26.7"
25.9"
16.5" 40.4"
39.5"
13.1" 16.5"
12.3"
INTERNAL DIMENSIONS
**Assumes equal spacing of shelves**
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
Page 24 of 25
10.0" 12.5"
19.25"
25.5"
12.5"
8.25"
12.5" 8.5"
10.0" 12.5"
19.25"
25.5"
12.5"
8.25"
12.5" 8.5"
10.0" 12.5"
19.25"
25.5"
12.5"
8.25"
12.5" 8.5"
10.0" 12.5"
19.25"
25.5"
12.5"
8.25"
12.5" 8.5"
Hierarchy Compass CabinetsCubby Dimensions
MAXI H1 MAXI H2
MAXI H3 GRANDE
**All cabinet cubbies are 18” deep**
MooreCo | Vanerum North America 2885 Lorraine Avenue | Temple, TX 76501p: 800.749.2258 | f: 866.888.7483www.moorecoinc.com | www.vanerumnorthamerica.com Rev 08/05/20 RMC
Page 25 of 25
Hierarchy Compass CabinetsOgee Board Dimensions
MIDI H1 MAXI H2
**All ogee mounts add 35” to overall height**
58.9"
28.1"
26.9"
40.5"
41.7"
71.1"
35"
19.2"
58.9"
28.1"
26.9"
40.5"
41.7"
71.1"
35"
19.2"
58.9"
28.1"
26.9"
40.5"
41.7"
71.1"
35"
19.2"