rnc basic commands (2)
DESCRIPTION
rnc commandTRANSCRIPT
-
RNC DOCUMENT (Prepared by Sandeep)
MSS POOLING,
--HOW TO CHECK THE MSS is in POLLING FROM NSS END?
A) ZE3I:TYPE=PAR;
found mss name and NRI VALUES under pooling.
SAME VALUES MUST BE IN IUCS RNW OBJECT BROWSER IF IUCS IN POOLING.
--HOW TO CHECK THE CALL STATUS FOR PARTICAULAR WBTS
--NOTE DOWN THE ICSU FOR PARTICULAR WBTS
ENTER INTO SERVICE TERMINAL USING
ZDDS:ICSU,(NO);
CREATE BRM MONITORING
ZLP:1,E2K
MCD:(WBTS-ID),6;---FOR WHOLE WBTS
MCD:(WBTS-ID),6,0,(WCELL-ID),0;----FOR PARTICAULAR WCELL.
--HOW TO DISABLE and Enable IPNB by MML.
ZDDS;
CREATE RNW MISC UTILITIES
ZLE:1,RUOSTEQX
1
IR:WBTS_ID;---
--HOW TO MOVE THE SITE FROM ONE ICSU TO ANOTHER ICSU
IR:WBTS_ID,IUB_ID,IUB_TYPE:ICSU_ID
EX:IR:746,900,I:6------(6 Means new icsu id)
-
RNC DOCUMENT (Prepared by Sandeep)
--how to check what are the sites are connected to particular icsu
ZDDS;
CREATE RNW MISC UTILITIES
ZLE:1,RUOSTEQX
1
I:icsu-no;
--how to check wbts status ?
SA:(WBTS-NO)----FOR PARTICULAR WBTA STATUS.
SB: -------------BLOCKED WCELLS FOR THE WHOLE RNC
how to remove/add the tag under faulty unit.
ZDDS;
CREATE RECOVERY Debugger.
ZLP:1,RCB;
1
TPP:DMCU,FULL,C,(FAULTY-TAG);
TPP:OMU,1,C,(FAULTY TAG);
HOW TO POWER SHUTDOWN/FEED for Particular unit.
ZLP:1,HME
1
DG:(rack,subrack,ppa);
EX- --0000-HME>DG:1,1,2---(SFU-0) For more information check ZWFI:PS;
-
RNC DOCUMENT (Prepared by Sandeep)
How to get the temperature for Particular unit.
ZLP:1,HME
1
DG:(rack,subrack,ppa);
EX- --0000-HME>DI:1,1,2---(SFU-0 TEMPERAURE)
HOW TO get the Hardware information for particular unit
ZWFL:P;
how to get control plane for wbts
ZDDS:RSMU,0---(WORKING RSMU)
CREATE SAAL & AAL2SIG UTIL
ZLP:1,SLL;
1
002E-SLL>I:SCTP,ICSU-0;(UNDER ICSU -0)
How to Troubleshoot the IUCS/IUPS
Parameters for the Ethernet interface
Example command: Read the bandwidth of IFGE0 interface on the NPGE 0 unit to 1000.
ZQAI:NPGE,0;
The total capacity of the NPGE interface card is 1.65 Gbps and this capacity is shared between the two
interfaces.
Interrogate IP addresses e.g. in the NPGE units is done using MML command is ZQRI. The IU-PS user plane address 10.131.0.62/32 in NPGEP 0 in the example
ZQRI:NPGEP,0;
O/P
VL102 10.131.0.62/32.
-
RNC DOCUMENT (Prepared by Sandeep)
Interrogating VLANs
You can interrogate a VLAN interface with commands QRE. NPGE(P) is the only unit to support VLAN
interface. VLAN can be created using command
ZQRE:NPGEP,0;
Interrogating IP forwarding for ICSU and NPGE
ZQRH:NPGE,0:;
Interrogate a static route for the NPGE to the gateway
Control plane is terminated to PAPU unit in SGSN. Static route is defining the route to SGSN through the
gateway.
Interrogate is done using ZQKB command. If the network address for the PAPU in the SGSN is
10.10.6.192/26 and the gateway IP address is 10.1.2.7 in the multilayer switch at the RNC site, the static
route is configured using MML command(ZQKC:NPGE,2:10.10.6.192,26:10.1.2.7;)
ZQKB:NPGEP,0;
Interrogate source IP addresses and Destination IP addresses for SCTP
ZOYI::A;
Interrogate source IP addresses for ICSUS
ZOYL;
Interrogating Parameter SET Data.
ZOYO;
Modifying association state
ZOYS:M3UA:IUPS,0:ACT:;
-
RNC DOCUMENT (Prepared by Sandeep)
Interrogating Signaling link set data
ZNSI:NA1
Interrogating Signaling Point Data.
ZNRI:NA1;
Allow activation of signalling link and signalling route
ZNLA:1:;
Allow activation of signalling route with NVA command
ZNVA:NA1,2001:,:;
Change signalling link and signalling route state
ZNLC:1,ACT:;
ZNVC:NA1,2001:,:ACT:;
Interrogating SCCP for signaling point
ZNFI:NA1;
Interrogating subsystems to signalling point
ZNFJ:NA1;
Interrogating states for SCCP and subsystem
ZNGI:NA1;
-
RNC DOCUMENT (Prepared by Sandeep)
Interrogating subsystem states using command
ZNHI:NA1;
Interrogating broadcast status of SCCP signalling poinT
ZOBI:NA1;