richter valves and pumps - spartan controls/media/resources/richter/ca/70... · richter is a...
TRANSCRIPT
PFA-lined
Corrosive and high-purity fluids
-60 to +200 °C (-75 to 400 °F)
DIN EN 14432 (ADR/RID 2011): ball valves
Richter Valves and Pumpsfor dangerous goods carriage and containers– road, rail, ship –
Dan
ger
ous
Go
od
s
Dangerous Goods
2
Richter valves and pumps for dangerous goods carriage and containersRichter is a specialist for the shut-off, control, pressure-safeguarding and pumping of highly corrosive and high- purity fluids in a wide range of applications, even if these are toxic, combustible or hazardous to the environment: valves from DN 15-1000 (1/2” to 40”) and pumps from 0.1 to 600 m3/h (0.4 to 2600 USgpm), in each case for temperaturesfrom-60to+200°C(-75to400°F).
The standard DIN EN 14432 “Tanks for the carriage of dangerous goods – equipment for tanks for the carriage of liquid chemical products – product shut-off and gas exchange valves” has been in force since January 2011.
The ball valves KN/F and KK/F with a PFA lining type-approved to DIN EN 14432 (ADR/RID 2011) are ideally suited for use on road tankers, tank wagons and transport containers. They comply with the German Clean Air Act (“TA Luft”)
Richter products are in use on road, rail and water as • PFA-linedballvalvesofflangeandwafer-typedesign
on tank wagons, road tankers and on dangerous goods containers
• PFA/PTFE-linedbutterflyvalvesonacidtankships• PFA-lineddiaphragmvalvesasfillinganddrain
valves on special bromine containers • PFA-linedmagneticdrivepumpsonroadtankers
for faster unloading, e.g. for acids
Stationary applications However, Richter is the first choice for stationary appli-cations, too, e.g. with self-priming centrifugal pumps for the pulsation-free overhead draining of containers, with bottom valves for self-draining and with safety relief valves to avoid excessive pressures in vessels and systems.
Ball valve KN (ISO/DIN) and KNA (ASME/ANSI)Type-approved to DIN EN 14432 (ADR/RID 2011)
• 3.5mmthickliningmadeofpurePFA, optionally 5 mm (from DN 25/1”)
• Gas-tightintheseat,DINEN12266leakagerateA• Self-adjustingENVIPACKstemsealing,virtually
maintenance-free• Labyrinth-typebodysealing• Variousballversions,blowout-proof• BodyofductilecastironEN-JS1049/ASTMA395• DN15-200and1/2”-8”, full bore (apart from
DN 200 and 8”)• -60to+200°C(-75to400°F),max.16bar(235psi)
For more detailed product information, see brochure KN/KNA/... No. 142
Overview of Richter valves and pumps for the carriage of dangerous goodsDesign Lining Type-approved/ Conforms Sizes, Function Mounted Face to face Certified to German flow range onboard on and flanges Clean Air Act truck/wagon/ ship/container
Ball valve KN, KNA, BVA PFA DIN EN 14432 (KN, KNA),
yes DN 15-200/
Shut-off valve yes ISO/DIN,
AAR Am. Rail (KNA, BVA) 1/2”-8” ASME/ANSI
Compact ball valve KK PFA no yes DN 25-150/1”-6” Shut-off valve yes Flangeless
Butterfly valves NK PFA/PTFE no yes DN 50-400/
Shut-off valve yes ISO/DIN,
2”-16” API, MSS
Diaphragm valve MV PFA no yes DN 15-150/
Shut-off valve yes ISO/DIN,
1/2”-6” ASME/ANSI
Drain valve KA-N PFA AAR American Rail yes DN 25-200/1”-4” Shut-off valve yes ASME/ANSI
Magnetic drive pumps PFA no yes 0.2 to 150 m3/h
Container yes
ISO/DIN, MNK, RMA, RMI draining ASME/ANSI
Advantages of the PFA/PTFE fluoroplastic lining:• Universalcorrosionresistance:muchbetterthan
e.g. Duplex, Hastelloy®, PVDF, ETFE and even than titanium and nickel
• Antiadhesivevacuumresistantlining,easyCIP• Alsoforhigh-purityandsolids-ladenfluids• Largetemperaturerangeto200°C(400°F)• Muchshorterleadtimeandmuchlowerpricedthan
specialty metal valves and pumps
3
Ball valve KKType-approved to DIN EN 14432 (ADR/RID 2011)
• 3.5mmthickliningmadeofpurePFA• FullborewithDN25to50(1”to2”),reducedbore
with DN ≥ 65 (≥ 2½”)• Gas-tightintheseat,DINEN12266leakagerateA• Self-adjustingstemsealing,virtuallymaintenance-free• Flangelesscompactdesign• PFAballwithseparatestem,optionallyAl2O3,
blowout-proof • BodyofductilecastironEN-JS1049/ASTMA395• DN25to150(1”to6”)• -60to+180°C(-75to360°F),max.16bar(235psi)
For more detailed product information, see brochure KN/KNA/.../KK No. 142
Diaphragm valve MV, MVM• 3-3.5mmthickliningmadeofpurePFA• Hermeticallytight• Safetystuffingboxoptional• 2-plyPTFE/EPDMdiaphragm• Adjustabletravelstopandfloatingtubenutprotect
diaphragm against excessive closing force • BodyofductilecastironEN-JS1049/ASTMA395• DN15to150(1/2” to 6”)• -60to+150°C(-75to300°F),max.16bar(235psi)
For more detailed product information, see brochure MV, MVM No. 411
Shut-off butterfly valve NKS, NKL• 3.5mmthickbodyliningmadeofpurePTFE• Gas-tightintheseat,DINEN12266leakagerateA• Disc/stemunitPFA-linedorstainlesssteel,alloyC,
titanium • Self-adjustingstemsealing,virtuallymaintenance-free• Optionallywithsafetystuffingbox• BodyofductilecastironEN-JS1049/ASTMA395• DN50to400(2”to16”),waferandlug-styledesigns• -60to+200°C(-75to400°F),max.10bar(145psi)
For more detailed product information, see brochure NK/NKS/NKL No. 139
For ASME/ANSI standard regions Richter offers “AAR Association of American Railroad” certified PFA-lined valves for operating pressures to 18 bar (260 psi) and temperatures to 200 °C (400 °F):
• Shut-offballvalvesBVAandKNAto6”and• bottomdrainballvalvesKA-Nto4”.
These series are of similar design like series KN/KNA shown on page 2:
• 3.5mmthickliningmadeofpurePFA• Gas-tightintheseat,labyrinth-typebodysealing• Self-adjustingstemsealing• Sizes1/2” to 6”, full and reduced bore• -60to200°C(-75to400°F),max.
For more detailed product information, see brochure BVA/BVI No. 938 and KN/KNA/.../KA-N No. 142
Presented by:
Richter Chemie- Technik GmbHOtto-Schott-Str. 2, D-47906 Kempen, GermanyTel. +49(0) 21 52/146-0, Fax +49(0) 21 52/146-190www.richter-ct.com, [email protected] P
ublic
atio
n N
o. 7
14en
06.
12 ©
Ric
hter
Che
mie
-Tec
hnik
Gm
bH. S
ubje
ct to
cha
nge
with
out n
otic
e. P
rinte
d in
Ger
man
y. R
icht
er a
nd S
AFE
GLI
DE
® =
TM
of
Ric
hter
Che
mie
-Tec
hnik
Gm
bH, I
DE
X =
TM
of I
DE
X C
orpo
ratio
n, H
aste
lloy®
= T
M H
ayne
s
4
Dangerous Goods
Richter pumps for dangerous goods road tankersMagnetic drive pumps RMI, RMASealless magnetic drive centrifugal pumps with fluoroplastic lining. Dimensions and nominal ratings to ISO/EN 22858/ISO 2858 and ASME/ANSI B73.3.
Richter pumps RMI/RMA are used when stainless steel and conventional plastics are not sufficiently corrosion-resistant. They are more corrosion-resistant, considerably better priced and more quickly available than pumps made of special metals (e.g. Hastelloy®, titanium, nickel).
• Eddy-current-free,nointroductionofheatinto the fluid
• Hermeticallytight,norotaryshaftseal,thus minimum maintenance need
• Thick-walledliningmadeofpurePFA• Sturdy,completelymetalsupported• Hydraulicallyoptimised,closedimpeller• CompliantwithATEXandGermanCleanAirAct
(“TA Luft”)• Plainbearingsmadeofhigh-quality,pureSSiC• Dry-runoptimisedSAFEGLIDE® PLUS optional• DoublecansystemCFRP/PTFE,metal-free• PermanentmagnetsNdFeB/SmCo• 0.2to150m³/h(1to650USgpm)at2900rpm• -30to+150°C(-20to300°F),max.20bar(290psi)
For more detailed product information, see brochure RMI/RMA No. 683
(m3/h)
(ft)
60
40
20
0
(m)
240
160
80
0
(USgpm)200 300 400 5001000
(USgpm)100 150 200 250500
40 60 80 100 120200
(m3/h)20 30 40 50 60100
Flow rate – 2900 rpm (50 Hz)
Flow rate – 1450 rpm (50 Hz)
Del
iver
y he
ad –
290
0 rp
m (5
0 H
z)
(ft)
15
10
5
0
(m)
60
40
20
0
Del
iver
y he
ad –
145
0 rp
m (5
0 H
z)
50-32-200
65-40-20080-50-200
80-50-160
40-25-160
50-32-160
40-25-125
50-32-125
(m3/h)
(ft)
60
80
100
40
20
0
15
20
25
10
5
0
(m)
320
240
160
80
0
(ft)
80
60
40
20
0
(USgpm)200 300 400 500 6001000
40 60 80 100 120 140200
Flow rate – 3500 rpm (60 Hz)
(m3/h)
(USgpm)100 150 200 250 300500
20 30 40 50 60 70100
Flow rate – 1750 rpm (60 Hz)
Del
iver
y he
ad –
350
0 rp
m (6
0 H
z)
(m)
Del
iver
y he
ad –
175
0 rp
m (6
0 H
z)
65-40-200
50-32-200
80-50-200
80-50-160
40-25-160
40-25-125
50-32-16050-32-125
ISO/DIN Sizes and flow rates, 50 Hz
5
(m3/h)
(ft)
60
80
100
40
20
0
15
20
25
10
0
(m)
320
240
160
80
0
(ft)
80
60
40
20
0
(USgpm)200 300 400 500 6001000
40 60 80 100 120 140200
Flow rate – 2900 rpm (50 Hz)
(m3/h)
(USgpm)100 150 200 250 300500
20 30 40 50 60 70100
Flow rate – 1450 rpm (50 Hz)
Del
iver
y he
ad –
290
0 rp
m (5
0 H
z)
(m)
Del
iver
y he
ad –
145
0 rp
m (5
0 H
z)
3 x 1.5 x 8“
3 x 2 x 10“
4 x 3 x 8“3 x 2 x 8“1.5 x 1 x 8“
1.5 x 1 x 6“
3 x 1.5 x 6“
(m3/h)
(ft)
80
60
120
140
100
160
40
20
0
(m)
480
400
320
240
160
80
0
(ft)
20
15
30
35
25
40
10
5
0
(m)
120
100
80
60
40
20
0
(USgpm)200 300 400 500 600 700 8001000
40 60 80 100 120 140 160 180200
(m3/h)
(USgpm)100 150 200 250 300 350 400500
20 30 40 50 60 70 80 90100
Flow rate – 3500 rpm (60 Hz)
Flow rate – 1750 rpm (60 Hz)
Del
iver
y he
ad –
350
0 rp
m (6
0 H
z)
Del
iver
y he
ad –
175
0 rp
m (6
0 H
z)
3 x 1.5 x 8“
3 x 2 x 10“
3 x 1.5 x 6“
3 x 2 x 8“
3 x 2 x 6“
1.5 x 1 x 6“
1.5 x 1 x 8“4 x 3 x 8“
3 x 2 x 6“
ASME/ANSI Sizes and flow rates, 60 Hz