revolver magnetic separator by - zealtek · 2015-09-30 · revolver magnetic separator kentucky...
TRANSCRIPT
R E V O LV E R MA G N E T I C S E PA R ATO R
K e n t u c k y O f f i c e
7 7 5 O l d P r e s t o n H w y S .
S h e p h e r d s v i l l e , K Y 4 0 1 6 5
( 5 0 2 ) 3 7 6 - 6 4 4 2
b y :
F O R M O R E I N F O R M A T I O N C O N T A C T U S A T :
N o r t h C a r o l i n a O f f i c e
1 0 8 J o n q u i l C o u r t
M o o r e s v i l l e , N C 2 8 1 1 7
( 7 0 4 ) 4 0 2 - 6 1 9 3 M
M i c h i g a n O f f i c e
2 9 4 4 5 B e c k R o a d
W i x o m , M I 4 8 3 9 3
( 2 4 8 ) 6 1 3 - 3 5 6 3
R E V O L V E R M A G N E T I C S E P A R A T O R S P E C I F I C A T I O N S
Model No. Total No.
Bars
Equipment Nom. Dimensions (inches) Max Flowrate Total Area Betw. Bars
(ft2)
Flow Velocity (in/sec) A B C D E O.A.H. GPM ft
3/sec
RVV-105 105 19.875 54.5 58.125 6 8 59 1/2 300 0.67 4.01 2.00
RVV-120 120 32.375 54.5 58.125 6 8 72 425 0.95 6.23 1.82
RVV-150 150 57.375 54.5 58.125 8 10 97 675 1.50 8.76 2.06
RVV-180 180 82.375 54.5 58.125 8 10 122 900 2.01 11.93 2.02
RVV-210 210 107.375 54.5 58.125 12 14 147 1150 2.56 15.09 2.04
RVV-240 240 132.375 54.5 58.125 12 14 172 1375 3.06 18.26 2.01
E x a c t r a t i o n ’ s R e v o l v e r S e r i e s M a g n e t i c S e p a r a t o r p r o d u c t s
r a i s e t h e c a l i b e r o f o p e r a t i o n f o r s e p a r a t i o n a n d r e m o v a l
o f f e r r o u s m e t a l s f r o m l i q u i d s .
The Revolver is a Variation of the High Standard
High Strength Permanent Magnets Encapsulated in a Stainless Steel Tube
Low Fluid Velocity Typically Less Than 2 in/sec (50 mm/sec) Between Bars
The Standard Magnetic Bars and Chain are Routed Out Over the Edge of
the Tank to Discharge into a Hopper
The Exactration Revolving Cleaning Mechanism Wipes the Bars as They are
Positioned Over the Hopper
Chain Driven Wipers are Less Complex than the Gear and Cam Design of
the Standard Wiper
R E V O L V E R C R I T I C A L D E S I G N F E A T U R E S
W W W . E X A C T R A T I O N . C O M ( 8 4 4 ) 4 4 - E X A C T
These units incorporate magnetic bar technology excellent for removal of magnetic and paramagnetic particles.
Our patent pending automation technology eliminates the mechanical drive wiper system and replaces it with a
revolving wiper system for cleaning of the magnetic bars.
Reduce or Eliminate Disposable Media
Built as a Drop In Module
The Cleaning Section is Outside the Tank
Less Complicated Cleaning Mechanism
Requires Less Space Because it Does Not Have the Large Wiper Assembly
R E V O L V E R A D V A N T A G E S
B R O C H U R E I S S U E 0 1
R E V O L V E R H O W I T W O R K S !
Cold Rolling Coolant Systems
Coil/Strip Cleaning Systems
Coil Grinding Systems
Polishing Filter for Existing Ferrous Coolant Systems
R E V O L V E R A P P L I C A T I O N S
Dirty liquid enters the separator tank at the bottom through a distributor pipe and flows evenly between
the magnetic bars. Perforated distribution panels located behind the magnetic bars insure that the
liquid flows at a uniform velocity throughout the entire magnetic field thus improving the efficiency of
separation. Fluid velocity is held below 2 in/sec (50 mm/sec) providing sufficient time for the ferrous
particles to attract to the magnetic bars. Typically, each bar will coat with 1/8” to 3/16” thick build up of
ferrous particles (swarf), depending upon the dirt generated by the process. The bars are continuously
indexed through the separation tank, then routed out over the edge of the tank to the cleaning section.
Each bar is wiped three (3) times by the upper and lower revolving wiper plates, which discharge the
material directly into a hopper. The clean liquid flows out of the tank at the top through a collector pipe
and into the clean tank.