reset printer
DESCRIPTION
oprinterTRANSCRIPT
Reset Segala Macam Printer
1. Printer Canon
Canon GENERIC “S” SERIES RESET CODE
Waste Ink Counter Reset.(1) matiin printer.(2) pencet & tahan tombol RESUME, lalu pencet & tahan tombol POWER.(3) lepasin tombol RESUME, lalu pencet and lepasin tombol RESUME dua (2) kali insuccession. Note: you are still tahan the POWER tombol). The printer’s carriage will “reset”or move momentarily. If the above was properly performed the printer will enter the“Service Mode”.(4) Pencet the RESUME tombol 4 times, this will select the clear waste ink counter function. The lampwill alternate (change) color with each key pencet.1. Service/Factory test printout, including ink sensor check.2. EEPROM – Info printout.3. EEPROM – Initialization.4. Reset the Waste ink counter.5. Printer model setting. (More selections beyond this point – However it is best leave them unaltered – You have been warned!)After selecting the desired mode (eg 4), pencet the POWER tombol to “set” the change, and return to the top of the function selection menu. Pencet the POWER tombol again to restart the printer.
--------------------------------------------------------------------------------------------------
Canon PIXMA iP1000Waste Ink Counter Reset Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.2. Pencet and tahan the POWER tombol, turn on the printer.3. The indicator (L.E.D.) should be green.4. Pencet and lepasin the RESUME tombol , the indicator (L.E.D.) should be orange.5. Pencet and lepasin the RESUME tombol lagi, the indicator (L.E.D.) should be green.6. Lepasin kedua tombols.
--------------------------------------------------------------------------------------------------
Canon PIXMA iP1500Waste Ink Counter Reset. Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.2. Pencet and tahan the POWER tombol, turn on the printer.3. The indicator (L.E.D.) should be green.4. Pencet and lepasin the RESUME tombol , the indicator (L.E.D.)should be orange.5. Pencet and lepasin the RESUME tombol again, the indicator(L.E.D.) should be green6. Lepasin both tombols
--------------------------------------------------------------------------------------------------
Canon i320, i255Waste Ink Counter Reset.
Step 1 : Manual Temporary1. Unplug power and USB.2. Open door and tahan power tombol.
3. Connect power.4. Close door, then lepasin power tombol.or Step 1: Manual Temporary1. Turn off the printer. And disconnect the printer cable.2. Pencet and tahan the POWER tombol, turn on the printer.3. The indicator (L.E.D.) should be green.4. Pencet and lepasin the RESUME tombol , the indicator (L.E.D.) should be orange.5. Pencet and lepasin the RESUME tombol again, the indicator (L.E.D.) should be green.6. Lepasin both tombols.step 2 : Software for Permanant1. Reconnect the printer cable.2.Open General Tools software and select (USB PORT)3 .Choose (SET DESTINATION 1) And it should be reset.Remark “After service mode Pls use software for permanent reset”
--------------------------------------------------------------------------------------------------
Canon i850, i950, S600Start with the printer OFF
1. Tahan down RESUME and then tahan down POWER2. lepasin RESUME3. pencet RESUME twice, then lepasin POWER4. Let green light blink until printer is done futzingSelect function with RESUME pencet POWER to execute:pencetes – light color – functionNumber of pencetes – light color – function0 pencetes – green – Test print (or exit service mode on i960)1 pencet – orange – EEPROM info print (plus grid nozzle diagnostic on i960)2 pencetes – green – EEPROM initialize3 pencetes – orange – Reset waste ink counter
--------------------------------------------------------------------------------------------------
Canon S450 Printer
1: Power off printer2: Tahan Resume tombol then pencet and tahan POWER, the beeper will sound once.3: Tahan POWER and lepasin RESUME4: Pencet RESUME twice5. Lepasin Power tombol6: When the indicator lights steady, pencet RESUME three(3) times. The indicator should be orange.7: Pencet Power to set data
--------------------------------------------------------------------------------------------------
Canon BJC 1000 Serie
1: Remove Cartridge2: Unplug the AC Power Cord3: Tahan down the RESUME tombol4: Lepasin RESUME after plugging in the AC Power cord.5: Pencet the RESUME once within 5 seconds and lepasin the RESUME .6: Pencet and TAHAN RESUME for two seconds or more and lepasin it.7: Pencet and TAHAN RESUME for two seconds or more and lepasin it.8: Unplug AC Power Cord to set data.
--------------------------------------------------------------------------------------------------
Canon BJC-2000 BJC-2100 Serie
1: Remove the Cartridge2: Unplug the AC Power Cord3: Close Front access panel3: Tahan down the RESUME/RESET tombol and plug in the AC power cord4: Lepasin RESUME/RESET after plugging in the AC Power cord.5: Pencet the RESUME/RESET once within 5 seconds and lepasin the RESUME/RESET .6: Pencet and TAHAN RESUME/RESET for two seconds or more and lepasin it.7: Pencet and TAHAN RESUME/RESET for two seconds or more and lepasin it.8: Unplug AC Power Cord to set data.
--------------------------------------------------------------------------------------------------
Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650
Unplug Power CordTahan POWER and RESUME tombolsPlug in Power CordLepasin tombolsOpen front door of printerTahan the CARTRIDGE and RESUME tombolsPencet POWERLepasin all tombols after the beepsPencet CARTRIDGE sekaliPencet RESUME
--------------------------------------------------------------------------------------------------
Canon BJC-5000
1: Power off printer2: Pencet and tahan RESUME then pencet POWER, The indicator will start blinking.3: While the indicator is blinking , Pencet RESUME twice then Wait until the printer beeps to indicate service mode5: When the indicator lights steady GREEN, pencet RESUME four(4)times. The indicator should be GREEN.6: Pencet Power to set dataService Test Print1: Power off printer2: Pencet and tahan RESUME then pencet POWER, The indicator will start blinking.3: While the indicator is blinking , Pencet RESUME twice then Wait until the printer beeps to indicate service mode5: When the indicator lights steady GREEN, pencet RESUME two(2)times. The indicator should be GREEN.6: Pencet Power to PrintNozzle Print1: Power off printer2: Pencet and POWER, until the printer beeps and lepasin.Demonstration Print1: While the printer in ON , , Pencet and tahan RESUME until the printer plays a melody of beeps.
--------------------------------------------------------------------------------------------------
Canon BJC-5100
Self TestSwitch Printer off. Tahan Power for 1 beep.Waste Counter Reset1: Power off printer
2: Pencet and tahan RESUME then pencet POWER, The indicator will start blinking.3: While the indicator is blinking , Pencet RESUME twice then Wait until the printer beeps to indicate service mode5: When the indicator lights steady GREEN, pencet RESUME four(4)times. The indicator should be GREEN.6: Pencet Power to set dataService Test Print1: Power off printer2: Pencet and tahan RESUME then pencet POWER, The indicator will start blinking.3: While the indicator is blinking , Pencet RESUME twice then Wait until the printer beeps to indicate service mode5: When the indicator lights steady GREEN, pencet RESUME two(2)times. The indicator should be GREEN.6: Pencet Power to PrintNozzle Print1: Power off printer2: Pencet and POWER, until the printer beeps and lepasin.Demonstration Print1: While the printer in ON , , Pencet and tahan RESUME until the printer plays a melody of beeps.
--------------------------------------------------------------------------------------------------
Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500
1: Power off printer2: Tahan Resume tombol then pencet and tahan POWER, the beeper will sound once.3: Tahan POWER and lepasin RESUME4: Pencet RESUME twice5: When the indicator lights steady, pencet RESUME three(3) times. The indicator should be orange.6: Pencet Power to set data--------------------------------------------------------------------------------------------------i’ve try all codes for canon printers on this method works:1 – pencet resume tombol and then pencet power tombol2 – realese the resume tombol and pencet 2 more times then realese both3 – pencet and lepasin resume 4 times and power 2 times…
MPC 110 PROCEDURE FOR RESET…(also MP130)
* PENCET – “MENU- SCAN – COPY – SCAN”* PENCET “+” UNTIL YOU FIND – “NVRAM ACCESS” PENCET “OK”* PENCET “-” (MINUS) FOR (SET ABS-P LEVEL) PENCET “OK”* RESET LEVEL WITH “+”* PENCET “OK”* PENCET “-” (MINUS)* SET ABS-M LEVEL* PENCET “OK”* RESET LEVEL TO “0? WITH “+”* PENCET MENU TO RETURN TO SERVICE MENU – EXIT* TURN MACHINE OFF
POWER UP AS NORMAL….. GOOD LUCK
--------------------------------------------------------------------------------------------------
3. Cara Menggunakan SCCS untuk Epson All Series
* Idupin dulu printernya (biarin lampu tu kedap-kedip)* Lalu jalankan programnya Start-Program-SSC Service utility-SSC Service utility
* Sesuaikan configurasinya untuk printer anda, untuk epson C45 bisa gunakan C4x lalu klik tombol X alias di tutup* Klik kanan SSC service utility yang ada di System Tray.* Pada inkfresh nya restore value* Jangan lupa reset protection counter-nya(cari sendiri ya d situ).* Kalo udah matiin printernya lalu hidupin lagi (biasanya printer epson kesayangan kita dah normal lagi)
4. Cara Reset HP All in One
* Reinitializing the all-in-one* Reinitialize the all-in-one by following the steps below:* Turn off the power by pressing ON.* Unplug the power cord.* Wait five seconds, then plug in the power cord and turn on the power.* Try reading the photo card again.* If the unit fails to read the card, reset the unit:* Repeat Steps 1 and 2 above.* Press and hold # and 6 from the front panel keypad while plugging in the power cord.* For products that do not have # and 6, press Cancel and the Right Arrow.* Continue holding both buttons until the reset displays, and then release.* Select the language and country/region if prompted.* Huom: Resetting the unit will erase some stored data. Most of this data will be restored when the all-in-one re-establishes communication with the computer.
Cara lain
IssueThe product displays an 0x … error code when printing (for example Error: 0xf0af8004). These error codes indicate that the product has an internal condition.SolutionUse the instructions below to resolve the issue by restarting the product.
* Disconnect the Universal Serial Bus (USB) cable from the back of the product, but leave the product turned on.* Open the cover of the product and remove the print cartridges.* Close the cover and wait for the Insert Ink Cartridges message to display.* Disconnect the power cord from the back of the product and wait for one minute.* Reconnect the power cord. If the product does not automatically turn on, press the Power button.* Open the cover and reinsert the print cartridges.* Close the cover. If prompted, print a calibration page.* Reconnect the USB cable, and try to print a print job from the computer.