REBAR ACCESSORIES

E10 REBAR J-HOOK

E6Z REBAR TIE SPLICER

E6Z DOUBLE REBAR TIE SPLICER

Single splicer develops the 9,000 lb. (40.0 kN) working load and

18,000 lb. (80.1 kN) ultimate of WILLIAMS 1/2" high tensile tie

rod. Special design matches the angle of the serrations on the

rebar for maximum strength. Recommended torque on U-bolt

hex nuts is 40-ft. lbs. Available for No. 8 through No.11 rebar.

Double Rebar-Tie Splicers for 5/8" & 3/4" Tie Rods

Double splicer develops the full 19,000 lb. (84.5 kN) working load

and 38,000 lb. (169 kN) ultimate strength of WILLIAMS 3/4" high

tensile tie rods. Special design matches the rebar serration angle

to develop maximum strength. Available for No. 8 through No.11

rebar. Recommended torque on U-bolt hex nuts is 40-ft. lbs.

Also works with WILLIAMS 5/8" high tensile tie rods with an

11,250 lb. (50.0 kN) working load and 22,500 lb. (100 kN)

ultimate.

WILLIAMS Rebar J-Hook is an approved method of anchoring to

the rebar. Most popular uses include Nuclear Plants where weld-

ing to the rebar is not permitted and tying down battered wall

forms to resist uplift. J-Hooks are available in 3/8" and 1/2" diam-

eters for most popular rebar sizes.

State Rebar size (A) and J-Hook length (B) when ordering.

Rebar-Tie Splicer for 3/8" Tie Rods

Designed to work with WILLIAMS 3/8" high tensile tie rods.

Splicer develops a 4,900 lb. (21.8 kN) working load and 9,800 lb.

(43.6 kN) ultimate strength. Standard sizes for No. 6 through No.

14 rebar. Recommended torque of U-bolt hex nuts is 40 ft. Lbs.

Williams coupled reinforcing with rolled threads is the most con-

venient field connection possible. The high tensile couplings are

designed to exceed the full ultimate tensile strength of the thread-

ed rebar. Couplings and threaded rebar are available from

Williams in almost every standard diameter. They offer a tremen-

dous savings over field welding methods. Williams coupled rebar

meets the ACI code requirement 318-78 section 12.15.3 for

mechanical connections.

C2T COUPLED REBAR

E9B LIGHTWEIGHT SPICER

For Full Strength Rebar Couplings

See page 13 for C1T and C2T Couplings

or page 30 for C2D Flanged Couplings

A B

Patent No. 4,080,084

Patent No. 4,080,084

REBAR ACCESSORIES

E7Z REBAR BULKHEAD CLAMP

E5Z REBAR-LAPP SPLICER/LIGHT DUTY

E5Z DOUBLE REBAR-LAPP SPLICER/HEAVY DUTY

Light duty splicer with continuous strength for difficult forming

situations.

Rebar Bulkhead Clamps are designed for use on large or

small bulkheads when the rebar must run continuous.

The clamp uses Williams standard steel or malleable

wedge for fast assembly and minimum material costs.

Wedge clamp available up to No.8 Rebar. Rebars of

larger sizes use nuts and washers.

Rebar

Reccommended

Torque on Hex

Nuts

Working Load 2

to 1 S.F.

Lbs./kN

Average

Ultimate

Lbs./kN

*#4 & #5 15 ft. lbs. 3,750/ 16.7 7,500/ 33.4

#6 & #7 40 ft. lbs. 5,000/ 22.2 10,000/ 44.4

#8 thru #10 40 ft. lbs. 7,500/ 33.3 15,000/ 66.7

#11 40 ft. lbs. 10,000/ 44.5 20,000/ 89.0

Rebar

Working Load

2 to 1 S.F.

Lbs./kN

Average Ultimate

Lbs./kN

#6 & #7 10,000/ 44.5 20,000/ 89.0

#8 thru #10 15,000/ 66.7 30,000/ 133.4

#11 20,000/ 89.0 40,000/ 178.0

Ultimate Strengths to 40,000 lbs.

New rebar-lapp splicer designed for continuous strength of up to 40,000

lbs. Ties rebar together for use with tie rods. Recommended torque on

U-bolt hex nuts is 40-ft. lbs.

*Style different than shown (see detail A)

E9B

Lightweight Splicer

E-10

Rebar J-Hook

E5Z

Rebar-Lapp

Splicer

(Light Duty)

J7P

Rebar Collar

(shown on page 27)

C5T Threaded Shebolt

(shown on page 6)

D4M Hex-Lock Bracket

(shown on page 7)

E7Z Rebar

Bulkhead Clamp

Patent No. 4,080,084

Patent No. 4,080,084

Detail A