rear discharge hm (spreadslite)
DESCRIPTION
ÂTRANSCRIPT
1
Lancaster Parts & Equipment 2008 Horseshoe Rd, Lancaster PA 17602
lancasterpartsandequipment.comPh: 717 299-3296 Fax: 717 299-2382
ILLUSTRATED PARTS BREAKDOWN
Rear DischargeAuger Out
2 3
PTO Shaft.....................................................................3Main frame....................................................................4Wheels, Hubs, Bearings................................................5Main pulleys & Belts......................................................6Idler Pulleys / Front shield.............................................7Front Bearing Grease Hoses /Feed Hopper Spinner....8Front Doors & Side Shields...........................................9Main Hammer Mill (Top) + Screen Door.......................10Main Hammer Mill (Bottom)..........................................12Hammer Drum .............................................................13Dust Collector & Cyclone..............................................14Discharge Auger............................................................16Hydraulics.....................................................................18Feed Auger Arm............................................................20Hyd. Hand Pump, Feed Auger Cylinder........................21Line Shaft - Rear cuppling.............................................22Rear Gearbox + Rear Auger Drive................................23Feed Auger Top.............................................................24Feed Auger Bottom.......................................................26
2
4
3
LHM173 = H.M. End1-3/4 Spline
4
2
1
LHM174 =Tractor End1-3/4 Spline LHM173 =Tractor End1-3/8 Spline
BOM ID PartNo Description Qty1 LHM410 PTO Cover (small end) 12 302-5500 Cross Bearing Kit 23 LHM411 PTO Cover (big end) 14 921-4400 Shield Bearing Kit 2
Item Part# Description QTY1 LHM410 PTO Cover (Small End) 12 302-5500 Cross Bearing Kit 23 LHM411 PTO Cover (Large End) 14 921-4400 Shield Bearing 2
Table of Content
4 5
Item Part# Description QTY1 HP-12180 Hyd. Hand Pump 12 HMFRA170 Hitch 13 Jack Jack (Side Wind) JDS07-28PP 14 HMFRA185 Jack Holder Plate 15 DRUHOU148 PTO Holder Arm 16 HM40624 Feed Auger Holder 17 DRUHOU233 Screen Holder Channel 28 HM40629 Platform 1
Item Part# Description QTY1 LHM269 Wheel Shaft 22 Cotter 3/16 X 2” Cotter Pin 23 SE16289 Grease Seal 24 LM69349 Inside Wheel Bearing 25 LM69310 Inside Bearing Race 26 LHM266 Wheel Hub 27 LM67010 Outside Bearing Race 28 LM67048 Outside Bearing 29 LHM264 Washer 2
10 LHM263 Wheel Castle Nut 211 LHM262 Hub Cap 212 LHM261 Rim 213 LHM259 Tire 214 LSC426 Axle - Hub Assembly 2
13
12
13
12
213 4 5 6 7 8 9 10 11
213 4 5 6 7 8 9 10 11
14
8
6
1
5
7
2
3
4
8
6
1
5
7
2
3
4
6 7
Item Part# Description QTY1 PLU5V7.1.8 5V, 8 grove Pulley 12 SF-2.4375 SF 2½” Bushing 13 Key 5/8” X 1/2” Key 14 5VX740 Gates 5VX 740 Belts 85 PUL5V16.0.8 5V 8 Groove,16” Pulley 16 F-2500 F 2½” Bushing 17 Key 5/8” X 5/8” Key 18 PUL5V14.3 5V 3 Groove, 14” Pulley 19 E-1750 E 1¾’’ Bushing 1
10 Key 3/8” X 3/8” Key 111 PUL5V6.3.3 5V 6.3, 3 Groove Pulley 112 SK-2500 SK 2½” BUSHING 113 Key 5/8” X 3/8” Key 114 BOLT 5/8”-11 Bolt 115 PULID5X2.5 Idler Pully 5” x 2¼ 116 5/8WAS Stack of 5/8 washers ?17 NUT 5/8”-11 Bolt Stover Lock Nut 118 LSC442 6” Adjuster Rod 119 5VX650 Gates 5VX 650 Belts 3
Item Part# Description QTY1 HM40630 Shield / Idler bracket 12 HM40631 Idler Access Cover 13 TAPBOL ½” x 7” Machine Bolt Hex Tap - Grade #5 14 LHM182 Spring 15 LHM198 Idler Bracket 16 COLLAR1.1250 1-1/8 Shaft Collar 37 WAS-N14-1250-P Shim Washer ?8 OSPA outside spacer 1-1/16” long 29 MSPA inside spacer 1-13/16” long 1
10 HM40647 1-1/8” Shaft 111 BOFH-NC.625X8 5/8’’ by 8’’ Flat SOC Bolt NC #5 112 nut ½’’-13 Stover locknut 113 PULID6.5X3.0 6½’’ X 3” Idler Pulley 1
1214
10
17
1811
19
16 15
13
8
59
7
4
6
1
23
1214
10
17
1811
19
16 15
13
8
59
7
4
6
1
23
611
8
5
13
7
9
8
6
2
12
13
4
1
3
10
611
8
5
13
7
9
8
6
2
12
13
4
1
3
10
8 9
Item Part# Description QTY1 ZERSTR 1/8’’ Straight Grease Zert 22 PP-2GCO 1/8” Galv. Coupling 23 Washer 3/8 Washer 24 BGRH3 Bottom Grease Hose 15 TGRH1 Top Grease Hose 16 129768 2-7/16 Grip Tight Bearing 27 FB-2500 2 1/2” 4 Holed, piloted Bearing 1
96
1
2 341
57 8
1096
1
2 341
57 8
10
Item Part# Description QTY1 FB-11250 1-1/8” Three Holed Flange Bearing 22 HM40188 Spinner 13 HM40623 Bearing Plate 14 Key ¼” X ¼” Key 15 LOVJ1.125 Love-Joy 1.1/8” Bore 1/4 Key (type L100) 16 LOVJSPI Love-Joy Rubber Spider for type L100 17 LOVJ1.00 Love-Joy 1” Bore 1/4 Key (type L100) 18 FEEAUG453 Hyd. Motor Mount 19 Key 1” X ¼” Woodruff Key 1
10 HM-01012 CL101-1012 Hyd Motor 1
Item Part# Description QTY1 HM40536 Top Shield Door 12 HM40537 Bottom Shield Door 13 SHI246 PTO Shield Bracket 14 SHI245 PTO Cover Pin 15 SHI244 PTO Cover 16 HM40651 Door Pin 17 HM40655 Shield Side 18 LSC159 Hold-Down Strap Hook 49 LSC158 Hold-Down Strap U Bracket 4
10 LSC157 Hold-Down Strap 4
1
2
3
8
5
7
9
4
6
10
1
2
3
8
5
7
9
4
6
101
7
32
4
1
6
5321
7
32
4
1
6
532
10 11
Item Part# Description QTY1 HM30111 Main Front Plate 12 HM30116 Drum cover Plate 23 HM30152 Hammer Rod Hole Cover 24 129768 2-7/16 Piloted Flange Grip Tight Bearing 25 HM40639 Spinner Hole Cover Plate (for removing the spinner) 16 HM41MAG Magnet 27 HM40112 Top Right Hopper Plate 18 HM40114 Right Drum Side 19 HM40113 Top Left Hopper Plate 1
10 HM40145 Left Drum Side 111 HM40130 Screen Holder Bracket 412 HM40153 Bottom Screen Bar 113 HM30111 Main Front Plate 114 HM40130 Screen Holder Bracket 215 DRUHOU270 1/2’’ Pin For Screen Holder #40 216 HM40638 Back Spinner Hole Cover Plate 117 PP-125BY6 1/8’’ Pipe to 1/8’’ Pipe 6’’ Long Nipple, 118 PP-2GCO 1/8” GALV. COUPLING 119 ZERSTR 1/8’’ Straght Grease Zert 1
20 HM40648 Corn Deflector ( this part is optional, not included with all models) 1
21 PINCL-NC.125X2.500 1/8” x 2 1/2” Hair Pin Clip 222 HM40134 Drum Door 123 DRUHOU284 Screen Door Adj. Rod 224 HM30165-L L.H. Side Door Latch 125 HM30165-R R.H. Side Door Latch 126 HM30136 Screen Door Side Filler Strips 2
Standard with each mill comes 2, 1/4” Screens, 2, 5/16” Screens & 2, 3/8” Screens. Part # are as Follows: 1/4” Screens = HM40186-.255/16” Screens = HM40186-.3125 3/8” Screens = HM40186-.375Also available are: 1/8” Screens = HM40186-.1253/16” Screens = HM40186-.187 1/2” Screens = HM40186-.50 5/8” Screens = HM40186-.625
1918
317
4
2
16
11
8
13
12
21
10
11
207
9
1
14
3
6
2
5
Screen
4
15
1918
317
4
2
16
11
8
13
12
21
10
11
207
9
1
14
3
6
2
5
Screen
4
15
26
25
23
22
23
2426
26
25
23
22
23
2426
12 13
Item Part# Description QTY1 HM40127 Plate Bottom of Door 22 HM40519 Transition Plate 23 HM40510 Bottom 10” Tube 14 HM40506 Bottom Auger 15 HM40514 Auger Holder Bracket 16 FB-11250 1-1/8” Three Holed Flange Bearing 17 HM30146 Bearing Plate 18 FB-2500 2 1/2” 4 Holed, piloted Bearing 1
1
2
6
5
23
4
78
11
2
6
5
23
4
78
1
1
6
3
8 7
5
4
4
2
6 10
9
1
6
3
8 7
5
4
4
2
6 10
9
Item Part# Description QTY1 HAMDRU175 Hammer-drum Shaft 12 HAMDRU314 Hammer-drum Plates 263 HAMDRU322B Hardened Hammer Rod 34 HAMDRU316D Hard Faced Hammers 1505 HAMDRU315A 1/2” Hammer Spacers 1506 HAMDRU321-0 Hammer Drum Spacer 3 Ga (¼”) 1277 HAMDRU321-A Hammer Drum Spacer 20 Ga 258 HAMDRU321-B Hammer Drum Spacer 10 Ga 259 N14 Shaft Nut 2
10 W14 Shaft Washer 2
14 15
1312
15
1
211
10
4
3
9
5
14
6
8
7 1312
15
1
211
10
4
3
9
5
14
6
8
7
Item Part# Description QTY1 DUSCOL359 Transition pc. 12 HM30118 Dust Collector Back plate 13 HM30119 Dust Collector Band 14 DUSCOL409 Cut-Off Plate 15 HM30120 Dust Collector Front Plate 16 HM30144 Dust Collector Cover 17 HM40208 Small H.M. Cyclone 24” 18 DUSCOL406 Adapter Sleeve 19 SD-175 SD 1¾” Bushing 1
10 HM30139 Blower Fan Center 111 HM30138 Fan Paddle 312 HM30117 Dust Collector Spacer 1/4” 213 HM30117-2 Dust Collector Spacer 1/8” 114 Bolt 3/8”-16 X 5¾” Bolt 1215 Nut 3/8” lock-nut 10
This page intentionally left empty
16 17
6
5
7 15
2
14
4
14
3
8
1
139
101211
6
5
7 15
2
14
4
14
3
8
1
139
101211
2
1
3
4
2
1
3
4
Item Part# Description QTY1 HM40580 Main 12” tube 12 HM40579 Top 12” tube 13 SA1228 60° 12” to 10” Discharge Spout 14 SA1228A 60° 12” to 10” Discharge Spout top strap 15 HM40584 End Plate 16 FB-12500 1¼ Bearing 17 HM40560 Auger 18 LE73996 Spline hub 19 HM40576-0 Bottom Plate 1
10 SA1230 Gear Box Mount Plate 111 DISAUG363 Small Gear Box, Medium arm 112 BOTAUG452 Spacer Washer 813 HM40589 Clean Out Hole Cover 114 HM40587 Swivel Plate 415 HM40588 Spacer Plate 1
Item Part# Description QTY1 HM40616 Top strap 12 HM40586 Bottom Strap 13 HN40529 HM RH Support Strap 14 HN40528 HM LH Support Strap 1
18 19
1
10
10
12
4
5
6
32
7
3
1
8
3
1
10
10
12
4
5
6
32
7
3
1
8
3
7
13
3
9
1
13
2
3
38
12
11
10
10
11
12
7
13
3
9
1
13
2
3
38
12
11
10
10
11
12
7
3
1
3
13
1510
10
2
12
3
9
11
13
8 14
7
3
1
3
13
1510
10
2
12
3
9
11
13
8 14
14
14
13
8
14
14
13
8
This flow control is mounted on the Feed Auger
This flow control is mounted on the side of the Front Shield
These Hoses go to the hyd. motor on top of the Feed auger
Hopper Spinner MotorTractor ends
Item Part# Description QTY1 HV-30003 HFV-3 Port Flow Control Valve 22 TF-8FP-8FP-8MP 5602 Adapter 23 JP-8MJ-8MP #8 Male JIC - #8 Male Pipe Adapter 64 JP-8MJ-8MP-45 #8 Male JIC - #8 Male Pipe 45° Adapter 15 FEEAUG457 Hyd. Hose (Flow Control - Bottom of Motor) 16 FEEAUG456 Hyd. Hose (Flow Control - Top of Motor) 17 HYD HOSE Hyd. Hose (Connecting two flow controls) 18 HYD HOSE Hyd. Hose (Feed Auger To Tractor) 19 JP-8MJ-8MP-90 #8 Male JIC - #8 Male Pipe 90° Adapter 1
10 JB-8MJ-8MB #8 Male JIC - #8 Male Boss 411 HYD HOSE Hyd. Hose (Spinner Motor - Flow Control) 112 HYD HOSE Hyd. Hose (Flow Control - Spinner Motor) 113 HYD HOSE Hyd. Hose (Return to To Tractor) 114 QC-28881 Quick Connect Male 215 HM-01015 101-1015 Char-lynn Or Eagle Motor 116 MB-875 7/8” Hose Holder 417 HM-01012 101-1012 Char-Lynn Motor 118 FEEAUG473 Motor Mount 1
5
6
10
10 17
18
5
6
10
10 17
1816
C
CB
B
20 21
11
10
9
1
13
543
7
8
12
2
465
11
10
9
1
13
543
7
8
12
2
465
Item Part# Description QTY1 HM40542 Feed Auger Mounting Arm 12 FEEAUG161 Auger Holder T 13 FEEAUG162 Mounting Shaft 14 COLLAR1.500SS 1-1/2” Single Split Collar 25 Bolt ½’’-12 X 1¼” Bolt 26 Lock Washer ¼” Lock Washer 27 FEEAUG163 Placement Collar 18 FEEAUG311 Cylinder Holder Bracket 19 HM40571 Mounting Arm Shaft 1
10 FEEAUG159-1 Half Moon Placement Plate 111 COLLAR2.00SS 2” Single Split Collar 112 SP153 1-3/4” Single Split Collar 113 9540K756 Rubber bumper 1
7
7210
4
89
5
6
3
1
7
7210
4
89
5
6
3
1
Item Part# Description QTY1 HP-12180 Hyd. Hand Pump. 12 HC-2X8-STR 2” X 8” Stroke 1¼” Rod 13 JB-4MJ-4MB90 #4 Male JIC - #6 Male Boss 90 degree Adapter 14 Hose from Hand Pump to Feed Auger Cylinder 15 JB-4MJ-6MB #4 Male JIC - #6 Male Boss Adapter 16 Bolt 3/4” x 4½” Machine Bolt 17 Nut 3/4” NC Stover Lock Nut 28 BB-6MB-8FB #6 Male Boss - #8 Female Boss Adapter 19 HF-8-SAE #8 SAE Breather Plug 1
10 Bolt 3/4” x 3½” Machine Bolt 1
22 23
Item Part# Description QTY1 DRUHOU141A Line shaft 12 BERPB2.50 2½” Pillow Block Bearing 13 HM40637 Door Stop 24 9540K756 Rubber bumper 25 HM40634 Cupling Cover 16 1080HUB2.5 Coupling 1080 2½’’ Bore 17 LSC439 Cover & Grid Assembly 18 LSC441 Coupling 1080 1¾’’ Bore 19 Key 3/8” X 3/8” Key 1
10 HMSHI151 Line shaft cover 1
98
6
5
23
4
1
10
234
98
6
5
23
4
1
10
234
6
3
7
85
1
13
8
17
9
16
2
11
15 14
12
4
6
3
7
85
1
13
8
17
9
16
2
11
15 14
12
4
Item Part# Description QTY1 HM4035 Main reduction gearbox 12 HM40652 PTO Shield Bracket 13 HM40654 PTO Shield 14 HM40632 Belt Shield 15 HM4038 Gearbox Mount 16 HM40626 Gearbox Mounting Base 17 HM40585 Bottom Grearbox shield 18 SK-1375 SK 1.3/8 Bushing 2
9 PUL5V7.5 3 5V pulley 7.5” O.D. 3 Grove (2013 Model has a 8.5” 2 grove pulley) 1
11 PUL5V6.3.2 5V Pulley 6.3” O.D. 2 Groove(2013 Model has a 6.3” 2 grove pulley) 1
12 SA1230 Gear Box mount Plate 113 DISAUG362 Small Gear Box (short Arm) 114 PULID5X3 Wide Idler Pulley 5” x 3” 115 LSC442 6” Adjuster Rod 116 5VX490 5VX 490 Belt (may be a 5vx500 ? as of pinting of parts book) 117 HM4039 Gearbox Mounitng Bar 1
24 25
14
15
16
17
12
12
12
18
11
10 12
12
13
14A
1214
15
16
17
12
12
12
18
11
10 12
12
13
14A
12
7
1
2
3
4
6
58
9
7
1
2
3
4
6
58
9
Item Part# Description QTY1 HM-01012 101-1012 Char-Lynn Motor 12 FEEAUG473 Motor Mount1 13 C5016X1 Coupling Chain # 1’’ Bore 14 C5016 Coupling Chain #50 15 C5016X1-1/8 Coupling Chain # 1-1/8’’ Bore 16 KEY ¼” x ¼” Key 17 W- Key 1” x ¼” Woodruff Key 18 FB-11250 1-1/8” Three Holed Flange Bearing 19 FEEAUG449 Top Plate 1
10 FEEAUG441 Main Auger Tube 111 FEEAUG448 Feed Auger Auger 112 FEEAUG445 Half Moon Holders 613 FEEAUG446 Flow Control Mount 114 FEEAUG444 60° Discharge Spout 115 FEEAUG420 Top Mounting Bracket 116 FEEAUG421 Middle Mounting Bracket 117 FEEAUG447 Bottom Mounting Bracket 118 MB-875 7/8” Hose Holder 5
26 27
12
68
7
6
5
2
4
10
2014 and newermodels do not have these
3
11
91
12
68
7
6
5
2
4
10
2014 and newermodels do not have these
3
11
91
Item Part# Description QTY1 FEEAUG455 Auger Guard 12 FEEAUG442 Bottom tube 13 FEEAUG19774 Auger Holder Basket 14 FEEAUG450 Short Feed Auger 15 FEEAUG452 Hopper Holder Arm 16 LSUNY12 Yoke with spline 17 FEEAUG462 Knuckle Bracket 18 2001400 Weasler 14 series Yoke Cross Bearing Kit 19 MSC-00250449 Snap Latch 1
10 FEEAUG463 Lid 111 FB-12500 1¼” Bearing 112 FEEAUG613 Grease / Clean-out Hole Cover 1