radio management
TRANSCRIPT
RCPCFNET_1
OPERATING / MAINTENANCE SHEETCSCN GSM RCPCFNET_1
FUNCTION : CONFIGURATION MANAGEMENT
SUB-FUNCTION : MANAGING GSM RADIO ENVIRONMENT OF THE RCP
1 PURPOSERCPCFNET_1 describes the basic operations to manage the radio environment in the GSM network.This includes:
- local radio environment (BSC, local LAC, cells),
- adjacent radio environment (adjacent MSC LACs and adjacent VLR LACs).
2 WHEN TO USE RCPCFNET_1 ?Use RCPCFNET_1 when you want to configure the GSM radio environment at the RCP.
3 WARNINGNone.
4 QUICK REFERENCE GUIDEYou can:
- create a BSC, using command CREBSC (see FOP CREBSC),
- delete a BSC, using command DELBSC (see FOP DELBSC),
- interrogate a BSC, using command INTBSC (see FOP INTBSC),
- modify a BSC, using command MODBSC (see FOP MODBSC),
- create a new local LAC , using command CREREV (see FOP CREREV),
- assign a cell to another LAC, using commands DELREV (see FOP DELREV) and CREREV (see FOPCREREV),
3BL 41292 DAAA REAGA Ed. 01 1 / 23
RCPCFNET_1
- delete a local LAC and reassign the cells, using commands DELREV (see FOP DELREV) and CREREV(see FOP CREREV),
- interrogate a local LAC , using command INTREV (see FOP INTREV),
- modify cell characteristics, using command MODREV (see FOP MODREV),
- create a LAC in an adjacent radio environment, using commands CREAML (see FOP CREAML) andCREAVL (see FOP CREAVL),
- delete a LAC in an adjacent radio environment, using commands DELAML (see FOP DELAML) andDELAVL (see FOP DELAVL),
- interrogate a LAC in an adjacent radio environment, using commands INTAML (see FOP INTAML)and INTAVL (see FOP INTAVL).
2 / 23 3BL 41292 DAAA REAGA Ed.01
RCPCFNET_1
5 DETAILED GUIDE
5.1 How to create a BSC5.1.1 Preconditions
The semi-permanent links that enable the RCF-BSC and RCF-adjacent MSC dialogs must already existin the SSP.
5.1.2 Creating a BSC
To create a BSC at the CSCN:
a) Check that the routing to the BSC is correct:
• for analysis, using commands ANSIN (see FOP ANSIN) and ANSIL (see FOP ANSIL),
• for routing, using commands ASMIN (see FOP ASMIN) and ASMIL (see FOP ASMIL),
• for the circuit groups, using command FSMIN (see FOP FSMIN),
• for the signaling links, using command CSMIN (see FOP CSMIN).
b) Check that the BSC that you want to create does not exist at the RCP, using command INTBSC (seeFOP INTBSC) and follow the instructions in the following table.
If... then...
the BSC does not exist create the BSC, using command CREBSC (see FOP CREBSC).
It is recommended to assign the LAC value to the “a” BSCTYP pa-rameter (see Table 2) to optimize the BSC-LAC congestion manage-ment.
If the BSC is equipped with transcoders that support AMR, use theAMR values (see value k in Table 2). This is only applicable if thecorresponding functional option is activated.
If the BSC is already created a) check the BSC characteristics (CPD, BSC name and number),using command INTBSC (see FOP INTBSC),
b) if necessary, modify the BSC characteristics, using commandMODBSC (see FOP MODBSC).
For a list of the parameters to use in the CREBSC, INTBSC and MODBSC commands, see AppendixA.
c) End.
5.2 How to delete a BSC5.2.1 Preconditions
The BSC must exist.
3BL 41292 DAAA REAGA Ed. 01 3 / 23
RCPCFNET_1
5.2.2 Deleting a BSC
To delete a BSC:
a) Delete the BSC cells in the RCP, using command DELREV (see FOP DELREV).
For a list of the parameters to use in the command DELREV, see Appendix B.
b) Request the deletion of the corresponding cells in the BSS.
c) Delete the BSC in the RCF, using command DELBSC (see FOP DELBSC).
For a list of the parameters to use in the command DELBSC, see Appendix A .
d) If a LAC is deleted, then delete any associated part of the radio environment for the adjacent MSCsand VLRs, using commands DELAML (see FOP DELAML) and DELAVL (see FOP DELAVL).
For a list of the parameters to use in the DELAML command, see Appendix C.
For a list of the parameters to use in the DELAVL command , see Appendix D.
e) End.
5.3 How to interrogate a BSC5.3.1 Preconditions
The BSC must exist.
5.3.2 Interrogating a BSC
To interrogate a BSC:
a) List the BSC values, using command INTBSC (see FOP INTBSC).
For a list of the parameters to use in the INTBSC command, see Appendix A.
b) End.
5.4 How to modify a BSC5.4.1 Preconditions
The BSC must exist.
5.4.2 Modifying a BSC
To modify a BSC:
a) List the BSC type values, using command INTBSC (see FOP INTBSC).
b) Modify BSC type values, using command MODBSC (see FOP MODBSC).
Note : If the BSC is equipped with transcoders that support AMR, modify the AMR values,if necessary.
For a list of the parameters to use in the MODBSC command, see Appendix A.
c) End.
4 / 23 3BL 41292 DAAA REAGA Ed.01
RCPCFNET_1
5.5 How to declare a new local LAC5.5.1 Preconditions
None.
5.5.2 Declaring a new local LAC
To declare a new local LAC:
a) Identify the BSC to be associated with the LAC.
b) Check that the LAC does not already exist as a LAC adjacent to an MSC or VLR, using commandINTREV (see FOP INTREV).
c) Create the LAC and the cells for the LAC that are managed by the BSC in the RCP, using commandCREREV (see FOP CREREV).
For a list of the parameters to use in the CREREV command , see Appendix B.
d) Request the creation of the LAC and the associated cells in the BSS.
e) Declare the LAC in the adjacent radio environment for the adjacent MSC and VLR, using commandsCREAML (see FOP CREAML) and CREAVL (see FOP CREAVL).
For a list of the parameters to use in the CREAML command, see Appendix C.
For a list of the parameters to use in the CREAVL command, see Appendix D.
f) Update the regional subscription zone codes and the accepted national roaming PLMNs. For moreinformation, see FEX CSMBABOR and RCPMBROAMN.
g) If you want to associate a new local LAC to this BSC, repeat steps a) to f).
h) End.
5.6 How to assign a cell to another LAC5.6.1 Preconditions
None.
5.6.2 Assigning a cell to another LAC
To assign a cell to another LAC:
a) Check in the RCP that the target LAC exists, using command INTREV (see FOP INTREV), and usingthe following table.
If... Then...
the LAC exists check that the cell identification number does not exist in the LAC
the LAC does not exist proceed to the next step
b) Determine the optimum time to create the LAC, in order to minimize traffic disruption.
New traffic is refused until the RCP and the BSC are updated.
3BL 41292 DAAA REAGA Ed. 01 5 / 23
RCPCFNET_1
c) Delete the cell assignment to the LAC in the RCP, using command DELREV (see FOP DELREV) andrequest a BSS update.
For a list of the parameters to use in the DELREV command, see Appendix B.
d) Create the new LAC and cell in the RCP, using command CREREV (see FOP CREREV).
For a list of the parameters to use in the CREREV command, see Appendix B.
For more information about the procedure for declaring a new local LAC, see section 5.5.2.
e) End.
5.7 How to delete a local LAC and reassign the cells5.7.1 Preconditions
- The LAC must be in the adjacent VLR or RCF environment (see FEX RCPCFNET_3).
If the LAC is used aspart of...
then before deleting the LAC at theRCF...
using command...
a regional subscriptionzone
delete the LAC from the subscription zonecodes
MODZOC (see FOP MOD-ZOC)
an accepted nationalroaming PLMN
delete the LAC from the accepted nationalroaming PLMNs list
DELAPL (see FOP DE-LAPL)
5.7.2 Deleting a local LAC and reassigning the cells
To delete a local LAC local and reassign the cells:
a) Delete the LAC in the adjacent MSC and VLR environments, using commands DELAML (see FOPDELAML) and DELAVL (see FOP DELAVL).
For a list of the parameters to use in the DELAML command, see Appendix C.
For a list of the parameters to use in the DELAVL command, see Appendix D.
b) Identify the cells assigned to the LAC that you want to delete, using command INTREV (see FOPINTREV).
c) Check that an LAC for reassigning the cells exists in the RCF, using command INTREV (see FOPINTREV), and use the following table.
If... then...
the LAC is created check in the RCF that the cell identification numbers are not as-signed to this LAC
the LAC is not created proceed to the next step
For a list of the parameters to use in the INTREV command, see Appendix B.
d) Determine the optimum time to create the LAC, in order to minimize traffic disruption in the network.New traffic is refused until the RCF and the BSS are updated.
6 / 23 3BL 41292 DAAA REAGA Ed.01
RCPCFNET_1
e) Determine the optimum time for changing each individual cell.
f) Delete the cells in the old LAC at the RCF, using command DELREV (see FOP DELREV).
Note : The LAC is only deleted when there are no more assigned cells.
For a list of the parameters to use in the command DELREV, see Appendix B.
g) Reassign the cells in the RCF to the new LAC and to the new geographical area, using commandCREREV (see FOP CREREV).
For a list of the parameters to use in the CREREV command, see Appendix B.
To create a local LAC, see section 5.5.2.
h) Request a cell update in the BSS.
i) End.
5.8 How to interrogate a local LAC5.8.1 Preconditions
None.
5.8.2 Interrogating a local LAC
To interrogate a local LAC:
a) List the local LAC values, using command INTREV (see FOP INTREV).
For a list of the parameters to use in the INTREV command, see Appendix B.
b) End.
5.9 How to modify cell characteristics5.9.1 Preconditions
None.
5.9.2 Modifying the cell characteristics
To modify the characteristics of a cell:
a) List the cell characteristics, using command INTREV (see FOP INTREV).
b) Modify the geographical area, location address, charging zone number, location information (lat-itude, longitude, and radius), using command MODREV (see FOP MODREV).
For a list of the parameters to use in the MODREV command, see Appendix B.
c) If necessary, delete all the cell location information for all the cells in the list by setting the RADIUSparameter to 0 (zero), using command MODREV (see FOP MODREV).
d) End.
3BL 41292 DAAA REAGA Ed. 01 7 / 23
RCPCFNET_1
5.10 How to create a LAC in an adjacent radio en-vironment
5.10.1 Preconditions
None.
5.10.2 Creating a LAC in an adjacent radio environment
To create a LAC in an adjacent radio environment:
a) Check that the LAC is adjacent to the RCF.
b) Check that the routing to the BSC is correct, using the following query and/or listing commands:
• for analysis, using commands ANSIN (see FOP ANSIN) and ANSIL (see FOP ANSIL),
• for routing, using commands ASMIN (see FOP ASMIN) and ASMIL (see FOP ASMIL),
• for the circuit groups, using command FSMIN (see FOP FSMIN),
• for the signaling links, using command CSMIN (see FOP CSMIN).
c) Create LACs for adjacent MSCs and VLRs, using commands CREAML (see FOP CREAML) andCREAVL (see FOP CREAVL).
For a list of the parameters to use in the CREAML command, see Appendix C.
For a list of the parameters to use in the CREAVL command , see Appendix D.
Note : In the case of an inter-PLMN handover, this LAC can belong to another PLMN.
d) End.
5.11 How to delete a LAC from an adjacent radioenvironment
5.11.1 Preconditions
None.
5.11.2 Deleting a LAC from an adjacent radio environment
To delete a LAC from an adjacent radio environment:
a) Delete a LAC from an adjacent radio environment, using commands DELAML (see FOP DELAML)and DELAVL (see FOP DELAVL).
For a list of the parameters to use in the DELAML command, see Appendix C.
For a list of the parameters to use in the DELAVL command, see Appendix D.
b) End.
8 / 23 3BL 41292 DAAA REAGA Ed.01
RCPCFNET_1
5.12 How to interrogate a LAC in an adjacent radioenvironment
5.12.1 Preconditions
None.
5.12.2 Interrogating an LAC in an adjacent radio environment
To interrogate a LAC in an adjacent radio environment:
a) List the characteristics of the adjacent radio environment, using commands INTAML (see FOP IN-TAML) and INTAVL (see FOP INTAVL).
For a list of the parameters to use in the INTAML command, see Appendix C.
For a list of the parameters to use in the INTAVL command, see Appendix D.
b) End.
3BL 41292 DAAA REAGA Ed. 01 9 / 23
RCPCFNET_1
6 RELATED DOCUMENTSSEE:
- Operator guide: Configuration management, CSCFGOP.
- Operator sheets: ANSIL, ANSIN, ASMIL, ASMIN, CREAML, CREAVL, CREBSC, CREREV, CSMIN,DELAML, DELAPL, DELAVL, DELBSC, DELREV, FSMIN, INTAML, INTAVL, INTBSC, INTREV, MODBSC,MODREV and MODZOC.
- Maintenance sheets: CSMBABOR and RCPMBROAMN.
- Dictionary: RCP Dictionary of mnemonics, MNERCP.
10 / 23 3BL 41292 DAAA REAGA Ed.01
RCPCFNET_1
APPENDIX A : CREBSC, DELBSC, INTBSC ANDMODBSC COMMAND PARAMETERSFor a list of the parameters to use in the CREBSC, DELBSC, INTBSC and MODBSC commands, seeTable 1.
The parameters in bold are mandatory.
Note : In screen mode, press:
- F1, to list the available parameters,
- Ctrl + F1, to list the parameter values.
Table 1 : CREBSC, DELBSC, INTBSC and MODBSC command parameters
Parameter Value Meaning
BSCNAM 1 to 8 alphanumeric characters BSC name
BSCDPC 0 to 16 383 or 0 to 16 777 215 depending on theaddress length used in the network
BSC destination pointcode
BSCNUM 0 to 99 (50 BSCs maximum) BSC number
BSCTYP Form value list: a, or a+b, or a+b+...+n (see Table2)
BSC type
NONE the BSC does not supportAMR (default value)
FR if the BSC is supported bythe UE, the AMR codecsare only used in full ratemode
HR if the BSC is supported bythe UE, the AMR codecsare only used in half ratemode
AMRRATE
BOTH the AMR codecs are usedin full and half rate mode
AMR channel rate
3BL 41292 DAAA REAGA Ed. 01 11 / 23
RCPCFNET_1
Parameter Value Meaning
FR when the two rates areused, the full rate is pre-ferred (default value)
HR when the two rates areused, the half rate is pre-ferred
AMRPRATE
MS when the two rates areused, the UE choice forthe rate and speech ver-sion remain unchanged
AMR preferred rate
Y the AMR handover is au-thorized when both ratesare used (default value)
AMRHO
N the AMR handover is notauthorized when bothrates are used
AMR handover
The BSCTYP parameter can use different specific values. For a list of the BSCTYP parameter values,see Table 2.
12 / 23 3BL 41292 DAAA REAGA Ed.01
RCPCFNET_1
Table 2 : BSCTYP Parameter values
BSCTYPvalues
Value attributes Meaning
CGI cell global identification
CI cell identity used to iden-tify the cells
LAC LAC (Location AreaCode) value used toidentify the cells insidea location zone
LACCI LAC and CI used to iden-tify the cells
LAI LAI (Location Area Iden-tity) used to identify allthe cells inside a locationzone (default value)
a
Note: If the option “all LAC/cells of the PLMN ac-cessible by all BSCs” is activated, only the LAI valueis authorized
Cell identification type
HORR message handling for“Handover Required Re-ject” messages (defaultvalue)
b
NOHORR no message handling for“Handover Required Re-ject”
“Handover” handling
CLMU handling for “Classmarkupdate” messages (de-fault value)
c
NCLMU no handling for “Class-mark update” messages
“Classmark update”handling
HOCI handling of the “Han-dover command” pa-rameter for the targetcell identification (de-fault value)
d
NHOCI no handling of the “Han-dover command” pa-rameter for the targetcell identification
“Handover command”handling
3BL 41292 DAAA REAGA Ed. 01 13 / 23
RCPCFNET_1
BSCTYPvalues
Value attributes Meaning
CONF handling of the “Con-fusion” message (defaultvalue)
e
NCONF no handling of the “Con-fusion” message
“Confusion” messagehandling
CIMEI handling of the “Cipher-ing mode command”with IMEI request (de-fault value)
f
NCIMEI no handling of the “Ci-phering mode com-mand” without IMEI re-quest
“Ciphering mode com-mand” message han-dling
IVTR handling of the MSC in-voke trace” message“(default value)
g
NIVTR no handling of the “MSCinvoke trace” message
“MSC Invoke trace” mes-sage handling
HCAUS handling of the “Han-dover request cause”message (default value)
h
NHCAUS no handling of the “Han-dover request cause”message
“Handover request”message handling
CLMI2 handling of the “Class-mark info 2” parameterof the “Assignment re-quest” message (defaultvalue)
i
NCLMI2 no handling of the“Classmark info 2” pa-rameter of the “Assign-ment request” message
“Assignment request”message handling
14 / 23 3BL 41292 DAAA REAGA Ed.01
RCPCFNET_1
BSCTYPvalues
Value attributes Meaning
UNEQ handling of the “Un-equipped circuit” mes-sage (default value)
j
NUNEQ no handling of the “Un-equipped circuit” mes-sage
“Unequipped circuit”message handling
FR full rate BSC version 1(default value)
DR full and half rate BSCversion 1 (this value ispossible only if option“half rate channel sim-plified management” isactivated)
FRMSV full and half rate BSCmulti-version speech(this value is possibleonly if option “multi-ver-sion speech” is activated)
k
DRMSV full and half ratemulti-version speechBSC (this value is possi-ble only if options, “halfrate channel simpli-fied management” and“multi-version speech”are activated)
Speech transcoder han-dling
CLMI3 “Handover request”message handling in the“Classmark info 3” pa-rameter (default value)
l
NCLMI3 no “Handover request”message“ handling with-out “Classmark info 3”parameter
“Classmark info 3” pa-rameter handling forthe “Handover request”message
3BL 41292 DAAA REAGA Ed. 01 15 / 23
RCPCFNET_1
BSCTYPvalues
Value attributes Meaning
CHAN “Channel needed” pa-rameter handling in thepaging message (defaultvalue)
m
NCHAN paging message han-dling without the “Chan-nel needed” parameter
Transmission of the“Channel needed” pa-rameter in the pagingmessage
LDIND “load indication” mes-sage handling
n
NLDIND no “load indication”message handling (de-fault value)
Transmission of the“Load indication” mes-sage
ICCH “Handover request”handling with “Currentchannel” parameter inthe message
o
NICCH “Handover request”handling without “Cur-rent channel” parameterin the message (defaultvalue)
Transmission of the“Current channel” pa-rameter in the “Han-dover request” message
TCM2 “Classmark 2” param-eter truncating in the“Handover request”message“ (default value)
p
NTCM2 no “Classmark 2” pa-rameter truncating inthe “Handover request”message“
4 octets truncating of the“Classmark 2” parame-ter in the “Handover re-quest” message
16 / 23 3BL 41292 DAAA REAGA Ed.01
RCPCFNET_1
BSCTYPvalues
Value attributes Meaning
DLDTX0 bit 1 of the “downlinkDTX” IE set to 0 (BSSauthorized by the MSCto activate DTX down-link) in the “Assignmentrequest” and “Handoverrequest” messages
q
DLDTX1 bit 1 of the “downlinkDTX” IE set to 1 (BSS notauthorised by the MSCto activate DTX down-link) on the “Assignmentrequest” and “Handoverrequest” messages (de-fault value)
bit 1 value of the “down-link DTX” IE in the “As-signment request” and“Handover request”messages
3BL 41292 DAAA REAGA Ed. 01 17 / 23
RCPCFNET_1
BSCTYPvalues
Value attributes Meaning
NIBSSI the “Old BSS to new BSSinformation” parameteris not included (defaultvalue)
r
IBSSI the “Old BSS to new BSSinformation” parameteris included
“Old BSS to new BSSinformation” parameterattached to the HO re-quest
PHASE 1 The BSCTYP values are predefined as:
- a = LAI
- b = HORR
- c = NCLMU
- d = NHOCI
- e = NCONF
- f = NCIMEI
- g = NIVTR
- h = NHCAUS
- i = NCLMI2
- j = NUNEQ
- k = FR
- l = NCLMI3
- m = NCHAN
- n = NLDIND
- o = NICCH
- p = TCM2
- q = DLDTX1
- r = NIBSSI
BSC Phase 1 predefinedvalues
18 / 23 3BL 41292 DAAA REAGA Ed.01
RCPCFNET_1
BSCTYPvalues
Value attributes Meaning
PHASE 2 The BSCTYP values are predefined as:
- a = LAI
- b = HORR
- c = CLMU
- d = HOCI
- e = CONF
- f = CIMEI
- g = IVTR
- h = HCAUS
- i = CLMI2
- j = UNEQ
- k = DR, FR, FRMSV or DRMSV
- l = NCLMI3
- m = CHAN
- n = LDIND
- o = ICCH
- p = NTCM2
- q = DLDTX1
- r = IBSSI
BSC Phase 2 predefinedvalues
3BL 41292 DAAA REAGA Ed. 01 19 / 23
RCPCFNET_1
APPENDIX B : CREREV, DELREV, INTREV AND MOD-REV COMMAND PARAMETERS
For a list of the parameters to use in the CREREV, DELREV, INTREV and MODREV commands, seeTable 3.
The parameters in bold are mandatory.
Note : In screen mode, press:
- F1, to list the available parameters,
- Ctrl + F1, to list the parameter values.
Table 3 : CREREV, DELREV, INTREV and MODREV command parameters
Parameter Value Meaning
LAC 1 to 65 533:
- 256 or 4 096 local LACs maximum per RCF, ac-cording to an option
If the option “Previous VLR determination using MSCidentity” is active, the LAC parameter must be onevalue from 0 to 63
Location area code
BSCNAM 1 to 8 alphanumeric characters BSC name
GAN de 1 to 127 Geographical areanumber
CELLID 0 to 65 535:
- 2 048 to 65 536 cells to the RCP maximum
- 512 or 65 536 cells to the BSC maximum
Cell identity
LOCNB a maximum of 15 digits ( E.164 format). The defaultvalue is the E.164 MSC address
Location address of thecell
NCGZ 1 to 128
By default, this value is initialized and depends onthe PLMN
Cell charging zone code
LATIT degre-mn-sec-hundredths of second-direction:
- degree = de 0 to 90
- minutes = 0 to 59
- seconds = 00 to 59
- hundredths of second= 00 to 99
- direction = N (north) or S (south)
Latitude of the center ofthe cell or of a set of cells
20 / 23 3BL 41292 DAAA REAGA Ed.01
RCPCFNET_1
Parameter Value Meaning
LONGIT degree-mn-sec-hundredths of second-direction:
- degree = 0 to 180
- minutes = 0 to 59
- seconds = 00 to 59
- hundredths = 00 to 99
- direction = E (east) or W (west)
Longitude of the centerof the cell or of a set ofcells
RADIUS 0 to 1 800 000 (meters)
The value 0 is only authorized in the command MOD-REV for deleting LATIT, LONGIT and RADIUS values
Radius of the cell or of aset of cells
LACSUP Y (yes) or N (no) Authorization of LACdeletion
3BL 41292 DAAA REAGA Ed. 01 21 / 23
RCPCFNET_1
APPENDIX C : CREAML, DELAML AND INTAML COM-MAND PARAMETERSFor a list of the parameters to use in the CREAML, DELAML and INTAML commands, see Table 4.
The parameters in bold are mandatory.
Note : In screen mode, press:
- F1, to list the available parameters,
- Ctrl + F1, to list the parameter values.
Table 4 : CREAML, DELAML and INTAML command parameters
Parameter Value Meaning
LAC 1 to 65 533:
- 128 or 1024 adjacent LACs maximum for theadjacent MSCs, depending on an option
If the option “Previous VLR determination using MSCidentity” is active, the LAC parameter must be onevalue from 0 to 63
Location area code
MSCNAM up to 8 alphanumeric characters Name of adjacent MSC
MSCGA 1 to 999 999 999 999 999 (maximum 15 digits), inthe international format
Global title of adjacentMSC
22 / 23 3BL 41292 DAAA REAGA Ed.01
RCPCFNET_1
APPENDIX D : CREAVL, DELAVL AND INTAVL COM-MAND PARAMETERSFor a list of the parameters to use in the CREAVL, DELAVL and INTAVLcommands, see Table 5.
The parameters in bold are mandatory.
Note : In screen mode, press:
- F1, to list the available parameters,
- Ctrl + F1, to list the parameter values.
Table 5 : CREAVL, DELAVL and INTAVL command parameters
Parameter Value Meaning
LAC 1 to 65 533:
- 128 or 1 024 adjacent LACs maximum for theadjacent VLRs, according to an option
If the option “Previous VLR determination using MSCidentity” is active, the LAC parameter must be onevalue from 0 to 63
Location Area Code
VLRDPC 0 to 16 383 or 0 to 16 777 215 depending on theaddress length used in the network
Destination point code ofthe adjacent VLR
VLRGA 1 to 999 999 999 999 999 (15 digits maximum) Global title of the adja-cent VLR
3BL 41292 DAAA REAGA Ed. 01 23 / 23