SPECIFICATIONSWingspan:.........................1630mm (63in.)Length:................................1070mm (41in.)Electric Motor:.....................See next pagerRTF Weight: 2.3Kg / 5.1lbs (Will vary withEquipment Used).Radio:....................6 Channel / 6 ServosFunction: Ailerons-Flaps-Elevator-Rudder

WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll andcause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen. Bei unsachgemässer Verwendung kannhoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe umprofessionelle Unterstätzung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells istdurch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

Radio control model / Flugmodell

ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY

Instruction manual / Montageanleitung

TECHNISCHE DATENSpannweite:...................................1630mmLange:............................................1070mmElektroantrieb.............(siehe nächste Seite)Brushless Motor:.............PULSAR P-15 X3Fluggewicht:.......................................2.3KgFernsteuerung................6 Kanal / 6 Servos

1.5mm

A B

!

CAL/R

Assemble left and right sides the same way. X

Drill holes using the stated

size of drill (in this case 1.5 mm )

Use epoxy glue

Take particular care hereHatched-in areas:remove covering film carefully

Not included.These parts must be

purchased separately

Check during assembly that theseparts move freely, without binding

Apply cyano glue

CA

GLUE

Cyanoacrylate Glue (thin type)

Minimum 6 channel radiowith 6 mini servos

# C5185 Servo MASTER S2112 ( x 2)

TOLLS REQUIREDHobby knife

Needle nose Pliers

Phillip screw driverAwl

ScissorsWire Cutters

(Purchase separately) Hex Wrench

..................................................................................................................

..................................................................................................................

..................................................................................................................

..................................................................................................................

..................................................................................................................

.........................................................

Sander

Masking tape - Straight Edged Ruler - Pen or pencil - Drill and Assorted Drill Bits

Read through the manual before you begin, so you will have an overall idea of what to do.

Symbols used throughout this instruction manual, comprise:

(Purchase separately)

.Elevator x1.Rudder x1. Aileron x2. R-L Flap x2

CONVERSION TABLE

1.0mm = 3/64”1.5mm = 1/16”2.0mm = 5/64”2.5mm = 3/32”

3.0mm = 1/8”4.0mm = 5/32”5.0mm = 13/64”6.0mm = 15/64”

10mm = 13/32”12mm = 15/32”15mm = 19/32”20mm = 51/64”

25mm = 1”30mm = 1-3/16”45mm = 1-51/64”

If exposed to direct sunlight and/or heat, wrinkels can appear. Storing themodel in a cool place will let the wrinkles disappear. Otherwise, removewrinkles in covering film with a hair dryer, starting withlow temperature. You can fix the corners by using a hot iron.

Bei Sonneneinstrahlung und/oder Wärme kann die Folie erschlaffen bzw. Faltenentstehen. Verwenden Sie ein Warumluftgebläse (Haartrockner) um evtl. Falten aus der Foliezu bekommen. Die Kanten können Sie mit einem Bügeleisen behandeln. Nicht zuviel Hitze anwenden !

Sonderzubehör (empfohlen) / Opional Accessories (recommended):

Low seting

# C6912Antriebsset 3-motorig für Junkers JU52inkl. 3 x Brushless Motoren, 3 x Brushless Regler,Kabelsätze

# 6745 LEMONRC LiPo Akku4300 - 11,1V

LEMONRC LiPo battery4300 - 11,1V

EPOXY A

EPOXY B

X3598-120

5-Min Epoxy

Power Set motors for Junkers JU 52incl. 3 Brushless Motors, 3 pcs. Brushless ESCand cable/wiring harness

# C6623 Servo MASTER S2112 / 4-Pack

Alle Infos zu diesem Zubehör unter:

www.pichler-modellbau.de

More infos about these Accessories:

X3572

Zoom CA

CA

Thin CA

Wing - top view

1Carefully, slide the motor mount into the slot onthe wing as shown. Ensuring that they are accuratelyaligned.

1A

1B

1D

CA

1.5mm

1.5mm

Plastic dummy engine

Fiber glass cowl

Vis 2x8mm

......10

1.5mm

2

2A

2B

2C

2D

Cut away only the covering

Cut away only the covering

Cut away only the covering

Cut away only the covering

CA

CALinkage Stopper set

..................1

6mm dowel.

...........2

Wing - bottom view

Vis 2x8mm

......4

1.5mm

3

4

Prop hub

3mm

Position the cowl so the distance from the prop hub to the plastic dummy engine is 3mm.

Aileron andFlap servo

3mm set Screw

2 mm

Aileron and Flap pushrod D=5/64”(2mm)

CA

CA

Thin CA

Thin CA

CA

CA

Thin CA

Thin CA

WINGFront-view

A A= 8-10mm

Wooden dowel

Wooden dowel

Wooden dowel

Cut away only the covering both side.

Full the elevator out of thehorizontal stabilizer.

The rectangular hole on the center of the stabilizer is pre-cut at factory

Cut away only the covering

Plastic control horn

.....................2

Linkage Stopper set..................2

175mm pushrod

......2

5

6

6A

6B

When you are satisfied with the alignment, use a pencil to trace around the top and bottom of the stabilizer where it meets the fuselage (7A).

Remove the horizontal stabilizer from the fuselage. Using the sharp hobby knife, carefully cut away the covering inside the lines which were marked above (7B).

* WARNING: When removing any covering from the airframe, please ensure that you secure the cut edge with CA or similar cement. This will ensure the covering remain tight.

Cut away only the coveringboth side

Note: the rectangular hole on the center of the stabilizer must be coincidental with the center line of the fuselage.

Install the horizontal stabilizer and the “U” torque rod into the fuselage at once, then adust the alignment as described in steep 7A. Secure the horizontal stabilizer in place using CA glue.

“U” torque rod

Drill the hole as marked, marking sure that you drillthe hole perpendicular to the leading edge ofthe elevator half (7E). Do the same way with second elevator.

Use the pencil, mark on the elevatorwhere the one end of “U” torque rod meets the elevator. Do the same way with the second elevator (7D).

3mm

77A

7B

7C

7D

7E

Vis 3x10mm

......2

Elevator control horn

...........1

Note: The rectangular hole for the control horn installation is pre- cut at factory.

Apply a thin layer of machine oil or petroleum jelly to only the top and bottom of the trailing edge of the elevator, then push the elevator and its hinges into the hinge slots in the trailing edge of the horizontal stabilizer. When satisfied with the and alignment, hinge the elevator to the horizontal stabilizer using CA glue.

Hinge

Petroleum jelly

STABILIZER

Thin CA glue

2mm

Test-fit one end of the “U” torque rod into each elevator half before glue the elevatorhinges to the horizontal stabilizer.

Cut away only the coveringboth side

Horn

Tail wheel mount

Fuselage Rudder

Gear

Side view

Hinge line

8 8A

8B

8C

CA

When you are satisfied with the alignment, use a pencil to trace around the right and left of the stabilizer where it meets the fuselage (9B).

Remove the horizontal stabilizer from the fuselage. Using the sharp hobby knife, carefully cut away the covering inside the lines which were marked above (9C).

* WARNING: When removing any covering from the airframe, please ensure that you secure the cut edge with CA or similar cement. This will ensure the covering remain tight.

99A

9B

9C

9D

Insert the vertical fin into the fuselage,ensuring that it is seated propertyon the horizontal stabilizer (9D).

9E

CA

Plastic dummy engine

Fiber glass cowl

1.5mm

Apply a thin layer of machine oil or petroleum jelly to only the top and bottom of the trailing edge of the rudder, then push the rudder and its hinges into the hinge slots in the trailing edge of the vertical stabilizer. When satisfied with the and alignment, hinge the rudder to the vertical stabilizer using CA glue.

Hinge

Petroleum jelly

STABILIZER

Thin CA glue

Vis 2x8mm

......4

10

11 11A

11B

11C

11D

3x12mm screw..............12

Nylon strap

..........6

Stopper (metal)

.............2

3mm set screw

Nylon strap

3x12mm screw

3mm set screw

Cut away only the covering

Note: All holes for landing gear installationare pre-drilled at factory

.............4

Note: All holes for landing gear installation are pre-drilled at factory

1212A

12CSlide the aluminum wing joinerinto the fuselage as shown.

30x4mm nylon bolt

............2

FUSELAGE - TOP VIEW

Secure the wing halves in placeusing two 30x4mm nylon bolts.

RIGHT WING HALVE

LEFT WING HALVE

4mm collar

3mm collar

.......1

.......1

13

14

Aluminum struts

4mm Main landing gear

2.5mm landinggear

Aluminum tube

Stopper (metal)

Collar

Collar

Stellring

Fahrwerksdraht

Hauptfahrwerk

4mm collar

3mm collar

Note: Use 4mm and 3mm collar to secure the aluminum struts only.

Not to screw here

CA

Cut away only thecovering both side.

3mm collar

4mm collar

154mm collar

16

4mm collar

.......1

CA

30x4mm nylon bolt

............2

Secure the top hatch in placeusing two 30x4mm bolts

Cut away onlythe covering

Elevator servo

Rudder servoElevator andRudder servo

3mm set Screw

2 mm

Elevator and rudder pushrod D=5/64”(2mm)

Linkage Stopper set..................2

Rudder control horn

...........1

175mm pushrod

......2

17

18

Ju-52 version Olympiade 1936 decalLufthansa decal

Note: Cut out the stickers and apply them in the proper area. Do not peel the backing paper off all at once. Peel off one corner of the backing and cut off with scissors. Arrange sticker on model and when satisfied adhere the corner without backing.Carefully peel back the rest of the backing while at the same time adhering the rest of the sticker.

Try not to make air bubbles, if there are some, carefully puncture sticker (center of bubble) but not model surface with the tip of the knife or sharp pin and squeeze out the air.

Cut around the cycles

Wing center section

DO NOT try to fly an out-of-balance model !

Note: If necessary, move the battery pack or add weight to either the tail or nose until the correct balance is achieved.

10mm Up

25 mm

RUDDER 6mm

AILERON

IMPORTANT: Flying your model at these throws will provide you with the greatest chance for successful first flights. If,after you have become accustomed to the way the Ju-52 flies, you would like to change the throws to suit your taste that is fine. However, too much control throw could make the model difficult to control, so remember, “more is not always better”.

ELEVATOR

20mm

FLAP

88~94mm

IMPORTANT: Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner to clean on surface of your model to keep the colour not fade.

BALANCE - CONTROL SURFACE

6mm

25 mm

8mm Down

19

20

Decal for recover

Page 1Page 2Page 3Page 4Page 5Page 6Page 7Page 8Page 9Page 10Page 11Page 12Page 13Page 14Page 15