quilted in honor - vw-islandbatik.storage.googleapis.com · designer: doug leko dawn’s early...
TRANSCRIPT
Designer: Doug Leko Dawn’s Early Light Antler Quilt Design 59” x 71”(763) 516-3855 www.antlerquiltdesign.com
Dawn’s Early LightDoug Leko’s
© 2013 Antler Quilt Design Dawn’s Early Light - Free Pattern for Quilted in Honor Page 1
5” square Make 4
Fabric Cut Sub-cut Label Red - 1-1/4yds (KP02-6US) 9, 2” WOF strips Save for strip piecing R1
1, 2” WOF strip 4, 5” x 2” rectangles R2
3, 3-1/2” WOF strips Save for strip piecing R3
2, 5” WOF strips 10, 5” squares R4
1,7-3/4” WOF strip 2, 7-3/4” square R5
White - 1-1/4yds (US02-3) 12, 2” WOF strips Save for strip piecing W1
2, 5” WOF strips 14, 5” squares W2
Blue - 1-2/3yds (US02-1)
1, 4-5/8” WOF strip 8, 4-5/8” squares B1
3, 7-3/4” WOF strips 12, 7-3/4” squares B2
1, 26” WOF strip 1, 38-5/8” x 26” rectangle Center
Outer Border - Blue - 1-1/4yds (US02-1) 8, 5” WOF strips none none
Binding - Blue - 1/2yd (US02-1) 7, 2-1/4” WOF strips none none
Proof: Measure HST: Half square triangle
: Cut corner-to-corner once : Cut corner-to-corner twice
Tip: Label components after you cut sub-cut to organize.
Cutting Instructions: Seam Allowance: 1/4” HWOF: Half Width of fabric WOF: Width of fabric RST: Right sides together
Please read ALL THE INSTRUCTIONS thoroughly before you start cutting and sewing.
Dawn’s Early Light Lap: 59” x 71”
Sub-cut into 2” Segments
Need 60 Segments
Step 1A. W1W1W1W1
2. Block Assembly's What you’ll need:
Step 1A Units: 60 segments Step 1B Units: 56 segments Step 1C Units: 48 segments R2: 4, 5” x 2” rectangles
Take cut segments from Step 1A, 1B, and 1C and assemble each unit as diagramed. Press as shown. Proof each block to 5” square.
Step 1B.
5” square Make 4
W1W1W1W1
R1R1R1R1 cv
Sub-cut into 2” Segments
Need 56 Segments
R1R1R1R1
R1R1R1R1
W1W1W1W1
Sub-cut into 2” Segments
Need 48 Segments
W1W1W1W1
R3R3R3R3
Step 1C.
5” square Make 48
Step 2.
1. Strip Piecing Units What you’ll need:
R1: 9 strips R3: 3 strips W1: 10 strips
A. Take two strips of W1 and one strip of R1 and assemble strip set as shown. Make 3 strip sets. Press as shown. Sub-cut into 2” segments. Make 60.
B. Take two strips of R1 and one strip of W1 and assemble strip set as shown. Make 3 strip sets. Press as shown. Sub-cut into 2” segments. Make 56.
C. Take one strip of R3 and one strip of W1 and assemble strip set as shown. Make 3 strip sets. Press as shown. Sub-cut into 2” segments. Make 48.
Make 3 Strip Sets
Make 3 Strip Sets
Make 3 Strip Sets
© 2013 Antler Quilt Design Dawn’s Early Light - Free Pattern for Quilted in Honor Page 2
What you’ll need:
R4: 10, 5” squares R5: 8, 7-3/4” triangles W2: 14, 5” squares B1: 16: 4-5/8” triangles B2: 48, 7-3/4” triangles
Assemble both units as diagramed. Press seams as shown. Proof size of units to shown size for each. Make 2 of each Pieced Unit.
3. Pieced Unit’s Assembly
51-1/2”
Make 2
63-1/2” x 76-1/2”
Make 2
B2B2B2B2 B1
R5R5R5R5
B1B1B1B1
W2W2W2W2 R4R4R4R4
B2B2B2B2 B1B1B1B1
R5R5R5R5 W2W2W2W2 R4R4R4R4
0
0 0
0
0
0
What you’ll need:
Appliqued Center Four Pieced Units from Step 3 Eight Outer Border Strips
Assemble quilt as diagramed. Press seams as shown.
4. Quilt Assembly
38-5/8”
13-1/4
”
13-1/4
”