pumps macerators and aerators - range guide. water management… · 2019. 10. 21. · online...

WILO UK LimitedCentrum 100, Second Avenue

Burton on Trent, Staffs DE14 2WJT +44 (0) 1283 523000F +44 (0) 1283 523099

[email protected]

Wilo IrelandUnit B1, Corcanree Business Park

Dock Road, Limerick, IrelandT: +353 (0)61 227566F: +353 (0)61 229017

[email protected]

“I plan with Wilo because they know about the future.”

Range Guide.Water Management.

World Leading.WILO SE, with headquarters in Dortmund, is one of the world’s leading manufacturers of pumps and pump systems for heating, air conditioning and cooling technology, as well as for water supplies and sewage treatment and disposal.

Food & Bev Quarry & Mining Utilities Power &

Generation Manufacturing Pharma

Booster Set’s

¸¸¸ ¸¸ ¸¸¸ ¸¸¸ ¸¸¸ ¸¸

Submersible

¸ ¸¸¸ ¸¸¸ ¸¸ ¸ ˚

Borehole

¸ ¸¸¸ ¸¸¸ ¸ ¸ ˚

Split Case

¸ ¸¸¸ ¸ ¸¸¸ ¸ ¸

End Suction

¸¸ ¸¸¸ ¸ ¸¸¸ ¸¸¸ ¸¸¸

Mixers

˚ ¸¸ ¸¸¸ ¸ ˚ ˚

Vertical Turbine

˚ ¸¸ ¸¸¸ ¸¸¸ ˚ ˚

In-Line

¸¸¸ ¸¸ ¸¸ ¸¸ ¸¸¸ ¸¸¸

Vertical Multistage

¸¸¸ ¸¸ ¸¸ ¸¸¸ ¸¸¸ ¸¸¸

¸¸¸ : Extensive Use ¸¸ : Regular Use ¸ : In'Fequent Use ˚ : Very Rare

Application Analysis

High competence for water and sewage.

Clean water is becoming increasingly scarce. This makes the sourcing and transportation of valuable water a ceaseless challenge. In view of the variety of sources, e.g. desalinated seawater or aquifers, treatment systems must be more flexible to meet the different compositions of the water. Pumps and components from Wilo are able to supply the fluid for as efficiently and for as long as possible in the best possible way.

When it comes to environmental protection and preserving natural resources, sewage disposal and sewage treatment play an important part. Ongoing challenges such as the increasing content of solid in sewage which makes operating conditions for plants and equipment more difficult create a need for innovative approaches.

Wilo offers the right solution for any application: with the highest safety standards and lowest cost.

3

Founded in 1872 as Kupfer- und Messingwarenfabrik Louis Opländer, the company has almost 70 branches worldwide and over 6,200 employees Turnover amounted to 1,021.4 million EUR in 2010. International recognition has increased rapidly since the company became a European limited liability company (SE) in 2008. Wilo pumps and systems set global standards for efficiency and technical performance: with high-efficiency solutions for all applications in the segments.

Submersible mixerSeriesWilo-EMU TR 22 to TR 40

Submersible mixerSeriesWilo-EMU TR 50-2 to TR 90-2Wilo-EMU TRE 90-2 with IE3 motor

Submersible mixerSeriesWilo-EMU TR 212 to TR 226Wilo-EMU TR 316 to TR 326Wilo-EMU TRE with IE3 motor

Recirculation pumpSeriesWilo-EMU RZP 20 to RZP 80-2

Design Compact directly driven submersibleMixer

Q max. Thrust: 185 - 1100 N

Special features • Self-cleaning propeller with helix hub• Easy-to-install propeller attachment• Propeller in steel or PUR version• ATEX and FM versions

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Protection class: IP 68• Max. fluid temperature: 40 °C• Mechanical seal with SiC/SiC combination• Permanently lubricated anti-friction

bearing• Max. immersion depth: 20 m

Equipment/function• Stationary installation on walls and floors• Flexible installation through the use of

lowering device• Can be swivelled vertically and

horizontally for installation with lowering device

InformationOnline catalogue www.wilo.comCatalogue Water ManagementDrainage and sewage

Design Submersible mixer with single-stageplanetary gear


Special features• Single-stage planetary gear for adjusting

the propeller speed• Self-cleaning propeller• Easy-to-install propeller attachment• Propeller in steel, PUR or PUR/GFK version• ATEX and FM versions• 1.4462 gear shaft• Type “TRE” with IE3 performance

optimised motors (derived from IEC 60034-30)

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Protection class: IP 68• Max. fluid temperature: 40 °C• Single-stage planetary gear• Mechanical seal with SiC/SiC combination• Permanently lubricated anti-friction


Equipment/function• Stationary installation on walls• Flexible installation through the use of

lowering device• Can be swivelled horizontally for

installation with lowering device• Installation with stand allows free

placement in basin• Single-stage planetary gear


Design Slow-running submersible mixer withtwo-stage planetary gear


Special features• 2-stage planetary gear for adjusting the

propeller speed• Self-cleaning propeller• Propeller blades can be replaced

individually• Easy-to-install blades and hub• Propeller in GFK version• ATEX and FM versions• 1.4462 gear shaft• “TRE” type with high performance

motors according to IE3 (derived from IEC 60034-30)

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Protection class: IP 68• Max. fluid temperature: 40 °C• Two-stage planetary gear with

exchangeable second planetary stage• Mechanical seal with SiC/SiC combination• Permanently lubricated anti-friction


Equipment/function• Installation with stand allows free

placement in basin• Flexible installation• Two-stage planetary gear with

exchangeable second planetary stage


DesignSubmersible mixers with housing unit,direct driven (RZP 20 …, RZP 25-2 … RZP40...) or with 1-stage planetary gear(RZP 50-3 …, RZP 60-3 …, RZP 80-2 …)

Q max.6,800 m³/h

H max.1.1 m

Special features• Submersible• Vertical or in-line design• Self-cleaning propeller, partially with

helix hub• Propeller in steel or PUR version• ATEX and FM versions

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Protection class: IP 68• Max. fluid temperature: 40 °C• Units are directly driven or with

singlestage planetary gear• Mechanical seal with SiC/SiC combination• Permanently lubricated anti-friction


Equipment/function• Stationary installation directly on flow pipe

• Flexible installation through the use of lowering device

• Vertical or in-line installation possible


Product category Product category Product category Product category

13

Design Glandless circulation pump with threaded connection, EC motor and automatic power adjustment.

Q max. 4 m³/h

H max. 6.0 m

Special features • Energy efficiency class A• High-efficiency pump especially for single

and two-family houses, as well as for two to six-family houses.

• Up to 90 % electricity savings compared to old uncontrolled heating pumps

• Only 3 watts min. power consumption• Very high starting torque for reliable

starting• Integrated motor protection• Venting routine for automatic venting

of the rotor chamber

Technical data• Fluid temperature +2 °C to +110 °C• Mains connection 1~230 V, 50 Hz• Protection class IP X4D• Threaded connection Rp ½, Rp 1 and Rp

1¼• Max. operating pressure 10 bar

Equipment/function • Control mode: Δp-c and Δp-v, Dynamic

Adapt control function combinied with Δp-v

• Automatic setback operation• Automatic venting routine• Automatic deblocking function• Red-button technology for simple

operation• Display indication of current power

consumption in W and accumulated electricity consumption in kWh

• Reset function for resetting the electricity meter

• Reset function for resetting to the factory settings

• Blocking current-proof motor• Particle filter• Quick electrical connection with Wilo-

Connector• Options: - Design with bronze pump housing for

use in underfloor heating systems, - Versions with short port-to-port length

130 mm

InformationOnline catalogue www.wilo.comBuilding Services catalogue, Heating,Air-Conditioning, Cooling

Design High-efficiency inline pump with EC motor and electronic duty adaptation in glanded construction. Version as singlestage low-pressure centrifugal pump with flange connection and mechanical shaft seal.

Q max. 44 m³/h

H max. 52 m

Special features• Innovative high-efficiency pump for

the highest overall degrees of efficiency based on a new Wilo glanded design

• High-efficiency EC motor (degrees of efficiency above IE4 limit values acc. to IEC TS 60034-31 Ed.1)

• New hydraulics optimally adapted to the EC motor technology

• Integrated electronic power adjustment• Extremely compact and space-saving

design• Simple operation by tried-and-tested

red-button technology and display• Various control modes Δp-c, Δp-v, PID

and n-const. (control mode)• Control range up to three times greater

than in conventional electronically controlled pumps

• Analogue interfaces 0-10 V, 2-10 V, 0-20 mA, 4-20 mA

• Optional interfaces for bus communication using plug-in IF-Modules

• Integrated dual-pump management with efficiency-optimised peak-load cut-in

Technical data • Permitted temperature range of the fluid

-20 °C to +140 °C• Mains connection:

3~440 V (±10 %), 50 Hz/60 Hz 3~400 V (±10 %), 50 Hz/60 Hz 3~380 V (-5 %/+10 %), 50 Hz/60 Hz

• Protection class IP 55• Max. operating pressure 16 bar to +120

°C, 13 bar to +140 °C

Equipment/functionSingle-stage, low-pressure centrifugal pump in in-line design with• Mechanical seal• Flange connection• Lantern• Coupling• EC motor with electronic power

adjustment

Materials:• Pump housing and lantern: EN-GJL-250• Impeller: PPS-GF40• Shaft: 1.4122• Mechanical seal: AQ1EGG Other

mechanical seals: on request

InformationOnline catalogue www.wilo.comBuilding Services catalogue, Heating,Air- Conditioning, CoolingWe are continually adding to this series.

Design Electronically controlled glanded pump in in-line design with flange connection and automatic power adjustment

Q max. 170 m³/h

H max. 30 m

Special features • Motors with higher efficiency as standard;

from 0.75 kW nominal motor power motors with IE2 technology

• Energy savings due to integrated electronic power control

• Simple operation with red-button technology and display

• Various control modes Δp-c, Δp-v, PID and n-const. (control mode)



• Integrated dual pump management• Integrated full motor protection (PTC

thermistor sensor) with trip electronics

Technical data • Permissible temperature range -20 °C to

+120 °C• Mains connection:

3~400 V, 50 Hz; 3~380 V, 60 Hz

• Protection class IP 55• Nominal diameter DN 32 to DN 80• Max. operating pressure 10 bar (special

version: 16 bar)

Equipment/function Single-stage, low-pressure centrifugal pump in in-line design with• Mechanical seal• Flange connection• Motor with integrated electronic speed

control• DP-E with switchover valve

Materials:• Pump housing and lantern: EN-GJL-250• Impeller: PPO-GF30• Shaft: 1.4021• Mechanical seal: AQEGG Other mechanical seals: on request

Information Online catalogue www.wilo.com Building Services catalogue, Heating, Air-Conditioning, Cooling


Q max. 680 m³/h

H max. 65 m

Special features • Motors with IE2 technology for higher

efficiency fitted as standard• Energy savings due to integrated

electronic power control• Simple operation with red-button

technology and display• Various control modes Δp-c, Δp-v, PID

and n-const. (control mode)• Analogue interfaces 0-10 V, 2-10 V, 0-20

mA, 4-20 mA• Optional interfaces for bus

communication using plug-in IF-Modules• Integrated dual pump management• Integrated full motor protection (PTC




3~400 V, 50 Hz; 3~380 V, 60 Hz

• Protection class IP 55• Nominal diameter DN 40 to DN 80• Max. operating pressure 16 bar

Equipment/functionSingle-stage, low-pressure centrifugalpump in in-line design with• Mechanical seal• Flange connection• Lantern• Coupling• Engine with integrated electronic power

adjustment• DL-E with switchover valve

Materials:• Pump housing and lantern: EN-GJL-250• Impeller: Standard version: EN-GJL-200 special version: G-CuSn 10• Shaft: 1.4122• Mechanical seal: AQEGG Other mechanical seals: on request



Glandless Premium high-efficiencypumpsSeriesWilo-Stratos PICO

Glanded high-efficiency pumps inin-line designSeriesWilo-Stratos GIGA

Glanded energy-saving pumps inin-line designSeriesWilo-VeroLine-IP-EWilo-VeroTwin-DP-E

Glanded energy-saving pumps inin-line designSeriesWilo-CronoLine-IL-EWilo-CronoTwin-DL-E

Product category

Design Submersible bottom intake pump

Q max. 1,200 m³/h

H max. 160 m

Special features• Deep water lowering• Self-cooling design• Easy installation on the ascending pipe• Wear-resistant design due to different

material versions• Compact design• Rewindable motors• Individual adjustment to duty point due

to impeller correction• Ceram CT coating possible to increase

Effectiveness

Technical data• Mains connection: 3~400 V, 50 Hz• Max. fluid temperature: 20 °C• Min. flow at outside shroud: not necessary• Max. sand content: 35 g/m³• Up to 10 starts per hour• Max. immersion depth: 300 m• Protection class: IP 68• Control range for frequency converter:

--2-pole: 25-50 Hz --4-pole: 30-50 Hz

Equipment/function• Immersible, multistage submersible pump• Semi-axial impellers• Hydraulics and motor freely configurable

according to power requirements• Three-phase motor for direct or stardelta

start.• Motors rewindable as standard

InformationOnline catalogue www.wilo.comCatalogue Water ManagementWater supply

Design Dry installed vertical turbine pumps with immersed axial- or semi-axial hydraulics

Q max. 40,000 m³/h

H max. 450 m

Special features• Minimum surface area needed• High hydraulic efficiency• immersed pump hydraulics• Design to order as per customer

Specifications

Technical data• Perm. temperature range to 80 °C 105 °C• Nominal diameter DN 100 to DN 2000

Equipment/functionFor installation types with pressure portsfor underground, above-ground or twinroofinstallation• Design

-- as removable or permanent installation

-- with axial or semi-axial, single or multistage hydraulics

-- with open shaft for bearing lubrication with the fluid or with shaft trim for separate bearing lubrication

• Drive options: Electric motor, Diesel motor or steam turbine

InformationDocumentation on request

Design Axial submersible pump with dry motor for use in pipe sumps

Q max. 9,500 m³/h

H max. 8.4 m

Special features• Special materials and coatings against

abrasion and corrosion• Longitudinally watertight cable lead-in• Angle of propeller blades adjustable by

hand

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Protection class: IP 68• Max. fluid temperature: 40 °C, higher

temperatures on request• Sealing with two mechanical seals or one

block seal cartridge, depending on motor• Free ball passage of 85 to 130 mm• Short common pump/motor shaft• Permanently lubricated anti-friction


Equipment/function• Heavy-duty version made of cast iron

InformationOnline catalogue www.wilo.comCatalogue Water Management

Design Compact directly driven submersible Mixer


Special features • Low power consumption• Low weight• ATEX and FM versions• Self-cleaning propeller with helix hub• Easy-to-install propeller attachment• Propeller in steel or PUR version• Optional: Motor shaft made of 1.4462

material

Technical data • Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Protection class: IP 68• Max. fluid temperature: 40 °C• Mechanical seal with SiC/SiC combination• Permanently lubricated anti-friction


Equipment/function• Stationary installation on walls and floors• Flexible installation through the use

of lowering device or special pipe attachment

• Can be swivelled vertically and horizontally for installation with lowering device



Submersible pumpsSeriesWilo-EMU bottom intake pumps

Vertical turbine pumpsSeriesSeries VMF, CNE, VAF

Submersible sewage pumpsSeriesWilo-EMU KPR …


Glanded standard pumps inin-line designSeriesWilo-VeroLine-IPLWilo-VeroTwin-DPL

Glanded standard pumps inin-line designSeriesWilo-CronoLine-ILWilo-CronoTwin-DL

Special glanded pumps in in-line designSeriesWilo-VeroLine-IPH-WWilo-VeroLine-IPH-O

Special glanded pumps in in-line designSeriesWilo-VeroLine-IPS

Design Glanded pump in in-line design with threaded connection or flange connection

Q max. 245 m³/h

H max. 52 m



• Standard condensate drainage holes in the motor housings and lanterns

• Series version: Motor with one-piece shaft

• Version N: Standard motor B5 or V1 with stainless steel plug shaft

• Bidirectional mechanical seal with forced flushing

• Easy to install due to feet with threaded holes on pump housing

Technical data• Perm. temperature range -20 °C to

+120 °C• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameter Rp 1 to DN 100• Max. operating pressure 10 bar

(special version: 16 bar)

Equipment/function Single-stage, low-pressure centrifugal pump in in-line design with• Mechanical seal• For flange connection with pressure

measuring connection R ½• Motor with one-piece shaft• DPL with switchover valve

Materials: • Pump housing and lantern: EN-GJL-250• Impeller: PPO fibreglass-reinforced

EN-GJL-200 (depending on pump type)• Shaft: 1.4021• Mechanical seal: AQEGG; other

mechanical seals on request

InformationOnline catalogue www.wilo.com Building Services catalogue, Heating, Air-Conditioning, Cooling

Design Glanded pump in in-line design with flange connection

Q max. 1,150 m³/h

H max. 110 m



• Reduced life cycle costs due to optimised efficiency

• Standard condensate drainage holes in the motor housings

• Can be used flexibly in air-conditioning and cooling systems, with application benefits due direct draining of condensate via optimised lantern design (patented)


• High worldwide availability of standard motors (according to Wilo specifications) and standard mechanical seals


Technical data• Perm. temperature range -20 °C

to+140 °C• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameter DN 32 to DN 250• Max. operating pressure 16 bar (25 bar on request)

Equipment/functionSingle-stage, low-pressure centrifugal pump in in-line design with• Mechanical seal• Flange connection with pressure

measuring connection R ½• Lantern• Coupling• IEC standard motor• DL with switchover valve

Materials: • Pump housing and lantern:

Standard version: EN-GJL-250Optional: Spheroidal cast iron EN-GJS-400-18-LT• Impeller:

Standard: EN-GJL200Special version: Red brass G-CuSn 10 • Shaft: 1.4122• Mechanical seal: AQEGGOther mechanical seals: on request



Q max. 80 m³/h

H max. 38 m

Special features • From 0.75 kW nominal motor power

motors with IE2 technology for higher efficiency fitted as standard

• Bidirectional, self-cooled mechanical seal• Great variety of applications by a

large fluid temperature range without additional wearing parts

Technical data• Permissible temperature range IPH-W:

-10 °C to +210 °C (at a max. of 23 bar)• Permissible temperature range IPH-O:

-10 °C to +350 °C (at a max. 9 bar)• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameter DN 20 to DN 80

Equipment/function Single-stage, low-pressure centrifugal pump in in-line design with• Mechanical seal• Flange connection• Lantern• Motor with special shaft

Information Online catalogue www.wilo.com


Q max. 13 m³/h

H max. 3 m

Special features • Worldwide availability of the standard

motors used

Technical data • Perm. temperature range -10 °C

to+140 °C• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameter Rp 1, DN 40 and DN 50• Max. operating pressure 10 bar or 6 bar

for flange connection

Equipment/function Single-stage, low-pressure centrifugal pump in in-line design with• Mechanical seal or stuffing box• Threaded or flange connection with

pressure measuring connection R ⅛• Standard motor

Materials: • Pump housing and lantern: EN-GJL-200• Impeller: Plastic• Shaft: 1.4021• Mechanical seal: BVEGGOther mechanical seals on request



5

Standard glanded pumpsSeriesWilo-CronoNorm-NLWilo-VeroNorm-NPG

Axially split case pumpsSeriesWilo-SCP

Submersible pumpsSeriesWilo-Sub TWI 4 …Wilo-Sub TWI 6 …Wilo-Sub TWI 8 …Wilo-Sub TWI 10 …

Submersible pumpsSeriesWilo-EMU 6” seriesWilo-EMU 8” seriesWilo-EMU 10”…24” series

Design Single-stage low-pressure centrifugal pump with axial suction, in accordance with EN 733 and ISO 5199, mounted on baseplate.

Q max. 3,000 m³/h

H max. 140 m

Special features• Motors with higher efficiency as standard;


• Other materials and versions on request


+140 °C• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameter on suction side DN 50

to DN 500• Nominal diameter on pressure side DN 32

to DN 500• Maximum operating pressure: depending

on type and application up to 16 bar

Equipment/functionSingle-stage low-pressure centrifugal pump in monobloc design with coupling, coupling protection, motor and baseplate• Mechanical seal or stuffing box• Wilo factory motor or ATB motor

Materials:• Pump housing: EN-GJL-250• Impeller: EN-GJL-250• Shaft: 1.4028

InformationOnline catalogue www.wilo.com

DesignLow-pressure centrifugal pump with axially split housing mounted on a Baseplate

Q max. 3,400 m³/h

H max. 245 m

Special features• Higher capacities up to 17,000 m³/h on

request• Special motors and other materials on

Request




to DN 400• Max. operating pressure: depending on

type 16 or 25 bar

Equipment/function1- or 2-stage, low-pressure centrifugal pump in monobloc design• Delivered as complete unit (pump with

coupling, coupling protection, motor and baseplate) or without motor or only pump hydraulics

• Shaft seal with mechanical seal or stuffing box

• 4-pole and 6-pole motors

Materials:• Pump housing: EN-GJL-250• Impeller: GCuSn5 ZnPb• Shaft: X12Cr13


DesignSubmersible pump, multistage

Q max.165 m³/h

H max.500 m

Special features• Unit made completely of stainless steel• Integrated non-return valve• Vertical and horizontal installation

possible• Standard and configurable versions

available (TWI 6 … / TWI 8 … / TWI 10...)• Star-delta version• Rewindable motors

Technical data• Mains connection: 1~230 V, 50 Hz (only

TWI 4 …) or 3~400 V, 50 Hz• Immersed operating mode: S1• Fluid temperature: 3-20 °C or 3-30 °C• Min. flow at motor: 0.08-0.5 m/s• Max. sand content: 50 g/m³• Up to 10 or 20 starts per hour• Max. immersion depth: 100-350 m• Protection class: IP 68

Equipment/function• Multistage submersible pump with radial

or semi-axial impellers• Integrated non-return valve• NEMA coupling• AC-(only TWI 4) or three phase motor• Hermetically sealed or rewindable (TWI 6

… / TWI 8 … / TWI 10...) motors


Design Submersible pump with sectional Construction

Q max. 2,400 m³/h

H max. 560 m

Special features• Water pumping with large volume flows• Corrosion-resistant impellers• Wear-resistant GI bushing (depending on

type)• Special materials possible• Individual adjustment to duty point due

to impeller correction• 4-pole motors for long service life and

high degree of efficiency• Motors with CoolAct technology for high

power density (from 10” motors on)• High voltage up to 6000 V possible• Vertical and horizontal installation

possible• Ceram CT coating possible to increase

effectiveness• Pressure shroud installation option

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Max. fluid temperature: 20...30 °C• Min. flow at motor: 0.1 ... 0.5 m/s• Max. sand content: 35 g/m³• Up to 10 starts per hour• Max. immersion depth: 100 or 300/350 %• Protection class: IP 68• Control range for frequency converter:

25...50 or 30...50 Hz

Equipment/function• Immersible, multistage submersible pump• Radial or semi-axial impellers• Hydraulics and motor freely configurable

according to power requirements• Integrated non-return valve (depending

on type)• NEMA coupling or standardised

connection (from 10” motors on)• Three-phase motor for direct or stardelta

start.



11

Design Glanded pump in monobloc design with flange connection

Q max. 360 m³/h

H max. 105 m



• Meets user requirements due to performance and main dimensions in accordance with EN 733

• Long motor life due to standard condensate drainage holes in the motor housing

• Corrosion protection due to cataphoretic coating


to +140 °C• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameter DN 32 to DN 150• Max. operating pressure 16 bar

(25 bar on request)

Equipment/function Single-stage low-pressure centrifugal pump in block design, with axial suction port and radially arranged pressure port with• Mechanical seal• Flange connection with pressure

measuring connection R ⅛• Lantern• Coupling• IEC standard motor

Materials: • Pump housing standard: EN-GJL-250Optional: EN-GJS-400-18• Impeller (standard): EN-GJL-200Special version: Bronze G-CuSn10• Shaft: 1.4122• Mechanical seal: AQEGGOther mechanical seals on request


Design Glanded pump in monobloc design with threaded connection or Victaulic Connection

Q max. 80 m³/h

H max. 25 m




• Pump housing in plastic design• Version with Victaulic or threaded

connection (BAC 70/135... with Victaulic connection only)

Technical data • Perm. temperature range -15 °C to

+60 °C• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameter G2/G 1½

(only BAC 40… /S) or Victaulic connection ∅ 60.3/48.3 mm (BAC 40… /R) ∅ 76.1/76.1 mm (BAC 70…/R)• Max. operating pressure 6.5 bar

Equipment/function Single-stage low-pressure centrifugalpump in monobloc design, with axialsuction port and radially arrangedpressure port

Materials: • Pump housing: PA 6.6 50 % GF• Impeller: PA/PPO, fibreglass-reinforced• Shaft: X30Cr13• Mechanical seal: BQEGG


Design Automatic rainwater utilisation system with run-down tank container and 2 non self-priming pumps

Q max. 16 m³/h

H max. 56 m

Special features • Low-noise due to multistage centrifugal

pumps• All parts that come in contact with the fluid are corrosion-free

• Maximum operational reliability, due to trendsetting fully electronic RainControl Hybrid controller

• High economic efficiency due to fresh water replenishment according to requirements

• High reliability, due to flow- and noiseoptimised overall concept

• Automatic control of the feeding pump• System/level control in the low-voltage

Range

Technical data • Mains connection 3~400 V, 50 Hz• Fluid temperature max. +5 °C to +35 °C• Operating pressure max. 10 bar• Replenishment reservoir 400 l• Protection class IP 54

Equipment/function • Connection-ready module with compact

construction• Fully connected electrically and

hydraulically• Mounted on vibration-insulated

baseplate• 2 MultiPress MP centrifugal pumps

(non-self-priming)• Joint tubing R 1½” on the pressure side,

inc. transmitter unit, diaphragm pressure vessel, shut-off device

• Pressure gauge 0-10 bar• Ball valve on suction and pressure sides

and non-return valve• High-volume hybrid tank with all

connections, calmed inlets and overflow with siphon

• RainControl Hybrid central switchgear with control electronics

• Signals concerning operation and faults• Cyclical pump cycling and test run when

pump at rest• Automatic fault-actuated switchover and

peak-load cut-in• Automatic water exchange in the

replenishment reservoir• Permanent display of rainwater storage

tank level, system pressure, operating status (optional)

Information Online catalogue www.wilo.com Building Services catalogue, Water Supply

Design Self-priming multistage centrifugal Pumps

Q max. 7 m³/h

H max. 57 m

Special features • Low-noise• Ideal as a base-load pump for rainwater

utilisation• HMC version with diaphragm pressure

vessel and pressure switch• FMC version with fluid control for system

control

Technical data • Mains connection 1~230 V, 50 Hz 3~400

V, 50 Hz• Inlet pressure max. 4 bar• Fluid temperature max. +5 °C to +35 °C• Ambient temperature max. +40 °C• Operating pressure max. 8 bar• Protection class IP 54• Suction/pressure side connections: -MC (Rp 1/Rp 1) -FMC (R 1/Rp 1) -HMC (Rp 1/Rp 1)

Equipment/function • Directly flanged motor• Thermal motor protection switch for

single-phase AC motor (1~230 V



Glanded monobloc pumpsSeriesWilo-CronoBloc-BL

Glanded monobloc pumpsSeriesWilo-BAC

Rainwater utilisation systemsSeriesWilo-RainSystem AF 400

Self-priming multistage pumps andpump systemsSeriesWilo-MultiCargo MCWilo-MultiCargo HMCWilo-MultiCargo FMC

Design Submersible sewage pumps

Q max. 380 m³/h

H max. 51 m

Special features• Operation in stationary and portable wet

well installation• Heavy-duty version made of cast iron• Easy installation due to suspension unit

or pump base• Longitudinally watertight cable lead-in• ATEX approval

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Surfaced operating mode: S2-15 or

S2-30 (depending on type)• Thermal motor monitoring• Protection class: IP 68• Insulation class: F• Max. fluid temperature: 40 °C• Free ball passage of 45 to 100 mm• Permanently lubricated anti-friction


Equipment/function• Heavy-duty version made of cast iron• Simple installation via suspension unit or

pump base

InformationOnline catalogue www.wilo.comBuilding Services catalogue,Drainage and Sewage

DesignSubmersible sewage pump for industrial Applications

Q max. 180 m³/h

H max. 21 m

Special features• Stainless steel & composite• ATEX approval (not for model “AM”)• Low weight• Detachable connection cable• Standard-equipped with cooling jacket• Corrosion-resistant (e.g. swimming pool

water, salt water, etc.)

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Surfaced operating mode: S1• Protection class: IP 68• Insulation class: F• Thermal winding monitoring• Sealing chamber control• Max. fluid temperature: 40 °C• Free ball passage: 80 or 100 mm• Max. immersion depth: 20 m

Equipment/function• Thermal motor monitoring• Sealing chamber monitoring• ATEX approval (not for model “AM”)• Sheath current cooling• Model “AM” with float switch, CEE plug

and transport frame

InformationOnline catalogue www.wilo.comBuilding Services catalogue

DesignPump stations with synthetic tanks, as a single- or double-pump system

Q max. 180 m³/h

H max. 55 m

Special features• Deposit-free collection space• Maximum strength due to hemispherically

shaped sump floor• 2/4 inlets can be selected onsite• stainless steel pipework• Also with Wilo-Drain MTS 40..., MTC 40 or

MTC 32 macerator pump

Technical data• Synthetic pumps station made of

recyclable PE• Maximum upward pressure reliability due

to 2 or 4 lateral fins• 2/4 inlets can be selected onsite• Maximum stability due to moulded

hemispherical shape of the sump floor• Wilo surface coupling• Good accessibility of the level sensor due

to installation with hinged supporting bar• Max. traffic load 5 kN/m² (in accordance

with DIN EN 124, Group 1)• Max. pressure in the pressure pipe 6 bar

Equipment/functionWilo-Drain pumps that can be used:TS 40TP 50TP 65STS 65TP 80MTC 32MTC 40MTS 40


Design Baseplate pump with axial suction

Q max. 1,650 m³/h

H max. 103 m

Special features• Motors in IE2 technology with higher

efficiency as standard• Reduced life cycle costs due to optimised

efficiency• Bidirectional mechanical seal with forced flushing

• Replaceable stationary wear rings• Low NPSH-values, best cavitation

properties• High availability of IEC standard motors

Worldwide

Technical data• Permitted temperature range -20 °C to

+120 °C• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameters DN 150 to DN 300• Max. operating pressure 16 bar

Equipment/function• Single-stage horizontal spiral housing

pump with bearing bracket and replaceable stationary wear rings in process construction

• Shaft sealing by means of mechanical seals according to EN 12756 or stuffing box packing

• Spiral housing with directly cast pump feet. Bearing of the pump shaft by means of grease-lubricated grooved ball bearings

• Shaft coupling with intermediate sleeve

Materials:• Pump housing and pressure cover: EN-

GJS-500-7• Bearing bracket: EN-GJL-250• Impeller: EN-GJL-250 (special version:

G-CuSn10)• Shaft: 1.4028• Stationary wear rings: G-CuSn10• Mechanical seal: AQ1EGG (other

mechanical seals on request)



Submersible sewage pumpsSeriesWilo-EMU FA 08 … to FA 15 …(Standard products)

Submersible sewage pumpsSeriesWilo-Drain TP 80Wilo-Drain TP 100Wilo-Drain TP...-AM

Pumps station with synthetic tankSeriesWilo DrainLift WS 830Wilo-DrainLift WS 900Wilo-DrainLift WS 1100

Standard glanded pumpsSeriesWilo-CronoNorm-NLG

Self-priming multistage pumps andpump systemsSeriesWilo-MultiPress MPWilo-MultiPress HMPWilo-MultiPress FMP

Vertical, multistage centrifugal pumpsSeriesWilo-Helix-VE

Vertical, multistage centrifugal pumpsSeriesWilo-Helix EXCEL

Vertical, multistage centrifugal pumpsSeriesWilo-Multivert-MVIE

Design Non-self-priming multistage centrifugal Pumps

Q max. 8 m³/h

H max. 57 m


utilisation• HMP version with diaphragm pressure

vessel and pressure switch• FMP version with fluid control for system

control

Technical data • Mains connection 1~230 V, 50 Hz

3~400 V, 50 Hz• Inlet pressure max. 6 bar• Fluid temperature max. +5 °C to +35 °C• Ambient temperature max. +40 °C• Operating pressure max. 10 bar• Protection class IP 54• Suction/pressure side connections: -MP 3.. Rp 1 (Rp 1); MP 6.. Rp 1¼/Rp 1 -FMP 3.. R 1/Rp 1; FMP 6.. R 1¼/Rp 1 -HMP 3.. Rp 1/Rp 1; HMP 6.. Rp 1¼/Rp 1


1~230 V version


Design Non-self-priming multistage pump with integrated frequency converter

Q max. 80 m³/h

H max. 240 m

Special features • Efficiency-optimised, laser-welded

2D/3D high-efficiency hydraulics• Easy pump replacement without pipe

modification. Due to the modular pump housing, Helix pumps can be installed in existing pipes.

• User-friendly mechanical seal with cartridge, equipped with a standard seal for easy maintenance

• Potable water approval according to ACS/KTW/WRAS for all parts that come in contact with the fluid

Technical data • Fluid temperature -20 to +120 °C• Operating pressure max. 16/25 bar• Inlet pressure max. 10 bar• Protection class IP 55• PN 16 and PN 25 with loose round flanges

Equipment/function • Impellers, stage chambers and pump

housing stainless steel 1.4301/1.4404 (AISI304L/AISI316L)

• Versions with 1.44xx stainless steel designed for aggressive fluids

• PN 16 and PN 25 versions with round loose flanges in accordance with ISO 2531 and ISO 7005

• IE2/IEC standard three-phase AC motor• Integrated frequency converter


Design Non-self-priming multistage pump with EC motor with integrated high-efficiency Drive

Q max. 58 m³/h

H max. 243 m


2D/3D high-efficiency hydraulics• Built-in electronic control thanks to the

High Efficiency Drive with large control range

• Choice of various different control modes (speed control, constant pressure, and PID).


• The spacer coupling enables the mechanical seal to be replaced without dismantling the motor (from 7.5 kW and higher)

• Intermediate bearings (Al203/CW) ensure a long service life

• WRAS/KTW/ACS approval for all parts that come in contact with the fluid (EPDM version)

Technical data • Fluid temperature: -20 to +120 °C with

EPDM (-10 to +90 °C with FKM gasket)• Operating pressure max.: 16/25 bar• Protection class: IP 55• Helix EXCEL 2-16: PN 16 with oval flanges and PN 25 with round flanges in accordance with ISO 2531 and ISO 7005• Helix EXCEL 22-36: PN 25 with round flanges in accordance

with ISO 2531 and ISO 7005

Equipment/function • Impellers, diffusors and stage housings

made of stainless steel• Versions in 1.44xx stainless steel for

aggressive fluids• High-efficiency EC motor (degrees of

efficiency higher than the IE4 limit values acc. to IEC TS 60034-31 Ed.1)

• Optional interfaces for BUS communication via plug-in IF-modules



Q max. 145 m³/h

H max. 245 m

Special features • Easy commissioning• Full motor protection• Large control range• MVIE 2..-16..-6

All parts that come in contact with the fluid made of stainless steel 1.4301 (AISI 304) or 14404 (AISI 316L)

• MVIE 16..-95.. depending on pump type in stainless steel

1.4404 (AISI 316L) or 1.4301 (AISI 304) with pump housing made of grey cast iron EN-GJL-250, cataphoretic coating

• All relevant components have KTW and WRAS approval

Technical data • Fluid temperature -15 to +120 °C• Operating pressure max. 16 bar/25 bar• Inlet pressure max. 10 bar• Protection class IP 54 or IP 55

Equipment/function • Stainless steel pump in in-line design• PN 16 with oval flanges• PN 16/25 with DIN round flanges,

Victaulic connections depending on pump type

• Single-phase or three-phase current standard motor

• Integrated frequency converter• Integrated thermal motor protection• Protection against low water level



7

Submersible drainage pumpsSeriesWilo-Drain TMTWilo-Drain TMC

Submersible sewage pumps withmaceratorSeriesWilo-Drain MTC…Wilo-Drain MTS…

Submersible sewage pumpsSeriesRexa FITRexa PRO

DesignSubmersible drainage pumps

Q max.22 m³/h

H max.13 m

Special features• High temperature resistance• Also suitable for aggressive fluids

Technical data• Mains connection 3~400 V, 50 Hz• Protection class IP 68• Submersion depth max. 5 m• Fluid temperature 95 °C, 65 °C non-

immersed• Cable length 10 m• Free ball passage 10 mm• Pressure port, depending on type Rp 1¼

or Rp 1½

Equipment/function• Pump housing and impeller made of

DesignSubmersible sewage pumps with Macerator

Q max.17 m³/h

H max.55 m

Special features• Oil barrier chamber• High degree of efficiency• Mechanical seal on pump side made of

solid silicon carbide material• External hardened macerator (MTC)• Internal, spherically formed macerator

(MTS)• Longitudinally watertight cable• Version with Ex protection (depending on

type)

Technical data• Mains connection: 1~230 V, 50 Hz or

3~400 V, 50 Hz• Immersed operating mode: S1 / S3 25 %

(depending on type)• Protection class: IP 68• Insulation class: F• Thermal winding monitoring• Max. fluid temperature: 3-40 °C



Q max. 95 m³/h

H max. 29 m

Special features• Vortex impeller non-susceptible to

clogging• Seal by two mechanical shaft seals• Optional external sealing chamber control

for the oil barrier chamber• Very smooth operation• Easy installation due to suspension unit or

pump base• Ex-rated in accordance with ATEX as

standard (Rexa PRO)• Longitudinally watertight cable inlet• Operation with frequency converter

(Rexa PRO)

Technical data• Mains connection: 1~230 V, 50 Hz or

3~400 V, 50 Hz• Immersed operating mode: S1• Non-immersed operating mode:

--Rexa FIT: S2-15 min; S3 25 % --Rexa PRO: S2-30 min, S3 50 %

• Protection class: IP 68• Insulation class: F• Fluid temperature: 3-40 °C, max. 60 °C

for 3 min• Free passage: 50/65/80 mm• Max. immersion depth: 20 m• Cable length: 10 m

Equipment/function• Winding temperature monitoring with

Product category Product category Product category

9

Equipment/function• Pump housing and impeller made of

grey cast iron, bronze or stainless steel, depending on version


Equipment/function• Heavy-duty version made of cast iron• Unimpeded flow to the impeller• Maceration of substances being pumped• Simple installation via suspension unit or

pump base vAttached float switch (only model A)

MTC:• External maceratorMTS:• Innovative patented macerator• Internal rotating blade• Spherically formed macerator• Pulling cut (shearing cut)

InformationOnline catalogue www.wilo.comBuilding Services catalogue,Drainage and Sewag

Equipment/function• Winding temperature monitoring with

bimetal sensor• Optional external sealing chamber control

for the oil barrier chamber• Leakage detection for the motor

compartment (Rexa PRO)


Design Pressure boosting system with 2 to 6 non-self-priming, stainless steel, highpressure, multistage centrifugal pumps switched in parallel

Q max. 800 m³/h

H max. 160 m

Special features • Compact system in accordance with the

requirements of DIN 1988• 2 to 4 or 2 to 6 high-pressure, multistage

centrifugal pumps switched in parallel• Easily adjustable and operationally reliable

due to integrated control devices• Series with Helix-V with IE2 motorsFor systems with MVIS pumps• Virtually noiseless system due to a

glandless, high-pressure, multistage centrifugal pump

• Up to 20 dB (A) quieter than conventional systems with comparable hydraulic output

Technical data • Mains connection 3~230 V / 400 V, 50 Hz• Fluid temperature max. 50 °C• Operating pressure 10/16 bar• Inlet pressure 6/10 bar• Protection class IP 54

Design Pressure boosting system with speed control and 2 to 6 non-self-priming, stainless steel, high-pressure, multistage centrifugal pumps switched in parallel

Q max. 800 m³/h

H max. 160 m

Special features • Easy-to-use system in accordance with

all requirements of DIN 1988• 2 to 6 vertical high-pressure multistage

centrifugal pumps switched in parallel• Speed-controlled base-load pump• Series with Helix-V and -VE with IE2

motors• Series with Helix-VE with integrated

frequency converter with converter with wide control range

For systems with MVIS pumps• Virtually noiseless system due to a

glandless, high-pressure, multistage centrifugal pump

• Up to 20 dB (A) quieter than conventional systems with comparable hydraulic output

Technical data • Mains connection 3~230 / 400 V, 50 Hz• Fluid temperature max. 50 °C• Operating pressure 10/16 bar• Inlet pressure 6/10 bar• Protection class IP 54

Design Highly efficient pressure boosting system with 2 to 4 non-self-priming, stainless steel, highpressure, multistage centrifugal pumps (Helix V, VE or EXCEL) switched in parallel, including Smart Controller SC (available with and without frequency converter FC).

Q max. 132 m³/h

H max. 159 m

Special features• High-efficient pump hydraulics• IE2 equivalent standard motors. Systems

with Helix EXCEL with EC Motor (> IE4)• Entire system hydraulics pressure loss

optimised• Superproportionally large control range

of frequency converter from 25 Hz to a maximum of 60 Hz

• Integrated dry-running detection with automatic cut-out via performance characteristics of the motor control electronics

• Ultimate control quality and supremely easy operation due to the SC controller, with symbols-based LCD display, easy navigation, quick adjustment of parameters, integrated frequency converter

Technical data • Mains connection with Helix V: 3~230 V

/ 400 V, 50 Hz V with Helix VE and EXCEL: 3~400 V, 50 Hz

• Fluid temperature max. +50 °C (+70 °C / option)

• Operating pressure 16 bar (25 bar / option)

• Inlet pressure 10 bar• Nominal connection diameters R 1½” -

DN 100• Protection class: IP 54

Design Submersible drainage pumps

Q max. 53 m³/h

H max. 25 m

Special features• Inox & composite• Low weight• Detachable connection cable• Detachable float switch for model A• Thermal motor monitoring for AC motor

without switchgear

Technical data• Mains connection 1~230 V, 50 Hz or

3~400 V, 50 Hz• Protection class IP 68• Submersion depth 5 to 10 m• Fluid temperature 3 °C to 35 °C• Free ball passage 10 mm• Pressure port, depending on type Rp 1½,

Rp 2 or Rp 2½


Multi-pump pressure boosting systemsSeriesWilo-Economy CO 2-4 MHI … /ERWilo-Comfort-N-CO 2-6 MVIS … /CCWilo-Comfort-CO 2-6 MVI … /CCWilo-Comfort-CO 2-6 Helix-V … /CC

Multi-pump pressure boosting systemswith speed controlSeriesWilo-Comfort-N-COR 2-6 MVIS … /CCWilo-Comfort-COR 2-6 MVI … /CCWilo-Comfort-COR 2-6 Helix-V … /CCWilo-Comfort-COR 2-6 Helix VE.../CCe

Multi-pump pressure boosting systemsSeriesWilo-SiBoost Smart Helix VWilo-SiBoost Smart Helix VEWilo-SiBoost Smart Helix EXCEL

Submersible drainage pumpsSeriesWilo-Drain TS 40Wilo-Drain TS 50Wilo-Drain TS 65

Equipment/function • 2 to 4 or 2 to 6 pumps per system• Components that come in contact with fluid are corrosion-resistant

• Galvanised base frame with heightadjustable vibration dampers for insulation against structure-borne noise

• Pipework in stainless steel 1.4571• Gear-operated shut-off ball cock/ annular

shut-off valve on every pump, on suction and pressure sides

• Non-return valve, on pressure side• Diaphragm pressure vessel 8 l, PN 16, on

pressure side• Pressure sensor, on discharge side


Equipment/function • 2 to 6 pumps per system• Continuous control operation of the

base-load pump via frequency converter integrated in the CC controller

• Components that come in contact with fluid are corrosion-resistant

• Galvanised base frame with heightadjustable vibration dampers for insulation against structure-borne noise

• Pipework in stainless steel 1.4571• Gear-operated shut-off ball cock/ annular

shut-off valve on every pump, on suction and pressure sides

• Non-return valve, on pressure side• Diaphragm pressure vessel 8 l, PN 16, on

pressure side• Pressure sensor, on discharge side


Equipment/function• 2-4 pumps per system• Automatic pump control via Smart

Controller SC. Version SC-FC with frequency controller included

• Components that come in contact with fluid are corrosion-resistant

• Galvanised base frame with heightadjustable vibration dampers for insulation against structure-borne noise cable guidance and integrated hoisting gear

• Shut-off valve on the suction and pressure side of each pump

• Non-return valve, on pressure side• Pressure sensor and pressure gauge,

discharge side• Optional low-water cut-out switchgear


Equipment/function• Ready-to-plug versions also with float

switch• Thermal motor monitoring• Explosion protection for TS 50 and TS 65• Connection cable 10 m• Connection cable detachable• Integrated non-return valve for TS 40• Hose connection for TS 40



Q max. 380 m³/h

H max. 51 m

Special features• Operation in stationary and portable wet

well installation• Heavy-duty version made of cast iron• Easy installation due to suspension unit

or pump base• Longitudinally watertight cable lead-in• ATEX approval

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Surfaced operating mode: S2-15 or

S2-30 (depending on type)• Thermal motor monitoring• Protection class: IP 68• Insulation class: F• Max. fluid temperature: 40 °C• Free ball passage of 45 to 100 mm• Permanently lubricated anti-friction


Equipment/function• Heavy-duty version made of cast iron• Simple installation via suspension unit or

pump base


DesignSubmersible sewage pump for industrial Applications

Q max. 180 m³/h

H max. 21 m

Special features• Stainless steel & composite• ATEX approval (not for model “AM”)• Low weight• Detachable connection cable• Standard-equipped with cooling jacket• Corrosion-resistant (e.g. swimming pool

water, salt water, etc.)

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Surfaced operating mode: S1• Protection class: IP 68• Insulation class: F• Thermal winding monitoring• Sealing chamber control• Max. fluid temperature: 40 °C• Free ball passage: 80 or 100 mm• Max. immersion depth: 20 m

Equipment/function• Thermal motor monitoring• Sealing chamber monitoring• ATEX approval (not for model “AM”)• Sheath current cooling• Model “AM” with float switch, CEE plug

and transport frame

InformationOnline catalogue www.wilo.comBuilding Services catalogue

DesignPump stations with synthetic tanks, as a single- or double-pump system

Q max. 180 m³/h

H max. 55 m

Special features• Deposit-free collection space• Maximum strength due to hemispherically

shaped sump floor• 2/4 inlets can be selected onsite• stainless steel pipework• Also with Wilo-Drain MTS 40..., MTC 40 or

MTC 32 macerator pump

Technical data• Synthetic pumps station made of

recyclable PE• Maximum upward pressure reliability due

to 2 or 4 lateral fins• 2/4 inlets can be selected onsite• Maximum stability due to moulded

hemispherical shape of the sump floor• Wilo surface coupling• Good accessibility of the level sensor due

to installation with hinged supporting bar• Max. traffic load 5 kN/m² (in accordance

with DIN EN 124, Group 1)• Max. pressure in the pressure pipe 6 bar

Equipment/functionWilo-Drain pumps that can be used:TS 40TP 50TP 65STS 65TP 80MTC 32MTC 40MTS 40


Design Baseplate pump with axial suction

Q max. 1,650 m³/h

H max. 103 m

Special features• Motors in IE2 technology with higher

efficiency as standard• Reduced life cycle costs due to optimised

efficiency• Bidirectional mechanical seal with forced flushing

• Replaceable stationary wear rings• Low NPSH-values, best cavitation

properties• High availability of IEC standard motors

Worldwide

Technical data• Permitted temperature range -20 °C to

+120 °C• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameters DN 150 to DN 300• Max. operating pressure 16 bar

Equipment/function• Single-stage horizontal spiral housing

pump with bearing bracket and replaceable stationary wear rings in process construction

• Shaft sealing by means of mechanical seals according to EN 12756 or stuffing box packing

• Spiral housing with directly cast pump feet. Bearing of the pump shaft by means of grease-lubricated grooved ball bearings

• Shaft coupling with intermediate sleeve

Materials:• Pump housing and pressure cover: EN-

GJS-500-7• Bearing bracket: EN-GJL-250• Impeller: EN-GJL-250 (special version:

G-CuSn10)• Shaft: 1.4028• Stationary wear rings: G-CuSn10• Mechanical seal: AQ1EGG (other

mechanical seals on request)



Submersible sewage pumpsSeriesWilo-EMU FA 08 … to FA 15 …(Standard products)

Submersible sewage pumpsSeriesWilo-Drain TP 80Wilo-Drain TP 100Wilo-Drain TP...-AM

Pumps station with synthetic tankSeriesWilo DrainLift WS 830Wilo-DrainLift WS 900Wilo-DrainLift WS 1100

Standard glanded pumpsSeriesWilo-CronoNorm-NLG

Self-priming multistage pumps andpump systemsSeriesWilo-MultiPress MPWilo-MultiPress HMPWilo-MultiPress FMP

Vertical, multistage centrifugal pumpsSeriesWilo-Helix-VE

Vertical, multistage centrifugal pumpsSeriesWilo-Helix EXCEL

Vertical, multistage centrifugal pumpsSeriesWilo-Multivert-MVIE

Design Non-self-priming multistage centrifugal Pumps

Q max. 8 m³/h

H max. 57 m


utilisation• HMP version with diaphragm pressure

vessel and pressure switch• FMP version with fluid control for system

control

Technical data • Mains connection 1~230 V, 50 Hz

3~400 V, 50 Hz• Inlet pressure max. 6 bar• Fluid temperature max. +5 °C to +35 °C• Ambient temperature max. +40 °C• Operating pressure max. 10 bar• Protection class IP 54• Suction/pressure side connections: -MP 3.. Rp 1 (Rp 1); MP 6.. Rp 1¼/Rp 1 -FMP 3.. R 1/Rp 1; FMP 6.. R 1¼/Rp 1 -HMP 3.. Rp 1/Rp 1; HMP 6.. Rp 1¼/Rp 1


1~230 V version



Q max. 80 m³/h

H max. 240 m


2D/3D high-efficiency hydraulics• Easy pump replacement without pipe

modification. Due to the modular pump housing, Helix pumps can be installed in existing pipes.


• Potable water approval according to ACS/KTW/WRAS for all parts that come in contact with the fluid

Technical data • Fluid temperature -20 to +120 °C• Operating pressure max. 16/25 bar• Inlet pressure max. 10 bar• Protection class IP 55• PN 16 and PN 25 with loose round flanges

Equipment/function • Impellers, stage chambers and pump

housing stainless steel 1.4301/1.4404 (AISI304L/AISI316L)

• Versions with 1.44xx stainless steel designed for aggressive fluids

• PN 16 and PN 25 versions with round loose flanges in accordance with ISO 2531 and ISO 7005

• IE2/IEC standard three-phase AC motor• Integrated frequency converter


Design Non-self-priming multistage pump with EC motor with integrated high-efficiency Drive

Q max. 58 m³/h

H max. 243 m


2D/3D high-efficiency hydraulics• Built-in electronic control thanks to the

High Efficiency Drive with large control range

• Choice of various different control modes (speed control, constant pressure, and PID).


• The spacer coupling enables the mechanical seal to be replaced without dismantling the motor (from 7.5 kW and higher)

• Intermediate bearings (Al203/CW) ensure a long service life

• WRAS/KTW/ACS approval for all parts that come in contact with the fluid (EPDM version)

Technical data • Fluid temperature: -20 to +120 °C with

EPDM (-10 to +90 °C with FKM gasket)• Operating pressure max.: 16/25 bar• Protection class: IP 55• Helix EXCEL 2-16: PN 16 with oval flanges and PN 25 with round flanges in accordance with ISO 2531 and ISO 7005• Helix EXCEL 22-36: PN 25 with round flanges in accordance

with ISO 2531 and ISO 7005

Equipment/function • Impellers, diffusors and stage housings

made of stainless steel• Versions in 1.44xx stainless steel for

aggressive fluids• High-efficiency EC motor (degrees of

efficiency higher than the IE4 limit values acc. to IEC TS 60034-31 Ed.1)

• Optional interfaces for BUS communication via plug-in IF-modules



Q max. 145 m³/h

H max. 245 m

Special features • Easy commissioning• Full motor protection• Large control range• MVIE 2..-16..-6

All parts that come in contact with the fluid made of stainless steel 1.4301 (AISI 304) or 14404 (AISI 316L)

• MVIE 16..-95.. depending on pump type in stainless steel

1.4404 (AISI 316L) or 1.4301 (AISI 304) with pump housing made of grey cast iron EN-GJL-250, cataphoretic coating

• All relevant components have KTW and WRAS approval

Technical data • Fluid temperature -15 to +120 °C• Operating pressure max. 16 bar/25 bar• Inlet pressure max. 10 bar• Protection class IP 54 or IP 55

Equipment/function • Stainless steel pump in in-line design• PN 16 with oval flanges• PN 16/25 with DIN round flanges,

Victaulic connections depending on pump type

• Single-phase or three-phase current standard motor

• Integrated frequency converter• Integrated thermal motor protection• Protection against low water level



7

Standard glanded pumpsSeriesWilo-CronoNorm-NLWilo-VeroNorm-NPG

Axially split case pumpsSeriesWilo-SCP

Submersible pumpsSeriesWilo-Sub TWI 4 …Wilo-Sub TWI 6 …Wilo-Sub TWI 8 …Wilo-Sub TWI 10 …

Submersible pumpsSeriesWilo-EMU 6” seriesWilo-EMU 8” seriesWilo-EMU 10”…24” series

Design Single-stage low-pressure centrifugal pump with axial suction, in accordance with EN 733 and ISO 5199, mounted on baseplate.

Q max. 3,000 m³/h

H max. 140 m

Special features• Motors with higher efficiency as standard;


• Other materials and versions on request




to DN 500• Maximum operating pressure: depending

on type and application up to 16 bar

Equipment/functionSingle-stage low-pressure centrifugal pump in monobloc design with coupling, coupling protection, motor and baseplate• Mechanical seal or stuffing box• Wilo factory motor or ATB motor

Materials:• Pump housing: EN-GJL-250• Impeller: EN-GJL-250• Shaft: 1.4028


DesignLow-pressure centrifugal pump with axially split housing mounted on a Baseplate

Q max. 3,400 m³/h

H max. 245 m

Special features• Higher capacities up to 17,000 m³/h on

request• Special motors and other materials on

Request




to DN 400• Max. operating pressure: depending on

type 16 or 25 bar

Equipment/function1- or 2-stage, low-pressure centrifugal pump in monobloc design• Delivered as complete unit (pump with

coupling, coupling protection, motor and baseplate) or without motor or only pump hydraulics

• Shaft seal with mechanical seal or stuffing box

• 4-pole and 6-pole motors

Materials:• Pump housing: EN-GJL-250• Impeller: GCuSn5 ZnPb• Shaft: X12Cr13


DesignSubmersible pump, multistage

Q max.165 m³/h

H max.500 m

Special features• Unit made completely of stainless steel• Integrated non-return valve• Vertical and horizontal installation

possible• Standard and configurable versions

available (TWI 6 … / TWI 8 … / TWI 10...)• Star-delta version• Rewindable motors

Technical data• Mains connection: 1~230 V, 50 Hz (only

TWI 4 …) or 3~400 V, 50 Hz• Immersed operating mode: S1• Fluid temperature: 3-20 °C or 3-30 °C• Min. flow at motor: 0.08-0.5 m/s• Max. sand content: 50 g/m³• Up to 10 or 20 starts per hour• Max. immersion depth: 100-350 m• Protection class: IP 68

Equipment/function• Multistage submersible pump with radial

or semi-axial impellers• Integrated non-return valve• NEMA coupling• AC-(only TWI 4) or three phase motor• Hermetically sealed or rewindable (TWI 6

… / TWI 8 … / TWI 10...) motors


Design Submersible pump with sectional Construction

Q max. 2,400 m³/h

H max. 560 m

Special features• Water pumping with large volume flows• Corrosion-resistant impellers• Wear-resistant GI bushing (depending on

type)• Special materials possible• Individual adjustment to duty point due

to impeller correction• 4-pole motors for long service life and

high degree of efficiency• Motors with CoolAct technology for high

power density (from 10” motors on)• High voltage up to 6000 V possible• Vertical and horizontal installation

possible• Ceram CT coating possible to increase

effectiveness• Pressure shroud installation option

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Max. fluid temperature: 20...30 °C• Min. flow at motor: 0.1 ... 0.5 m/s• Max. sand content: 35 g/m³• Up to 10 starts per hour• Max. immersion depth: 100 or 300/350 %• Protection class: IP 68• Control range for frequency converter:

25...50 or 30...50 Hz

Equipment/function• Immersible, multistage submersible pump• Radial or semi-axial impellers• Hydraulics and motor freely configurable

according to power requirements• Integrated non-return valve (depending

on type)• NEMA coupling or standardised

connection (from 10” motors on)• Three-phase motor for direct or stardelta

start.



11

Design Glanded pump in monobloc design with flange connection

Q max. 360 m³/h

H max. 105 m



• Meets user requirements due to performance and main dimensions in accordance with EN 733

• Long motor life due to standard condensate drainage holes in the motor housing

• Corrosion protection due to cataphoretic coating


to +140 °C• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameter DN 32 to DN 150• Max. operating pressure 16 bar

(25 bar on request)

Equipment/function Single-stage low-pressure centrifugal pump in block design, with axial suction port and radially arranged pressure port with• Mechanical seal• Flange connection with pressure

measuring connection R ⅛• Lantern• Coupling• IEC standard motor

Materials: • Pump housing standard: EN-GJL-250Optional: EN-GJS-400-18• Impeller (standard): EN-GJL-200Special version: Bronze G-CuSn10• Shaft: 1.4122• Mechanical seal: AQEGGOther mechanical seals on request


Design Glanded pump in monobloc design with threaded connection or Victaulic Connection

Q max. 80 m³/h

H max. 25 m




• Pump housing in plastic design• Version with Victaulic or threaded

connection (BAC 70/135... with Victaulic connection only)

Technical data • Perm. temperature range -15 °C to

+60 °C• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameter G2/G 1½

(only BAC 40… /S) or Victaulic connection ∅ 60.3/48.3 mm (BAC 40… /R) ∅ 76.1/76.1 mm (BAC 70…/R)• Max. operating pressure 6.5 bar

Equipment/function Single-stage low-pressure centrifugalpump in monobloc design, with axialsuction port and radially arrangedpressure port

Materials: • Pump housing: PA 6.6 50 % GF• Impeller: PA/PPO, fibreglass-reinforced• Shaft: X30Cr13• Mechanical seal: BQEGG


Design Automatic rainwater utilisation system with run-down tank container and 2 non self-priming pumps

Q max. 16 m³/h

H max. 56 m

Special features • Low-noise due to multistage centrifugal

pumps• All parts that come in contact with the fluid are corrosion-free

• Maximum operational reliability, due to trendsetting fully electronic RainControl Hybrid controller

• High economic efficiency due to fresh water replenishment according to requirements

• High reliability, due to flow- and noiseoptimised overall concept

• Automatic control of the feeding pump• System/level control in the low-voltage

Range

Technical data • Mains connection 3~400 V, 50 Hz• Fluid temperature max. +5 °C to +35 °C• Operating pressure max. 10 bar• Replenishment reservoir 400 l• Protection class IP 54

Equipment/function • Connection-ready module with compact

construction• Fully connected electrically and

hydraulically• Mounted on vibration-insulated

baseplate• 2 MultiPress MP centrifugal pumps

(non-self-priming)• Joint tubing R 1½” on the pressure side,

inc. transmitter unit, diaphragm pressure vessel, shut-off device

• Pressure gauge 0-10 bar• Ball valve on suction and pressure sides

and non-return valve• High-volume hybrid tank with all

connections, calmed inlets and overflow with siphon

• RainControl Hybrid central switchgear with control electronics

• Signals concerning operation and faults• Cyclical pump cycling and test run when

pump at rest• Automatic fault-actuated switchover and

peak-load cut-in• Automatic water exchange in the

replenishment reservoir• Permanent display of rainwater storage

tank level, system pressure, operating status (optional)


Design Self-priming multistage centrifugal Pumps

Q max. 7 m³/h

H max. 57 m


utilisation• HMC version with diaphragm pressure

vessel and pressure switch• FMC version with fluid control for system

control

Technical data • Mains connection 1~230 V, 50 Hz 3~400

V, 50 Hz• Inlet pressure max. 4 bar• Fluid temperature max. +5 °C to +35 °C• Ambient temperature max. +40 °C• Operating pressure max. 8 bar• Protection class IP 54• Suction/pressure side connections: -MC (Rp 1/Rp 1) -FMC (R 1/Rp 1) -HMC (Rp 1/Rp 1)


single-phase AC motor (1~230 V



Glanded monobloc pumpsSeriesWilo-CronoBloc-BL

Glanded monobloc pumpsSeriesWilo-BAC

Rainwater utilisation systemsSeriesWilo-RainSystem AF 400

Self-priming multistage pumps andpump systemsSeriesWilo-MultiCargo MCWilo-MultiCargo HMCWilo-MultiCargo FMC

Design Submersible bottom intake pump

Q max. 1,200 m³/h

H max. 160 m

Special features• Deep water lowering• Self-cooling design• Easy installation on the ascending pipe• Wear-resistant design due to different

material versions• Compact design• Rewindable motors• Individual adjustment to duty point due

to impeller correction• Ceram CT coating possible to increase

Effectiveness

Technical data• Mains connection: 3~400 V, 50 Hz• Max. fluid temperature: 20 °C• Min. flow at outside shroud: not necessary• Max. sand content: 35 g/m³• Up to 10 starts per hour• Max. immersion depth: 300 m• Protection class: IP 68• Control range for frequency converter:

--2-pole: 25-50 Hz --4-pole: 30-50 Hz

Equipment/function• Immersible, multistage submersible pump• Semi-axial impellers• Hydraulics and motor freely configurable

according to power requirements• Three-phase motor for direct or stardelta

start.• Motors rewindable as standard


Design Dry installed vertical turbine pumps with immersed axial- or semi-axial hydraulics

Q max. 40,000 m³/h

H max. 450 m

Special features• Minimum surface area needed• High hydraulic efficiency• immersed pump hydraulics• Design to order as per customer

Specifications

Technical data• Perm. temperature range to 80 °C 105 °C• Nominal diameter DN 100 to DN 2000

Equipment/functionFor installation types with pressure portsfor underground, above-ground or twinroofinstallation• Design

-- as removable or permanent installation

-- with axial or semi-axial, single or multistage hydraulics

-- with open shaft for bearing lubrication with the fluid or with shaft trim for separate bearing lubrication

• Drive options: Electric motor, Diesel motor or steam turbine

InformationDocumentation on request

Design Axial submersible pump with dry motor for use in pipe sumps

Q max. 9,500 m³/h

H max. 8.4 m

Special features• Special materials and coatings against

abrasion and corrosion• Longitudinally watertight cable lead-in• Angle of propeller blades adjustable by

hand

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Protection class: IP 68• Max. fluid temperature: 40 °C, higher

temperatures on request• Sealing with two mechanical seals or one

block seal cartridge, depending on motor• Free ball passage of 85 to 130 mm• Short common pump/motor shaft• Permanently lubricated anti-friction



InformationOnline catalogue www.wilo.comCatalogue Water Management

Design Compact directly driven submersible Mixer


Special features • Low power consumption• Low weight• ATEX and FM versions• Self-cleaning propeller with helix hub• Easy-to-install propeller attachment• Propeller in steel or PUR version• Optional: Motor shaft made of 1.4462

material

Technical data • Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Protection class: IP 68• Max. fluid temperature: 40 °C• Mechanical seal with SiC/SiC combination• Permanently lubricated anti-friction


Equipment/function• Stationary installation on walls and floors• Flexible installation through the use

of lowering device or special pipe attachment

• Can be swivelled vertically and horizontally for installation with lowering device



Submersible pumpsSeriesWilo-EMU bottom intake pumps

Vertical turbine pumpsSeriesSeries VMF, CNE, VAF

Submersible sewage pumpsSeriesWilo-EMU KPR …


Glanded standard pumps inin-line designSeriesWilo-VeroLine-IPLWilo-VeroTwin-DPL

Glanded standard pumps inin-line designSeriesWilo-CronoLine-ILWilo-CronoTwin-DL

Special glanded pumps in in-line designSeriesWilo-VeroLine-IPH-WWilo-VeroLine-IPH-O

Special glanded pumps in in-line designSeriesWilo-VeroLine-IPS


Q max. 245 m³/h

H max. 52 m



• Standard condensate drainage holes in the motor housings and lanterns

• Series version: Motor with one-piece shaft

• Version N: Standard motor B5 or V1 with stainless steel plug shaft




+120 °C• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameter Rp 1 to DN 100• Max. operating pressure 10 bar

(special version: 16 bar)

Equipment/function Single-stage, low-pressure centrifugal pump in in-line design with• Mechanical seal• For flange connection with pressure

measuring connection R ½• Motor with one-piece shaft• DPL with switchover valve

Materials: • Pump housing and lantern: EN-GJL-250• Impeller: PPO fibreglass-reinforced

EN-GJL-200 (depending on pump type)• Shaft: 1.4021• Mechanical seal: AQEGG; other

mechanical seals on request

InformationOnline catalogue www.wilo.com Building Services catalogue, Heating, Air-Conditioning, Cooling


Q max. 1,150 m³/h

H max. 110 m




• Standard condensate drainage holes in the motor housings

• Can be used flexibly in air-conditioning and cooling systems, with application benefits due direct draining of condensate via optimised lantern design (patented)


• High worldwide availability of standard motors (according to Wilo specifications) and standard mechanical seals


Technical data• Perm. temperature range -20 °C

to+140 °C• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameter DN 32 to DN 250• Max. operating pressure 16 bar (25 bar on request)

Equipment/functionSingle-stage, low-pressure centrifugal pump in in-line design with• Mechanical seal• Flange connection with pressure

measuring connection R ½• Lantern• Coupling• IEC standard motor• DL with switchover valve

Materials: • Pump housing and lantern:

Standard version: EN-GJL-250Optional: Spheroidal cast iron EN-GJS-400-18-LT• Impeller:

Standard: EN-GJL200Special version: Red brass G-CuSn 10 • Shaft: 1.4122• Mechanical seal: AQEGGOther mechanical seals: on request



Q max. 80 m³/h

H max. 38 m

Special features • From 0.75 kW nominal motor power

motors with IE2 technology for higher efficiency fitted as standard

• Bidirectional, self-cooled mechanical seal• Great variety of applications by a

large fluid temperature range without additional wearing parts

Technical data• Permissible temperature range IPH-W:

-10 °C to +210 °C (at a max. of 23 bar)• Permissible temperature range IPH-O:

-10 °C to +350 °C (at a max. 9 bar)• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameter DN 20 to DN 80

Equipment/function Single-stage, low-pressure centrifugal pump in in-line design with• Mechanical seal• Flange connection• Lantern• Motor with special shaft



Q max. 13 m³/h

H max. 3 m

Special features • Worldwide availability of the standard

motors used


to+140 °C• Mains connection 3~400 V, 50 Hz• Protection class IP 55• Nominal diameter Rp 1, DN 40 and DN 50• Max. operating pressure 10 bar or 6 bar

for flange connection

Equipment/function Single-stage, low-pressure centrifugal pump in in-line design with• Mechanical seal or stuffing box• Threaded or flange connection with

pressure measuring connection R ⅛• Standard motor

Materials: • Pump housing and lantern: EN-GJL-200• Impeller: Plastic• Shaft: 1.4021• Mechanical seal: BVEGGOther mechanical seals on request



5


Submersible mixerSeriesWilo-EMU TR 50-2 to TR 90-2Wilo-EMU TRE 90-2 with IE3 motor

Submersible mixerSeriesWilo-EMU TR 212 to TR 226Wilo-EMU TR 316 to TR 326Wilo-EMU TRE with IE3 motor

Recirculation pumpSeriesWilo-EMU RZP 20 to RZP 80-2

Design Compact directly driven submersibleMixer


Special features • Self-cleaning propeller with helix hub• Easy-to-install propeller attachment• Propeller in steel or PUR version• ATEX and FM versions

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Protection class: IP 68• Max. fluid temperature: 40 °C• Mechanical seal with SiC/SiC combination• Permanently lubricated anti-friction


Equipment/function• Stationary installation on walls and floors• Flexible installation through the use of

lowering device• Can be swivelled vertically and

horizontally for installation with lowering device


Design Submersible mixer with single-stageplanetary gear


Special features• Single-stage planetary gear for adjusting

the propeller speed• Self-cleaning propeller• Easy-to-install propeller attachment• Propeller in steel, PUR or PUR/GFK version• ATEX and FM versions• 1.4462 gear shaft• Type “TRE” with IE3 performance

optimised motors (derived from IEC 60034-30)

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Protection class: IP 68• Max. fluid temperature: 40 °C• Single-stage planetary gear• Mechanical seal with SiC/SiC combination• Permanently lubricated anti-friction


Equipment/function• Stationary installation on walls• Flexible installation through the use of

lowering device• Can be swivelled horizontally for

installation with lowering device• Installation with stand allows free

placement in basin• Single-stage planetary gear


Design Slow-running submersible mixer withtwo-stage planetary gear


Special features• 2-stage planetary gear for adjusting the

propeller speed• Self-cleaning propeller• Propeller blades can be replaced

individually• Easy-to-install blades and hub• Propeller in GFK version• ATEX and FM versions• 1.4462 gear shaft• “TRE” type with high performance

motors according to IE3 (derived from IEC 60034-30)

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Protection class: IP 68• Max. fluid temperature: 40 °C• Two-stage planetary gear with

exchangeable second planetary stage• Mechanical seal with SiC/SiC combination• Permanently lubricated anti-friction


Equipment/function• Installation with stand allows free

placement in basin• Flexible installation• Two-stage planetary gear with

exchangeable second planetary stage


DesignSubmersible mixers with housing unit,direct driven (RZP 20 …, RZP 25-2 … RZP40...) or with 1-stage planetary gear(RZP 50-3 …, RZP 60-3 …, RZP 80-2 …)

Q max.6,800 m³/h

H max.1.1 m

Special features• Submersible• Vertical or in-line design• Self-cleaning propeller, partially with

helix hub• Propeller in steel or PUR version• ATEX and FM versions

Technical data• Mains connection: 3~400 V, 50 Hz• Immersed operating mode: S1• Protection class: IP 68• Max. fluid temperature: 40 °C• Units are directly driven or with

singlestage planetary gear• Mechanical seal with SiC/SiC combination• Permanently lubricated anti-friction


Equipment/function• Stationary installation directly on flow pipe

• Flexible installation through the use of lowering device

• Vertical or in-line installation possible



13

Design Glandless circulation pump with threaded connection, EC motor and automatic power adjustment.

Q max. 4 m³/h

H max. 6.0 m

Special features • Energy efficiency class A• High-efficiency pump especially for single

and two-family houses, as well as for two to six-family houses.

• Up to 90 % electricity savings compared to old uncontrolled heating pumps

• Only 3 watts min. power consumption• Very high starting torque for reliable

starting• Integrated motor protection• Venting routine for automatic venting

of the rotor chamber

Technical data• Fluid temperature +2 °C to +110 °C• Mains connection 1~230 V, 50 Hz• Protection class IP X4D• Threaded connection Rp ½, Rp 1 and Rp

1¼• Max. operating pressure 10 bar

Equipment/function • Control mode: Δp-c and Δp-v, Dynamic

Adapt control function combinied with Δp-v

• Automatic setback operation• Automatic venting routine• Automatic deblocking function• Red-button technology for simple

operation• Display indication of current power

consumption in W and accumulated electricity consumption in kWh

• Reset function for resetting the electricity meter

• Reset function for resetting to the factory settings

• Blocking current-proof motor• Particle filter• Quick electrical connection with Wilo-

Connector• Options: - Design with bronze pump housing for

use in underfloor heating systems, - Versions with short port-to-port length

130 mm


Design High-efficiency inline pump with EC motor and electronic duty adaptation in glanded construction. Version as singlestage low-pressure centrifugal pump with flange connection and mechanical shaft seal.

Q max. 44 m³/h

H max. 52 m

Special features• Innovative high-efficiency pump for

the highest overall degrees of efficiency based on a new Wilo glanded design

• High-efficiency EC motor (degrees of efficiency above IE4 limit values acc. to IEC TS 60034-31 Ed.1)

• New hydraulics optimally adapted to the EC motor technology

• Integrated electronic power adjustment• Extremely compact and space-saving

design• Simple operation by tried-and-tested

red-button technology and display• Various control modes Δp-c, Δp-v, PID

and n-const. (control mode)• Control range up to three times greater

than in conventional electronically controlled pumps



• Integrated dual-pump management with efficiency-optimised peak-load cut-in

Technical data • Permitted temperature range of the fluid

-20 °C to +140 °C• Mains connection:

3~440 V (±10 %), 50 Hz/60 Hz 3~400 V (±10 %), 50 Hz/60 Hz 3~380 V (-5 %/+10 %), 50 Hz/60 Hz

• Protection class IP 55• Max. operating pressure 16 bar to +120

°C, 13 bar to +140 °C

Equipment/functionSingle-stage, low-pressure centrifugal pump in in-line design with• Mechanical seal• Flange connection• Lantern• Coupling• EC motor with electronic power

adjustment

Materials:• Pump housing and lantern: EN-GJL-250• Impeller: PPS-GF40• Shaft: 1.4122• Mechanical seal: AQ1EGG Other

mechanical seals: on request

InformationOnline catalogue www.wilo.comBuilding Services catalogue, Heating,Air- Conditioning, CoolingWe are continually adding to this series.


Q max. 170 m³/h

H max. 30 m



• Energy savings due to integrated electronic power control

• Simple operation with red-button technology and display

• Various control modes Δp-c, Δp-v, PID and n-const. (control mode)



• Integrated dual pump management• Integrated full motor protection (PTC




3~400 V, 50 Hz; 3~380 V, 60 Hz

• Protection class IP 55• Nominal diameter DN 32 to DN 80• Max. operating pressure 10 bar (special

version: 16 bar)

Equipment/function Single-stage, low-pressure centrifugal pump in in-line design with• Mechanical seal• Flange connection• Motor with integrated electronic speed

control• DP-E with switchover valve

Materials:• Pump housing and lantern: EN-GJL-250• Impeller: PPO-GF30• Shaft: 1.4021• Mechanical seal: AQEGG Other mechanical seals: on request



Q max. 680 m³/h

H max. 65 m

Special features • Motors with IE2 technology for higher

efficiency fitted as standard• Energy savings due to integrated

electronic power control• Simple operation with red-button

technology and display• Various control modes Δp-c, Δp-v, PID

and n-const. (control mode)• Analogue interfaces 0-10 V, 2-10 V, 0-20

mA, 4-20 mA• Optional interfaces for bus

communication using plug-in IF-Modules• Integrated dual pump management• Integrated full motor protection (PTC




3~400 V, 50 Hz; 3~380 V, 60 Hz

• Protection class IP 55• Nominal diameter DN 40 to DN 80• Max. operating pressure 16 bar

Equipment/functionSingle-stage, low-pressure centrifugalpump in in-line design with• Mechanical seal• Flange connection• Lantern• Coupling• Engine with integrated electronic power

adjustment• DL-E with switchover valve

Materials:• Pump housing and lantern: EN-GJL-250• Impeller: Standard version: EN-GJL-200 special version: G-CuSn 10• Shaft: 1.4122• Mechanical seal: AQEGG Other mechanical seals: on request



Glandless Premium high-efficiencypumpsSeriesWilo-Stratos PICO

Glanded high-efficiency pumps inin-line designSeriesWilo-Stratos GIGA

Glanded energy-saving pumps inin-line designSeriesWilo-VeroLine-IP-EWilo-VeroTwin-DP-E

Glanded energy-saving pumps inin-line designSeriesWilo-CronoLine-IL-EWilo-CronoTwin-DL-E

Product category

Food & Bev Quarry & Mining Utilities Power &

Generation Manufacturing Pharma

Booster Set’s

¸¸¸ ¸¸ ¸¸¸ ¸¸¸ ¸¸¸ ¸¸

Submersible

¸ ¸¸¸ ¸¸¸ ¸¸ ¸ ˚

Borehole

¸ ¸¸¸ ¸¸¸ ¸ ¸ ˚

Split Case

¸ ¸¸¸ ¸ ¸¸¸ ¸ ¸

End Suction

¸¸ ¸¸¸ ¸ ¸¸¸ ¸¸¸ ¸¸¸

Mixers

˚ ¸¸ ¸¸¸ ¸ ˚ ˚

Vertical Turbine

˚ ¸¸ ¸¸¸ ¸¸¸ ˚ ˚

In-Line

¸¸¸ ¸¸ ¸¸ ¸¸ ¸¸¸ ¸¸¸

Vertical Multistage

¸¸¸ ¸¸ ¸¸ ¸¸¸ ¸¸¸ ¸¸¸

¸¸¸ : Extensive Use ¸¸ : Regular Use ¸ : In'Fequent Use ˚ : Very Rare

Application Analysis

High competence for water and sewage.

Clean water is becoming increasingly scarce. This makes the sourcing and transportation of valuable water a ceaseless challenge. In view of the variety of sources, e.g. desalinated seawater or aquifers, treatment systems must be more flexible to meet the different compositions of the water. Pumps and components from Wilo are able to supply the fluid for as efficiently and for as long as possible in the best possible way.

When it comes to environmental protection and preserving natural resources, sewage disposal and sewage treatment play an important part. Ongoing challenges such as the increasing content of solid in sewage which makes operating conditions for plants and equipment more difficult create a need for innovative approaches.

Wilo offers the right solution for any application: with the highest safety standards and lowest cost.

3

Founded in 1872 as Kupfer- und Messingwarenfabrik Louis Opländer, the company has almost 70 branches worldwide and over 6,200 employees Turnover amounted to 1,021.4 million EUR in 2010. International recognition has increased rapidly since the company became a European limited liability company (SE) in 2008. Wilo pumps and systems set global standards for efficiency and technical performance: with high-efficiency solutions for all applications in the segments.

World Leading.WILO SE, with headquarters in Dortmund, is one of the world’s leading manufacturers of pumps and pump systems for heating, air conditioning and cooling technology, as well as for water supplies and sewage treatment and disposal.

WILO UK LimitedCentrum 100, Second Avenue

Burton on Trent, Staffs DE14 2WJT +44 (0) 1283 523000F +44 (0) 1283 523099

[email protected]

Wilo IrelandUnit B1, Corcanree Business Park

Dock Road, Limerick, IrelandT: +353 (0)61 227566F: +353 (0)61 229017

[email protected]

“I plan with Wilo because they know about the future.”

Range Guide.Water Management.

pumps macerators and aerators - range guide. water management… · 2019. 10. 21. · online...

Documents