p.t.s conveyor idlers cc is committed to benefiting their conveyor idlers catalogue.pdf · p.t.s...
TRANSCRIPT
P.T.S Conveyor Idlers cc is committed to benefiting their valued clients through:
- An unwavering commitment to supply a quality product and value added service.
- Technical expertise and advisory services.
- Reliability and consistency of supply.
- Product development
- Customised solutions and demand planning
- Excellent Customer Service
QUALITY POLICY
IT IS THE POLICY AND OBJECTIVE OF PTS CONVEYOR IDLERS ccTO MAINTAIN AN EFFECTIVE QUALITY MANAGEMENT
SYSTEM BASED ON SABS ISO 9001.
THE POLICY OF PTS CONVEYOR IDLERS ccIS TO PROVIDE THEIR CUSTOMERS WITH PRODUCTS CONFIRMING
TO THE REQUIRED QUALITY, AND MAINTAIN BEST DELIVERY,SERVICE TO MEET THEIR SPECIFICATION REQUIREMENTS.
THE MANAGEMENTS PHILOSOPHY IS THAT QUALITYIS OF THE UTMOST IMPORTANCE AND THUS, I, AND
ALL EMPLOYEES ARE HEREBY COMMITTED TOPRODUCING QUALITY PRODUCTS, AND TO OPERATE
IN ACCORDANCE WITH THE P.T.S. CONVEYOR IDLERS ccQUALITY MANAGEMENT SYSTEM AS DEFINED IN THE
QUALITY POLICY AND QUALITY PROCEDURES MANUAL.
P.T.S Conveyor Idlers cc.128 Craig rd, Anderbolt, Boksburg North.
Tel. 011 894 6767 | Fax. 011 894 6738Website. www.ptsidlers.co.za
Managing Member Brian Lindsay
Tel. 083 298 7668
Managing Member Gys vd WesthuizenTel. 083 280 4647
E-mail. [email protected]
Financial Manager Marinda vd Westhuizen
Tel. 083 564 6602E-mail. [email protected]
Sales Manager Steven Jordaan
Tel. 083 408 0645E-mail. [email protected]
Copyright of these Drawings is the property of P.T.S Conveyor Idlers cc. Making a copy of them or making the products or parts shown in them for any purpose other than for which they have come into your legitimate possession or without the express written permission of P.T.S Conveyor Idlers cc. will constitute infringements of the Copyright Law and shall
lead to prosecution.
IndexItem. Page.CONVEYOR BELT TROUBLE SHOOTING 02 - 03
STANDARD ROLLER DIAGRAM 04
TUBULAR :
3 ROLL TUBULAR TROUGH 127 X SERIES 25 05
3 ROLL TUBULAR IMPACT IDLER 152 X SERIES 25 06
2 ROLL TUBULAR VEE RETURN 127 X SERIES 25 07
ANGULAR
3 ROLL ANGULAR TROUGH 127 X SERIES 25 08
3 ROLL ANGULAR IMPACT IDLER 152 X SERIES 25 09
2 ROLL ANGULAR VEE RETURN 127 X SERIES 25 10
RETURN ROLLERS :
CARRY ROLLER 127 X SERIES 25 11
FLAT RETURN ROLLER 127 X SERIES 25 12
TUBULAR UNDERGROUND STRUCTURES :
3 ROLL ADJUSTABLE STRUCTURE 13
UNDERGROUND RETURN ROLLER 127 X SERIES 25 14
3 ROLL TUBULAR U.G FRAME 127 X SERIES 25 15
Copyright of these Drawings is the property of P.T.S Conveyor Idlers cc. Making a copy of them or making the products or parts shown in them for any purpose other than for which they have come into your legitimate possession or without the express written permission of P.T.S Conveyor Idlers cc. will constitute infringements of the Copyright Law and shall
lead to prosecution.
BELT BOWED – Avoid telescopic belt rolls or storing them in damp locations. *A new belt should straighten
BELT IMPROPERLY SPLICED OR WRONG FASTERNERS - Use correct fasteners. Retighten after running for a short while. If improperly spliced, remove belt splice and make new splice. *Set up regular inspection schedules.
BELT SPEED TO FAST – Reduce belt speed
BELT STRIANED ON ONE SIDE – Allow time for new belt to “break in”. If belt does not break in properly or is not new, remove strained section and splice in a new piece.
BREAKER STRIP MISSING OR INADUQUATE – When is lost, install belt with proper breaker strip.
COUNTERWEIGHT TO HEAVY – Recalculate weight require and adjust counterweight accordingly. * Reduce take-up tension to point of slip, then tighten slightly.
COUNTERWEIGHT TO LIGHT – Recalculate weight required and adjust counterweight or screw take-up accordingly.
DAMAGED BY:ABRASIVES, ACID, CHEMICALS, HEAT, MILDEW, OIL – Use belt designed for specific conditions
DIFFERENTIAL SPEED WRONG ON DUAL PULLEYS -Make necessary adjustment.*
DRIVE UNERBELTED – Recalculate maximum belt tensions and select correct belt. If line is over-extended, consider using two-flight system with transfer point. If carcass is not rigit enough for load, install belt with proper flexibility when service is lost.
EDGE WORN OR BROKEN – Repair belt edge. Remove badly worn ot out-of-square section and splice in a new piece.
EXCESSIVE IMPACT OF MATERIAL ON BELT OR FASTE – Use correctly designed chutes and baffles. Make vulcanized splices. Install loading idlers. Where material is trapped under skirts, adjust skirt boards to minimum clearance or install cushioning idlers to hold belt against skirts.
EXCESSIVE TENSION – Recalculate and adjust tension. Use vulcanized splice within recommended limits.
FROZEN IDLERS – Free idlers. Lubricate. Improve
IDLERS OR PULLEYS OUT OF SQUARE WITH CENTRE LINE OF CONVEYOR – Realign, Install limit
IDLERS IMPROPERLY PLACED – Relocate idler or insert additional idlers spaced to support belt.
IMPROPER LOADING, SPILLAGE – Feed should be direction of belt travel and at belt speed, centered on skirt boards.
IMPROPER STORAGE OR HANDLING – Refer to belting suppliers for storage and handling tips.
INSUFFICIANT TRACTION BETWEEN BELT &PULLEY – Increase wrap with snap pulleys. Lag drive pulley. In wet conditions, use grooved lagging. Installcorrect cleaning devices for safety. See item 7 on the next page.
MATERIAL BETWEEN BELT AND PULLEY – Use Skirt boards properly. Remove accumulation. Improve maintenance.
MATERIAL BUILD UP – Remove accumulation. Install cleaning devices, scrapers, and “V” decking. Improve housekeeping.
PULLEY LAGGING WORN – Replace worn pulley lagging. Use grooved lagging for wet conditions. Tighten loose and protruding bolts.
PULLEY TO SMALL – Use larger diameter pulleys
RADUIS OF CONVEX VERTICAL CURVE TOO SMALL – Increase radius by vertical realignment of Idlers to prevent excessive edge tension.
RELATIVE LOADING VELOCITY TOO HIGH OR TOO LOW – Adjust chutes or correct belt speed. Consider use of loading idlers.
SIDE LOADING – Load in direction of belt travel, In center of conveyor.
SKIRTS IMPROPERLY PLACED – Install skirt boards so that they do not rub against belt.
1.)
2.)
3.)
4.)
5.)
6.)
7.)
8.)
9.)
10.)
11.)
12.)
13.)
14.)
15.)
16.)
17.)
18.)
19.)
20.)
21.)
22.)
23.)
24.)
25.)
26.)
27.)
P.T.
S C
onve
yor I
dler
s cc
Tel.
011
894
6767
Fax.
011
894
673
8w
ww.
ptsid
lers
.co.za
128
Cra
ig ro
ad
Boks
burg
Nor
th15
08