ptrx 7300 alternative installa tion guide for full hf … · your conta m ndwidth icom ic‐730 r...
TRANSCRIPT
This d
instan
the d
the ri
PTRX‐
rear p
to an This i
1 2 3 4
1 2
document des
ntaneous HF b
default J1431 lo
g.
‐7300 enables
panel. This 50
SDR.
nstallation is s
1. PTRX‐7300
2. TMP‐MCX R
3. 4‐pin/4‐ pin
4. SMA‐MCX R
Installation
1. Remove th
2. PTRX‐7300
upward an
tuner conn
PRODUCT R
PTRX‐73
scribes alterna
bandwidth. Thi
ocated in the
to extend inte
Ohm output ca
olderless and r
Panadapter M
RG‐174 Cable A
n PH2.0 Tuner
RG‐174 Cable A
n Instructions
e top cover of
Panadapter M
d seperate it t
ection after in
REGISTRATIONEMAIL US P
300 ALTERNAT
ative installatio
s result is ach
“RF board” of
ernal received
an be used to
reversible. The
Module
Assembly
Cable Assemb
Assembly
the IC‐7300.
Module is inst
ogether with i
stalling PTRX‐7
N: REGISTER YOP/N CODE ON T
TIVE INSTALLA
on of PTRX‐73
ieved by samp
the radio. Thi
RF signals of I
monitor high r
e kit is compos
bly
Fig
alled in place
ts cable assem
73 00 Panadap
OUR PRODUCTTHE BACK OF Tradioanalogi
1
ATION GUIDE F
300 Panadapte
pling the signa
is configuratio
IC‐7300 by exp
resolution, wid
ed by the follo
gure.1 Part List
of the tuner
mbly from the r
pter Module.
T TO START YOTHE PCB [email protected]
FOR FULL HF BA
er Module for
al from anothe
n actually byp
posing a stand
deband spectru
owing items:
t
connector on
rig. This cable
OUR WARRANTH YOUR CONTAom
ANDWIDTH
r ICOM IC‐730
er tap point (J1
passes the inpu
art 50 Ohm ou
um of receive s
the rear pan
assembly will
TY AND TECHNACT DETAILS T
00 radio to ge
1071) rather th
ut band select
utput connecto
signals via con
el. Slide the c
be used as the
NICAL SUPPORO
t the full
han using
filters of
or on the
necting it
connector
e external
RT
Fi
Figure.3
igure.2 Extern
3 External Tune
2
nal Tuner conne
er connector in
ector
nternal view
GentlPH2.0
ly remove the0 Tuner Cable A
connector froAssembly (Fig.
om J331 taking1 Part list, Item
F
Fiure.4 J3
g it aside for lm #3) to it and
Figure.5 PH2.0
3
31 Connector
later use. Taketo the J331 co
0 Cable Connec
e the PTRX‐73onnector as sho
ction
00 board and own in Figure 5
attach the 4‐5.
pin/4‐pin
Carefconn
fully unplug thector CN1.
he original cab
Figure.6 Unp
ble going to IC
plugging the or
Figure.7 Conn
C‐7300 J1071 c
riginal cable o
nection betwee
4
connector (ins
n J1071 and co
en j1071 and P
side red circle
onnecting to P
PTRX‐7300 Boa
e) and place it
PTRX‐7300 Boa
ard
t to PTRX‐7300
ard
0 board
Connand t Now
This i
nect the TMP‐Mto IC‐7300 rad
slide the PTRX
is the result af
MCX RG‐174 Cdio connector J
X‐7300 board
fter mounting
Cable AssembJ1071 (type TM
to the rear pa
Fi
g the upper co
Figure.9
ly (Fig.1 Part lMP) keeping
anel checking
igure.8 Placing
ver of the Ico
9 External view
5
ist item #2) toattention to m
that all conne
g PTRX‐7300 B
m IC‐7300, sh
w of Rear Pane
o PTRX‐7300 bmate the corre
ections are pro
Board
own in Figure
el Interface
board connectect connector
operly fixed a
e.9.
tor CN3 (type . Shown in Fig
nd routed.
MCX) gure.7.
The olist, it
Pana Discla
original tuner tem #4) has to
dapter is now
aimer: We are
cable assembo be finally co
w ready to use.
e not liable for
Figure.10 Con
ly could eventnnected to th
. For further in
r any damage
nnections to R
tually be re‐cohe MCX conne
nformation vis
to your equip
6
RF port and Ext
onnected. Theector of the PT
sit www.radio
pment caused
ternal Tuner Po
e SMA‐MCX RTRX‐7300 boa
oanalog.com
by using this e
ort
RG‐174 Cable Ard and to the
extention. Use
Assembly (FigSDR receiver.
e it at your ow
g.1 Part
wn risk.