providing engineering solutions for waterproofing and ... · providing engineering solutions for...
TRANSCRIPT
Providing Engineering Solutions for Waterproofing and Concrete Repair Projects
www.ardexendura.com
Product Name
Application Areas
WPM 300 Multipurpose primer for all liquid applied membranes, moisture barrier coating, dust suppressor & also waterproofing for potable water tanks, etc.
WPM 004 Showers, kitchens, bathrooms, wet areas and under tile protective membrane / terrace, etc.
WPM 002 Internal and external wet areas, swimming pools, water tanks, balconies / podiums / terrace / decks and other areas that will be tiled or otherwise protected from regular foot traffic, etc.
WPM 124 Kitchen, toilets, balconies, wet areas, walkways, terraces, planter boxes, protected situation like roof and decks, lift pits, etc.
WPM 415 C Basements, retaining walls, wet areas & balcony / roof terrace areas, etc.
WPM 310 External walls in residential buildings, apartments buildings, hotels, malls commercial buildings, etc.
WPM 401 C Stop active water leaks in basement, tunnels, potable water tanks and voids around pipes, etc.
WPM 256 Bonding Bridge, pore sealer, epoxy admixture, dust suppressor, etc.
C 10 Shuttering oil, steel shuttering, wood shuttering & mivan shuttering, etc.
C 20 Green concrete substrates like, slabs, columns, pillars, plastering, basements & RCC, etc.
E 135 Slurry bond coat for plastering, admixture for cement sand mortar, fillets coving & bonding agent for cold joint, etc.
EP 310 Anchoring reinforcement bars, dowels, holding down bolts, base plates, etc.
EP 300 Bonding agent for old & new concrete tiles and bricks, concrete blocks, repairing pot holes, spalled concrete & rehabilitation structures, etc.
EP 410 Reinforcement bars, exposed rebars, exposed iron surface, etc.
B 30 Structural grout, base plates, bore packing, tie rod fixing & bulk filling in concrete repair, etc.
B 40 Repairing damaged concrete, columns and cross beams on structures, below ground constructions, foundation support, retaining walls, etc.
B 35 Repairing and refacing internal concrete - stair treads and risers, cement and sand screeds, concrete floors, patching concrete repair works, etc.
B 33 Repairing damaged concrete, deteriorated concrete, etc.
EP 320 Crack injection for 0.1mm-10mm, RCC walls, control joints, vertical crack injection for concrete floors, rigid crack treatment & rehabilitation structures, etc.
EP 325 High viscous crack injection for 0.5mm -10mm, control joints, vertical crack injection for concrete floors, RCC walls, rigid crack treatment & rehabilitation structures, etc.
SU 10 Expansion joints, crack treatments, Bond breaker, joint filler for dry walls, window frames, etc.
AC 40 Rendered walls, bricks/masonry walls, fibre cement sheets, tilt up and pre-cast concretes, light weight aerated concrete blocks, etc.
B 50 Industrial grout, machinery base plates, pot hole filling in industries with chemical spillages & bore pack in chemical drains/tanks, etc.
4
Page No.
5
6
7
8
9
Wat
erpr
oofin
gCon
cret
e Re
pair
& A
ncillar
ies
ARDEX
- A Global Perspective
ARDEX ENDURA (INDIA) PVT LTD is a joint venture between ARDEX Group, Germany and Prism Cement Limited, India. Both the partners
hold 50% each of the Share Capital of the Company. Initially, the Company was incorporated with the equity and technology
participation by Norcros Group based in UK. Ardex Group acquired the adhesive division of Norcros Group in 2001. As a result, AEIPL
came to be associated with ARDEX Group of Germany and the name of the Company was changed in line with this.
With the guidance & full support from the ARDEX Group, ARDEX ENDURA
remains the quality leader for the entire industry, offering excellent
building chemicals with supreme processing reliability. With manufacturing
plants at Bangalore & Baroda & with 30 active branches all over India,
ARDEX ENDURA manufactures products you can trust and rely on. Our
expert technical team is available for on-going support at every stage of
construction, from rapid response to specification writing, to installation
visits and on-site testing.
ARDEX ENDURA is the brand of choice for Architects, Engineers,
Contractors, Masons…… in fact for everybody associated with the Building &
Construction industries.
Our company's heritage dates back more than 60 years and, as a global manufacturer of high performance speciality building materials, ARDEX has remained at forefront of the world's leading supplier's for the building & construction industries.
The ARDEX name has been synonymous with innovative, premium quality products and services globally for many decades.
Our vision is to be one of
The World's Leading Solution Providers
of High Performance Specialty
Building Materials
Building Materials Technology by ARDEX GmbH, Germany
Baustofftechnologie präsentier t von ARDEX GmbH, Deutschland
Delhi
AhmedabadIndore
Mumbai
Goa
Calicut
Ernakulam
Ludhiana
Hyderabad
Chennai
Trivandrum
Pune
Raipur
LucknowJaipur
Salem
Vijayawada
Bangalore
Vadodara
Mangalore
Aurangabad
Hubli
Bhubaneshwar
Tirchy
GuwahatiPatna
Ghaziabad
Kolkata
Shimoga
Mysore
Vishakapatnam
30 BRANCHES
2 RUNNING PLANTS
1 UP COMING PLANT
Profile
ARDEX Global
CONCRETE REPAIR & ANCILLARIES
BEFORE AFTER
TILE & STONE CARE
TILE ADHESIVES & GROUTS
FLOORING SYSTEMS
WATERPROOFING SYSTEMS
3
Waterproofing
Features
?Two component elastomeric waterproofing system
?Advanced acrylic based
?Protect the concrete from long term weathering and resists UV rays
?Water based - safe to use, low odour & easy cleaning
?Suitable for all cementitious substrates
WPM 004 Two Component Acrylic Modified Flexible Cementitious Waterproof Coating
WPM 004 is a two component waterproof coating specifically designed for under tile protective membrane and on roofs as exposed membrane. WPM 004 is flexible, safe to use, low in odour.
The products have been uniquely formulated with special polymer to increase its strength. WPM 004 is based on the most advanced acrylic polymer technology and is totally resistant to re-emulsification.
Application AreasShowers, kitchens, bathrooms, wet areas & under tile protective membrane / terrace, etc.
Pack size Coverage20kg Approximately 14 m² per pack @ 0.8 mm - 1.0 mm Part A 5 litres thickness for two coats by roller / brushPart B 15kg
4kg Approximately 2.5 m² per pack@ 0.8 mm - 1.0 mmPart A 1 litre thickness for two coats by roller / brushPart B 3kg
Features
?Rapid drying time
?Two component undertile waterproofing membrane
?Advanced acrylic – will not re-emulsify
?Liquid reinforced – eliminates the need for reinforcing mat
?Meets class III category for AS4858 Wet Area Membranes
?Low VOC content – meets Green Building Council of Australia Green Star IEQ-13 requirements
WPM 002 Two Component Undertile Waterproofing Membrane
WPM 002 is a tough, fast drying two component waterproofing membrane specifically designed for use under tiles. The product has been uniquely formulated with synthetic microfibres to increase its strength and eliminate the need for a separate reinforcement mat. WPM 002 is based on the most advanced acrylic polymer technology, and is totally resistant to re-emulsification.
WPM 002 is flexible, low in odour, and is fully compatible with polymer modified tile adhesives. WPM 002 is one of the fastest drying acrylic membranes on the market - normally ready to tile in 16 - 24 hours @ 23°C.
Application AreasInternal and external wet areas, swimming pools, water tanks, balconies / podiums / terrace / decks and other areas that will be tiled or otherwise protected from regular foot traffic, etc.
Pack size Coverage40kg Two coats are recommended for an effective waterproof Liquid: 20 Litres membrane. One 40 kg kit will cover approximately Powder: 20kg 16 - 24m² (based on two coats) depending on area
requirements between wall and floor surfaces to be treated.
Features
?Water resistant, prevents rising damp, efflorescence and withstands hydrostatic pressure
?Excellent adhesion to most substrates including damp surfaces and freshly laid green concrete
?Safe to use in sensitive locations
WPM 300 Water Based Epoxy Membrane
WPM 300 is a two component water based epoxy polyamide membrane/ barrier coating.
Approved for use with potable (drinking) water, independent testing confirms conformity with the requirements of AS4020.2000 and BS6920.
Application AreasMultipurpose primer for all liquid applied membranes, moisture barrier coating, dust suppressor & also waterproofing for potable water tanks, etc.
Pack size Coverage20 Litres Must be applied at a rate of 1.5 square metres Part A 10 Litres per litre (3.0 square metres per litre per coat) Part B 10 Litres to achieve an effective waterproofing membrane
Features
?Single component - ready to use
?Can be applied by brush or roller
?Quick drying
?Elastomeric seamless membrane
?Able to bridge cracks
?Can be painted over with good quality acrylic paint
?Water - based & Environment friendly
WPM 124 Single Component Liquid Waterproof Membrane
WPM 124 is a single component, ready-to-use, liquid applied waterproof membrane. WPM 124 comprises of special blend of copolymers and additives to provide an excellent and quick - drying waterproofing membrane.
Application AreasKitchen, toilets, balconies, wet areas, walkways, terraces, planter boxes, protected situation like roof and decks, lift pits, etc.
Pack Size Coverage20kg Approximately 0.4 kg/m²/coat (WFT) / coat
approx. 0.4 ± 0.1mm
4
Features
Flexible - accommodates normal building movement?
?Provides excellent UV resistance and long term protection from elements
?Excellent workability – easy, quick to apply
?Decorative – choice of colours
?Water based – safe to use, low odour and easy cleaning
WPM 310 External facade & Roof membrane
WPM 310 is a tough, UV stable flexible, premixed liquid applied waterproofing membrane. It has been specifically formulated as a general purpose membrane for exposed wall and roof waterproofing. WPM 310 can be applied as an aesthetically attractive textured or semi-smooth finish for walls or a semi-smooth uniform finish for roofs. WPM 310 is available in a range of standard colours.
Application AreasExternal walls in residential buildings, apartments buildings, hotels, malls & commercial buildings, etc.
Waterproofing
Application AreasBasements, retaining walls, wet areas & balcony / roof terrace areas, etc.
Features
?Suitable for sewage treatment and water treatment plant, water tanks, concrete pipes and manholes
?Deeply penetrates and seals the substrate
?Single component system, no addition of liquid component except water at site
?Suitable for external and internal application
?Toxic free - Providing protection against corrosive waterborne salts
WPM 415 C Crystalline Capillary Waterproofing
WPM 415 C is a single component polymer modified cementitious waterproofing compound. The mixed slurry as excellent adhesion with concrete / sand cement screed. During application it seals the hairline cracks caused by shrinkage or expansion.
Pack size Coverage20kg Approximately 13 - 16.50m² per two coats @ 150 - 200
microns thickness
Pack size Coverage15 Litres External wall membrane application
1 x 15 litres unit will cover approximately 24 square metres in two coats at a total dry film thickness of 0.3 mm.
Roof membrane application1 x 15 litres unit will cover approximately 7 square metres in two coats at a total dry film thickness of 1.0 mm. Coverage will vary depending on the condition of the surface and film thickness.
Features
?Water leakage stopping capability
?Very good bonding to the cementitious substrate
?Ideal for use onto horizontal / vertical surfaces and against gravity
?Single component, add required amount of clean water at the site
?For internal and external situations
?No curing required
Features
?Penetrating Structural Sealer
?Forms a structural bond between new and old concrete
?Can be applied to damp surfaces
?Compatible with fresh cement or concrete products
?Excellent adhesion to most substrates
WPM 401 C Rapid Setting Cement Based Water Stopping Mortar
WPM 401 C is a specially blended, extremely fast setting, hydraulic cement product designed to instantly stop leaking water or fluid seepage in concrete or masonry structures. When WPM 401 C is mixed with water, it controls the rate of setting time and minimise the risk of thermal cracking. The mixed material sets in 1 minute.
WPM 256 Water Based Epoxy Bonding Bridge
WPM 256 is a two component water based epoxy polyamide unpigmented new to old concrete bonding bridge and admixture for cement based materials and structural penetrating sealer.
Application AreasStop active water leaks in basement, tunnels, potable water tanks and voids around pipes, etc.
Application AreasBonding Bridge, pore sealer, epoxy admixture, dust suppressor, etc.
Pack size Yield10 kg The yield per 10kg bag is approx. 5.50 litres.
PACK SIZE20 Litres Part A: 10 LitresPart B: 10 Litres
5
Features
?Water based, environmentally friendly
?It reduces damage
?Suitable for all types of shutters and moulds
?Fast working progress
?Stain free
?Easy application
C 10 Mould Release Emulsion
C 10 is specially designed for the release of hardened concrete from the mould and shutters. It forms a thin water repellent layer on the surface of the formwork and prevents the concrete from adhering. C 10 is water based, environmentally friendly and technically superior to typically found oil based products. The reactive components in C 10 protect the formwork and ensure an even colour and texture in the cast concrete.
Application AreasShuttering oil, steel shuttering, wood shuttering & mivan shuttering, etc.
Pack size Coverage5 Litres Approximately 60 - 100 m²/litre when diluted with 20 Litres 1 : 3 water200 Litres
CONCRETE REPAIR & ANCILLARIES
Features
?Single component
?Minimises the surface cracks
?Ease of curing the fresh concrete, UV exposed concrete / mortar surface
?Reflects UV rays
?Provides good curing efficiency
?Toxic free and biodegradable
C 20 Concrete Curing Compound
C 20 is a liquid emulsion, which when used on fresh concrete / mortar surface, seals the concrete surface temporarily and prevents rapid moisture evaporation from the concrete. It forms a thin layer for the complete curing period and improves the durability of the concrete. Suitable for all construction applications and highly beneficial for malls, flyovers, bridges, airports, dams, etc., or anywhere where water curing may be difficult.
Application AreasGreen concrete substrates like, slabs, columns, pillars, plastering, basements & RCC, etc.
Pack size Coverage5 Litres Approximately 6m² /litre /coat 20 Litres200 Litres
Features
?High performance polymer additive for cement and concrete mixes
?Ideal for patching, can be feathered out to repair cracks and also for use in coving
?Non-toxic - does not create occupational health & safety concerns
?Good workability and consistency
E 135 Admixture and Polymer Bonding Agent (SBR)
E 135 is an SBR, multipurpose, concentrated, liquid polymer additive which when used with sand/cement, greatly improves the workability and consistency. It can also be used as an admix for renders / screeds creating workability and consistency. E 135 can be applied to damp surfaces (Saturated Surface Dry no standing water) and can be rendered or painted over.
Application AreasSlurry bond coat for plastering, Admixture for cement sand mortar, fillets coving & Bonding agent for cold joint, etc.
Pack size1 Litre5 Litres20 Litres.
Features
?High strength
?Tough, shrink-free & strong anchoring system
?Vibration resistance
?Resistance to heavy loads
?Corrosion resistance
?Easy to apply
EP 310 Polyester Resin Anchoring Grout
EP 310 is a specialist anchoring grout which combines, outstanding durability and anchoring properties. This anchoring grout is stronger than the concrete. It is used for anchoring reinforcing bars, dowels & holding down bolts. It can be used in a gap range of 5 - 25mm, for a depth up to 750mm and also used to repair larger voids-where fast strength gain is important.
Application AreasAnchoring reinforcement bars, dowels, holding down bolts, base plates, etc.
Pack size Yeild1kg The approximate yield per 4kg pack is 2.1 litresPart A : 250gPart B : 750g
4kgPart A : 1kgPart B : 3kg
6
Features
?Excellent bond strength
?Non-Shrink
?Forms a structural bond between new and old concrete
?Can be applied to damp surfaces
?Compatible with fresh cement or concrete products
?Excellent adhesion to most substrates
EP 300 Epoxy Bonding Agent
EP 300 is an un-pigmented two component, polyamide epoxy bonding agent. It is specifically designed for bonding new render or concrete to aged or old concrete substrates. It acts as a high strength bonding bridge between old and new concrete. EP 300 is a good bonding agent for tiles, bricks, concrete blocks, repairing potholes and spalled concrete etc.
Application AreasBonding agent for old & new concrete tiles and bricks, concrete blocks, repairing pot holes, spalled concrete & rehabilitation structures, etc.
Pack size Coverage5kg Approximately 10m²/kit @ 250 micronsPart A 4kgPart B 1kg
Features
?Good adhesion to the steel reinforcement
?Can be applied on exposed reinforcement steel surface for use with ARDEX ENDURA repair mortors
?Easy to apply
?Corrosion resistant
EP 410 Two Component Epoxy Zinc Rich Primer
EP 410 is a two component system based on metallic zinc and epoxy resin for priming reinforcement steel for use with repair mortar. The product resists the corrosion within the repair locations.
Application AreasReinforcement bars, exposed rebars, exposed iron surface, etc.
Pack size Coverage 5 Litres Approximately 4.50m² per coat/litre @ 100 micron
Part A 4 Litres thicknessPart B 1 Litre
Features
?Shrink-free
?Strong
?Simply add required quantity of water
?Can be used at flowable or pourable consistency
?Chloride free
?Non-staining
?Can be applied by pump
?High compressive strength
?Excellent performance
B 30 Single Component Shrink-free Structural Grout
B 30 is an advanced, virtually tension free cementitious structural grout. It is a grey cement based powder with suitable size of aggregates and powder additives. The flowable consistency can be achieved by adding required amount of clear water to B 30. This flowable grout can be applied for gap width of minimum 10 mm.
Application Areas Structural grout, base plates, bore packing, tie rod fixing & bulk filling in concrete repair, etc.
Pack size Yield25kg The approximate yield per 25kg bag + 4.5 litres of water is
13 litres
Features
?Suitable for electro - chemical repairs
?Can be used without primer
?Excellent bond to the concrete substrate
?Less alkali content
?Good strength
?Less permeability provides very good protection against Carbon dioxide and chlorides
?Can be used internal and external situations
B 40 Non Shrink Free Flowing Cementitious Micro Concrete
B 40 is a blend of dry powder which requires only addition of clean water at site. It is used to repair large structural section of concrete and corrosion damage concrete.
Application AreasRepairing damaged concrete, columns and cross beams on structures, below ground constructions, foundation support, retaining walls, etc.
Pack size Yield25kg The approximate yield per 25kg bag + 3.9 litres of water is
12 litres
CONCRETE REPAIR & ANCILLARIES
BEFORE AFTER
7
Features?Good strength
?Slump free - ideal for vertical and horizontal repairs
?Ideal for the repair of internal and external concrete, screeds, renders
?Excellent bond to cementitious substrate
?Shrink free
?No curing required
?Application thickness: - Horizontal 5 - 100mm- Vertical 5 - 15mm
B 35 Two Component Structural Grade Polymer Modified Renovation Mortar
B 35 is a two component, cementitious polymer modified high strength repair mortar with good handling characteristics for internal and external repairs. The hardened material provides excellent thermal compatibility with concrete and outstanding water requirement ensures fast strength gain and long-term durability.
Application AreasRepairing and refacing internal concrete - stair treads and risers, cement and sand screeds, concrete floors, patching concrete repair works, etc.
Pack size Coverage20.20kg Approximately 1 m² @ 10 mm thicknessPart A 20kgPart B 200ml
CONCRETE REPAIR & ANCILLARIES
FeaturesVery good bonding to cementitious substrate
?Slump free - ideal for vertical and against gravity repairs at higher thickness
?Shrink free mortar
?No curing required
?Can be used in internal and external areas
?
?
Application thickness:- Horizontal 5 - 25mm- Vertical 5 - 40mm- Against gravity 10 - 25mm
B 33 Two Component High Build Polymer Modified Cementitious Renovation Mortar
B 33 is a two component, cementitious polymer modified, light weight repair mortar used for repair damaged concrete and deteriorated concrete. It provides high build characteristics as well as good bonding to the concrete.
Application AreasRepairing damaged concrete, deteriorated concrete, etc.
Pack size Coverage20.60kg Approximately 1.3 m² @ 10 mm thicknessPart A 20kgPart B 600ml
Features
?Excellent bond strength
?High elastic modulus ensures effective transfer of stresses at bond interface
?Pre proportioned to give consistent performance
?Due to its low viscosity grouting can be done to air line cracks
?Resistant to a wide range of chemicals and liquids
EP 320 Solvent-free, Epoxy Resin for Crack Injection
EP 320 is a two-component, epoxy resin based crack injection system, designed for sealing cracks in concrete. It is recommended for grouting of 0.10 mm to 10 mm wide cracks, cold joints and other such undesirable cracks.
Low Viscosity
Application AreasCrack injection for 0.1mm-10mm, RCC walls, control joints, vertical crack injection for concrete floors, rigid crack treatment & rehabilitation structures, etc.
Pack size Coverage1kg The coverage depends on the substrate, width of the crack /Part A 750g void to be grouted, loss and waste and porosity of the Part B 250g substrate4kg Part A 3kgPart B 1kg
Features
?Excellent bond strength restores structural integrity
?High elastic modulus ensures effective transfer of stresses at bond interface
?Pre proportioned to give consistent performance
?Moisture-insensitive versatile in applications
?Resistant to a wide range of chemicals and liquids
EP 325 Solvent Free, High Viscous Epoxy Resin for Crack SystemInjection
EP 325 is a two-component, moisture -insensitive, epoxy resin based crack injection system, designed for sealing cracks in concrete and restoring its structural integrity. It is recommended for grouting of 0.5 mm to 10 mm wide cracks, cold joints and other such undesirable cracks.
Application AreasHigh viscous crack injection for 0.5mm -10mm, control joints, vertical crack injection for concrete floors, RCC walls, rigid crack treatment & rehabilitation structures, etc.
Pack size Coverage5 kg The coverage depends on the substrate, width of the crack /Part A 4.10kg void to be grouted, absorption of the substrate, loss and Part B 900gms waste and porosity of the substrate
8
Features
Non staining- Granite, marble, sandstone- Metal frame, perimeter sealing- Various joint sealing of PC and RC- Aluminum
?Expansion joints in heavy and light prefabrication and traditional masonry
?Sealing joints for facade panels, curtain walls, boarding, exterior wood finishing
?Joints between frame and preframe, between door frame and masonry
?Adheres on a majority of building supports: concrete, glass, anodized aluminium, wood...
?
SU 10 Single component, elastomer polyurethane sealant for expansion joints
SU 10 is a single component, elastomer polyurethane sealant for expansion joints.
Application AreasExpansion joints, crack treatments, bond breaker, joint filler for dry walls, window frames, etc.
Pack size CoverageSausage 600ml Applicable joint length with a 600 ml Sausage (in metres)20 sausages per box
CONCRETE REPAIR & ANCILLARIES
Features
External anti-carbonation facade membrane
?Semi-permeable membrane – allows wall surface to breathe
?Contains fungi and algae growth inhibitors
?Provides excellent UV resistance and long term protection from elements
?Water based, safe to use, low odour and easy cleaning
?
AC 40 External Anti-Carbonation Facade Membrane
AC 40 is an extremely weather resistant water based acrylic waterproofing membrane. Specially designed as an exposed facade membrane. AC 40 prevents moisture, chloride ion and carbon dioxide entering and damaging the building structure while still allowing the substrate to breath.
AC 40 is also highly resistant to dirt retention, as well as containing fungi and algae growth inhibitors. The product s flexibility and high build qualities allow it to be applied over hairline cracks.
AC 40 is water based, low in odour and is available in a range of decorative colours.
'
Application AreasRendered walls, bricks/masonry walls, fibre cement sheets, tilt up and pre-cast concretes, light weight aerated concrete blocks, etc.
Pack size Coverage15 Litres Coverage: 1 x 15 litre unit of AC 40 will cover
approximately 21m²²(at a dry film thickness of 0.35mm after two coats).
Features
?High strength
?Resistance to heavy static loads
?Easy to apply
?Shrink free, tough epoxy floor grout system
B 50 Industrial Epoxy Floor Grout
B 50 is specialist applied Industrial Epoxy Floor Grout, combining outstanding wearing properties. It is used for bedding, grouting and void filling operations of gap width of minimum 10mm and also used in areas of equipment bases where chemical spillage occurs.
Application AreasIndustrial grout, machinery base plates, pot hole filling in industries with chemical spillages & bore pack in chemical drains/tanks, etc.
Pack size Yield26.50kg The approximate yield per 26.50kg pack is 13.50 litresPart A 3.30kgPart B 1.725kgPart C 21.475kg
4 6 8 12 20
4 36.7 25.1 18.7 12.5 7.3
6 16.6 12.5 8.3 5.0
8 9.2 6.1 3.6
10 5.0 3.0
Joint width (in mm)
Joint depth
(in mm)
Poly Reinforced Cloth Sealing Tape Ring Type MixerGeo TextileTo
ols
& A
nci
llaries
9
Wat
erpr
oofin
g P
roje
cts
Concrete Repair
Projects
Valued Clientele
Akshaya Homes - Belvedere, Chennai
Ascendas IT park, Pune
B.G.R Power Plant Limited, Nellore
BHEL, Hyderabad
Brigade Group, Bangalore
CICILIA Resorts, Kollam
Doshi Housing, Chennai
ETA Properties, Bangalore
ETA Properties, Chennai
IIBS, New Delhi
ITC Grand Maratha, Mumbai
Jain Housing, Chennai
JW Marriot, New Delhi
KPTCL, Bellary
Mantri Group, Bangalore
Mumbai International Airport, Mumbai
Muthoot Hilton Garden, Trivandrum
N R Green Wood Construction Pvt. Ltd., Bangalore
Novatel, New Delhi
Novotel Project - Salarpuria Grand, Kolkata
Ozone Group, Bangalore
Prestige Estates Projects Limited, Bangalore
Pullman, New Delhi
Purvankara, Ernakulam
Branches
WPM
&CRA
/05/
14
Radiance Realty, Chennai
RDS Projects Limited, Cochin
Samsung Electronics, Noida
Sobha Developers, Bangalore
Sterling Projects, Ernakulam
Sunrise Hospital, Mumbai
The Park, Cochin
True Value Homes, Chennai
West Inn, Mumbai
Yamazaki mazak, Pune
Brigade Exotica, Hoskote
Brigade Meadows, Bangalore
Hospet NH Grade Separator, Hospet
IBIZA Town, New Delhi
LT Karle, Bangalore
Mantri Webcity, Bangalore
NAL, Bangalore
Pashmeena Waterfront, Hoskote
Patel's Reality, Bangalore
Prestige Estates Projects Limited, Bangalore
Salarpuria Group, Bangalore
Sattva Greenage, Bangalore
Wave II, New Delhi
ARDEX ENDURA (INDIA) PRIVATE LIMITEDCORPORATE OFFICE & REGD. OFFICE: Unit No. 406 & 407, “Brigade Rubix”, No. 20, Yeshwanthapur Hobli, HMT Campus, Bangalore - 560022.
CIN No: U24233KA1997PTC022383 Tel: +91 80 66746500 Email: [email protected] Visit us: www.ardexendura.com
?AHMEDABAD 079 26425310
?AURANGABAD +919881249293
?BANGALORE 080 22230138
?BHUBANESHWAR 0674 2421901
?CALICUT 0495 2740334
?CHENNAI 044 42805544
?DELHI 011 32092369
?ERNAKULAM 0484 2341044
?GHAZIABAD 0120 6541564
?GOA 0832 2750992
?GUWAHATI +917896002188
?HUBLI 0836 2236919
?HYDERABAD 040 27550293
?INDORE 0731 4021148
?JAIPUR 0141 2392993
?KOLKATA 033 23452581
?LUCKNOW 0522 4043251
?LUDHIANA 0161 2532170
?MANGALORE 0824 2442176
?MUMBAI 022 65133299
?MYSORE 0821 2570171
?PATNA +919955542254
?PUNE 020 64781879
?RAIPUR 0771 4038300
?SALEM 0427 2211454
?SHIMOGA 08182 406022
?TRICHY 0431 6454649
?TRIVANDRUM 0471 2558648
?VIJAYAWADA 0866 3254587
?VISAKAPATNAM 0891 6469499