programmab le logic - panateq · usb, display port mtca-zu1 xilinx zynq ultrascale+ ... 2...
TRANSCRIPT
Block Diagram
Overview MTCA-ZU1 is a MicroTCA.4 compliant module based on the Xilinx Zynq UltraScale+
MPSoC.
The Zynq UltraScale+ integrates a Quad-core ARM Cortex-A53 (up to 1.5 GHz) based
Application Processing Unit (APU), a Dual-core ARM Cortex-R5 (up to 600MHz) ba-
sed Real-Time Processing Unit (RPU), a ARM Mali (up to 667 MHz) based Graphic
Processing Unit (GPU) and an UltraScale+ Programmable Logic (PL) in a single de-
vice.
It also includes on-chip memory, external memory interfaces, and a rich set of pe-
ripheral connectivity interfaces.
The first version of the board is equipped with a XCZU9EG-1FFVB1156 device tightly
coupled with 2/4GB of 64-bit + ECC of DDR4 Processing System (PS) memory run-
ning at up to 2400Mb/s. A private memory of 1/2GB 32-bit DDR4 is provided for the
Programming Logic (PL) application.
For I/O interfaces, two on-board FMC slots compliant to the Vita 57.1 HPC standard
with 80 LVDS and 8 SerDes, allowing a wide range of applications.
© PanaTeQ Nov 2016 Version 1.4
Key Features MicroTCA.4 compliant
Double Width Mid-Size
Xilinx Zynq UltraScale+ MPSoC
SoC 4-Core ARM53 + 2-Core ARM R5 + GPU Mali-400
On-board PCIe Gen2 Switch
PCIe 2x x4 Gen2 to the Backplane
4x GTH to the Backplane
2/4GB DDR4 72-bit PS Memory
1/2GB DDR4 32-bit PL Memory
2x 128MB NOR SPI, 512KB MRAM
4x USB, 1x SATA, 2x RS-232/422/485
ETH 2x 1000Base-T, 2x 1000Base-BX
2x CAN, 20 GPIO
2x FMC HPC Slots
80x LVDS 8x GTH per FMC
microSD card socket
MMC IPMI 1.5
microRTM : 2x 1000BaseT, 2x SATA, 2x USB, Display Port
MTCA-ZU1 Xilinx Zynq UltraScale+ MicroTCA.4 with two FMC slots
www.panateq.com
Typical Applications High Energy Physics
Video and Signal Real-Time Proces-sing
Multi-Axes Motor Controller
Software Defined Radio (SDR)
RADAR/LIDAR
High Speed Data Networking
JESD204B Quad ADC 16-bit Dual QSFP+
QSPINOR FLASH
DDR4-2400
DDR4-2400
GETH PHY
APUQuad-Core
ARM Cortex-A53Up to 1.5GHz
SRAM256KB
RGMII
GETHMAC1
SPI Master
PCIe
I2C
GETH PHY
RGMII
AMC Connector P1
1000BX
DATA[15:0]
DATA[31:16]
MMCATMega128
DC/DC
VCC_0V9
VCC_3V3
VCC_1V5
VCC_1V2
AMC_PWR (12V)
QSPINOR FLASH
eMMC SD CARDSocket
TERM
RTC
DDR4-2400
TERM
DATA[31:16]
FMC1 HPC Connector
Programmable LogicUltraScale+
MemoryControl
Xilinx Zynq UltraScale+ SoCXCZU6EGXCZU9EG
XCZU15EG
FFVB1156 35x35 mm
GETHMAC2
DDR4-2400
DDR4-2400
DATA[48:17]
DATA[63:49]
DDR4-2400 DATA[71:64]
DDR4-2400
RPUDual-Core
ARM Cortex-R5Up to 600MHz
GPU ARM Mali-400Up to 667MHz
DATA[15:0]
80x LVDS
8x GTH
PCIe x4 Gen2
4x CLK
1000BX
IPMI
2x UART
FMC2 HPC Connector
80x LVDS
8x GTH
4x CLK
2x USB 3.0ULP
RTMConnector
2x SATA 3.1
20x LVDS
8x LVDS
2x GETH
2x USB 3.1
2x UART
4x GTH
SMA Connector
Ref_In
Board Specifications MicroTCA.4 InterfacesMicroTCA.4 Interfaces
PICMG® MicroTCA.4 Specification compliant
Double width Mid-size
2 port PCIe x4 Gen2 connected to on-board PCIe Gen2 Switch
4x SerDes GTH @16.3 Gb/s directly connected to ZynQ Programming Logic
2 x1000BASE-BX links towards Switching Fabric
8x LVDS (Triggers)
Module Management Control (MMC) Interface implemeting IPMI 1.5 for temperature monitoring and hot-wap support
Xilinx Zynq UltraScale+ MPSoC (16nm Technology)Xilinx Zynq UltraScale+ MPSoC (16nm Technology)
Supported Devices : XVZU6EG-1FFVB1156 / XCZU9EG-1FFVB1156 / XCZU15EG-1FFVB1156
Processing System : Quad-Core ARM A53, Dual-Core ARM R5, GPU Mali-400, 2x SATA, 2x USB, 4x GETH MACs
Programmable Logic : 214K LUTs (ZU6EG) / 274K LUTs (ZU9EG) / 341K LUTs (ZU15EG)
On-Chip Memories : 25.1Mb (ZU6EG) / 32Mb (ZU9EG) / 57.7Mb (ZU15EG)
DSP Slices : 1973 (ZU6EG) / 2520 (ZU9EG) / 3528 (ZU15EG)
SerDes : 24 full duplex, high performance, GTH multi-gigabit SerDes tranceivers @ 16.3 Gb/s
2x 10-bit, 1MSPS ADCs for System Monitoring
Supported by PanaTeQ’s FPGA Development Kit (PAN-FDK)
External MemoriesExternal Memories
4/8GB SDRAM DDR4-2400 Processor System memory, 64-bits data, 8-bit ECC
1/2GB SDRAM DDR4-2400 Programmable Logic memory, 32-bits data
2x 128MB of QSPI NOR Flash memory for booting FPGA Zynq and Firmware
512KB of SPI MRAM (NVRAM)
SD-Card slot for up to 64GB NAND Flash memory
FMC SlotsFMC Slots
Fully compliant to VITA 57.1. High Pin Count (HPC) connector
8 high-performance GTH SerDes @16.3 Gb/s to/from FPGA Zynq
80 LVDS pairs to/from FPGA Zynq
2 clocks to FPGA Zynq Programmable Logic
2 clocks to FPGA Zynq GTH
uRTM InterfacesuRTM Interfaces
2x 1000Base-T
2x USB 3.0/2.0 , 2x USB 2.0 1x SATA 3.1
1x Display Port 1.2, 2x RS-232/RS-422, 2x CAN 2.0
20x GPIO, IPMI, JTAG
Pre-Ordering Information
MTCA-ZU1-A : XCZU6EG version
MTCA-ZU1-B : XCZU9EG version
MTCA-ZU1-C : XCZU15G version
PanaTeQ Engineering At Your Service
Contact Information
Xilinx Zynq UltraScale+ MPSoC Processing System Highlights
Applications processing unit (APU) with quad-core ARM® Cortex™-A53 processors: Next-generation ARMv8 architecture supporting 32- or 64-bit data widths
Ideal for Linux and bare-metal SMP/AMP application systems
Real-time processing unit (RPU) with dual-core ARM Cortex-R5 processors: Low-latency, highly deterministic performance APU offloading
New integrated hardened multimedia blocks: Graphics processing unit (GPU) [ARM Mali™-400MP2]
4Kx2K 60fps video encoder/decoder (VCU) [in select devices]
4Kx2K 30fps DisplayPort interface
New integrated high-speed peripherals: PCIe® Gen1 or Gen2 root complex and integrated Endpoint block in x1, x2, and x4 lanes
USB 3.0/2.0 with host, device, and OTG modes
Gigabit Ethernet with jumbo frames and precision time protocol
SATA 3.1 host
Dedicated quad transceivers up to 6Gb/s
General and boot peripherals: CAN, I2C, QSPI, SD, eMMC, and NAND flash interfaces
GPIO, UART, and trace ports
6-port DDR controller with ECC, supporting x32 and x64 DDR3, DDR3L, LPDDR3, LPDDR4, DDR4
Integrated platform management unit (PMU) supporting multiple power domains
Integrated configuration security unit (CSU)
TrustZone support
Peripheral and memory protection
PanaTeQ Engineering At Your Service