Professional Line Marker

1

The Professional Line Marker is the perfect machine for professionally marking out multiple sports grounds. Light weight for ease of use, requiring only the liquid mix to be added to the HUGE 34lt container. Battery powered and simply operated by the flick of a switch.Features: 12lt flush tank, 34lt liquid tank, Easy release locking lidSide or front mount for nozzle assembly, Marking discs, Handy tool boxInstant cut off at the nozzle, Puncture proof tyres.

Preparation for use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Line Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Marking Liquids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Transport and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Professional line marker

Contents

2

1. Remove the machine from its box, raise the handle bar. Swing the brace into position to secure the handlebar. Plug the lead from the bottom of the handle into the socket on the back of the machine.2. The machine is now ready for operation as the batteries are fully charged prior to dispatch.3. The spray system can be adjusted from the forward position to a side mounted position either side of the machine by simply sliding out the nozzle arm and sliding it into the side mount holder.4. The width of the line can be adjusted to your requirements by simply raising, lowering or twisting the spray nozzle.5. If a more intense line definition is required this can be achieved using a higher volume nozzle tip. For more information on Volume Control nozzle tips, please contact your local Supaturf Representative. Your machine is supplied with a nozzle to suit most applications.6. Remove the top tank from the machine and add water to the bottom tank (only add what you think is required) then replace the top tank. Turn the valve on rear of machine to the left and flick switch on handle bar, let machine run until an even spray appears through the nozzle tip. (This will remove air from the lines).

7. Add the appropriate amount of water (to give the desired dilution ratio) into the top tank, thoroughly stir the liquid concentrate and pour the desired amount on top of the water in the top tank and mix well using the stirrer supplied or disconnect the clear tube from the smv and connect it to push in fitting on top of the tank, flick the switch and liquid will self mix whilst you walk out onto the ground. It is essential that you place the lid on the containers to avoid spillage.8. Flick the switch off and return the tube to the smv. Flick the switch again - wait until the colour appears solid. The machine is now ready for marking lines.9. If at any time you wish to stop marking for an extended period of time, simply turn the valve to the left and flick switch to flush water through the pump and nozzle tip. To resume marking again, turn the valve to the right again, flick switch and wait for the colour to appear solid. (Please note that this is intended only for short periods – the full cleaning procedure must be followed if machine is to be inactive for longer periods).

Preparation for Use

3

1. Walk at a reasonable walking pace when line marking.2. Once the ground has been marked out, allow the line to dry – the longer, the whiter and brighter.3. For circle marking, use the circle marker attachment that is available (as an optional extra) for the perfect circle or simply lift the back or front wheels to mark the circle.4. Avoid airlocks by not running the pump dry.5. At the end of the line marking, it is essential to thoroughly clean out the machine. It is a good idea to use the remaining liquid over the previously marked lines rather than storing it. The liquid has a preservative in it, but once diluted the storage life is greatly reduced.6. Cleaning is a simple process of turning the valve to the left and running the machine to flush the pump and nozzle while removing the top tank and filter to give then a thorough clean. Replace these and add a little clean water into the top tank, turn valve to the right and give the machine another flush to remove what may be in the hoses. Disconnect the snap fitting before storing.

7. The line marking liquid is supplied in a recyclable container, simply rinse it out, remove the metal handle and place into your recycling bin.8. It is essential at this stage to connect the machine for battery recharging. This is done by simply plugging the charger in at the rear of the machine and into a standard 240-volt power outlet and leaving it there. (See Battery Charging).

Supaturf has a range of liquids available, our sales teams can help you select a product to give you what you require in the most cost effective manner .

Line Marking

4

Supaturf has developed this machine and its range of line marking concentrates as a complete package.These products are technologically advanced liquid concentrates developed to give optimum performance. The liquid mixes instantly with water at flexible dilution ratios (up to 1:8) to suit ground conditions and line requirements. It is recommended that an initial marking should be carried out at a dilution ration of 1:4.Supaturf liquid concentrates produce long lasting, durable and rain resistant bright lines, for normal marking conditions, others are designed for easy removal a short time after application where a change of code or sport is a requirement. Again talk to our sales people to achieve the best results.A standard Rugby ground should take approximately 16-18 litres, AFL Ground 12-16 litres and Soccer Ground 10-12 litres of liquid mix to mark out.Standard Colours Available:White, Black, Red, Red Sienna, Blue, Yellow and Green .Custom colours are available on request .

Marking Liquids

5

Due to the quality of the Supaturf product range, cleaning the machine is now faster and easier. The lack of resins and oxides present in the marking compounds ensures a quicker more thorough clean each time.On no account should liquid be left in the system after use .Short periods of inactivity are fine (if unsure of time stopped use the quick flush system) but make sure the machine is thoroughly cleaned after marking is finished.Clean the machine as stated in (line marking), leave water in the lines as this will avoid air locks, but disconnect the snap fitting.Clean the nozzle by scrubbing with the toothbrush provided andcontinuing to flush with clean water. DO NOT use wire or a pin to cleanthe hole of the nozzle tip as it will cause damage and a subsequentincrease in liquid output. Unscrew the filter bowl, remove filter screen andrinse/clean both thoroughly. You may use the toothbrush to assist withcleaning, be careful not to lose the filter seal (rubber ring).The machine is now ready to be charged.

A charger has been included with your machine and should be used as often as possible during regular use. This will help the batteries last longer.1. Plug the charger into a power point.2. Attach the plug from charger into socket at rear of machine. A red light indicates charging and a green light indicates that the battery is fully charged.3. Recharge will automatically cut out when batteries are fully charged and cut back in when batteries lose voltage. When machine is not in use, the charger can be left on at all times. The lights on the back of the machine indicate the amount of charge in the batteries.Batteries are fully charged when:1. All red and green lights are lit up when switch is activated.2. The light to the left is on and green when connected to the charger and batteries are charged. Re-Charging is required when both green lights are no longer showing and the orange light is becoming dull.

Cleaning Battery Charging

6

Little maintenance is required due to the high quality of the liquids and user friendly nature of the machine. Regular maintenance will ensure reliability and should include;1. Always clean nozzle tip with toothbrush provided. It is advisable to have a few spare nozzle tips in case of damage. These are available from your local Supaturf Distributor. Remove the nozzle tip and rubber seal from spray management valve and store in clean water between markings.2. Attach battery charger after each marking – See Battery Charging.3. Wash down machine and dry with a cloth.

1. Make sure the snap fitting is disconnected.2. Disconnect battery charger and remove power lead from rear of machine.3. Fold the handle forward.4. Your line marker weighs 28kg when empty.Observe OH&S procedures when lifting machine .

Your Professional Line Marking machine comes with a 12-monthwarranty. Please fill in your warranty card and return to Supaturf.

Maintenance Transport & Storage

Warranty

7

Professional Line Marker - Parts Part No Description Code 1 Starlock Washer S/W 2 Wheel WHEEL 3 Rear Axle P/RA 4 Chassis P/CH 5 Side Mount Arm SM/A 6 Hand Knob - 6mm H/K 7 Ezy Loop x2 E/L 8 Side Mount Bracket SM/B 9 Front Axle P/FA 10 Nozzle Arm N/A 11 Spray Management Valve SMV

1

1

2 2

22

34

5

6

6

78

9

1

1

10 11

6

8

Professional Line Marker - Parts Part No Description Code 12 Hand Knob - 12mm H/K/12 13 Washer M12x3 15 Handle Bar H/B 16 Tank - Pro P/T 17 Spacer & Screw SP24/M6x50 18 Handle Bar Grip HBG 19 Rocker Switch R/SW 20 Tool Box T/BOX 22 Handle Bar Brace H/B/B 23 Screw M6x40

1212 13 13

1516

17 17

181819

20

2223

9

Professional Line Marker - Parts Part No Description Code 24 Battery X 2 B/12 25 Pump PUMP 25A Pump & Fittngs PUMP/PRO 25B Tube Fittings TF8/38 26 Control Box C/BOX 27 Cable CABLE/P 28 Rocker Switch R/SW 29 Fuse - 5amp FUSE 30 Wiring Loom W/LOOM/P

24

25A

25

26

27

28

2930

25B

25B

10

Professional Line Marker - Pump Tray Part No Description Code 31 Pump Tray P/TR

31

11

Professional Line Marker - Spray Management Valve Part No Description Code 34 Spray Management Valve Complete SMV 35 Tube Fitting TF/8 36 Nozzle N/SMV 37 Quick Valve QV 38 Diagram Rubber DR 39 Rubber Washer QV/R 40 Nozzle Tip N/TIP 41 Nozzle Cap N/C

34

35 36 37

38

39 4041

12

Professional Line Marker - Valve Train Part No Description Code 42 Tube Fitting - Elbow TF8/EL 43 Clear Tube C/T 44 3 Way Valve B/V 45 Tube Fitting TF/8 46 Nipple - 1/4 1/4NIP 47 Reducing Bush R/B 48 Filter FILTER 48A Filter Seal F/S 48B Filter Screen F/SC 48C Filter Bowl NA 49 Male/Female Elbow - 1/4 ME/EL/1/4 50 Snap Fitting SNAP/PRO

42

42

4243

4344

45

4647

47

48A 48B 48C

49

50

5048

13

Professional Line Marker - Accessories Part No Description Code 1 Battery Charger CHAR 2 Spare Parts Bag SPB 3 Nozzle Brush N/B 4 Liquid Stirrer STIRRER 5 Liquid Strainer STRAINER

*Spare Parts Bag includes 1x Tank Drainer 1x Filter Seal 1x Diagram Rubber 2x Rubber Washer 2x Nozzle Tips 1x Fuse

1

2

3

4

5