product guide - home | vj technology online
TRANSCRIPT
Scaffolding
Product Guide
vjtechnology.com
#confidentinquality
Anchor selection Not all anchors are suitable for use in all base
materials. What follows is a suggested short list for
fixing systems suitable for specific base materials and
substrates. The final selection will depend on the load
requirement and preliminary, or suitability, tests:
If you require advice on anchor selection, please call
our Technical Department 01233 652520
Concrete: n Drop In anchor (Concrete only. Not for other
masonry substrates)
n Self-tapping concrete screws (screwbolts)
n Resin anchors
n Nylon anchors with screw eyes
Brickwork & Stonework: n Self-tapping concrete screws (screwbolts)
n Resin anchors
n Nylon anchors with screw eyes
Concrete Blockwork: n Check block strength, structure and presence of voids
n Self-tapping concrete screws (screwbolts)
n Resin anchors (with mesh sieves in slotted blocks)
n Nylon anchors with screw eyes
Lightweight Blockwork: n Check block strength, structure and presence of voids
n Resin anchors (with mesh sieves in slotted blocks)
n Nylon anchors with screw eyes
Timber: n Coach screws
n Screw eyes
Steel: n Self-drill self-tap screws (Construction screws)
n Bolts for hollow sections (Blind Bolt,
Lindapter Hollo Bolt and Mola Bolt)
Anchor installation All anchors should be installed strictly
in accordance with the manufacturer’s
recommendations.
n Correct hole diameter
n Holes should be free of dust and
debris – brush and pump (most important
for resin anchors)
n Correct setting tools must be used
(especially for Drop in anchors)
n Tighten to the recommended torque
according to manufacturers data
Anchor positioning All anchors should be installed with the
manufacturer’s recommendations for edge
and axial spacing. Anchor positioning in
brickwork needs additional consideration:
NASC TG4:11 Section 5.3 has guidance for
the positioning of fixings in brick walls which
should be observed.
Scaffolding product guideVJ Technology (VJT) is a market-leading distributor and manufacturer of fasteners, tools, technical fixings systems and
associated products to the UK’s construction and civil engineering industries. Our long-term customers include a wide
range of the most renowned names in the country, among them main contractors and specialist subcontractors.
We have particular expertise in supplying high quality products and technical systems to the Scaffolding sector
such as heavy anchors, chemical injection resins, tool tethering systems and PPE.
Our product range is constantly evolving as new products and technologies enter the market, sourced from
a mix of leading and global companies and specialist suppliers. As required by the CPR, we offer CE Marked
products either ETA or HEN.
This product guide should be read in conjunction with the Guidance Notes: NASC TG4:11 “Anchorage Systems
for Scaffolding” and NASC TG20:13 “Guide to Good Practice for Scaffolding with Tube and Fittings”.
2 Ashford Sales 08000 828 828 Glasgow Sales 08000 828 830
Technical Support Product and Application AdviceWith a dedicated in-house Technical Department,
we can offer comprehensive and impartial technical
advice including:
n Bespoke Technical Calculations
n H&S and Technical Datasheets
n Method Statements (RAMS)
Product TestingVJT has an in-house, test laboratory which carries
out bespoke suitability and proof-testing for specific
projects and products, and is UKAS accredited for site
tensile load testing of heavy-duty
anchors or fixings.
Toolbox TalksAs a leading distributor of fixings and tools to the UK’s
construction industry, VJT takes the health and safety
of its customers extremely seriously.
Toolbox talks are a simple and effective way to
communicate workplace hazards to be aware of,
explain and train on safe installation methods and,
ultimately, reduce workplace incidents.
The Building Structure The suitability of the building structure to
sustain the loads transferred from the scaffold
must always be checked by the designer.
On-Site Testing
See NASC TG4:11 Section 6Site tests can be required for two specific purposes:
n Preliminary tests: These tests are used to check
the suitability of a particular fixing in the base
material to help determine allowable loads.
n Proof tests: These tests are required to check the
quality of installation and should be carried out
on all projects.
n Site tests should be carried out by trained
competent personnel using a suitable calibrated
test meter.
All VJT Technical Sales Managers are members of
the CFA Approved Testers Scheme.
Quality and Accreditation: ISO 9001: 2015
UKAS Accredited Test Laboratory
3Technical Advice: 01233 652520 [email protected] vjtechnology.com
VJTStock Code
ProductDescription
Size Effective Depth
09330330 VJT 4Tech SDS Plus 10.0 x 160 10 x 160mm 100mm
09330140 VJT 4Tech SDS Plus 12.0 x 160 12 x 160mm 100mm
09330470 VJT 4Tech SDS Plus 14.0 x 160 14 x 160mm 100mm
09330540 VJT 4Tech SDS Plus 16.0 x 200 16 x 200mm 140mm
Full Range Available
4Tech SDS Plus Drill Bit
4
Scaffolding Product Catalogue
VJTStock Code
ProductDescription
Size Effective depth
09320380 VJT Endurance 10 x 160 10 x 160mm 100mm
09320490 VJT Endurance 12 x 160 12 x 160mm 100mm
09320630 VJT Endurance 14 x 210 14 x 210mm 150mm
09320770 VJT Endurance 16 x 210 16 x 210mm 150mm
09320850 VJT Endurance 18 x 210 18 x210mm 150mm
09320930 VJT Endurance 20 x 210 20 x 210mm 150mm
Full Range Available
SDS Plus Drill Bit Standard
Screw Eyes
Coach Screws
Scaffolding Product Guide
Drill Bits
Scaffold Screw Eyes
Hex Sets
VJT Stock Code
Product Description
Size MinimumDrill Hole Depth
Drill Hole Diameter
Internal Eye Diameter
02500010 12 X 90 Screw Eye 12 x 90 23mm
02500020 12 x 120 Screw Eye 12 x 120 23mm
02500030 12 x 160 Screw Eye 12 x 160 23mm
02500050 12 x 230 Screw Eye 12 x 230 23mm
02500060 12 x 300 Screw Eye 12 x 300 23mm
02500070 12 x 350 Screw Eye 12 x 350 23mm
02500080 14 x 70 Nylon Plug for Screw Eye 14 x 70 80mm 14mm
VJT Stock Code
Product Description
Size Spanner/ Drive AF
16200620 12 X 80 BZP Coach Screw 12 x 80mm 19mm
VJT Stock Code
Product Description
Spanner/ Drive AF
14800640 M12 X 40 BZP Hex Set Grade 8.8 12 X 40mm 19mm
14800650 M12 X 45 BZP Hex Set Grade 8.8 12 X 45mm 19mm
14800780 M16 X 40 BZP Hex Set Grade 8.8 16 X 40mm 24mm
14800790 M16 X 45 BZP Hex Set Grade 8.8 16 X 45mm 24mm
Hexsets other sizes, diameters and finishes available
Key Points
n 4 Cutting Edge Blade
n Minimised Drag
n Deep Drilling
n Reduced Blow Out
Coach Screws other sizes and diameters available
Size
Ashford Sales 08000 828 828 Glasgow Sales 08000 828 830
Scaffolding Product Catalogue
Drop In Anchor
Eyebolt and Shackles
Blind Bolts and Connectors
Stud Screwbolt and Connectors
Scaffolding Product Guide
Fixings
VJT Stock Code
Product Description
Size Embedment Drill Hole Diameter
Internal ThreadLength
02100070 M16 Drop In Anchor for Concrete M16 65mm 20mm 22mm
02100040 M12 Drop In Anchor for Concrete M12 50mm 15mm 19mm
02300050 M16 Setting Tool M16
02300040 M12 Setting Tool M12
02600010 Standard M16 Scaffold Ring Bolt M16
VJT Stock Code
Product Description
Size Drill Hole Diameter
Fixing thickness
24300040 M12 Blind Bolt: Fixing to hollow section steel M12 13mm 12 to 35mm
24300050 M16 Blind Bolt : Fixing to hollow section steel M16 17mm 13 to 45mm
17500080 Stud Connector for M12-16 M12-M16
17500050 Stud Connector for M16 M16
02600010 Standard Scaffold Ring Bolt M16
24300060 M16 x 60 BZP Molabolt M16 16mm 7 to 32mm
Lindaptor Hollo-Bolt :Fixing to hollow section steel
Lindaptor Hollo-Bolt : (Please see our website for more details)
VJT Stock Code
Product Description
Size ThreadLength
Eye
23400330 Eyenuts Din 582 M12 Self-colour SWL in tension 3.4kN M12 11mm 30mm
23400340 Eyenuts Din 582 M16 Self-colour SWL in Tension 7.0kN M16 13mm 35mm
23400250 Eyebolts Din 580 M12 Self-colour SWL in Tension 3.4kN M12 22mm 30mm
23400260 Eyebolts Din 580 M16 Self-colour SWL in Tension 7.0kN M16 28mm 35mm
VJT Stock Code
Product Description
Size MinimumDrill Hole Depth
Drill Hole Diameter
Spanner/ Drive AF
02800260 Toge Screw Stud BZP 10x120 M12x25 10 X 120 95mm 10mm 9mm
02800290 Toge Screwbolt Stud BZP 14 x 165 M16 x 35 - 202-141-650 14 x 165 135mm 14mm 12mm
17500080 Studding Connectors for TSM B10 X 120/M12 M12-M16
17500050 Studding Connectors for TSM B14 X 165/M16 M16
02600010 Standard M16 Scaffold Ring Bolt M16
5Technical Advice: 01233 652520 [email protected] vjtechnology.com
Concrete Temperature: Celsius
Gel/Working Time (Minutes)
Cure Time
-10 120 24 Hours
-5 90 14 Hours
0 45 7 Hours
5 25 2Hours
10 15 80 Min
20 6 45 Min
30 2 25 Min
40 1.2 15 Min
Scaffolding Product Guide
EC410+
E410+
V420+
Resins & Accessories
n V420+ Hybrid is a high performance vinylester resin that is styrene free.
n ETA for cracked and non-cracked concrete
n ETA for post installed rebar connections
n C2 Seismic rated
n Fire rated ~ F120
n NSF approval for potable water
n Suitable for dry & wet concrete [not flooded holes]
n High load capacity
n Suitable for most base materials
Concrete Temperature: Celsius
Gel/Working Time (Minutes)
Cure Time
-5 90 6 Hours
0 45 3 Hours
5 25 2 Hours
10 20 100 Minutes
20 6 45 Minutes
30 4 25 Minutes
40 2 20 Minutes
n E410+ is a general purpose styrene free epoxy acrylate resin.
n ETA for anchor studs in non-cracked concrete
n ETA for anchor studs in masonry
n Suitable for anchor studs and rebar
n Dry and wet concrete [not flooded holes]
n High load capacity
n Suitable for most base materials
Concrete Temperature: Celsius
Gel/Working Time (Minutes)
Cure Time
-10 60 4 Hours
-5 45 2 Hours
0 25 80 Minutes
5 10 45 Minutes
10 4 25 Minutes
15 3 20 Minutes
20 2 15 Minutes
n EC410+ is a general purpose express cure styrene free epoxy acrylate resin.
n Express cure winter formulation
n ETA for anchor studs in non-cracked concrete
n ETA for anchor studs in masonry
n Suitable for anchor studs and rebar
n Dry and wet concrete [not flooded holes]
n High load capacity
n Suitable for most base materials
6
VJT Stock Code
Product Description
Size Use for
06000075 V420+ Hybrid High Perform ETA Vinyl Sty Free Fire Rated Resin 420ml Concrete
06000010 E410+ Epoxy Acrylate Sty Free Resin & Nozzle 410ml Masonry and Non-Cracked Concrete
06000020 EC410+ Express Epoxy Acrylate Sty Free Resin & Nozzle 410ml Masonry and Non-Cracked Concrete
06100240 Steel Bottle Brush 14mm Dia x 400mm (M12 & H12)
06100250 Steel Bottle Brush 18mm Dia x 400mm (M16 & H16)
04900290 CAS5 M12 X 160 BZP Resin Anchor Stud
04900300 CAS5 M16 X 190 BZP Resin Anchor Stud
06100010 Resin Applicator Gun
06100100 Hand Air Pump
Resins
Ashford Sales 08000 828 828 Glasgow Sales 08000 828 830
Scaffolding Product Guide
Hole Plates
Hole Plates
Resins & Accessories (Continued)
[email protected] www.vjtechnology.com 7
Insert anchor to base of hole with a twisting action.
Clean hole by brushing & blowing, repeat sequence at least 4 times.
Starting from back, inject resin until hole is at least half full.
Drill correct size hole.1.
5. 6.
2.
Visually check to ensure sufficient resin has been used.
Screw mixer nozzle onto cartridge.
Allow full cure time before attaching fixture & applying torque.
Extrude to waste until resin is a consistent colour.
Resin use step-by-step guide
3. 4.
7. 8.
VJT Stock Code
Product Description
Size MinimumDrill Hole Depth
Drill Hole Diameter
Spanner/ Drive AF
02700010 One Hole Plate 19mm Hole
02700020 Two Hole Plate 19mm and 19mm x 27 Slot
02750270 Screwbolt FBS II 14x125 60/40/10 US Hex Integral Washer 14 x 125mm 140mm 21mm
04000120 Rawl M12/25L BZP Shield Anchor 12mm 85mm 20mm 19mm
02700270 Plate Connector M16 for timber and masonry: 12.5mm Holes
02700280 Plate Connector M16 for steel: 6mm Holes for Teks Screws
16200620 12 x 80 Coach Screw (Full Range Available)
02750120 Screwbolt FBS II 10x100 45/35/15 US Hex Integral Washer 10x100mm 110mm 10mm 15mm
VJT Stock Code
Product Description
Size Steel thickness
Fixing thickness
13650090 Ejot HS 5.5 X 38: Fixing to 4.0mm - 10.0mm steel 5.5 x 38mm 4 to 10mm 4.0 x 16.0mm
13601250 TSHW 5.5 X 50: Fixing to 3.5mm - 18.0mm steel Supertek 7 5.5 x 50mm 3.5 to 18mm
13600180 DrillTech CS HS 5.5 x 38 Hex Tek 5 -12mm 5.5 x 38mm 5 to 12mm
Technical Advice: 01233 652520 [email protected] vjtechnology.com
Scaffolding Products
Scaffolding Product Guide
VJTStock Code
ProductDescription
Size
17100050 M12 X 3000 Grade 4.6 BZP Studding M12
17100060 M16 X 3000 Grade 4.6 BZP Studding M16
Other size. Diameters and finishes available
17500040 Stud Connector for M12 M12
17500050 Stud Connector for M16 M16
17500080 Stud Connector for M12-M16 M12-M16
BZP Studding and Connectors
VJT Stock Code
Product Description
Size MinimumDrill Hole Depth
Drill Hole Diameter
Spanner/ Drive AF
02750110 FBS II 10x90 35/25/5 US Hex Integral Washer 10 x 90mm 100mm 10mm 15mm
02750120 FBS II 10x100 45/35/15 US Hex Integral Washer 10 x 100mm 110mm 10mm 15mm
02750130 FBS II 10x120 65/55/35 US Hex Integral Washer 10 x 120mm 130mm 10mm 15mm
02750140 FBS II 10x140 85/75/55 US Hex Integral Washer 10 x 140mm 150mm 10mm 15mm
02750210 FBS II 12x110 50/35/10 US Hex Integral Washer 12 x 110mm 120mm 12mm 17mm
02750220 FBS II 12x130 70/55/30 US Hex Integral Washer 12 x 130mm 140mm 12mm 17mm
02750230 FBS II 12x150 90/75/50 US Hex Integral Washer 12 x 150mm 160mm 12mm 17mm
02750270 FBS II 14x125 60/40/10 US Hex Integral Washer 14 x 125mm 140mm 14mm 21mm
02750370 FBS II Checking gauge FUP 10
02750380 FBS II Checking gauge FUP 12
02750390 FBS II Checking gauge FUP 14
29150780 Gedore Impact Socket 15mm 1/2Sd
29150800 Gedore Impact Socket 17mm 1/2Sd
29150820 Gedore Impact Socket 21mm 1/2Sd
VJT Stock Code
Product Description
Size Embedment Drill Hole Diameter
Spanner/ Drive AF
02870170 Thunderbolt APT 10 X 100 Concrete Screw 10 x 100 50 to 75mm 10mm 17mm
02870180 Thunderbolt APT 10 X 130 Concrete Screw 10 x 130 50 to 75mm 10mm 17mm
02870190 Thunderbolt APT 10 X 150 Concrete Screw 10 x 150 50 to 75mm 10mm 17mm
02870210 Thunderbolt APT 12 X 100 Concrete Screw 12 x 100 60 to 90mm 12mm 19mm
02870220 Thunderbolt APT 12 X 130 Concrete Screw 12 x 130 60 to 90mm 12mm 19mm
02870230 Thunderbolt APT 12 X 150 Concrete Screw 12 x 150 60 to 90mm 12mm 19mm
Concrete Screws and Sockets
Thunderbolts
Screwbolts
Accessories
8
Reusable in temporary works when using checking gauge
Cutting service available on request
Ashford Sales 08000 828 828 Glasgow Sales 08000 828 830
Scaffolding Products
Scaffolding Product Guide
VJT Stock Code
Product Description
Size
02700190 External Hook Scaffold Tie Coupler Fitting (EN74) 16mm dia hook
02700195 Internal Hook Scaffold Tie Coupler Fitting (EN74) 16mm dia hook
02700200 Bracket for Hook: Fix to steel and cladding M12
VJT Stock Code
Product Description
Size
02700110 Scaffold Tube Cap Yellow
02700120 Scaffold Bolt Cap Yellow
02500130 Scaffold Plug Cover for 14mm Nylon Plug (white)
02500140 Scaffold Plug Cover for 14mm Nylon Plug (grey)
02700030 Scaffold Tag with 2 Inserts
02700035 Scaffold Tag Inserts
02700040 Pen
24400030 Cable Tie Black 4.8 x 200mm
24400040 Cable Tie Black 4.8 x 300mm
24400050 Cable Tie Black 7.6 x 450mm
02700060 Ladder Tags
02700070 Ladder Tags Inserts
02700140 Poly Rope 6mm x 220m
02700145 Poly Rope 10mm x 220m
02700130 Tarpaulin 2.7 x 3.6m
02700135 Tarpaulin 5.4 x 7m
02700160 Ratchet Strap 25mm x 5m (1 Tonne)
02700150 Scaffold Spanner 7/16"
23600040 Banding 19mm steel (2 reel pack) BS EN 13246:2001
23600050 Banding Seals 19 x 25mm
23600060 Banding Sealing Tool 19mm
23600070 Tensioner
23600080 19mm Poly (19mm x 600m woven poly)
23600090 Poly Buckles
23600100 Poly Tensioner
02700090 Heavy Duty Hoarding Clip
02700100 Light Duty Hoarding Clip
26701530 Faithful SL250 10" 250mm Scaff Mag Level
Product Description
02700220 M16 Self Colour Round Washer 60mm diameter x 10mm thick
15600090 M16 Self Colour Square Plate 100 x 100 x 10
[email protected] www.vjtechnology.com
Scaffold Hooks
Scaffold Consumables
Washers
Accessories (Continued)
9Technical Advice: 01233 652520 [email protected] vjtechnology.com
Scaffolding Product Catalogue
Scaffolding Product Guide
+44 (0)1233 637695 (Scotland) +44 (0)141 2815000
VJT Stock Code
Product Description
Size Bore
10300110 Recip Blade S922BF For cutting tube 150mm
10300240 Recip Blade S3456XF For cutting board 200mm
10300320 Recip Blade S1617K For cutting board 300mm
10300190 Recip Blade S922HF Universal 150mm
25600028 Evolution Cold Cut Blade 14" /355m 14"/355mm 25.4
21000060 305 x 3.2 x 20 Steel Cutting Abrasive Wheel Petrol Cutter 305mm (12") 20
21000080 356 x 2.8 x 25 Steel Cutting Abrasive Wheel Chop Saw 356mm (14") 25.4
10900190 30mm Galvanised Clout Nail for edge trim repairs 25KG 30mm
VJTStock Code
ProductDescription
25000110 Extension Lead 1.5mm 16A 14M Loose Roll
25000130 Extension Lead 110v 25M Cable Reel
25000150 Extension Lead 110v 50M Cable Reel
Blades and Abrasives
Personal Protection Equipment
Blades & Abrasives
PPE
Electrical Equipment
Other electrical items available
Other items available
10
Other blades and sizes available on request
VJT Stock Code
Product Description
Size
24870065 Gloves - VJT Matrix Size 8
24870070 Gloves - VJT Matrix Size 9
24870080 Gloves - VJT Matrix Size 10
24880010 Gloves - VJT Orange Grip Size 9
24880020 Gloves - VJT Orange Grip Size 10
24880050 PPE VJT Cut Level 5 Gloves Size 9
24880060 PPE VJT Cut Level 5 Gloves Size 10
24800630 PPE Gloves 4543 Cut Level 5 Resistant Size 9 (TP5)
24800640 PPE Gloves 4543 Cut Level 5 Resistant Size 10 (TP5)
24800645 PPE Gloves 4543 Cut Level 5 Resistant Size 11 (TP5)
24800150 Dust Mask P1 FFP1 3M (Pack 10)
24800570 Dust-mask FFP2 (Box 10)
24800162 PPE Dust Mask FFP3 (Box 5)
24800100 PPE Safety Glasses
24800830 Sun Safety Glasses - Tinted
26050010 Bolle RUSHPPSI Safety Glasses VJT
26050240 Bolle BL10CI Clear Safety Glasses c/w Neck Cord
26050130 Bolle ATOAPSI Atom Safety Goggles
24800090 PPE Goggles
24800110 Ear Defenders Over Ear
24800120 Ear Defenders Ear Plugs (Pack 200)
24800130 First Aid Kit (20 Person)
24800160 PPE Hi-Vis Waistcoat Yellow
Ashford Sales 08000 828 828 Glasgow Sales 08000 828 830
Scaffolding Product Catalogue
Scaffolding Product Guide
VJT Stock Code
Product Description
Size Max Load
24790010 NLG Tether Loop 120mm 3kg
24790020 NLG Tether Loop 150mm 3kg
24790030 NLG Tether Loop 170mm 3kg
24790250 NLG Tether Ring 19mm 1kg
24790260 NLG Tether Ring 25mm 1kg
24790270 NLG Tether Ring 38mm 1kg
24790100 NLG D Ring Tether Small 1kg
24790110 NLG D Ring Tether Large 3kg
24790050 NLG Tool Tether Choke 18kg
24790060 NLG Tool Tether Choke Single Arm 18kg
24790070 NLG Tool Tether Choke Twin Arm 18kg
24790280 NLG Drill Boot Tether Small 2.7kg
24790290 NLG Drill Boot Tether Large 2.7kg
24790220 NLG Adjustable Wristband 3kg
24790230 NLG Adjustable Work-belt 30kg
24790180 NLG Retractable Lanyard Lightweight 0.5kg
24790190 Retractable Lanyard Locking Mechanism 1kg
24790090 NLG Tether Tape Roll 1 roll – 2.8m 5kg
24790130 NLG Helmet Lanyard
24790330 NLG Mini Coiled Lanyard 1kg
24790240 NLG Belt Loop for all Standards Belts 3kg
24790170 NLG Standard Bungee Lanyard 5kg
Deciding to add tool tethering to your workspace is vital for keeping both your workers and public as safe as possible.
Once you’ve made your choice, your next task is to ensure that your tool lanyards are fit for purpose and suitable for the
environment you are working in.
Third Party TestedEvery element of the NLG tool tethering system is tested and certified by an accredited UKAS test laboratory. All NLG tool lanyards
are tested with a 2:1 safety factor. That means all the lanyards, anchor points and tethers are all tested with double the weight of the
load rating.
Drop TestingNLG products also undergo dynamic drop testing to ensure they can cope in the real world. A dynamic drop test involves lifting the
tool to the full extent of the tool lanyard above the anchor point. This is where it’s dropped from. That tests the tool tether to its full
extension and makes sure that it can deal with the force of a dropped object coming to a sudden stop.
CE MarkingYour tool lanyards shows that they comply with the relevant EU safety, health and environmental requirements.
Serial NumbersYour tool lanyards offer traceability. We’re not just talking about traceability in the event that there’s a product fault and lanyards
need to be recalled. We’re talking about internal traceability too. Serial numbered tool lanyards allow you to assign tool tethering
equipment to particular employees. They can then be responsible for its condition and accountable for its maintenance.
Never Let Go
Tool Tethering
Tool Tethering - All you need to know
Technical Advice: 01233 652520 [email protected] vjtechnology.com 11
The benefits of tethering from your wrist include:
n Low snagging risk because of reduced length of the tool lanyard
n Very compact solution, making it ideals for confined work areas
n Lightweight componentry means that it remains comfortable, even with prolonged use.
NLG does not recommend attaching any tool over 1.5kg to the wrist, as the force generated from heavier tools could cause strain to the user if dropped.
The benefits of tethering from a tool belt include:
n Versatile, heavy-duty system suitable for most tools
n Multiple tools can be tethered and holstered, available for immediate use
n Large range of tool lanyards allows for different configuration options
Only tether tools up to 2.5kg of the waist/tool belt. Heavier tools and objects should be attached to a secure, load-rated anchor point.
#confidentinquality
✓
CONSTRUCTION FIXINGS & TOOLS
Environment and Waste We are committed to developing and promoting high
environmental standards in all areas of our business,
with a focus on reducing waste, increasing efficiency
and continuously improving our working practices.
Health and Safety We are committed to the health and safety of all
our employees, customers and suppliers.
Our technical sales team is qualified to instruct in the
correct use of abrasives and powder actuated tools,
as well as deliver tool box talks on anchor installation.
Quality Assurance We are committed to providing a quality of service
that consistently meets, or exceeds, our customer’s
needs. To help achieve this objective we have a
Quality Management System certified to ISO 9001:
2015, and regular reviews are carried out in our
quest for continual improvement.
Insurance VJ Technology can provide insurance downloads on
our website.
Locations Ashford
Technology House, Brunswick Road Ashford,
Kent, TN23 1EN
Glasgow
Unit 9, Maclellan Street, Kinning Parkway,
Glasgow, G41 1RR
Telephone Switchboard: 01233 637695
Ashford Sales: 08000 828 828
Glasgow Sales: 08000 828 830
Technical: 01233 652520
Email [email protected]
Website vjtechnology.com
Social Media