product datasheet flare series - farnell … datasheet flare series last update 26/6/2013 general...

PRODUCT DATASHEETFlare serieslast update 26/6/2013

Ordering number

FamilyTypeLEDColorDiameterHeightStyleOptic MaterialHolder MaterialFasteningStatus

CA10563_FLARE-C

FlareAssemblyXR-EClear24.5 x 24.5 mm14.55 mmRectangular PMMA - Screw, tape Ready

FWHMEfficiencycd/lmGerber File

8+90 degrees 93 % - Available

Ordering number


C10402_FLARE-C

FlareLensXR-EClear24.5 x 24.5 mm14.55 mmRectangular PMMA - Screw, glue Ready


84+7 degrees (simulated) 0 % 3.200 Available

Ordering number


C10527_FLARE-C-D

FlareLensXR-EClear24.5 x 24.5 mm14.55 mmRectangular PMMA - Screw, glue Ready


95+21 degrees (simulated) 0 % 1.000 Available

NOTE: The typical divergence will be changed by different color, chip size and chip positiontolerance. The typical total divergence is the full angle measured where the luminous intensityis half of the peak value.

October 31st 2013 5:43 Copyright Ledil Oy - Subject to change without prior notice - /2

Ledil Oy Salorankatu 10 24240 SALOFinland

http://www.ledil.com email: [email protected] FAX: +358-2-733 8001

PRODUCT DATASHEETFlare serieslast update 26/6/2013

GENERAL INFORMATION

- Product series especially designed & optimized for XR-E series of LEDs. - Special care taken to make light distribution as uniform as possible.- Lens material optical grade PMMA with high UV and temperature resistance (105 degrees of Celcius / 220degrees of Fahrenheit). Allows use of high current and temperature conditions.

Please find more information about used material from below:http://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20UL94_Yellow%20Card.pdfhttp://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20PLEXIGLAS-Datasheet.pdf

- Fastening to heat sink with a PU foam adhesive tape of automotive grade. Please find fastening details byclicking link: http://www.ledil.com/datasheets/DataSheet_TAPE.pdf

- Fastening to PCB with appropriate adhesive. By clicking link below you can find Ledil recommended glueoptions.http://www.ledil.com/datasheets/DataSheet_GLUES.pdf

NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the endproduct. For example, mechanical stress, vibration and holes on the surface of the circuit boarweaken the strength of the tape.

NOTE 2: Assembly to the surface must be made straight, so the tape bonds constant andbalanced with fastening surface. Slanted assembly might cause unbalanced bond to thesurface. All surfaces where tape is applied must be clean, dry and free from grease and dirt.

If cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of yourLED manufacturer - this is important as cleaning shall under no circumstances damage LEDs orother electronics components on the PCB.

Further note that optical components shall not be cleaned with any chemicals - only micro fibercloth may be used to remove fingerprints or other traces from handling.NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the endproduct. For example, mechanical stress, vibration and holes on the surface of the circuit boarweaken the strength of the glue.

NOTE 2: All surfaces where glue is applied must be clean, dry and free from grease and dirt. Ifcleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LEDmanufacturer -this is important as cleaning shall under no circumstances damage LEDs or otherelectronics components on the PCB.

Further note that optical components shall not be cleaned with any chemicals - only micro fibercloth may be used to remove fingerprints or other traces from handling.

October 31st 2013 5:43 Copyright Ledil Oy - Subject to change without prior notice - /2

Ledil Oy Salorankatu 10 24240 SALOFinland

http://www.ledil.com email: [email protected] FAX: +358-2-733 8001

AD

BC AD

32

41 1

DESIGNED BYHH

DATE15.08.2007

CHECKED BYJJ

DATE23.06.2008

DRAWN BYPV

DATE23.06.2008

This drawing is our property.It can't be reproducedor communicated withoutour written agreement.

SCALE 2:1 WEIGHT(g) SHEET 1/1

SIZE

A4DRAWING NUMBER REV

1.0

DRAWING TITLE

Ledil Oy

Tehdaskatu 13

FIN-24100 SALO

Finland

Datasheet FLARE-C-DIFF

11527

Diffuser finish

14.55

0.95

Side viewScale: 2:1

11.5

10

2 4.45

3.936.83

2.55

2.2

Bottom viewScale: 2:1

Auxiliary view AScale: 2:1

PCB top

Led