product catalog - opico · 2008-01-14 · corporation 1 product catalog insulated concrete forms ....

Corporation 1

PRODUCT CATALOG

Insulated Concrete Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Panel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

T Form Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Ceiling and Flooring Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Alignment Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

TECHNICAL BULLETINS

Brick Ledge Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11

Floor Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13

Ceiling Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15

Waterproofing Membrane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17

T Form Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19

Tall Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21

Multi Purpose Anchor/Hanger System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Retrofit Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Roof/Hurricane Anchor System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Monotruss Hanger System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Low Expansion Foam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

TABLE OF CONTENTS

2 Corporation

INSULATED CONCRETE FORMS

Standard Length 96" (2438mm) 96" (2438mm) 96" (2438mm) 96" (2438mm) 96" (2438mm)

Form Unit Width 9 1/4" (235mm) 11 1/4" (286mm) 13 1/4" (337mm) 15 1/4" (387mm) 17 1/4”(438mm)

Height 18" (457mm) 18" (457mm) 18" (457mm) 18" (457mm) 18" (457mm)

EPS Thickness 2 5/8" (67mm) 2 5/8" (67mm) 2 5/8" (67mm) 2 5/8" (67mm) 2 5/8" (67mm)

Qty. Per. Pack. 3 3 3 3 3

CODE # 96-4 96-6 96-8 96-10 96-12

90 Degree Length (a) 31 5/8" (803mm) 31 5/8" (803mm) 33 5/8" (854mm) 35 5/8" (905mm) 37 5/8" (956mm)

Form Unit Length (b) 15 5/8" (397mm) 15 5/8" (397mm) 17 5/8" (448mm) 19 5/8" (498mm) 21 5/8" (549mm)

Width 9 1/4" (235mm) 11 1/4" (286mm) 13 1/4" (337mm) 15 1/4" (387mm) 17 1/4" (438mm)



CODE # 90-4 90-6 90-8 90-10 90-12

(a)

(b)

45 Degree Length (a) 26 1/2" (673mm) 26 1/2" (673mm) 26 1/2" (673mm) 28 1/2" (724mm) 30 1/2" (775mm)

Form Unit Length (b) 10 1/2" (267mm) 10 1/2" (267mm) 10 1/2" (267mm) 12 1/2" (318mm) 14 1/2" (368mm)

Width 9 1/4" (235mm) 11 1/4" (286mm) 13 1/4" (337mm) 15 1/4" (387mm) 17 1/4" (438mm)



CODE # 45-4 45-6 45-8 45-10 45-12

One Sided Length 48" (1219mm) 48" (1219mm) 48" (1219mm) 48" (1219mm) 48" (1219mm)

Tapered Top Width 9 1/4" (235mm) 11 1/4" (286mm) 13 1/4" (337mm) 15 1/4" (387mm) 17 1/4” (438mm)

Form Unit Height 18" (457mm) 18" (457mm) 18" (457mm) 18" (457mm) 18" (457mm)



CODE # TT-P TT-6 TT-8 TT-P TT-P

(a)(b)

48” Molded Length 48" (1219mm) 48" (1219mm) 48" (1219mm) 48" (1219mm) 48" (1219mm)

Brick Ledge Width (a) 13 3/4" (349mm) 15 3/4" (400mm) 17 3/4" (451mm) 19 3/4" (502mm) 21 3/4" (552mm)

Form Unit Width (b) 9 1/4" (235mm) 11 1/4" (286mm) 13 1/4" (337mm) 15 1/4" (387mm) 17 1/4"( 438mm)



CODE # BR96-P BR96-6 BR96-8 BR96-P BR96-P

(b)

(a)

Product Image Feature 4" (100mm) 6"(150mm) 8"(200mm) 10"(250mm) 12"(300mm)

Custom Radius Length 96" (2438mm) 96" (2438mm) 96" (2438mm) 96" (2438mm) 96" (2438mm)

Form Unit Width 9 1/4" (235mm) 11 1/4" (286mm) 13 1/4" (337mm) 15 1/4" (387mm) 17 1/4" (438mm)


Radius M A N U F A C T U R E D T O S P E C I F I C A T I O N S

Qty. Per. Pack. D E P E N D S O N Q U A N T I T Y O R D E R E D

CODE # RAD-4 RAD-6 RAD-8 RAD-10 RAD-12

96” Molded Length 96" (2438mm) 96" (2438mm) 96" (2438mm) 96" (2438mm) 96" (2438mm)

Brick Ledge Width (a) 13 3/4" (349mm) 15 3/4" (400mm) 17 3/4" (451mm) 19 3/4" (502mm) 21 3/4" (552mm)

Form Unit Width (b) 9 1/4" (235mm) 11 1/4" (286mm) 13 1/4" (337mm) 15 1/4" (387mm) 17 1/4"( 438mm)



CODE # BR96-P BR96-6 BR96-8 BR96-P BR96-P

(b)

(a)

3Corporation


All specifications are for reference purposes only. Refer to the NUDURA® technicalpublications for more accurate dimensions.

Units come pre-assembled with folding, metal-hinged webs.

Units come pre-assembled with folding, slide-in webs.

Units come unassembled and require webs to be purchased separately.

(a) (b)

Unassembled Length (a) 96"(2438mm) 96"(2438mm) 96"(2438mm) 96"(2438mm) 96"(2438mm)

Standard Unit Length (b) 96"(2438mm) 96"(2438mm) 96"(2438mm) 96"(2438mm) 96"(2438mm)




CODE # PANEL PANEL PANEL PANEL PANEL

2 Standard Panels

webs not included

Unassembled Length (a) 48" (1219mm) 48" (1219mm) 48" (1219mm) 48" (1219mm) 48" (1219mm)

Tapered Top Length (b) 48" (1219mm) 48" (1219mm) 48" (1219mm) 48" (1219mm) 48" (1219mm)

Unit Height 18" (457mm) 18" (457mm) 18" (457mm) 18" (457mm) 18" (457mm)



CODE # TT-P TT-P TT-P TT-P TT-P

(a) (b)

1 Standard Panel,

1 Standard TaperedTop Panel

webs not included


Brick Ledge Length (b) 48" (1219mm) 48" (1219mm) 48" (1219mm) 48" (1219mm) 48" (1219mm)

Unit - 48” Height 18" (457mm) 18" (457mm) 18" (457mm) 18" (457mm) 18" (457mm)



CODE# BR48-P BR48-P BR48-P BR48-P BR48-P

(a) (b)


Brick Ledge Length (b) 96" (2438mm) 96" (2438mm) 96" (2438mm) 96" (2438mm) 96" (2438mm)

Unit - 96” Height 18" (457mm) 18" (457mm) 18" (457mm) 18" (457mm) 18" (457mm)




(a) (b)

1 Standard Panel,

1 Standard Brick Ledge Panel

webs not included

1 Standard Panel,

1 Standard Brick Ledge Panel

webs not included

Brick Ledge Length 32" (813mm) 32" (813mm) 32" (813mm) 32" (813mm) 32" (813 mm)

Extension Width 4 1/2" (114mm) 4 1/2" (114mm) 4 1/2" (114mm) 4 1/2" (114mm) 4 1/2" (114mm)


Qty. Per. Pack. 14 14 14 14 14

CODE # BRICK BRICK BRICK BRICK BRICK

Qty. Per. Pack. 100 screws/100 washers 100 screws/100 washers 100 screws/100 washers 100 screws/100 washers 100 screws/100 washers

CODE # SC-WA SC-WA SC-WA SC-WA SC-WA

End Cap Width 4" (102mm) 6" (152mm) 8" (203mm) 10" (254mm) 12" (305mm)



WITH FASTENING STRIP Qty. Per. Pack. 50 40 40 35 30

CODE # ECF-4 ECF-6 ECF-8 ECF-10 ECF-12


Height Length 32" (813mm) 32" (813mm) 32" (813mm) 32" (813mm) 32" (813mm)

Adjuster Height 3" (76mm) 3" (76mm) 3" (76mm) 3" (76mm) 3" (76mm)

Qty. Per. Pack. 80 80 80 80 80WITH FASTENING STRIP

CODE # HADJ-F HADJ-F HADJ-F HADJ-F HADJ-F

Washer/6” (152mm)Screw Kit

4 Corporation


Height Qty. Per. Pack. 160 160 80 80 80

Adjuster Tie CODE # HA-T-4 HA-T-6 HA-T-8 HA-T10 HA-T12

Slide-in Webs Qty. Per. Pack. 1100 655 455 410 350

CODE # WEB4 WEB6 WEB8 WEB10 WEB12

Qty. Per. Pack. 100 100 100 100 100

CODE # WEB-4 WEB-6 WEB-8 WEB-10 WEB-12

Form Lock Length 120” (3048mm) 120” (3048mm) 120” (3048mm) 120” (3048mm)

Width 6” (150mm) 8” (200mm) 10” (250mm) 12” (300mm)

Qty. Per. Pack. (10 pcs) 100' (30.5m) 100' (30.5m) 100' (30.5m) 100'(30.5m)

CODE # BLOK06 BLOK08 BLOK10 BLOK12

Not Available in 4”

8 1/2” Vertical Length 8 1/2” (216mm) 8 1/2” (216mm) 8 1/2” (216mm) 8 1/2” (216mm)

Joint Clip Qty. Per. Pack. (10 pcs) 200 200 200 200

CODE # VJC-S VJC-S VJC-S VJC-S


Insert Plate Qty. Per. Pack. 50 50 50 50 50

CODE # ICFHIP ICFHIP ICFHIP ICFHIP ICFHIP

4-Way Web Qty. Per. Pack. - - - - 100Connector

CODE # - - - - 4XWEBC

Stamped Qty. Per. Pack. 25 25 25 25 25Bearing

CODE # ICFSBB ICFSBB ICFSBB ICFSBB ICFSBB

Retrofit Qty. Per. Pack. 12 12 12 12 12Bracket

CODE # ICFRFB ICFRFB ICFRFB ICFRFB ICFRFB

Transition Qty. Per. Pack. 100 100 100 100 100 Bracket

CODE # TRA-BR TRA-BR TRA-BR TRA-BR TRA-BR

10 x 2” (51mm) Hex Qty. Per. Box. 500 500 500 500 500 Head Screw with

CODE # SC-2.0 SC-2.0 SC-2.0 SC-2.0 SC-2.0Steel Flat Washer

10 x 2.5” (63mm) Hex Qty. Per. Box. 500 500 500 500 500 Head Screw with


10 x 3” (76mm) Hex Qty. Per. Box. 500 500 500 500 500 Head Screw with


All specifications are for reference purposes only. Refer to the NUDURA® technical publications for more accurate dimensions.

Units come pre-assembled with folding, metal-hinged webs.

Units come pre-assembled with folding, slide-in webs.

Units come unassembled and require webs to be purchased separately.

8 3/4” Vertical Length 8 3/4” (222mm) 8 3/4” (222mm) 8 3/4” (222mm) 8 3/4” (222mm)

Joint Clip Qty. Per. Pack. (10 pcs) 200 200 200 200

CODE # VJC-L VJC-L VJC-L VJC-L

5Corporation

PANEL ASSEMBLY

PRODUCTS USED TO ASSEMBLE:


Molded Brick Length 96" (2438mm) 96" (2438mm) 96" (2438mm) 96" (2438mm) 96" (2438mm)

Ledge and Width (a) 13 3/4” (349mm) 15 3/4” (400mm) 17 3/4” (451mm) 19 3/4 (502mm) 21 3/4 (552mm)

Tapered Top Width (b) 9 1/4" (235mm) 11 1/4" (286mm) 13 1/4" (337mm) 15 1/4" (387mm) 17 1/4” (438mm)



Unassembled Quantity Per. Unit 1 panel 1 panel 1 panel 1 panel 1 panelTapered Top Panel * Qty. Per. Pack. 6 6 6 6 6


Unassembled Quantity Per. Unit 1 panel 1 panel 1 panel 1 panel 1 panelBrick Ledge Qty. Per. Pack. 2 2 2 2 2Panel *


Slide-in Webs * Quantity Per. Unit 6 6 6 6 6

Min. Qty. Per. Pack. 100 100 100 100 100



Unassembled Quantity Per. Unit 2 panels 2 panels 2 panels 2 panels 2 panelsBrick Ledge Qty. Per. Pack. 2 2 2 2 2Panel * CODE # BR96-P BR96-P BR96-P BR96-P BR96-P


Min. Qty. Per. Pack. 100 100 100 100 100CODE # WEB-4 WEB-6 WEB-8 WEB-10 WEB-12


(a)

(b)

Unassembled Quantity Per. Unit 2 panels 2 panels 2 panels 2 panels 2 panelsTapered Top Panel * Qty. Per. Pack. 6 6 6 6 6



Min. Qty. Per. Pack. 100 100 100 100 100


*ENSURE EXTRA WEBS ARE ORDERED TO USE THE 48" STANDARD PANELS - SEE SPECIFICATIONS IN THE "INSULATED CONCRETE FORMS" SECTION.

*ENSURE EXTRA WEBS ARE ORDERED TO USE THE 96"(2438mm)STANDARD PANELS - SEE SPECIFICATIONS IN THE "INSULATED CONCRETE FORMS" SECTION.

*ENSURE EXTRA WEBS ARE ORDERED TO USE THE 96"(2438mm)STANDARD PANELS - SEE SPECIFICATIONS IN THE "INSULATED CONCRETE FORMS" SECTION.


Double Sided Length 96" (2438mm) 96" (2438mm) 96" (2438mm) 96" (2438mm) 96" (2438mm)

Molded Brick Width (a) 17 3/4” (451mm) 19 3/4” (502mm) 21 3/4” (552mm) 23 3/4 (603mm) 25 3/4 (654mm)

Ledge Unit Width (b) 9 1/4" (235mm) 11 1/4" (286mm) 13 1/4" (337mm) 15 1/4" (387mm) 17 1/4” (438mm)



All specifications are for reference purposes only. Refer to the NUDURA® technical publications for more accurate dimensions.

NOTE: The unassembled panel units used to assemble these forms include an equal number of 96” (2438mm) standard panels (NOT SHOWN).

(a)

(b)


Two Sided Length 48" (1219mm) 48" (1219mm) 48" (1219mm) 48" (1219mm) 48" (1219mm)

Tapered Top Width 9 1/4" (235mm) 11 1/4" (286mm) 13 1/4" (337mm) 15 1/4" (387mm) 17 1/4”(438mm)


EPS Thickness 2 5/8" (67mm) 2 5/8" (67mm) 2 5/8" (67mm) 2 5/8" (67mm) 2 5/8" (67mm)*(Field assembled using 1 sided tapered top units)

6 Corporation

T FORM UNITS

(A)(A1)

(B)

(C)

(B1)(C1)

The Long “T”The Short “T”

Corporation

PRODUCT MAIN - 4” (100mm) MAIN - 6” (150mm) MAIN - 8” (200mm) MAIN - 10” (250mm) MAIN - 12” (300mm)

“T” - 4”(100mm)

“T” - 6”(150mm)

“T” - 8”(200mm)

“T” - 10”(250mm)

“T” - 12”(300mm)

A . . . . . . . . . . . . . . . 18" (457mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 50" (1270mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft./ Unit. . . 11 1/2 (1.068m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . . T4-M4

A . . . . . . . . . . . . . . . 20" (508mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 52" (1321mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq. Ft. / Unit . . . . . 12 (1.115m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . . T6-M4

A . . . . . . . . . . . . . . . 22" (559mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 54" (1372mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft. / Unit . . 12 1/2 (1.161m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . . T8-M4

A . . . . . . . . . . . . . . . 24" (610mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 56" (1422mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq. Ft. / Unit . . . . . 13 (1.208m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . T10-M4

A . . . . . . . . . . . . . . . 26" (660mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 58" (1473mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft. / Unit . . 13 1/2 (1.254m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . T12-M4

A . . . . . . . . . . . . . . . 18" (457mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 50" (1270mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft./ Unit. . . 11 1/2 (1.068m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . . T4-M6

A . . . . . . . . . . . . . . . 20" (508mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 52" (1321mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq. Ft. / Unit . . . . . 12 (1.115m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . . T6-M6

A . . . . . . . . . . . . . . . 22" (559mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 54" (1372mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft. / Unit . . 12 1/2 (1.161m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . . T8-M6

A . . . . . . . . . . . . . . . 24" (610mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 56" (1422mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq. Ft. / Unit . . . . . 13 (1.208m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . T10-M6

A . . . . . . . . . . . . . . . 26" (660mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 58" (1473mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft. / Unit . . 13 1/2 (1.254m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . T12-M6

A . . . . . . . . . . . . . . . 18" (457mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 50" (1270mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft./ Unit. . . 11 1/2 (1.068m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . . T4-M8

A . . . . . . . . . . . . . . . 20" (508mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 52" (1321mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq. Ft. / Unit . . . . . 12 (1.115m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . . T6-M8

A . . . . . . . . . . . . . . . 22" (559mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 54" (1372mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft. / Unit . . 12 1/2 (1.161m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . . T8-M8

A . . . . . . . . . . . . . . . 24" (610mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 56" (1422mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq. Ft. / Unit . . . . . 13 (1.208m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . T10-M8

A . . . . . . . . . . . . . . . 26" (660mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 58" (1473mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft. / Unit . . 13 1/2 (1.254m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . T12-M8

A . . . . . . . . . . . . . . . 18" (457mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 50" (1270mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft./ Unit. . . 11 1/2 (1.068m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . T4-M10

A . . . . . . . . . . . . . . . 20" (508mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 52" (1321mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq. Ft. / Unit . . . . . 12 (1.115m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . T6-M10

A . . . . . . . . . . . . . . . 22" (559mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 54" (1372mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft. / Unit . . 12 1/2 (1.161m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . T8-M10

A . . . . . . . . . . . . . . . 24" (610mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 56" (1422mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq. Ft. / Unit . . . . . 13 (1.208m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code #. . . . . . . . . . . . . . . T10M10

A . . . . . . . . . . . . . . . 26" (660mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 58" (1473mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft. / Unit . . 13 1/2 (1.254m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code #. . . . . . . . . . . . . . . T12M10

A . . . . . . . . . . . . . . . 18" (457mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 50" (1270mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft./ Unit. . . 11 1/2 (1.068m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . T4-M12

A . . . . . . . . . . . . . . . 20" (508mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 52" (1321mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq. Ft. / Unit . . . . . 12 (1.115m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . T6-M12

A . . . . . . . . . . . . . . . 22" (559mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 54" (1372mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft. / Unit . . 12 1/2 (1.161m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code # . . . . . . . . . . . . . . . T8-M12

A . . . . . . . . . . . . . . . 24" (610mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 56" (1422mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq. Ft. / Unit . . . . . 13 (1.208m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code #. . . . . . . . . . . . . . . T10M12

A . . . . . . . . . . . . . . . 26" (660mm)

B. . . . . . . . . . . . . 4 3/8" (111mm)

C. . . . . . . . . . . . 20 3/8” (518mm)

A1. . . . . . . . . . . . . 58" (1473mm)

B1 . . . . . . . . . . 20 3/8” (518mm)

C1. . . . . . . . . . . . 4 3/8” (111mm)

Height. . . . . . . . . . 18" (457mm)

Sq.Ft. / Unit . . 13 1/2 (1.254m2)

Qty./ Package. . . . . . . . . . . . . . . 2

Code #. . . . . . . . . . . . . . . T12M12

7Corporation

CEILING AND FLOORING TECHNOLOGY

96” (2438mm)

48” (1219mm) CEILING TECHNOLOGY

FLOORING TECHNOLOGY

WOOD STRAPPING A SHEET SIZE QTY. PER BUNDLE CODE

NO 2 1/2” (64mm) 48”x 96” (1219mm x 2438mm) 12 / BUNDLE P9-080NO 3 1/2” (89mm) 48”x 96” (1219mm x 2438mm) 5 / BUNDLE P9-100YES 3 1/2” (89mm) 48”x 96” (1219mm x 2438mm) 4 / BUNDLE P9-040YES 2 1/2” (64mm) 48”x 96” (1219mm x 2438mm) 6 / BUNDLE P9-050

A TYPE 2-GREEN SIZE QTY. PER BUNDLE CODE1 1/4” (32mm) OVER LAP 24”x 96” (610mm x 2438mm) 16 / BUNDLE P2-4351 7/8” (48mm) T&G 24”x 96” (610mm x 2438mm) 11 / BUNDLE P2-4452 1/2” (64mm) T&G 24”x 96” (610mm x 2438mm) 8 / BUNDLE P2-455

#10 SCREWS SIZE QTY. PER BOX CODE

4” (102mm) 1000 / BOX P1-0255” (127mm) 500 / BOX P0-041

A TYPE 1-BLUE SIZE QTY. PER BUNDLE CODE1 1/4” (32mm) OVER LAP 24”x 96” (610mm x 2438mm) 16 / BUNDLE P1-4701 7/8” (48mm) T&G 24”x 96” (610mm x 2438mm) 11 / BUNDLE P1-4712 1/2” (64mm) T&G 24”x 96” (610mm x 2438mm) 8 / BUNDLE P1-472

96” (2438mm)

24” (610mm)

8 Corporation

ALIGNMENT SYSTEMS

WALL CHANNELS

8’ (2438mm) Code CHA-810’ (3048mm) Code CHA-10

NUDURA® ALIGNMENT SYSTEM Code BRAC-3

Each NUDURA® Alignment System Kit (set of 20) Contains:20 Guardrail Posts20 Catwalk Brackets20 Turnbuckles

TALL WALL ADAPTER KIT Code TW-KIT

Each Tall Wall Adapter Kit (set of 20) Contains:20 Scaffold to Turnbuckle Adapters20 Channel to Scaffold Adapters10 Scaffold to Scaffold Adapters

TALL WALL CONNECTOR WIRES14” (356mm)Code TWCW14

Each Tall Wall Connection Wire Kit Contains:100 Wires

NUTS AND CROSS BRACESCode NUT-CR

Each Nuts and Cross Braces Kit Contains:50 Cross Braces100 Nuts

Guardrail Post

Catwalk Bracket

Channel

Channelto ScaffoldAdapter

Scaffoldto ScaffoldAdapter

Scaffoldto TurnbuckleAdapter

Tall Wall Connection Wire (14")

Cross Brace

Nuts

Turnbuckle

- 14” (356mm)

All specifications are for reference purposes only.Refer to the NUDURA® technical publications formore accurate dimensions.

ACCESSORIES

TRANSITION BRACKET

Code

TRA-BRQty. per Bundle/Box

100/PKG

8 1/2” (216mm)VERTICAL JOINT CLIP

Code VJC-SQty. per Box 200

8 3/4” (222mm)VERTICAL JOINT CLIP

Code VJC-LQty. per Box 200

10 X 2” (51mm)HEX HEAD SCREWS WITHSTEEL FLAT WASHER Code SC-2.0Qty. per Box 500

10 X 2.5” (63mm)HEX HEAD SCREWS WITHSTEEL FLAT WASHER Code SC-2.5Qty. per Box 500

10 X 3” (76mm)HEX HEAD SCREWS WITHSTEEL FLAT WASHER Code SC-3.0Qty. per Box 500

4-WAY WEB CONNECTOR

Code

4XWEBCQty. per Bundle/Box

100/PKG

9Corporation

ACCESSORIES

4” PROTECTIVE TAPE4”X 260’ (96MM X 66M)

Code

TAPE-4Qty. per Bundle/Box

24/BOX

FIBRE MESH-475 SQ. FT.

Code

MESHQty. per Bundle/Box

1 EACH/ROLL - 36/SKID

PARGING-75 SQ. FT.

Code

PARGQty. per Bundle/Box

1 EACH/BAG - 60/SKID

V-STRIP - BRICK LEDGE EXT.ACCESSORY 10 ‘ LONG

Code

STRIPQty. per Bundle/Box

10 PCS. (100 FT’) /BUNDLE

EASY BUCK - 10’ LONG

Code

WBUCKQty. per Bundle/Box

10 PCS. (100 FT’) /BUNDLE

SURE SHOOTER FOAM GUNwith plastic handleCode GUNQty. per Bundle/Box 1 EACH/BOX

ECONO GUN II FOAM GUNwith metal handleCode GUN-MQty. per Bundle/Box 1 EACH/BOX

REBAR BENDER CUTTER

Code

RBCQty. per Bundle/Box

1 EACH/BOX

FOAM GUN CLEANER-12OZ (340G)

Code

FOAMQty. per Bundle/Box

12/BOX

WATERPROOFINGMEMBRANE-225 SQ. FT.Code WPROFQty. per Bundle/Box 1 EACH/ROLL - 36/SKID

LOW TEMPERATURE WATERPROOFING-225 SQ. FT.Code WPROF-2Qty. per Bundle/Box 1 EACH/ROLL - 36/SKID

NUDURA® LOWEXPANSION FOAM-750ML(800G)

Code

FOAMQty. per Bundle/Box

12/BOX

FIBRE TAPE1”X 220’ (24MM X 55M)

Code

TAPEQty. per Bundle/Box

24/BOX

MULTI PURPOSEANCHOR HANGER SYSTEM

ICF HANGER INSERT PLATECode ICFHIPQty. per Bundle/Box 50/BOX

STAMPED BEARING BRACKETCode ICFSBBQty. per Bundle/Box 25/BOX

All photos above are for reference only. Actual products may vary.

NUDURA® CONCRETEVIBRATOR

Code

VIBRATEQty. per Bundle/Box

1 EACH/BOX

Corporation10

The NUDURA® Wall System is an insulated concrete formutilized in all types of construction. NUDURA® Corporationis pleased to introduce the molded Brick Ledge Extension(BLE), which can be used on all wall cores.

1. Establish the height for the brick ledge extension to be installed.Remember, the BLE can be installed in step increments or on anydesired angle (see back).

3. Chalk all three lines. The upper two are the cut lines. Cut verticallyon each side of the web to create a pocket 6” (152mm) wide. Cutout EPS pocket. The lower horizontal cut should be on an angle (45 degrees) to facilitate the concrete placement. Key hole saw,reciprocating saw or hot knife are best for this task.

4. Fasten starter strip on the bottom line with drywall screws at 16” (406mm) c/c.

2. Measure down from the established brick ledge elevation10” (254mm) and 13” (330mm).

The various form units have cores of 4” (102mm), 6” (152m),8” (203mm), 10” (254mm) and 12” (305mm), with an overall thicknessof 9 1/4” (235mm), 11 1/4” (286mm), 13 1/4” (337mm), 15 1/4” (387mm)and 17 1/4” (438mm) respectively. The BLE can be used at anyelevation on the wall on either side. The form is 32” (813mm) long x 13 1/2” (343mm) deep.

Step of any height increments in the BLE can accommodate any brickor stone size. This feature can prove to be very useful for supportingentry slabs and other applications. It should be noted that differentelevations will require different stirrups.

Steps to Follow:

BRICK LEDGE EXTENSION - Technical Bulletin

Corporation 11

REBAR PLACEMENT When placing rebar it is recommended to usethe lower position on the opposite side of the BLE. A contact spliceshould be used to maintain the bar alignment.This practice will keepthe stirrup length uniform. The #3 or #4 bar (10M bar) in the BLE is asupport bar for the stirrup, it is not required to overlap this bar. End toend splices are acceptable. (See 6. and 7.)

5. Place BLE molded form in starter strip. Attach using two No. 10 x 6”(152mm) screws with polypropylene washer for EPS. The fastenershould be attached 8” (203mm) from the end of the molded formresulting in 16”(406mm) c/c.

ORDERS AND PACKAGINGThere are 14 brick ledge extensions in a package.The starter strips aresold in packages of 100’ (30.5m) (10 lengths of 10’ (3.05m)). The 6” (152mm) fastening screws (No. 10) and the polypropylene washerscome in boxes of 100 sets.

ADDITIONAL APPLICATIONS

BRICK LEDGE EXTENSION - Technical Bulletin

6. CONCRETE PLACEMENTAn ICF concrete mix with a slump of 5” (127mm) to 6” (152mm) isrecommended. Concrete should be placed in lifts of 3’ (0.9m) to 4’(1.22m) to approximately 1’ (305mm) over the BLE elevation.

7. CONSOLIDATION Internal or external vibration can be used toconsolidate the concrete. A 1” (25mm) vibrator inserted in the brickledge extension will be most effective without increasing formpressure in the pocket. A NUDURA® External Air-Driven vibrator withaccessory attached can also be used to achieve properconsolidation.

Corporation12

FLOOR TECHNOLOGY - Technical Bulletin

PRODUCT FEATURES:

2’ (610mm)

11⁄4” (32mm), 17⁄8” (48mm),or 21⁄2” (63mm)

8’ (2438 mm)

Molded ExpandedPolystyrene Foam(Available in Type 1and Type 2 EPS)

Tongue and Groove Interlock

Ship Lap

(11⁄4” (32mm) product is ship lapped on four sides)

TYPICAL NUDURA® CROSS SECTION:

13Corporation

FLOOR TECHNOLOGY - Technical Bulletin

SUPERIOR PERFORMANCE

“NUDURA® Floor Technology is a durable and effective underslab insulation that is fast and economical to install.”

• Unique ship lap and tongue and groove integrity – no gaps and fast and easy installation• Durable molded sheets resist the cracking and crumbling associated with wire cut products.• Cost effective under-slab insulation performance.• Contains no potentially harmful CFC’s or HCFC’s.• Safe Handling• 100% recyclable

Physical Properties of ASTM Test ULC S701-97 NUDURA® Floor ULC S701-97 NUDURA® Floormolded EPS insulation Method Requirements Technology Requirements Technology

(Type 1) Type 1 (Type 2) Type 2

Thermal Resistance (1” thick) min.: 3.7 3.82 min.: 4.0 4.05hr.ft2.ºF/BTU (m2.ºK/w)

C-518(min.: 0.65) (0.67) (min.: 0.70) (0.708)

Water Vapor Permeability max.: 5.3 0.70 max.: 3.5 0.60Perm. (ng/Pa.s.m2)

E-96(max.: 300) (40) (max.: 200) (35)

Dimensional Stability % D-2126 max.: 1.5 1.0 max.: 1.5 1.0

Flexural Strength min.: 25 80 min.: 35 84lbs/ft2 (kPa)

C-203(min.: 170) (550) (min.: 240) (575)

Water Absorption % D-2842 max.: 6.0 1.8 max.: 4.0 1.8

Compression Strength min.: 10 14 min.: 16 19lbs/ft2 (kPa)

D-1621(min.: 70) (97) (min.: 110) (131)

Oxygen Limit Indication % D-2863 min.: 24 42 min.: 24 41

1) Level the granular base to receive the panels.

2) Install panels against one wall, with the labelling upwards,making sure that the end of the panel with the ship lap is at the bottom to receive the next panel.

3) Once the pattern is established, use the orientation of the labelling to maintain the pattern.

4) It is recommended to stagger the 2’ (610mm) seams.This is easily achieved by starting the second row with the leftover cut panel from the first row.This method will result in virtually no material waste.

• Two lines of NUDURA® Floor Technology are available – Type 1 EPS and Type 2 EPS.

• Available in 1 1/4” (32mm), 1 7/8” (48mm), or 2 1/2” (63mm) thicknesses.

• NUDURA® Floor Technology can also be custom manufactured at higher densities to meet job-specific requirements.

• Packaging Thickness Pieces/Bundle1 1/4” (32mm) 171 7/8” (48mm) 112 1/2” (63mm) 8

TECHNICAL DATA

INSTALLATION INSTRUCTIONS

PACKAGING AND ORDERING

14 Corporation

CEILING TECHNOLOGY - Technical Bulletin

“NUDURA® Ceiling Technology is a high performance insulation system that reduces air infiltration and thermal bridging.”

• Fast and easy mechanical attachment to trusses is provided by the embedded wood strapping• The 11⁄2” (38mm) perimeter overlap reduces air infiltration• A vapor barrier is not required• Contains no potentially harmful CFC’s or HCFC’s• Safe Handling• 100% recyclable• A quick and economical insulation solution for retro-fitting uninsulated floors, walls and ceilings in homes,

garages, cottages or commercial buildings

4’ (1219mm)

21⁄2” (63mm) or31⁄2” (89mm)

Embedded wood strapping @ 16” (406mm) O/C

11⁄2” (38mm) overlap at perimeter

Type 1 ExpandedPolystyrene Foam

8’ (2438m

m)

PRODUCT FEATURES


TYPICAL NUDURA™™ CROSS SECTION

15Corporation

Physical Properties of ASTM Test ULC S701-97 NUDURA® Ceilingmolded EPS insulation Method Requirements Technology

(Type 1) Type 1

Thermal Resistance (1” thick) min.: 3.7 3.82hr.ft2.ºF/BTU (m2.ºK/w)

C-518(min.: 0.65) (0.67)

Water Vapor Permeability max.: 5.3 0.70Perm. (ng/Pa.s.m2)

E-96(max.: 300) (40)

Dimensional Stability % D-2126 max.: 1.5 1.0

Flexural Strength min.: 25 80lbs/ft2 (kPa)

C-203(min.: 170) (550)

Water Absorption % D-2842 max.: 6.0 1.8

Compression Strength min.: 10 14lbs/ft2 (kPa)

D-1621(min.: 70) (97)

Oxygen Limit Indication % D-2863 min.: 24 42

1) Install one layer of gypsum board to the underside of the trusses, taping is not required.Alternative sheeting materials can be used to create the sandwich effect. Gypsum isrecommended for the layer where adjacent space needs a thermal barrier as per local coderequirements.

2) Install an air shield along the perimeter of the building at the wall and ceiling joint. The 6 milpoly barrier should cover a minimum of 8” (203mm) of the wall and 8” (203mm) of the ceilingboard.

3) Install the first layer of NUDURA® Ceiling Technology perpendicular to the trusses using 5” (127mm) screws @ 24” (610mm) o/c.

4) Install 1” x 4” (19mm x 89mm) lumber along the perimeter of the building on the wall andunder the first layer of NUDURA® Ceiling Technology.This will provide a nailing surface for thegypsum board.

5) Install the second layer of NUDURA® Ceiling Technology perpendicular to the first layer using 5” (127mm) screws at 16” (406mm) o/c.

6) Install gypsum board perpendicular to the embedded wood strapping using drywall screws asper local code requirements.

• Available in 2 1⁄2” (63mm) and 3 1⁄2” (89mm) thicknesses.• Packaging Thickness Pieces/Bundle

2 1⁄2” (63mm) 73 1⁄2” (89mm) 5

TECHNICAL DATA



CEILING TECHNOLOGY - Technical Bulletin

16 Corporation


• NUDURA® brand Waterproofing Membrane is a peel and stick membrane that adheresto NUDURA® expanded polystyrene (EPS) foam.

• The membrane satisfies damp proofing and water proofing requirements for allbuilding codes in North America.

• A 3” (76mm) wide hand roller is available and recommended to ensure that theadhesive side of the membrane is fully and properly affixed to the foam. NUDURA®makes available both summer and winter grade membrane as seasonaltemperatures dictate. Be sure you qualify with your distributor which grade yourequire at time of ordering.

DELIVERY AND SITE CONSIDERATIONS

• Care should be taken to protect the material on site from moisture, dust andgeneral wear and tear. Store rolls in a cool, dry location, not in direct groundcontact and protect with a tarp to prevent exposure until ready to use.

• Working temperature range should ideally be between 35ºF and 100ºF (2ºC and 38º C) Note: if below this range or other special conditions such as air borne dustexist on site, consider using an adhesion primer **available from your NUDURA®distributor**. To maximize primerless adhesion on colder days, store the materialin a heated location on site until needed. (A heat gun can also be used to assist inapplication).

• NUDURA® Waterpproofing Membrane should not be exposed to sunlight forextended periods of time. Backfilling should take place within 1 week of installingthe membrane. If daytime temperature exceeds 80ºF (27ºC) after installation,NUDURA® recommends shading the applied membrane temporarily untilbackfilling is completed.

SITE PREPERATION

1. Ensure that the wall surface is smooth, dry, free from dust, dirt and any otherimpurities that could be on the wall.

2. If the EPS foam surface has been exposed to sunlight for extended periods of time,the resulting yellow dust coating must be fully removed in order for the membraneto adhere properly.

NOTE:Installation works most efficiently with a 2 person work crew - one handling thematerial from each side. The most efficient method of installation (as described inthis bulletin) is vertical application of the sheets with 2" (51mm) overlaps at the sidesof the material. If horizontal application of the material is preferred or required insome locations, be sure to work from the bottom of the wall to the top and lapmaterial a minimum of 6” (152mm) in shingle fashion so that water is sheddownward and OVER the layer below.

WATERPROOFING MEMBRANE - Technical Bulletin

17Corporation


1. Establish the finished grade around the entire perimeter of thebuilding using a chalk line and/or marker.

2. Begin material installation by first cutting strips of membrane 16”(406mm) to 24” (610mm) wide. These will be used to pre-seal allinside and outside corner conditions. Fold strips in half vertically.

3. At each inside corner, starting at the footing level, peel releasepaper away and apply the strips in a shingle like fashion from thebase to the top of the corner, installing the strips vertically so thatan equal amount of material is applied to either side of the corner.Take care to press the fold tightly into the corner so that no airpockets are trapped behind - then press or roll the membrane flatto the wall surfaces on either side using a plastic roller as necessary.Each strip of material should lap the strip below it by 6” (152mm)Continue application and lapping of the strips to the grade line andtrim the membrane above it.

4. Select an outside corner for the start of full membrane installationand measure the distance from the chalked grade line to the top ofthe footing. For sloping grade lines, measure to longest side of themembrane.

5. Roll out the membrane on a flat surface, then mark and cut it to therequired length.

6. Peel back the silicone release paper a distance of about 1’ (305mm)from the top edge of the cut edge of the membrane.

7. Align the top edge of the membrane with the chalk line so that oneside of the membrane extends past the corner by approx. 4” to 5"(102mm -127mm). (For sloping grade lines, lightly tack the portionof membrane above the chalk line and trim back to chalk line afterrest of memrbane is secured in place). Use the score lines in theform face as guides to keep the membrane vertical while installing.

8. While keeping the extended side of the membrane in plane withthe starting wall, firmly press it into place onto the face of the EPSfoam. Use the plastic roller to roll the membrane from the centerout to the edges to prevent any air bubbles from getting trapped.

9. Continue down the surface of the wall by further peeling back therelease paper and pressing and/or rolling the membrane intoposition as outlined in step 8. Repeat process down the length ofthe wall to the footing.

10. Now press the free 4" to 5" (102mm-127mm) side of the materialinto place down the opposing wall from the corner conditionfollowing procedure outlined in step 8.

11. For service or utility penetrations that project outward through thewall: (a) Cut a 12" x 12" (305mm x 305mm) piece of membrane-then use the pipe as a template to cut 2 cross cut slits at the centerof the piece just short of the full pipe diameter. (b) Peel the backing

paper away and slide the piece into place over the projecting pipepenetrating it through the center of the slits. (c) Press themembrane piece firmly into place, sealing the flaps against thepipe. (d) Apply the standard sheet membrane (cut to requiredlength), following the same procedures as outlined in step 8,except at the pipe location - peel back the paper clear of the pipe,lower membrane to pipe and cut a cross slit right over pipe andseal around, then continue the installation procedure

12. Should the service penetration be flush with the wall, mark thisopening to allow the following sub trade the opportunity to use it.

13. For sites with coarse backfill or risk of sharp edged aggregates,NUDURA® recommends that a backfill protection layer beinstalled over the waterproofing membrane consisting of board,heavy plastic sheet materials, fan-fold ribbed plastic board etc.

WATERPROOFING MEMBRANE - Technical Bulletin

18 Corporation

Short “T” Long “T”

These units come unassembled with all the required components.Each package of T form units come with enough components to assembletwo (2) Long “T” units and two (2) Short “T” units.

A short “T” consists of:A long “T” consists of:

(a) (d)

(b)

(c)

(b)(c)


The T form units are available to fitany combination of Main Wall Cavityand T wall cavity based on theNUDURA® five (5) standard corethicknesses. The chart to the rightshows all the possible combinationsand lists the square footage of wallcovered by one (1) Long “T” form andone (1) Short “T” form.

Main Wall Cavity

T W

all C

avit

y

Wall ft2 of form 11.50 ft2 (1.068m2) 11.50 ft2 (1.068m2) 11.50 ft2 (1.068m2) 11.50 ft2 (1.068m2) 11.50 ft2 (1.068m2)

Product Number T4-M4 T4-M6 T4-M8 T4-M10 T4-M12






Product Number T10-M4 T10-M6 T10-M8 T10M10 T10M12


Product Number T12-M4 T12-M6 T12-M8 T12M10 T12M12

4”

6”

8”

10”

12”

4” 6” 8” 10” 12”


T FORM UNITS - Technical Bulletin

19Corporation


The picture to the right demonstrates the proper assembly of a Long “T” form unit anda Short “T” form unit. The square footage calculation shown on the previous page isbased on this combination.


1. Insert webs are required.

1st Course

1. The long side of the form will be inserted into the main wall,for the 1st course.

2. The panel form on the outside of the main wall will need to be cutto accommodate the different widths of the T form.

3. Install re-bar as specified.

4. Install foam insert into the outside form to splice both pieces together.

2nd Course

1. Using the long side of the form, install into the T form to create astaggered joint.

2. Cut the outside panel and insert webs.

3. Install cut foam piece to splice the two panels together.

4. Install re-bar as specified.

5. Continue building all additional courses as per the first two.


• NUDURA® T form unit connection is available in any wall combination.

• It reduces blowouts and requires minimal labour,as no additional building is required.

• Speeds up building time and is easily installed along NUDURA® main wall.

T FORM UNITS - Technical Bulletin

T FORM CONNECTION

20 Corporation


• The NUDURA® Tall Wall Adapter Kit can be used in conjunction with standard frame scaffold.• Most common frame scaffold is 7’ (1.78m) center to center by 5’ (1.27m) high.• The NUDURA® alignment system is easily adapted to the tall wall.• Any allowable wall height can be erected using the tall wall components.

TALL WALL - Technical Bulletin

1. Before starting the first course of forms the installer needs tomeasure the width of the frame scaffold being used for the tallwall adapter kit. (fig.1)

2. Sketch a drawing of the project showing the layout for thebracing location.

3. Starting at a corner, place first course of forms.

4. Mark on forms layout locations for alignment and scaffold tobe attached to wall assembly.

5. Starting at the top of the form, at the layout locations, cut 2vertical slits into the form approximately 2”-3” (51mm - 76mm)in length. (fig. 2 & 3)

6. Hook the connection ties on the web and slide into slits.(fig. 4 & 5)

7. Repeat steps 5 & 6 for entire first course and every course untilthe first pour height has been completed. Note: NUDURA®Corporation recommends the height of the first pour notexceed the height of the box channel or frame scaffolddimensions.

8. After the third or fourth course of forms has been completedthe box channels can be placed between the connection tiesand the compression plate along with the self threading nutscan be installed. Use a 3/8” (10mm) deep socket to fasten nutsto ties. (fig. 6, 7 & 8)

9. Install adjustable diagonal brace, catwalk, and guard rail as pernormal installation procedures. The adjustable diagonal braceneeds to be anchored to the ground with proper dritt pins ormechanical fasteners to a concrete slab.

10. Complete first wall height and pour to termination stop.

11. Dismantle alignment system, removing catwalk and bracket,diagonal brace and box channel from the wall.

12. Attach frame scaffold re-using connection ties, compressionplate and self threading nuts.

13. Attach all cross bracing for frame scaffold unless otherwiseengineered. (fig. 9)

1

2

4 5

6 7

8 9

10 11

3

21Corporation

14. Insert the channel to scaffold adapter into the top of thescaffold frame leg closest to the wall and secure using a boltand nut.

15. Repeat steps 5 & 6 for installation of connection ties.

16. Slide the box channel onto the channel to scaffold adapter.Securethe box channel to the adapter inserting the 4” (102mm) boltthrough the alignment holes and tighten the nut. (fig. 10 & 11)

17. Attach the diagonal brace to scaffold adapter by inserting into thescaffold frame leg. Secure to scaffold using bolt and nut assemblyin both locations. Insert bolt and nut into location A (fig. 12) andinsert bolt and nut for location B (fig. 13).

PLEASE NOTE:All components are manufactured in accordance with engineeringdocumentation that exceeds the standards outlined in theCanadian Safety Council of Occupational Health & Safety Act andthe United States Safety Council of Occupational Safety & HealthAct. NUDURA® Corporation will not be held responsible for anymisuse or unauthorized use of the tall wall components. OHSA(Canada) or OSHA (USA) can demand site specific engineering ifthey deem necessary. NUDURA® Corporation will not beresponsible for any additional engineering costs that might bedeemed necessary for a specific project.

NUDURA® Corporation is not responsible for any site specificengineering regarding wind loading, or any improper safetyregulations; please consult with local safety regulators to ensure allregulations are met.

TALL WALL - Technical Bulletin

18. Attach diagonal brace to adapter inserting bolt and nutassembly. Install catwalk and safety guard rails as specified.(fig. 14 & 15)

19. Install all additional diagonal braces and safety guard rails asoutlined on the engineered specifications. (fig. 16 & 17)

12

14 15

1716

13

22 Corporation

The NUDURA® ICF multi-purpose anchor/hanger system is primarilyused for hanging floor joists, but can additionally be used for suchapplications as exterior deck installations, or anchoring or fastening aninterior or exterior applied frame partition wall to an ICF wall.

CONSISTS OF:• 2 stamped flat sheet plates, which can be roughly installed

within the form.


1. Determine the lowest elevation at whichthe frame members are to be set in the wall.

2. Apply a chalk line 1” (25mm) above thislowest elevation line.

3. Vertical cuts are made on either side ofthe joist or truss unit location, either fromthe top of the course down, or cuttingdirectly through the form to suit theheight of the panel being installed. (See A)

4. Do not extend the cut below the chalkline in order to provide intermediatesupport of the hanger brackets.

5. Insert each of the 2 insert plates by eithersliding them downward from the top ofthe form or inserting them horizontallythrough the form cuts, so that the largehold perforations of the brackets aresitting INSIDE the form cavity. (See B)

6. Exact placement of the insert plates willnot be crucial as long as the cuts in thefoam are made at 90º to the foam face toensure the bracket faces will always be inplane and in line with the face of the joistor truss frame. (See C)

7. After the concrete has been placed andcured enough for hanging a floor or trussmember, chalk a second line at either thetop or bottom elevation of the joist to beinstalled. This should be done with atransit or a laser level.

8. Fit the framing member stamped bearingbracket at the bottom end of the joist ortruss as shown. (See D & E)

9. Slide the joist or truss member andstamped bearing bracket down betweenform inserts plates ready for anchorage atthe desired height. (See F)

10. Once positioned so that the joist is in linewith the final chalk line, fasten throughboth the plate and bracket perforationsin an offset triangle fashion to ensuresolid anchorage of the stamped bearingbracket into position. (See G)

NOTE:If, in error, insert plates have not beeninstalled prior to concrete pour, or havebeen installed incorrectly, retrofit bracketsare available post pour.

• An adjustable stamped bearing bracket which is accurately fixedafter the concrete pour by simply screwing 3 #10 self-tapping/self-drilling screws (1.5” (38mm) in length or equivalent to the joistwidth) into each side of the joist as specified.

NOTE:It is important to establish a proper truss or floor joist layout prior toinstalling the alignment system. This ensures the bracing systemdoes not interfere with the hanger system.

MULTI PURPOSE

ANCHOR/HANGER SYSTEM - Technical Bulletin

A B C D E

F

G

23Corporation


1. Determine location where bracket is to bemounted (ie. elevation and spacing).

2. Cut away and remove foam in the insertionarea. (See A)

3. Fasten the first piece of the retrofit bracketdirectly onto the concrete using 3/8” x 4”(10mm x102mm) or 5”(127mm) wedge anchor.(See B)

4. Fasten second piece of the retrofit bracket ontothe concrete making sure to leave properspacing for the joist or truss member to beattached. (See C & D)

5. Chalk a second line at either the top or bottomelevation of the truss/joist to be installed. Thisshould be done with a transit or a laser level.

6. Fit the framing member stamped bearingbracket at the bottom end of the joist or trussas shown. (See E & F)

7. Slide the joist or truss member and stampedbearing bracket down between the foamretrofit brackets ready for anchorage at thedesired height.

8. Once positioned so that the joist is in line withthe final chalk line, fasten through both theretrofit bracket and the stamped bearingbracket perforations in an offset trianglefashion, using a #12 self tapping/self drillingscrew to ensure solid anchorage of thestamped bearing bracket into position. (See G)

9. Reinstall the displaced foam or fill the cavitywith spray foam to complete installation.

The NUDURA® retrofit bracket is used when a change or error occursafter concrete has been placed into the forms and cured. This bracketis primarily used for such applications as floor or deck connections,mono truss connections, or anchoring/fastening an interior or exteriorapplied framed partition wall to an ICF wall.

CONSISTS OF:• 2 L-shaped stamped plates which are affixed to the concrete

• 4 wedge anchors 3/8” x 4” (10mm x102mm) or 5”(127mm) inlength are also required for each set of 2 L-shaped stamped plates

NOTE: The EPS must be completely removed to expose the concretebefore attachment of the retrofit bracket to the concrete. EPS canbe reinstalled around the brackets or spray foam can be applied,once the wedge anchors have been installed and tightened.

RETROFIT BRACKET - Technical Bulletin

A

E

F

G

B C D

24 Corporation

SUPERIOR PERFORMANCEThe ICF multi-purpose anchor/hanger system is primarily used for hangingfloor joists, but can additionally be used for such applications as roof systems,exterior deck installations, or anchoring or fastening an interior or exteriorapplied frame partition wall to an ICF wall.

CONSISTS OF:2 stamped flat sheet plates, which can be roughly installed within the form and an adjustable stamped bearing bracket which is accurately fixedafter the concrete pour by simply screwing 3 #10 self-tapping/self-drillingscrews (1.5” (38mm) in length or equivalent to the joist width) into each sideof the joist as specified.

NOTE:It is important to establish a proper truss or floor joist layout prior to installingthe alignment system. This ensures the bracing system does not interfere withthe hanger system.

1. Ensure you have a proper truss layout.

2. Take special care to note any double truss or girder requirements.

3. A cut in the insert plate may be required for clearance around rebar.

4. Mount insert plates on either side of a small piece of 2x4 (38mm x 89mm) (approximately 12” (305mm) in length).

5. Determine final elevation. This may require cutting a notch in the form.

6. Immediately after concrete has been poured, embed insert plates with2x4 (38mm x 89mm) attached as per truss layout.

7. After concrete has set, remove 2x4 (38mm x 89mm) pieces. Now insert platesare ready for trusses to be inserted.

8. In most cases, screwing into the gang nailer or wood member should be adequate. (Check with local building codes).

9. In hurricane prone areas, stamped bearing bracket may need to be installed over the truss member and fastened to the insert plate.

10. Wind bracing will still be required as per engineered truss design.

ROOF/HURRICANE ANCHOR SYSTEM - Technical Bulletin

25Corporation


1. Determine the lowest elevation at which the bottomchord of the truss is to be set against the wall.

2. Apply a chalk line 1” (25mm) above this lowest elevation line.

3. Apply a second chalk line to allow positioning of theupper insert plate plum with the bottom plate, andin line with the gang nail plate at the interseting topchord of the truss.

4. Insert each of the 2 insert plates for both the top andbottom bracket locations, by either sliding themdownward from the top of the form or insertingthem horizontally through the form cuts, so that thelarge hole perforations of the brackets are sittingINSIDE the form cavity. (See A & B)

5. Exact placement of the insert plates will not becrucial as long as the cuts in the foam are made at90º to the foam face to ensure the bracket faces willalways be in plane and in line with the face of thejoist or truss frame. (See C)

6. After the concrete has been placed and cured longenough for hanging a truss member, chalk a secondline at either the top or bottom elevation of the trussto be installed. This should be done with a transit ora laser level.

7. Fit the framing member stamped bearing bracket atthe end of the truss as shown. (See D & E)

8. Install a temporary rim joist at the underside of thelowest elevation of the truss by screwing it into the

form webs.This will provide a seat for the truss to siton until fastened.

9. Slide the truss member and stamped bearingbracket down between form inserts plates ready foranchorage at the desired height. (See F & G)

10. Once the truss is seated on the rim joist, using thedesignated #10 self-tapping screws, fasten throughboth the insert plate and stamped bearing bracketperforations of the bottom bracket , as well asfastening through the insert plate, stamped bearingbracket perforations and gang nail plate at the topbracket location. (See H)

NOTE:If, in error, insert plates have not been installedprior to concrete pour, or have been installedincorrectly, retrofit brackets are available for postpour installation.

The ICF multi-purpose anchor/hanger system is primarily usedfor hanging floor joists, but can additionally be used for suchapplications as exterior deck installations, or anchoring orfastening an interior or exterior applied frame partition wall toan ICF wall.

CONSISTS OF:• 2 stamped flat sheet plates, which can be roughly installed

within the form.

• An adjustable stamped bearing bracket which is accurately fixedafter the concrete pour by simply screwing 3 #10 self-tapping/self-drilling screws (1.5” in length (38mm) or equivalent to the joistwidth) into each side of the joist as specified.

NOTE:It is important to establish a proper truss or floor joist layout prior toinstalling the alignment system. This ensures the bracing systemdoes not interfere with the hanger system.

MONOTRUSS HANGER SYSTEM - Technical Bulletin

A

F

G

H

B C D E

26 Corporation

Use NUDURA® Low Expansion Foam to:• Glue the 1st course to the footing• Shim low spots• Seal around service penetrations• Seal around doors and windows• Replace the insulation in the electrical wiring channels• Fill miscellaneous holes• Fix a broken form• Plus many, many more job site applications

“Every NUDURA® job should use a case of NUDURA® Low Expansion Foam.”

• NUDURA® Low Expansion Foam comes in 25 oz (750ml) cans and is available by the case (12 cans)

• Polyclean II Cleaner comes in 12 oz (355ml) cans and is available by the case (12 cans)

• Guns are available individually or by the case (18 guns)

LOW EXPANSION FOAM - Technical Bulletin

APPLICATIONS


• Easy to use• Teflon Coated• Molded Standard Valve fits all cans • All Metal Body and Handle

ECONO GUN IIALL METAL FOAM APPLICATOR GUN

• Easy to use• Light weight• Molded Standard Valve fits all cans

Anyone in the construction industry should have one of these!

SURE SHOOTERLIGHT WEIGHT ECONOMY FOAM APPLICATOR GUN

• Easy to install and remove collar, and fits all guns• High Yield – tested to yield up to 70% more than other name brands• Low Expansion• Extended 18 month shelf life• Formulated to be gunnable in low temperatures (to 5ºC/40ºF)• Contains no CFC’s or HCFC’s

“NUDURA® Low Expansion Foam is specially formulated to save the builder time and money when building NUDURA® Walls.”


product catalog - opico · 2008-01-14 · corporation 1 product catalog insulated concrete forms ....

Documents