probing ei3 extender board manual - analog.com · † release note containing information about the...
TRANSCRIPT
a
Probing EI3 Extender Board Manual an EZ-Extender® product
Revision 1.0, August 2012
Part Number 82-000243-01
Analog Devices, Inc.One Technology WayNorwood, Mass. 02062-9106
Copyright Information© 2012 Analog Devices, Inc., ALL RIGHTS RESERVED. This docu-ment may not be reproduced in any form without prior, express written consent from Analog Devices, Inc.
Printed in the USA.
DisclaimerAnalog Devices, Inc. reserves the right to change this product without prior notice. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use; nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by impli-cation or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark NoticeThe Analog Devices logo, Blackfin, CrossCore, EngineerZone, EZ-Board, EZ-Extender, EZ-KIT Lite, and VisualDSP++ are registered trademarks of Analog Devices, Inc.
All other brand and product names are trademarks or service marks of their respective owners.
Regulatory Compliance The Probing EI3 Extender Board is designed to be used solely in a labora-tory environment. The board is not intended for use as a consumer end product or as a portion of a consumer end product. The board is an open system design which does not include a shielded enclosure and therefore may cause interference to other electrical devices in close proximity. This board should not be used in or near any medical equipment or RF devices.
The Probing EI3 Extender Board is in the process of being certified to comply with the essential requirements of the European EMC directive 89/336/EEC (inclusive 93/68/EEC) and, therefore, carries the “CE” mark.
The extender board contains ESD (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate on the human body and equipment and can discharge without detection. Permanent damage may occur on devices subjected to high-energy discharges. Proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Store unused extender boards in the protective shipping package.
CONTENTS
PREFACE
Product Overview ........................................................................ vii
Purpose of This Manual .............................................................. viii
Intended Audience ...................................................................... viii
Manual Contents .......................................................................... ix
What’s New in This Manual .......................................................... ix
Technical Support .......................................................................... x
Supported Products ....................................................................... xi
Product Information ..................................................................... xi
Analog Devices Web Site ......................................................... xi
EngineerZone ......................................................................... xii
Related Documents ..................................................................... xiii
USING PROBING EI3 EXTENDER BOARD
Package Contents .......................................................................... 1-2
Supported Operating Systems ........................................................ 1-2
System Requirements .................................................................... 1-3
Probing EI3 Extender Board Installation ........................................ 1-3
Probing EI3 Extender Board Manual v
Contents
Expansion Interface III ................................................................. 1-4
Board Design Database ................................................................. 1-5
PROBING EI3 EXTENDER BOARD HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
Connectors ................................................................................... 2-3
Expansion Interface III (EI3) Connectors (J1–2) ...................... 2-3
Expansion Interface III (EI3) Connectors (P1–2) ..................... 2-4
Probing Connectors (P3–P6) ................................................... 2-4
Power Connector (J3) ............................................................. 2-5
LEDs ........................................................................................... 2-5
Power LED (LED1) ................................................................ 2-5
PROBING EI3 EXTENDER BOARD BILL OF MATERIALS
PROBING EI3 EXTENDER BOARD SCHEMATIC
INDEX
vi Probing EI3 Extender Board Manual
PREFACE
Thank you for purchasing the Probing EI3 Extender Board, an
EZ-Extender® product for EZ-KIT Lite®/EZ-Board® evaluation systems with the expansion interface 3 (EI3).The EZ-KIT Lite/EZ-Board and Probing EI3 Extender Board are designed to be used in conjunction with the CrossCore® Embedded Studio (CCES) development environment.
To learn more about Analog Devices development software, go to http://www.analog.com/dsp/tools.
Product OverviewThe Probing EI3 Extender Board is a separately sold daughter board that plugs onto the EI3 of an EZ-KIT Lite/EZ-Board evaluation system. The extender board aids the design and prototyping phases of embedded pro-cessor-targeted applications.
The board extends the capabilities of the evaluation system by providing a point for probing any of the signals on the Expansion Interface 3 connector.
Probing EI3 Extender Board Manual vii
Purpose of This Manual
The following is a list of the Probing EI3 Extender Board interfaces.
• 30 2 headers for probing signals
• Expansion Interface III
• No power supply required: derives power from the EZ-KIT Lite/EZ-Board
• CE certified
Purpose of This ManualThe Probing EI3 Extender Board Manual provides instructions for install-ing the product hardware (board). The text describes operation and configuration of the board components and provides guidelines for run-ning your own code on the Probing EI3 Extender Board. Finally, a schematic and a bill of materials are provided for reference.
Intended AudienceThe primary audience for this manual is a programmer who is familiar with Analog Devices processors. This manual assumes that the audience has a working knowledge of the appropriate processor architecture, instruction set, and C/C++ programming languages.
Programmers who are unfamiliar with Analog Devices processors can use this manual, but should supplement it with other texts that describe your target architecture and hardware development tools.
Programmers who are unfamiliar with the CrossCore Embedded Studio programming environment or the mating evaluation board should refer to the CCES online help.
viii Probing EI3 Extender Board Manual
Preface
Manual ContentsThe manual consists of:
• Chapter 1, “Using Probing EI3 Extender Board” on page 1-1Provides basic product information.
• Chapter 2, “Probing EI3 Extender Board Hardware Reference” on page 2-1Provides information about the product’s hardware components.
• Appendix A, “Probing EI3 Extender Board Bill Of Materials” on page A-1Provides a list of hardware components used to manufacture the board.
• Appendix B, “Probing EI3 Extender Board Schematic” on page B-1Provides all circuits on the extender board.
What’s New in This ManualThis is the first revision of the Probing EI3 Extender Board Manual.
Probing EI3 Extender Board Manual ix
Technical Support
Technical SupportYou can reach Analog Devices processors and DSP technical support in the following ways:
• Post your questions in the processors and DSP support community at EngineerZone®:http://ez.analog.com/community/dsp
• Submit your questions to technical support directly at:http://www.analog.com/support
• E-mail your questions about processors, DSPs, and tools develop-ment software from CrossCore Embedded Studio or VisualDSP++®:
Choose Help > Email Support. This creates an e-mail [email protected] and automatically attaches your CrossCore Embedded Studio or VisualDSP++ version infor-mation and license.dat file.
• E-mail your questions about processors and processor applications to: [email protected] [email protected] (Greater China support)
• In the USA only, call 1-800-ANALOGD (1-800-262-5643)
• Contact your Analog Devices sales office or authorized distributor. Locate one at:www.analog.com/adi-sales
x Probing EI3 Extender Board Manual
Preface
• Send questions by mail to:Processors and DSP Technical SupportAnalog Devices, Inc.Three Technology WayP.O. Box 9106Norwood, MA 02062-9106USA
Supported ProductsThis extender board supports EZ-KIT Lite/EZ-Board evaluation systems with the expansion interface 3.
Product InformationProduct information can be obtained from the Analog Devices Web site and the CCES online help system.
Analog Devices Web SiteThe Analog Devices Web site, www.analog.com, provides information about a broad range of products—analog integrated circuits, amplifiers, converters, and digital signal processors.
To access a complete technical library for each processor family, go to http://www.analog.com/processors/technical_library. The manuals selection opens a list of current manuals related to the product as well as a link to the previous revisions of the manuals. When locating your manual title, note a possible errata check mark next to the title that leads to the current correction report against the manual.
Also note, myAnalog is a free feature of the Analog Devices Web site that allows customization of a Web page to display only the latest information
Probing EI3 Extender Board Manual xi
Product Information
about products you are interested in. You can choose to receive weekly e-mail notifications containing updates to the Web pages that meet your interests, including documentation errata against all manuals. myAnalog provides access to books, application notes, data sheets, code examples, and more.
Visit myAnalog (found on the Analog Devices home page) to sign up. If you are a registered user, just log on. Your user name is your e-mail address.
EngineerZoneEngineerZone is a technical support forum from Analog Devices. It allows you direct access to ADI technical support engineers. You can search FAQs and technical information to get quick answers to your embedded processing and DSP design questions.
Use EngineerZone to connect with other DSP developers who face similar design challenges. You can also use this open forum to share knowledge and collaborate with the ADI support team and your peers. Visit http://ez.analog.com to sign up.
xii Probing EI3 Extender Board Manual
Preface
Related DocumentsFor additional information about the processor, refer to the following publications.
Table 1. Related Processor Publications
Title Description
Processor Data Sheet General functional description, pinout, and timing of the processor
Processor Hardware Reference Description of the internal processor archi-tecture and all register functions
Blackfin Processor Programming Reference Description of all allowed processor assembly instructions
Probing EI3 Extender Board Manual xiii
Related Documents
xiv Probing EI3 Extender Board Manual
1 USING PROBING EI3 EXTENDER BOARD
This chapter provides the setup procedure for the Probing EI3 Extender
Board and describes two types of interfaces the extender supports.The information is presented in the following order.
• “Package Contents” on page 1-2
• “Supported Operating Systems” on page 1-2
• “System Requirements” on page 1-3
• “Probing EI3 Extender Board Installation” on page 1-3
• “Expansion Interface III” on page 1-4
• “Board Design Database” on page 1-5
Probing EI3 Extender Board Manual 1-1
Package Contents
Package ContentsYour Probing EI3 Extender Board package contains the following items.
• Probing EI3 Extender Board
• A bag containing hardware for securing the extender board onto the EZ-KIT Lite/EZ-Board
• Release note containing information about the product download
Contact the vendor where you purchased your extender board or contact Analog Devices, Inc. if any item is missing.
Supported Operating SystemsCrossCore Embedded Studio is supported on the following operating systems:
• Windows® XP Professional SP3 (32-bit only)
• Windows Vista™ Business, Enterprise, or Ultimate SP2 (32-bit only)
• Windows 7 Professional, Enterprise, or Ultimate (32- and 64-bit)
Windows Vista and Windows 7 users may experience User Access Control (UAC) related errors if the software is installed into a pro-tected location, such as Program Files or Program Files (x86). We recommend installing the software in a non-UAC-protected location.
1-2 Probing EI3 Extender Board Manual
Using Probing EI3 Extender Board
System RequirementsVerify that your PC has these minimum requirements for the CCES installation:
• 2 GHz single-core processor
• 1 GB RAM
• 8 GB available disk space
• One open USB port
A faster disk drive decreases the build time, especially for a large amount of source files.
Probing EI3 Extender Board InstallationFollow these instructions to ensure correct operation of the product hard-ware and software.
1. Attach the extender board to the EZ-KIT Lite/EZ-Board.The J1 connector on the extender board can be connected to the P1A, P2A, or P3A connector on the EZ-KIT Lite/EZ-Board. Refer to the example program for a reference to the proper connector.
2. Use the provided hardware to secure the extender to the EZ-KIT Lite/EZ-Board. See Figure 1-1.
3. Refer to the EZ-KIT Lite/EZ-Board manual for information on connecting to a personal computer (PC) and running CCES.
Probing EI3 Extender Board Manual 1-3
Expansion Interface III
Figure 1-1. Assembled Board Diagram
Part DescriptionItem0.75in Nylon Standoff1
1.0in Nylon Standoff2 1.25in Nylon Standoff3
3
Nylon Screw4 Nylon Spacer5
EZ-Extender 3(Stacked)
2
2
1
1
2
4
5
4 4
4
5
Expansion Interface IIIThe Expansion Interface III (EI3) allows an extender board to be used across various hardware platforms that have the same expansion interface connectors.
The connectors contain a majority of the processor’s signals. For pinout information, go to Appendix B, “Probing EI3 Extender Board Sche-matic”. The mechanical dimensions of the expansion connectors can be obtained by contacting “Technical Support”.
1-4 Probing EI3 Extender Board Manual
Using Probing EI3 Extender Board
The Probing EI3 Extender Board can interface with EZ-KIT Lites/EZ-Boards operating at an IO voltage of 3.3V. Other IO voltages are not supported. The extender can be powered from either the EZ-KIT Lite/EZ-Board or through the on-board 5V power connector (P1).
Analog Devices offers many EZ-Extender products that plug on to the expansion interface. For more information on these products, visit the Analog Devices Web site at: www.analog.com/processors/tools/blackfin.
Limits to current and interface speed must be taken into consideration when using the EI3. Current for the EI3 can be sourced from the EZ-KIT Lite/EZ-Board; therefore, the current should be limited to 200 mA for 5V and 300 mA for the 3.3V planes. If more current is required, then a sepa-rate power connector and a regulator must be designed on the daughter card. Additional circuitry can add extra loading to signals, decreasing their maximum effective speed.
Analog Devices does not support and is not responsible for the effects of additional circuitry.
Board Design DatabaseA .zip file containing all of the electronic information required for the design, layout, fabrication and assembly of the product is available for download from the Analog Devices board design database at:http://www.analog.com/board-design-database.
Probing EI3 Extender Board Manual 1-5
Board Design Database
1-6 Probing EI3 Extender Board Manual
2 PROBING EI3 EXTENDER BOARD HARDWARE REFERENCE
This chapter describes the hardware design of the Probing EI3 Extender
Board.The following topics are covered.
• “System Architecture” on page 2-2Describes the daughter board configuration and explains how the board components interface with the processor.
• “Connectors” on page 2-3Shows the locations and provides part numbers for the on-board connectors. In addition, the manufacturer and part number infor-mation is provided for the mating parts.
• “LEDs” on page 2-5Describes the on-board LEDs.
Probing EI3 Extender Board Manual 2-1
System Architecture
System ArchitectureA block diagram of the Probing EI3 Extender Board is shown in Figure 2-1.
Figure 2-1. Probing EI3 Extender Board Block Diagram
2-2 Probing EI3 Extender Board Manual
Probing EI3 Extender Board Hardware Reference
ConnectorsThis section describes connector functionality and provides information about mating connectors. Figure 2-2 shows the locations of all connectors on the Probing EI3 Extender Board.
Figure 2-2. Connector Locations
Expansion Interface III (EI3) Connectors (J1–2)Two board-to-board connector (J1 and J2) provide signals from the PPI, SPI, TWI, UART, SPORT, and GPIO interfaces of the processor. The connectors are located on the top side of the board.
Part Description Manufacturer Part Number
120-pin, 0.6 mm HIROSE FX8-120S-SV(21)
Mating Connector
120-pin, 0.6 mm HIROSE FX8-120P-SV1(91)
Probing EI3 Extender Board Manual 2-3
Connectors
Expansion Interface III (EI3) Connectors (P1–2)Two board-to-board connector (P1 and P2) provide signals from the PPI, SPI, TWI, UART, SPORT, and GPIO interfaces of the processor. The connectors are located on the bottom side of the board and used when stacking another.
Part Description Manufacturer Part Number
120-pin, 0.6 mm HIROSE FX8-120P-SV1(91)
Mating Connector
120-pin, 0.6 mm HIROSE FX8-120S-SV(21)
Probing Connectors (P3–P6)The probing connectors (P3–P6) are 30 2 IDC connectors which are used for probing any of the signals on the Expansion Interface III connectors.
Part Description Manufacturer Part Number
HDMI FCI 10029449-002TLF
Mating Cable
HDMI cable MEDIABRIDGE 91-02X-06B
2-4 Probing EI3 Extender Board Manual
Probing EI3 Extender Board Hardware Reference
Power Connector (J3)Under normal circumstances, the power connector is not needed and is not populated on the board.
Part Description Manufacturer Part Number
2.5 mm power jack CUI PJ-036BH-SMT
Mating Cable
[email protected] power supply GLOBETEK GS-1750(R)
LEDsThis section describes the on-board LEDs.
Power LED (LED1)When LED1 is lit solid (green), it indicates that power is being supplied to the board properly.
Probing EI3 Extender Board Manual 2-5
LEDs
2-6 Probing EI3 Extender Board Manual
A PROBING EI3 EXTENDER BOARD BILL OF MATERIALS
The bill of materials corresponds to “Probing EI3 Extender Board Schematic”
on page B-1.Ref. Qty. Description Reference Designator
Manufacturer Part Number
1 1 EI3_PROBING_ADAPTER 24LC32AF U1
U1 MICROCHIP 24LC32AF-I/ST
2 2 0.6MM 120PIN HIROSE_FX8-120P-SV1(91)
P1,P2 HIROSE FX8-120P-SV1(91)
3 2 .6MM 120PIN HIROSE_FX8-120S-SV(21)
J1,J2 HIROSE FX8-120S-SV(21)
4 4 IDC 30X2 IDC30X2 P3-P6 FCI 77313-101-60LF
5 1 0.1UF 10V 10% 0402 C1 AVX 0402ZD104KAT2A
6 4 0 1/16W 5% 0402 R2,R5-R7 PANASONIC ERJ-2GE0R00X
7 1 1K 1/10W 5% 0603 R3 DIGI-KEY 311-1.0KGRTR-ND
8 1 GREEN LED001 LED1 PANASONIC LN1361CTR
9 1 200MA BAT54 SOT23D D1 MOUSER 512-BAT54
10 3 100K 1/16W 5% 0402 R1,R4,R8 DIGI-KEY 541-100KJTR-ND
Probing EI3 Extender Board Manual A-1
A-2 Probing EI3 Extender Board Manual
Title Page
1 107/27/2010
EI3 Probing Adapter
A0243-2010 0.1
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
EI3 Probing Adapter
EI3 Connectors
2 207/27/2010
EI3 Probing Adapter
A0243-2010 0.1
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
RevHIROSE_FX8-120S-SV(21)
J1
101
100
71
70
120
118
116
114
112
110
108
106
104
102
98
96
94
92
90
88
86
84
82
80
78
76
74
72
119
117
115
113
111
109
107
105
103
99
97
95
93
91
89
87
85
83
81
79
77
75
73
69
66
6867
64
61
63
65
11
62
36
35
8
6
4
2
9
7
5
3
1
12
10
59
60
55
53
51
49
47
45
43
41
39
56
54
52
50
40
48
46
44
42
58
57
3433
16
18
20
22
14
24
26
28
30
32
13
15
17
19
21
23
25
27
29
31
37 38SPI0_SEL_CSPI0_SEL_B
SPORT1_D1
SPORT0_TDV
PPI_FS1
RSVD5
GND6
RSVD2
PPI0_D3
GND5
PPI0_D9
PPI0_D13
SPORT0_D1
SPORT1_TDV
GND7
PPI0_FS3
RSVD4
PPI0_D11
RSVD3
PPI0_D1
PPI0_D5
PPI0_D7
SPI0_D2 SPI0_D3
RESET_OUT*
GND12
SCL1*
GPIO2
GND10
TMR_A
GND9
SPI0_RDY
GND11
RSVD8
TWI0_A0*
SPI0_SEL1/SPI0_SS*
SDA1*
GPIO0
GPIO4
GPIO6
TMR_C
RSVD6
RSVD7
RSVD9
RESET_IN*
UART0_RX
PPI0_D17
PPI0_D14
VIN
GND1
USB_VCC
PPI0_D23
PPI0_D19
RSVD1
GND2
GND3
PPI0_D21
SPORT_INT
GND8
UART0_TX
GND4
WAKE*
GND13
EXT_BOOT
SLEEP*
RSVD11 RSVD12
RSVD10
GND14
TMR_B
GND15
GPIO3
SCL0*
GND16
SPI0_MISO
SPI0_SEL_A
SPORT0_CLK
SPORT0_FS
SPORT1_D0
GND18
PPI0_FS2
RSVD15
PPI0_INT
PPI0_D4
PPI0_D6
PPI0_D10
GND21
PPI0_D16
PPI0_D20
GND22
GND23
RSVD17
TMR_D*
GPIO7*
GPIO5
GPIO1
SDA0*
SPI0_CLK
SPI0_MOSI
GND17
SPORT0_D0
SPORT1_FS
SPORT1_CLK
PPI0_CLK
RSVD14
GND19
PPI0_D2
GND20
PPI0_D8
PPI0_D12
PPI0_D15
PPI0_D18
PPI0_D22
VIO
GND24
PS_IN
RSVD13
CLKOUT
RSVD16
PPI0_D0
HIROSE_FX8-120S-SV(21)
J2
97
95
99
96
94
101
119
71
70
120
118
116
110
108
106
104
102
98
112
100
92
90
88
86
84
82
80
78
7674
72
117
115109
107
105
103
114
113
111
93
91
89
87
85
83
81
79
77
75
73
69
66
68
67
64
61
63
65
11
62
36
35
8
6
4
2
9
7
5
3
1
12
10
59
60
55
5351
49
47
45
43
41
39
56
54
52
50
40
48
46
44
42
58
57
3433
16
18
20
22
14
24
26
28
30
32
13
15
17
19
21
23
25
27
29
31
37
38ASYNC_A14
ASYNC_A13
ASYNC_A8
ASYNC_A6
ASYNC_A5
ASYNC_BGH
GND6
ASYNC_ARDY
ASYNC_D19
GND5
ASYNC_D25
ASYNC_D29
ASYNC_A9
ASYNC_A7
GND7
ASYNC_A4
ASYNC_BG
ASYNC_D27
ASYNC_BR
ASYNC_D17
ASYNC_D21
ASYNC_D23
ASYNC_A10 ASYNC_A11
PWM0_TRIP0
GND12
ASYNC_A17
ASYNC_A19
GND10
PWM0_AL
GND9
PWM0_BL
GND11
PWM0_DH
PWM0_SYNC
ASYNC_A15
ASYNC_A16
ASYNC_A18
ASYNC_A20
PWM0_AH
PWM0_BH
PWM0_CH PWM0_CL
PWM0_DL
RSVD2
PWM0_TRIP1
ASYNC_AMS3
ASYNC_D30
VIN
GND1
USB_VCC
ASYNC_AOE
ASYNC_AMS2
RSVD1
GND2
GND3
ASYNC_AMS0
ASYNC_A12
GND8
RSVD4
GND4
ACM0_A1
GND13
RSVD3
ACM0_A0
ACM0_A3
ACM0_A4
ACM0_A2
GND14
ACM0_CLK
GND15
RSVD7
RSVD9
GND16
RSVD12
RSVD14
RSVD15
RSVD17
RSVD19
GND18
RSVD22
RSVD24
RSVD25
ASYNC_D120
ASYNC_D22
ASYNC_D26
GND21 GND22
GND23
ACM0_T1
RSVD5 RSVD6
RSVD8
RSVD10
RSVD11
RSVD13
GND17
RSVD16
RSVD18
RSVD20
RSVD21
RSVD23
GND19
ASYNC_D18
GND20
ASYNC_D24
ASYNC_D28
ASYNC_D31
VIO
GND24
PS_IN
ACM0_FS
ACM0_T0
RSVD26
ASYNC_D16
ASYNC_A21
ASYNC_A23
ASYNC_A25
ASYNC_A22
ASYNC_A24
HIROSE_FX8-120P-SV1(91)
P1
101
100
71
70
120
118
116
114
112
110
108
106
104
102
98
96
94
92
90
88
86
84
82
80
78
76
74
72
119
117
115
113
111
109
107
105
103
99
97
95
93
91
89
87
85
83
81
79
77
75
73
69
66
6867
64
61
63
65
11
62
36
35
8
6
4
2
9
7
5
3
1
12
10
59
60
55
53
51
49
47
45
43
41
39
56
54
52
50
40
48
46
44
42
58
57
3433
16
18
20
22
14
24
26
28
30
32
13
15
17
19
21
23
25
27
29
31
37 38SPI0_SEL_CSPI0_SEL_B
SPORT1_D1
SPORT0_TDV
PPI_FS1
RSVD5
GND6
RSVD2
PPI0_D3
GND5
PPI0_D9
PPI0_D13
SPORT0_D1
SPORT1_TDV
GND7
PPI0_FS3
RSVD4
PPI0_D11
RSVD3
PPI0_D1
PPI0_D5
PPI0_D7
SPI0_D2 SPI0_D3
RESET_OUT*
GND12
SCL1*
GPIO2
GND10
TMR_A
GND9
SPI0_RDY
GND11
RSVD8
TWI0_A0*
SPI0_SEL1/SPI0_SS*
SDA1*
GPIO0
GPIO4
GPIO6
TMR_C
RSVD6
RSVD7
RSVD9
RESET_IN*
UART0_RX
PPI0_D17
PPI0_D14
VIN
GND1
USB_VCC
PPI0_D23
PPI0_D19
RSVD1
GND2
GND3
PPI0_D21
SPORT_INT
GND8
UART0_TX
GND4
WAKE*
GND13
EXT_BOOT
SLEEP*
RSVD11 RSVD12
RSVD10
GND14
TMR_B
GND15
GPIO3
SCL0*
GND16
SPI0_MISO
SPI0_SEL_A
SPORT0_CLK
SPORT0_FS
SPORT1_D0
GND18
PPI0_FS2
RSVD15
PPI0_INT
PPI0_D4
PPI0_D6
PPI0_D10
GND21
PPI0_D16
PPI0_D20
GND22
GND23
RSVD17
TMR_D*
GPIO7*
GPIO5
GPIO1
SDA0*
SPI0_CLK
SPI0_MOSI
GND17
SPORT0_D0
SPORT1_FS
SPORT1_CLK
PPI0_CLK
RSVD14
GND19
PPI0_D2
GND20
PPI0_D8
PPI0_D12
PPI0_D15
PPI0_D18
PPI0_D22
VIO
GND24
PS_IN
RSVD13
CLKOUT
RSVD16
PPI0_D0
P2
HIROSE_FX8-120P-SV1(91)
97
95
99
96
94
101
119
71
70
120
118
116
110
108
106
104
102
98
112
100
92
90
88
86
84
82
80
78
7674
72
117
115109
107
105
103
114
113
111
93
91
89
87
85
83
81
79
77
75
73
69
66
68
67
64
61
63
65
11
62
36
35
8
6
4
2
9
7
5
3
1
12
10
59
60
55
5351
49
47
45
43
41
39
56
54
52
50
40
48
46
44
42
58
57
3433
16
18
20
22
14
24
26
28
30
32
13
15
17
19
21
23
25
27
29
31
37
38ASYNC_A14
ASYNC_A13
ASYNC_A8
ASYNC_A6
ASYNC_A5
ASYNC_BGH
GND6
ASYNC_ARDY
ASYNC_D19
GND5
ASYNC_D25
ASYNC_D29
ASYNC_A9
ASYNC_A7
GND7
ASYNC_A4
ASYNC_BG
ASYNC_D27
ASYNC_BR
ASYNC_D17
ASYNC_D21
ASYNC_D23
ASYNC_A10 ASYNC_A11
PWM0_TRIP0
GND12
ASYNC_A17
ASYNC_A19
GND10
PWM0_AL
GND9
PWM0_BL
GND11
PWM0_DH
PWM0_SYNC
ASYNC_A15
ASYNC_A16
ASYNC_A18
ASYNC_A20
PWM0_AH
PWM0_BH
PWM0_CH PWM0_CL
PWM0_DL
RSVD2
PWM0_TRIP1
ASYNC_AMS3
ASYNC_D30
VIN
GND1
USB_VCC
ASYNC_AOE
ASYNC_AMS2
RSVD1
GND2
GND3
ASYNC_AMS0
ASYNC_A12
GND8
RSVD4
GND4
ACM0_A1
GND13
RSVD3
ACM0_A0
ACM0_A3
ACM0_A4
ACM0_A2
GND14
ACM0_CLK
GND15
RSVD7
RSVD9
GND16
RSVD12
RSVD14
RSVD15
RSVD17
RSVD19
GND18
RSVD22
RSVD24
RSVD25
ASYNC_D20
ASYNC_D22
ASYNC_D26
GND21 GND22
GND23
ACM0_T1
RSVD5 RSVD6
RSVD8
RSVD10
RSVD11
RSVD13
GND17
RSVD16
RSVD18
RSVD20
RSVD21
RSVD23
GND19
ASYNC_D18
GND20
ASYNC_D24
ASYNC_D28
ASYNC_D31
VIO
GND24
PS_IN
ACM0_FS
ACM0_T0
RSVD26
ASYNC_D16
ASYNC_A21
ASYNC_A23
ASYNC_A25
ASYNC_A22
ASYNC_A24
J1-94
J1-94
J1-27
J1-27 J1-95
J1-95 J1-101
J1-101 J1-102
J1-102 J1-103
J1-103 J1-105
J1-105 J1-106
J1-106 J1-107
J1-107 J1-108
J1-108 J1-12
J1-12 J1-111
J1-111 J1-112
J1-112 J1-113
J1-113 J1-114
J1-114 J1-99
J1-99
J1-26
J1-26 J1-20
J1-20 J1-19
J1-19 J1-18
J1-18 J1-16
J1-16 J1-15
J1-15 J1-14
J1-14 J1-13
J1-13 J1-110
J1-110 J1-10
J1-10 J1-9
J1-9 J1-8
J1-8 J1-7
J1-7
J1-92
J1-92 J1-90
J1-90 J1-30
J1-30 J1-91
J1-91 J1-31
J1-31
J1-87
J1-87 J1-89
J1-89 J1-29
J1-29 J1-88
J1-88 J1-32
J1-32 J1-35
J1-35
J1-82
J1-82 J1-83
J1-83 J1-33
J1-33 J1-39
J1-39 J1-37
J1-37 J1-61
J1-61
J1-50
J1-50 J1-84
J1-84 J1-34
J1-34 J1-85
J1-85 J1-38
J1-38
J1-43
J1-43 J1-44
J1-44 J1-45
J1-45 J1-47
J1-47
J1-48
J1-48 J1-49
J1-49
J1-59
J1-59
J1-42
J1-42 J1-41
J1-41
J1-78
J1-78 J1-77
J1-77 J1-76
J1-76 J1-74
J1-74
J1-73
J1-73 J1-72
J1-72
J1-62
J1-62
J1-64
J1-64
J1-57
J1-57
J1-65
J1-65
J1-60
J1-60
J1-71
J1-71
GND
VIN
VIN
VIN
VIN
PS_IN
PS_IN
PS_IN
PS_IN
VIO
VIO
VIO
VIO
USB_VCC
USB_VCC
USB_VCC
USB_VCC
J1-2
J1-2 J1-22
J1-22 J1-25
J1-25 J1-53
J1-53 J1-55
J1-55 J1-67
J1-67 J1-70
J1-70 J1-97
J1-97 J1-119
J1-119
J1-21
J1-21 J1-24
J1-24 J1-51
J1-51 J1-54
J1-54 J1-66
J1-66 J1-68
J1-68 J1-96
J1-96 J1-100
J1-100
J2-8
J2-8 J2-10
J2-10 J2-21
J2-21 J2-22
J2-22
J2-43
J2-43 J2-45
J2-45
J2-101
J2-101 J2-102
J2-102
J2-107
J2-107
J2-68
J2-68 J2-72
J2-72
J2-26
J2-26 J2-29
J2-29 J2-31
J2-31 J2-33
J2-33 J2-35
J2-35 J2-38
J2-38 J2-41
J2-41
J2-103
J2-103 J2-105
J2-105 J2-106
J2-106
J2-9
J2-9 J2-7
J2-7 J2-25
J2-25 J2-24
J2-24 J2-27
J2-27 J2-30
J2-30 J2-32
J2-32 J2-34
J2-34 J2-37
J2-37 J2-39
J2-39 J2-42
J2-42 J2-44
J2-44
J2-20
J2-20 J2-19
J2-19 J2-18
J2-18 J2-16
J2-16 J2-15
J2-15 J2-14
J2-14 J2-108
J2-108 J2-110
J2-110
J2-13
J2-13 J2-12
J2-12
J2-47
J2-47 J2-49
J2-49 J2-51
J2-51 J2-54
J2-54 J2-57
J2-57 J2-56
J2-56
J2-48
J2-48 J2-50
J2-50 J2-53
J2-53 J2-55
J2-55 J2-59
J2-59
J2-73
J2-73 J2-64
J2-64 J2-66
J2-66
J2-70
J2-70 J2-65
J2-65 J2-67
J2-67 J2-71
J2-71
J2-2
J2-2 J2-61
J2-61 J2-74
J2-74 J2-77
J2-77 J2-79
J2-79 J2-82
J2-82 J2-84
J2-84 J2-87
J2-87 J2-89
J2-89 J2-91
J2-91
J2-94
J2-94 J2-96
J2-96 J2-99
J2-99
J2-111
J2-111 J2-113
J2-113 J2-119
J2-119
J2-60
J2-60 J2-62
J2-62 J2-76
J2-76 J2-78
J2-78 J2-80
J2-80 J2-83
J2-83 J2-85
J2-85 J2-88
J2-88 J2-90
J2-90 J2-92
J2-92
J2-95
J2-95 J2-97
J2-97
J2-100
J2-100 J2-112
J2-112 J2-114
J2-114
TWI0_A0
TWI0_A0 SCL0
SCL0 SDA0
SDA0
IDC30X2
P3
60 59
58 57
56 55
54 53
52 51
50
48
46
44
42
40
38
49
47
45
43
41
39
37
36 35
3334
32 31
30
28
29
27
26
24
22
20
18
16
25
23
21
19
17
15
11
13
9
1
3
5
7
4
2
6
10
8
12
14
IDC30X2
P4
60 59
58 57
56 55
54 53
52 51
50
48
46
44
42
40
38
49
47
45
43
41
39
37
36 35
3334
32 31
30
28
29
27
26
24
22
20
18
16
25
23
21
19
17
15
11
13
9
1
3
5
7
4
2
6
10
8
12
14
IDC30X2
P5
60 59
58 57
56 55
54 53
52 51
50
48
46
44
42
40
38
49
47
45
43
41
39
37
36 35
3334
32 31
30
28
29
27
26
24
22
20
18
16
25
23
21
19
17
15
11
13
9
3
5
7
4
6
10
8
12
14
2 1
IDC30X2
P6
60 59
58 57
56 55
54 53
52 51
50
48
46
44
42
40
38
49
47
45
43
41
39
37
36 35
3334
32 31
30
28
29
27
26
24
22
20
18
16
25
23
21
19
17
15
11
13
9
1
3
5
7
4
2
6
10
8
12
14
Probing Connectors
3 307/27/2010
EI3 Probing Adapter
A0243-2010 0.1
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
J1-94 J1-27
J1-95
J1-101
J1-102
J1-103
J1-105
J1-106
J1-107
J1-108
J1-12
J1-111
J1-112
J1-113
J1-114
J1-99
J1-26
J1-20
J1-19
J1-18
J1-16
J1-15
J1-14
J1-13
J1-110
J1-10
J1-9
J1-8
J1-7
J1-92
J1-90
J1-30J1-91
J1-31
J1-87
J1-89
J1-29
J1-88
J1-32
J1-35
J1-82
J1-83
J1-33
J1-39
J1-37
J1-61
J1-50
J1-84
J1-34
J1-85
J1-38
J1-43
J1-44
J1-45
J1-47
J1-48
J1-49
J1-59
J1-42
J1-41
J1-78
J1-77
J1-76
J1-74
J1-73
J1-72
J1-62
J1-64 J1-57
J1-65
J1-60
J1-71
VINVIN PS_INPS_IN
VIO VIO USB_VCCUSB_VCC
J1-2
J1-22
J1-25
J1-53
J1-55
J1-67
J1-70
J1-97
J1-119
J1-21
J1-24
J1-51
J1-54
J1-66
J1-68
J1-96
J1-100
J2-8
J2-10
J2-21
J2-22
J2-43
J2-45
J2-101
J2-102
J2-107
J2-68
J2-72
J2-26
J2-29
J2-31
J2-33
J2-35
J2-38
J2-41
J2-103
J2-105
J2-106
J2-9
J2-7
J2-25
J2-24
J2-27
J2-30
J2-32
J2-34
J2-37
J2-39
J2-42
J2-44
J2-20
J2-19
J2-18
J2-16
J2-15
J2-14
J2-108
J2-110
J2-13
J2-12
J2-47
J2-49
J2-51
J2-54
J2-57
J2-56
J2-48
J2-50
J2-53
J2-55
J2-59
J2-73
J2-64
J2-66
J2-70
J2-65
J2-67
J2-71
J2-2
J2-61
J2-74
J2-77
J2-79
J2-82
J2-84
J2-87
J2-89
J2-91
J2-94
J2-96
J2-99
J2-111
J2-113
J2-119
J2-60
J2-62
J2-76
J2-78
J2-80
J2-83
J2-85
J2-88
J2-90
J2-92
J2-95
J2-97
J2-100
J2-112
J2-114
TWI0_A0
SCL0
SDA0
Flash and Power
4 407/27/2010
EI3 Probing Adapter
A0243-2010 0.1
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
24LC32AFTSSOP8DW
U1
47
5
6
3
2
1
8VCC
A0
A1
A2
SCL
SDA
WPGND
R4100K0402
R700402
R600402
C10.1UF0402
R500402
DNP0402100KR8
DNP
R1100K0402
04020R2
DNP
J3
CON068
3
2
1
R31K0603
LED1GREENLED001
D1
200MABAT54
SOT23D
VIN
VIO
VIO
TWI0_A0
SCL0
SDA0
I INDEX
A E
architecture, of Probing EI3 Extender Board,2-2assembled board diagram, 1-4
Bbill of materials, A-1block diagram
assembled board, 1-4Probing EI3 Extender Board, 2-2
board design, 1-5board schematic (Probing EI3 Extender Board),
B-1
Cconnectors, 2-3
diagram of locations, 2-3IDC, 2-4J1-2 (EI3), 2-3J3 (power), 2-5P1-2 (EI3), 2-4P1 (power), 1-5P3-P6 (probing), 2-4
contents, of this Extender Board package, 1-2
EngineerZone, xiiexpansion interface III (EI3)
connectors (J1-2), 2-3connectors (P1-2), 2-4overview, 1-4
extender board block diagram, 2-2
IIDC connectors, 2-4installation, of this Extender Board, 1-3
LLEDs, 2-5
LED1 (power), 2-5
Ooperating systems, supported, 1-2
Ppackage contents, 1-2power
connector (J3), 2-5connector (P1), 1-5LED (LED1), 2-5
probing connector), 2-4product overview, vii
Probing EI3 Extender Board Manual I-1
Index
Rrelated documents, xiii
Sschematic, of Probing EI3 Extender Board,
B-1supported operating systems, 1-2supported products, xisystem architecture, 2-2system requirements, 1-3
Ttechnical support, x
I-2 Probing EI3 Extender Board Manual