presented by dipjyoti acharya m.s.m.e thesis defense may 30, 2006, 11: 00
DESCRIPTION
Design and Performance Evaluation of a Miniature Integrated Single Stage Centrifugal Compressor and Permanent Magnet Synchronous Motor. Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00 Dept. of Mechanical, Materials and Aerospace Engineering - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/1.jpg)
Design and Performance Evaluation of a Miniature Integrated Single Stage Centrifugal Compressor and
Permanent Magnet Synchronous Motor
Presented by
Dipjyoti Acharya
M.S.M.E Thesis DefenseMay 30, 2006, 11: 00
Dept. of Mechanical, Materials and Aerospace Engineering
University of Central Florida, Orlando
![Page 2: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/2.jpg)
Project Requirements
Reverse Turbo Brayton Cycle Cryocooler
Single Stage Centrifugal Compressor Permanent Magnet Synchronous Motor
Specifications Specifications
Working fluid Air
Stages 1
Compression ratio (total to total)
1.58
Inlet condition 1 atm, 300K
Impeller rev. speed 108,000 RPM
Mass flow rate 7.3 g/s
Efficiency 0.65
Output Power 2000 W
Operational Speed 200,000 rpm
Efficiency @ 77 K 89.9 %
Rotor Titanium
Stator Slot less Laminated
Magnet Samarium Cobalt
Wire Multi-strand Litz Wire
Winding 6 turns/phase/pole
![Page 3: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/3.jpg)
Single Stage Centrifugal Compressor
![Page 4: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/4.jpg)
Components of the Centrifugal Compressor
Impeller
DiffuserInlet Guide Vane
Top plateCollectorKoford Electric MotorController
Coupler
Courtesy : Ray Zhou, Kevin Finney
![Page 5: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/5.jpg)
Compressor Experimental Setup
P1, T1
P2, T2
P3, T3
P4, T4
![Page 6: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/6.jpg)
Experimental Initial Results
Power versus Speed
0.0
200.0
400.0
600.0
800.0
1000.0
1200.0
1400.0
0 20000 40000 60000 80000 100000 120000
Speed (rpm)
Po
wer
(W
atts
)
Cast Impeller
StraightBladeImpeller Test1
StraightBladeImpeller Test2
StraightBladeImpeller w/DataAcquisition
![Page 7: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/7.jpg)
Issues to be resolved
• Resolve misalignment issues• Design of new coupler to handle high speeds• Design a new electric motor to handle the power required
by compressor
![Page 8: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/8.jpg)
Problems with Rimitec Coupler
• Servo-insert coupling allowed a restricted amount of misalignment
• Elastic material in the middle began to plastically deform
• Stainless steel retaining ring was slip fit
• Coupler more rigid and prevented it from handling any misalignment
Disc couplings style –WM Berg Coupler
![Page 9: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/9.jpg)
Coupler Selection Guide
Coupler Type Backlash Allowed
Torque Transmittal
Mis-alignment allowed Speed Capability
Overall rating
Axial Angular Parallel Torsional
Importance Rating
Scale 2 3 4 5 6 1 7
Rigid None Large None None None None Large 30
Flexible Jaw Medium Medium Small Small Small None Small 32
Servo-insert/ Disc
None Medium Medium Medium Medium Small Medium 51
Gear and Spline
Small Large Medium Medium Medium Small Small 38
Helical and bellows
Small Large Medium Small Small Small Small 49
Universal joint
Medium Medium Small Large None Small Small 37
![Page 10: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/10.jpg)
Design of the Helical Coupler
1) Why use a flexible shaft coupling ?
2) Helical Flexure
3) Multiple Starts
4) Flexure Creation Process
5) Material Martensitic stainless steel CC455 H900 per AMS 5617
Wire EDM, Dynamically balanced while in production
Best for high speed application
Double Start, Ansys Analysis Heli-cal Inc.
Rigid couplings would have been always used if it were possible to perfectly align these shafts
![Page 11: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/11.jpg)
Helical Coupler
Courtesy:
Heli-cal Products
Company Inc.
![Page 12: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/12.jpg)
Alignment Issues and translational stages
1) Straight Edge
2) Laser Alignment Systems - Laser systems
3) Dial indicator methods are
A) RIM FACE METHODB) REVERSE RIM METHOD
![Page 13: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/13.jpg)
Reverse Rim Alignment Method
SCHEMATIC DIAGRAM OF COMPRESSOR – MOTOR SYSTEM FOR REVERSE RIM ALIGNMENT METHOD
M = the offset in the plane of the movable indicator. S = the offset in the plane of the stationary indicator. A = the distance between the stationary and movable dial indicator plungers. B = the distance from the movable dial indicator plunger to the movable machine’s front feet bolt center. C= the distance between the movable machines’ front and rear feet bolt centers.
![Page 14: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/14.jpg)
Verification of Components With FARO ARM
![Page 15: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/15.jpg)
Experimental Results – Translational Stages
![Page 16: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/16.jpg)
Experiment Helical Coupler –Fixed Base
![Page 17: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/17.jpg)
Compressor Characteristics Curve
![Page 18: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/18.jpg)
Available Drivers for Centrifugal Compressor
Required speed 108,000 rpm. Achieved Speed 90,000 rpm
Electric Motor
Air-Turbine Turbocharger
Speeds 158,000 rpm 250,000 rpm 200,000 rpm
Accessories Controller TC-Control SystemMist Lubricator
Speed Controlling Unit
Coupling Flexible Coupler
Spline Shaft Spline Shaft
Cost $ 2500 $ 30,000 $35,000
![Page 19: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/19.jpg)
Design of Permanent Magnet Synchronous Motor
![Page 20: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/20.jpg)
Material Selection for Shaft
![Page 21: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/21.jpg)
Shear Stress Analysis
Maximum Shear Stress Theory
Power being transmitted = P = 2000 WSpeed of rotation of the shaft = N = 200000 rpmAngular velocity of rotation = ω = 2* π *N/60Torque developed = T = P/ ω = 0.095 N.mMaximum allowable shear stress = τ maxFactor of Safety = F = 3a = ASME factor for shaft design for shear = ¾No vertical shear stressRigidity modulus of the shaft m/l = γ = 117 GPaAngle of shaft twist because of torsion = α (maximum for the outer layer)
For a τmax value of 20305 psi (for a Titanium), d = 15.846 mmThickness of the hollow shaft = t = [D – d]/2 = 0.077 mm << 0.5 mm
So, the shaft would not fail under pure shear.Also, Angle of Twist
4
1
max
4
*
]**32**[
DTFaD
d
*
1**584
4DTorque 410*847.1
![Page 22: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/22.jpg)
Bending Stress
The values considered for the bending stress are as follows,Elastic modulus of shaft = 116,000 MPaPoisson’s ratio for shaft = υ = 0.34Ultimate tensile strength of the shaft = 220 MPaElastic modulus of permanent magnet = 150,000 MPa Poisson’s ratio for permanent magnet(ν) = 0.3Ultimate tensile strength of the permanent magnet = 82.7 MPaBending moment due to impeller weight = M = 3.74 N-mmShaft cross-section – Hollow ShaftPermanent magnet cross-section – Solid ShaftDensity of the shaft m/l (ρshaft) = 4500 kg/m3Density of the permanent magnet (ρmagnet) = 7500 kg/m3Maximum bending stress (σmax) = M/Z, where Z = section modulus.
σmax ,Titanium = 0.037 MPa << Ultimate tensile strength of shaft.σmax, Permanent Magnet = 0.048 MPa << Ultimate tensile strength of permanent magnet.So the shaft would not fail under pure bending.
![Page 23: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/23.jpg)
Fracture Toughness
Fracture Toughness is an issue at cryogenic temperatures. It is defined k = cs(√ π*c)α, where ‘k’ is the ‘Critical Stress Intensity’,Cs – Critical Stress,c – crack length,α – geometry factor (depends on the cross-section of the member)‘k’ depends on the Bending Stress developed.
![Page 24: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/24.jpg)
Centrifugal Stress Analysis
•Centrifugal stress developed in shaft at 200K rpm = 728 MPa.
•Centrifugal stress developed in magnet at 200K rpm = 261.2 MPa
![Page 25: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/25.jpg)
Thermal Analysis
•Thermal stress developed in the shaft at 77 K = 329 MPa
•Thermal stress developed in the magnet at 77 K = 130 MPa
Stress due to centrifugal force in shaft rotating at 200,000 rpm = 728 MPaStress due to centrifugal force in magnet rotating at 200,000 rpm = 251.2 MPaThermal stress developed in shaft due to operating at 77 K = 329 MPaThe Total Stress = 1308.2 MPa < Titanium Grade Yield Strength 1420 MPa
So the titanium shaft would not fail.
Also, Thermal Stress developed in magnet = 130 MPa < Compressive Strength = 833 MPa.
So, the magnet would not crack or crumble to powder.
![Page 26: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/26.jpg)
Rotordynamic Analysis of Rotor
Courtesy: Dr. Nagraj Arakere , UF, Gainsville
![Page 27: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/27.jpg)
Assembly of the Rotor
![Page 28: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/28.jpg)
Fabrication of PMSM
![Page 29: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/29.jpg)
Results PMSM
![Page 30: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/30.jpg)
Motor-Generator Set
![Page 31: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/31.jpg)
Design of the Integrated Compressor –Motor System
• Elimination of the coupler
• Reduction of number of bearings in the system
• Usage of fewer components on the rotor to increase the stiffness
![Page 32: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/32.jpg)
Rotordynamic Analysis of Integrated System
![Page 33: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/33.jpg)
![Page 34: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/34.jpg)
Fabrication of Integrated Rotor
![Page 35: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/35.jpg)
Test Rig Structure
![Page 36: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/36.jpg)
Features
![Page 37: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/37.jpg)
Test Accessories – Electrical
Code ComposerEmulator, DSP and Motor ControllerLow Pass FilterPower Meter
Courtesy: Liping Zheng and Limei Zhou
![Page 38: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/38.jpg)
Test Accessories – Flow
P-Transducers
Mass Flow Meter
![Page 39: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/39.jpg)
Bearing mounting, fit and pre-load
deltaRCFs 100000 2
1800s2
Es
1 R
2
3
3 R0
2
R
2
deltaRS 50R K s
Roarke’s Handbook of Stress and StrainCourtesy : Krishna
![Page 40: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/40.jpg)
Alignment of Bearings
![Page 41: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/41.jpg)
Integrated Compressor – Motor Test Set-up
Motor Jacket Stator inside
Gas enclosure with adjustable IGV to control tip clearance
![Page 42: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/42.jpg)
Two Piece Rotor
• Free spin test results were successful
only to 42,000 rpm • Wobbling near the aluminum impeller
plug by 0.008 inches • Hair crack was visible at the joint
Externally
Threaded Shaft
Internally Threaded
Impeller
Fabricated Two Piece Rotor
![Page 43: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/43.jpg)
Compressor Performance Chart
![Page 44: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/44.jpg)
![Page 45: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/45.jpg)
Problems and Future Work in Test Setup
• Vibrations experienced around 34000 – 37000 rpm range.
- leading to stoppage
• Bearings cooling method to be determined.
![Page 46: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/46.jpg)
Conclusion
Initial Compressor-Motor Test Setup developed and tested- Helical Coupler was designed and tested- Alignment method was improved by Reverse Rim Method and Translational
Stages- Components were verified with FARO Arm and re-fabricated
2 KW Permanent Magnet Synchronous Motor designed and tested- Shaft Material Selection, Stress Analysis Performed and Optimized by
Rotordynamic Analysis. Bearing Selection- Fabrication, Assembly Performed and Tested- Motor-Generator set developed to determine motor performance
Integrated Compressor – Motor Structure Designed and Tested
- Versions of Integrated Rotor was designed and tested- Bearing Fit determined, Pre-load structure designed- Innovative procedure for alignment developed- Adjustable IGV developed for control over tip clearance
![Page 47: Presented by Dipjyoti Acharya M.S.M.E Thesis Defense May 30, 2006, 11: 00](https://reader035.vdocuments.site/reader035/viewer/2022062217/56814e5e550346895dbbfc3b/html5/thumbnails/47.jpg)
Thank you