preface place of electrical circuits in modern technology introduction the design of the circuits...
TRANSCRIPT
Preface
• Place of Electrical Circuits in Modern Technology
Introduction
The design of the circuits has 2 main objectives:
1) To gather, store, process, transport, and present information.
2) To distribute and convert energy between various forms.
The study of circuits provides a foundation for areas of electrical engineering such as:
• Communication system
•Computer system
•Control system
•Electronics
•Electromagnetic
•Power systems
•Signal processing
•Motivation for doing this course
•About the course
Circuit Theory
Circuit Analysis
Circuit Synthesis
Circuits(given)
Excitation(given)
Response(unknown)
Circuit Analysis
What we emphasize on,Since it provides the foundation for understanding the interaction of signal solution.
Circuits(unknown)
Excitation(given)
Response(given)
Circuit synthesis (design)
In contrast to analysis,a design problem may have no solution or several solutions,
Resistance circuits analysis
Dynamic circuits analysis
Sinusoidal steady state
The course includes 3 parts:
•Reference Books
1)Fundamentals of Electric Circuits Charles K Alexander, Matthew N O Sadiku 清华大学出版社
2)The Analysis and Design of Linear Circuits Roland E.Thomas, Albert J.Rosa—2nd ed
3) Electrical Engineering Principles and Applications Allan R.Hambley ---2nd ed
4) 电路分析基础 李瀚荪 第三版
5) 电路 邱关源 第四版
6) Electric Circuits Joseph Edminister, Mahmood Nahvi -----3rd ed
Chapter 1
Fundamental Knowledge
Circuit and circuit model
• Actual electrical component: a battery or a light bulb
Actual electrical component
Ideal circuit component
Emphasize the main character
Neglect the left character
• Ideal circuit component: a mathematical model of an actual electric component.
R1
Vs
Rs
Circuit model: A commonly used mathematical model for electric system.
Lumped elements Lumped circuit
i2
-V+
i1
i1=i2
V is certain
Actual scale of the circuit is much smaller than the wavelength relating to the running frequency of the circuit.
Circuit Type:
• Linear----Nonlinear
• Time invariant----Time variant
• Passive----Active
• Lumped----Distributive
Circuit Variables
dt
dqi
Electric current is the time rate of change of charge, measured in amperes (A).
A direct current (DC) is a current that remains constant with time. (I)
An alternating current (AC) is a current that varies sinusoidally with time.
Sort
Reference direction
i i >0 means the real direction is same to the reference direction
i <0 means the real direction is opposite to the reference direction
Circuit VariablesVoltage (or potential difference) is the energy required to move a unit charge through an element, measured in volts(V).
dq
dwv
Reference direction or voltage polarity
-V+
V>0 means the real polarity is same to the reference polarity
V<0 means the real polarity is opposite to the reference polarity
passive sign convention
-V+
i Passive sign convention is satisfied when current enters through the positive polarity of the voltage.
Unless otherwise stated, we will follow the passive sign convention throughout this course.
Circuit Variables Power is the time rate of expending or absorbing energy.
Measured in watts(W)
dt
dwp
vidt
dqv
dt
dwp
vdqdw
P=VI in a DC circuit
using passive sign convention
Power absorbed = - Power supplied
Reference polarities for power using passive sign convention
P > 0 absorbing power
P < 0 releasing or supplying power
Examples
Law of conservation of energy must be obeyed in any electric circuit.
0p Power absorbed = - Power supplied
Energy is the capacity to do work, measured in joules(J)
t
t
t
tvidtpdtw
0 0
The energy absorbed or supplied by an element from time t0 to time t is
Circuit Elements
Passive elements: resistors, capacitors, and inductors
Active elements: source, operational amplifiers
Voltage and Current Sources
The most important active elements are voltage or current sources that generally deliver power to the circuit connected to them. There are two kinds of sources: independent and dependent sources.
An ideal independent source is an active element that provides a specified voltage or current that is completely independent of other circuit variables.
Symbols for independent voltage source Symbols for independent voltage source
Note:
2 or more voltage sources with different value are not permissible to be connected in parallel
2 or more current sources with different value are not permissible to be connected in series
Voltage sources connected in series is equivalent to one voltage source
Current sources connected in parallel is equivalent to one current source
A voltage source connected to any branch in parallel is equivalent to itself
A current source connected to any branch in series is equivalent
to itself
An ideal dependent (or controlled) source is an active element in which the source quantity is controlled by another voltage or current.
Symbols for a) dependent voltage sources b) dependent current sources There are a total of four
variations, namely:
1. A voltage –controlled voltage source (VCVS)
2. A current –controlled voltage source (CCVS)
3. A voltage –controlled current source (VCCS)
4. A current –controlled current source (CCCS)
V1 V1
VCVS
V1 V1g
VCCS
I1
I1
CCCS
I1
V1I1
CCVS
What is the difference between independent and dependent sources?
Resistors
The circuit element used to model the current –resisting behavior of a material is the resistor.
Resistance is the capacity of materials to impede the flow of current.
The resistance R of an element denotes its ability to resist the flow of electric current; it is measured in ohms (Ω)
Symbol: R1
1k
i
u
i
u
t1t2
u
i
i
u
i
u
t1t2
u
i
Linear Time Invariant Linear Time variant
Nonlinear Time Invariant Nonlinear Time Variant
Open Circuit
Short Circuit
Linear Resistor: The resistance of the idea resistor is constant and its value does not vary over time.
The relation between voltage and current.(VAR)
v
iV=Ri (passive sign convention)
-------Ohm’s Law
Since the value of R can range from zero to infinity, it is important that we consider the two extreme possible value of R:
R=0-------is called a short circuit; V=0;
R=∞------is called an open circuit, I=0;
Conductance G is the reciprocal of the resistance, measured in siemens (s)
Power : P=vi (passive sign convention) always absorbs power from the circuit
Other methods of expressing :
G
iGvvip
R
vRivip
22
22
RG
1
About nonlinear resistor