pp kee anchor web version
TRANSCRIPT
Range
Weightanka
Wireanka
Accessanka
1
2
Class E
Deadweight
Anchor Device
to EN 795:1996
ISO 14567
Class E Deadweight
Anchor System
and Class ‘C’
Horizontal Lifeline
system
to EN 795:1996
Class B & E
Portable
Deadweight
Anchor system for
Rope Access
to EN 795:1996
Features
For roofs up to 5 degrees pitch
Suitable for wet or dry roof surface
Easy and quick assembly
Galvanised to BS EN ISO 1461
3
4
Base weights
Base weights fully encased in rubber
Rubber moulding means base weights aren’t prone to peeling
Unique design adds to performance
Reduces thermal bridging
5
Galvanised Counter weights
Each counterweight weighs 25kg and incorporate carrying handles
Different roof types require different Counterweight quantities
6
Placement
Ensure outside of Kee Anchor product is at least
2.5m from any roof edge, open void or fall hazard.
Do not position in areas where there is a risk of
contamination or accumulation of water, oil, grease
or algae
On Gravel covered roofs, brush gravel to allow
anchor bases direct contact with roof material
7
Placement
Suitable Roof TypesSuitable Roof TypesSuitable Roof TypesSuitable Roof Types---- Up to 5º Pitch
Concrete
Asphalt Mineral Felt
Stone
chippings
Single ply
membrane
(Smooth)
Steel cladding
8
Limitations
Use with suitable PPE
Ensure roof structure is suitable,
any doubts Kee Safety
recommends seeking the advice
of a structural engineer
9
Fall Restraint
Combination of anchor
position and PPE
supplied ensures no
user is able to reach a
position of 0.5m of any
roof edge, roof open or
other fall hazard
10
Cleaning/Storage
The assemblies should be kept clean, using detergent if necessary, by wiping or hosing down with clean water and dried.
Storage should be in a dry, chemically inert environment, away from sources of damage and
Store in such a way that dismantled products will not become lost or misplaced.
Where the Weightanka has been left
in position an optional cover is available.
11
Before installation
It is strongly recommended that installers
assemble and disassemble one in a place of
safety, away from the worksite to familiarise
themselves with the product
12
Class E Deadweight
Anchor Device to
EN 795:1996
ISO 14567
CE Certified to PPE
Directive
13
14
Portable, Non Penetrative, Temporary or permanent
solution
Ideal for Where Roof build up is unknown
No Roof Alterations required
Good for refurbishment projects
Quick to assemble
No part of the Weightanka weighs more than 25kg
15
Number Of Users
Fall ArrestFall ArrestFall ArrestFall Arrest---- Single User
RestraintRestraintRestraintRestraint---- Two Users
Tell Kee Safety at time of purchasing
Supplied with 2nd Eyebolt & Restraint PPE disc.
16
Number of weights
250kg (Six Galvanised weights) assembly for:
Asphalt/Mastic
Mineral Felt
Concrete
(Brushed) Stone chippings on Bitumen
300kg (Eight Galvanised weights) assembly for:
Single ply membrane (Smooth)
Steel cladding
(Brushed) Stone chippings on Asphalt/Mastic.
17
Stack weights
opposite each
other vertically
18
Assembly
TOOLS REQUIRED FOR
ASSEMBLY:
12mm A/F Hex
Allen key
19
Class ‘E’
Deadweight Anchor System
and Class ‘C’ Horizontal
Flexible Lifeline
to EN 795:1996 and
BS 7883
CE Certified to PPE
Directive
20
21
Non penetrative EN795 ‘Class C’ Wire cable
system
Allows users to be continuously attached
Up to 15 m spans
For temporary or permanent installation
No need to water proof
System incorporates corners
Fall arrest or restraint
22
Non penetrative EN795 ‘Class C’ Wire cable
system
Allows users to be continuously attached
Up to 15 m spans
For temporary or permanent installation
No need to water proof
System incorporates corners
Fall arrest or restraint
23
Layout options
SINGLE EXTREMITY ANCHORS
Fall Arrest for a single user
-Or alternatively-
Fall Restraint for up to 3 users
(maximum 2 users in a single span)
24
Layout options
DOUBLE EXTREMITY/CORNER ANCHORS
Fall Arrest for 2 users in separate spans
25
Edge distances and maximum spans
FALL ARREST SYSTEMS
FALL RESTRAINT
Maximum 10 m spans
Minimum edge distance of 2.5m
15m12m10m8m6m5mMaximum span
7.2m6.6m6.2m5.8m5.4m5.2mMin. Free Fall Distance
4.0m4.0m3.0m3.0m2.5m2.5mMin. Edge Distance
26
Portable Deadweight System for Rope Access
Conforms to BS EN 795,
& ISO 14567 class B&E
CE Approved to PPE Directive
Single user for Roped Access applications
Two users in a rescue situation
27
28
Separate anchor points for working
line and back up line
Internal force balanced system allows
the assembly to remain static.
Requires no attachment to structural
members
Easily moved across roof surface,
removing need for multiple
attachment points
Rope lines held away from edge of
building reducing risk of abrasion
29
Used with a 250kg Weightanka
Assembly for any roof type
Sold separately for use with
existing Weightanka or as
complete system
Aluminium, galvanised and rubber
coated parts
Minimum maintenance
Provides full fall arrest protection
before approaching edge
30
Usage
Accessanka is an accessory to Weightanka and must
always be used in combination with it.
This combination provides a mobile deadweight
anchor device for use in rope access systems in
accordance with:
Industrial Rope Access Trade Association (IRATA)
guidelines
and/or:
BS7985:2002 – Code of practice for the use of rope
access methods for industrial purposes
31
More information
Identification labels
Assembly and operating instructions
Sales Literature
Sales team
Technical support
www.keesafety.co.uk
Kee Safety Ltd
32
1 Boulton Road
Reading
RG2 0NH
United Kingdom
Tel: +44 (0) 118 931 1022
Fax: +44 (0) 118 931 1146
Email: [email protected]
www.keesafety.co.uk