powerpoint ® presentation unit 10 fastening and prying tools fastening tools hammers hammering...
TRANSCRIPT
PowerPoint® PresentationPowerPoint® Presentation
Unit 10Unit 10Fastening and Prying ToolsFastening and Prying Tools
Fastening Tools • Hammers • Hammering Technique • Nailing Method • Hatchets • Staplers •
Screwdrivers • Wrenches and Pliers • Prying Tools
Fastening Tools • Hammers • Hammering Technique • Nailing Method • Hatchets • Staplers •
Screwdrivers • Wrenches and Pliers • Prying Tools
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
The main parts of a hammer are the head, face, claw, and handle. The hammer face may be smooth or milled.
The main parts of a hammer are the head, face, claw, and handle. The hammer face may be smooth or milled.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
Carpenters use both straight-claw and curved-claw hammers.
Carpenters use both straight-claw and curved-claw hammers.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
In addition to driving nails, straight-claw hammers are used to pry boards apart and to split pieces of lumber.
In addition to driving nails, straight-claw hammers are used to pry boards apart and to split pieces of lumber.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
Curved-claw hammers provide better leverage when pulling nails than straight-claw hammers. A block of wood placed under the hammer head increases leverage and helps in removing the fastener.
Curved-claw hammers provide better leverage when pulling nails than straight-claw hammers. A block of wood placed under the hammer head increases leverage and helps in removing the fastener.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
Proper use of a hammer results in more efficient driving of nails.
Proper use of a hammer results in more efficient driving of nails.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
When possible, nail from a thinner piece into the thicker piece.
When possible, nail from a thinner piece into the thicker piece.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
Stagger nails when nailing near the end of a board. Placing the nails in a straight line may split the board.Stagger nails when nailing near the end of a board. Placing the nails in a straight line may split the board.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
To avoid splits in harder wood, blunt the end of the nail with a hammer, cut off the point of the nail, or drill a pilot hole for the nail.
To avoid splits in harder wood, blunt the end of the nail with a hammer, cut off the point of the nail, or drill a pilot hole for the nail.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
If necessary to nail into end grain, drive the nails in at an angle to increase their holding power.
If necessary to nail into end grain, drive the nails in at an angle to increase their holding power.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
Toenails should be driven in at an angle so that approximately half of the nail is in each piece of wood.
Toenails should be driven in at an angle so that approximately half of the nail is in each piece of wood.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
Tacking is a procedure for temporary nailing. The head of the nail should stick out so that it can be easily withdrawn.
Tacking is a procedure for temporary nailing. The head of the nail should stick out so that it can be easily withdrawn.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
Driving nails at an angle increases the holding power between two pieces fastened face-to-face.Driving nails at an angle increases the holding power between two pieces fastened face-to-face.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
A nail set is used to drive a nail head below the surface of the wood.
A nail set is used to drive a nail head below the surface of the wood.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
Hatchets used in the carpentry trade have a nail-pulling slot at the side of the blade.
Hatchets used in the carpentry trade have a nail-pulling slot at the side of the blade.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
A strike tacker may be used to fasten floor underlayment.
A strike tacker may be used to fasten floor underlayment.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
A hammer tacker is used to fasten insulation batts.A hammer tacker is used to fasten insulation batts.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
Heavy-duty staple guns are used to fasten vinyl flooring, insulation, roofing paper, carpet padding, screening, carpet, and ceiling tile.
Heavy-duty staple guns are used to fasten vinyl flooring, insulation, roofing paper, carpet padding, screening, carpet, and ceiling tile.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
Standard, Phillips, and square-drive (Robertson) screwdrivers are used by carpenters to drive screws.
Standard, Phillips, and square-drive (Robertson) screwdrivers are used by carpenters to drive screws.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
Screw shank and pilot holes should be drilled when fastening pieces of hard wood together with wood screws.
Screw shank and pilot holes should be drilled when fastening pieces of hard wood together with wood screws.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
When driving screws, one hand turns the screwdriver while the other hand holds it in position.
When driving screws, one hand turns the screwdriver while the other hand holds it in position.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
The screwdriver tip and blade should be properly dressed (ground) to prevent the screwdriver from slipping from the slot.
The screwdriver tip and blade should be properly dressed (ground) to prevent the screwdriver from slipping from the slot.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
Gripping tools, such as wrenches and pliers, are used to tighten bolts.
Gripping tools, such as wrenches and pliers, are used to tighten bolts.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
When using an adjustable wrench, be sure it is tightly adjusted to the nut. Pull the wrench so that the force is on the side of the fixed jaw.
When using an adjustable wrench, be sure it is tightly adjusted to the nut. Pull the wrench so that the force is on the side of the fixed jaw.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
For power tasks, a pair of pliers with an open grip span no greater than 3 1/2″ and a closed grip span of at least 2″ should be used.
For power tasks, a pair of pliers with an open grip span no greater than 3 1/2″ and a closed grip span of at least 2″ should be used.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
A ripping bar is used to pry boards apart and remove large nails or spikes.
A ripping bar is used to pry boards apart and remove large nails or spikes.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
A ripping chisel may be used to pry materials apart.A ripping chisel may be used to pry materials apart.
Unit 10 — Fastening and Prying ToolsUnit 10 — Fastening and Prying Tools
A nail claw is used to pull nails driven flush with the lumber surface so they can be pulled out with a hammer or ripping bar.
A nail claw is used to pull nails driven flush with the lumber surface so they can be pulled out with a hammer or ripping bar.