pom-2 by mallikarjun
TRANSCRIPT
-
8/8/2019 POM-2 by Mallikarjun
1/13
Praxis Business School
Production & Operations Management-II
Mid-Term Paper submitted to:-
Prof. Rajiv Misra
Prepared By:-
Mallikarjuna Reddy Gooli (B09010)
-
8/8/2019 POM-2 by Mallikarjun
2/13
5S
What Is 5S?
5S is methodology for organizing, cleaning, developing and sustaining aproductive work environment .The methodology originates from a Japanese
housekeeping idea named because of the five Japanese words each beginning with the
letter se or shi. They are Se-iri , Se-iton, Se-iso, Se-iketsu and Shi-tsuke.
Definitions:Seiri(Sort)
Distinguish the necessary things from the unnecessary and dispose of the unnecessary.
This is the priority area.
Seiton(Straighten)
Arrange the necessary items in an orderly fashion so they are easily accessed and
selected for use.Seiso(Scrub)
Clean your workplace to keep floors and equipment tidySeiketsu(Standardize)
Continually maintain the order, neatness and cleanliness.Shitsuke(Sustain)
Do things spontaneously without being told. Train everyone in the workplace to follow
good work habit so that it is a matter of personal pride and self respect.
Problems Addressed: When applied to a factory, 5S can help to solve the following types of
common problems:
y Space crowded with parts and toolsy Unneeded items stacked between workersy Excess inventory on the floory Excess items and machines hinder process flowy Equipment is dirty and not serviced regularlyy Needed equipment, such as tools, is difficult to find.
Process: The following flowchart explains the implementation process of5S.
Sort
Straighten
Scrub
Standardize
u tain
Conduct initial factory wide cleaning. Identify the
necessary from the unnecessary, discard the unnecessary
Put necessary items in order, mark undecided
Clean works ace to eliminate causes of roblems of waste
Create a manual and policies, draw up checklists
5S becomes a way of life and everybodys business
R
E
P
A
T
-
8/8/2019 POM-2 by Mallikarjun
3/13
Keys to successful implementation:
y Get everybody to participate.y Believe in the workers good nature.y Let organizers understand their role.y Make a plan with schedules and targets.y Advances step by step steadily.y Reach agreement with each other.
Challenges and Pitfalls:
Everyone in the organization must be fully committed to implementing the 5S process.
Workers and management at all levels must take responsibility to keep their work area clean and
orderly if5S is to be achieved.
The Poka-Yoke SystemPoka-yoke (poh-kah yoh-keh) was coined in Japan during the 1960s by Shigeo Shingo who
was one of the industrial engineers at Toyota. Shigeo Shingo is also credited with creating and
formalizing Zero Quality Control (poka-yoke techniques to correct possible defects + source
inspection to prevent defects equals zero quality control).
Definition:
The term poka-yoke means mistake-proofing or more literally avoiding (yokeru) inadvertent
errors (poka). Ideally, poka-yokes ensure that proper conditions exist before actually executing a
process step, preventing defects from occurring in the first place. Where this is not possible, poka-
yokes perform a detective function, eliminating defects in the process as early as possible.
To err is human, but still errors can be limited by applying the intelligence which the human
being possesses. The following are the reasons for doing such errors.
Causes Effects
1.Distraction Defects(Quality)
2.Confusion Insufficient number(Quantity)
3.Lack of practice Accidents(Safety)
4.Uncertainity Work delay
Classifications by Dr. Shigeo Shingo:
Judgment inspectiony Inspection in quality
Informative inspectiony Uses data gained from inspection to control the process and prevent defects.
Examples: Traditional SPC and repeated checks and self checks in ZQC
Source inspectiony Before the fact at source, before reaching customer or Forcing function
-
8/8/2019 POM-2 by Mallikarjun
4/13
Poka-Yoke devices:
1. Aprevention device engineers the process so that it is impossible to make a mistake at all.
Ex: A 3.5 inch computer diskette
2. Adetection device signals the user when a mistake has been made, so that the user can quickly
correct the problem
Ex: Small dish for push buttons
Push buttons:
In the old method, a worker began by taking two springs out of a large parts box and then
assembled a switch.
In the new approach, a small dish is placed in front of the parts box and the worker's first task
is to take two springs out of the box and place them on the dish. Then the worker assembles the
switch. If any spring remains on the dish, then the worker knows that he or she has forgotten to insert
it.
Example:
Carbon Credit and effects on Operations
Environmental management:
Environmental management is not merely managing the environment but its the management
of human interaction with; and impact upon the environment in order to conserve the environment for
mankinds sake. Managing environment is the biggest issue these days which is being faced by
everyone everywhere across the globe. Initially, the Environmental Law was perceived as one of the
most important tools of environmental management. However, Protection of environment from
degradation has now not just remained a legal issue but a management issue as well.
Market Based Instruments (MBI) for Environmental Benefits:Market Based Instruments refer to the environmental policies which encourage change in
technology, behaviour or products through financial incentives like subsidies, taxes, price
differentiation or market creation.
What does Carbon Credit mean?
A permit that allows the holder to emit one ton of carbon dioxide; Credits are awarded to countries or
groups that have reduced their green house gases (GHG) below their emission quota.
-
8/8/2019 POM-2 by Mallikarjun
5/13
Its goal is to stop the increase of carbon dioxide emissions. The Kyoto Protocolpresents
nations with the challenge of reducing greenhouse gases and storing more carbon. A nation that finds
it hard to meet its target of reducing GHG could pay another nation to reduce emissions by an
appropriate quantity. The carbon credit system was ratified in conjunction with the Kyoto Protocol.
For example, if an environmentalist group plants enough trees to reduce emissions by one
ton, the group will be awarded a credit. If a steel producer has an emissions quota of 10 tons, but isexpecting to produce 11 tons, it could purchase this carbon credit from the environmental group.
The carbon credit system looks to reduce emissions by having countries honour their emission quotas
and offer incentives for being below them.
Simply put, one carbon credit is equivalent to one tonne of carbon dioxide or its equivalent
greenhouse gas (GHG). Carbon credits are Entitlement Certificates issued by the United Nations
Framework Convention on Climate Change (UNFCCC) to the implementers of the approved Clean
Development Mechanism (CDM) projects.
Effects on Operations:
Induces pressure on the organisations to adopt/invent efficient operations techniques in order
not to cross the carbon limits. India is still not a signatory to the Kyoto Protocol, which in a way, is aroad-block for effectively carrying out environmental management by the industries. Currentlycompanies like Jindal Stainless, EssarSteel, Hyderabad Chemicals, Paschim Hydro Energy P. Ltd,
The Andhra Pradesh Paper Mills Ltd, have been making use of market based instruments like CarbonCredits in their businesses.
Organisations would also encourage use of reusable lunch bags / cups etc. in their cafeteria /
lunch rooms which helps in avoiding use of plastic / paper, use of hand towels in toilets and lunch
rooms instead of paper towels and electric dryers.Supporting the commercial development of new technologies to reduce environmental impact
may be a suitable strategy for companies involved in natural resource intensive production activities,
such as brewers, electricity providers and mining companies
-
8/8/2019 POM-2 by Mallikarjun
6/13
Cement Manufacturing ProcessIntroduction:
Cement is an essential material for today's society because concrete is made from cement,
which is an inevitable element for housing, commercial and infrastructure development. Measured ona kilogram per capita basis, concrete is 2nd most widely consumed material in the world, second only
to water. Cement manufacturing process will have -Local impacts (landscape disturbance, dustemission) and Global impacts (CO2, SOx andNOx emissions).
Because of these impacts, sustainable development has recently become a major strategic
issue for cement manufacturers around the world. Cement industry is giving very specific and seriousattention for managing CO2 emission.
Types of cement:There are many types of cement in the market to suit every need. Some of them which are
included in the revised IS : 456-2000 are as follows:
Ordinary Portland Cement 33, 43, 53 grade (OPC), 53-S (Sleeper Cement)
Portland Pozzolana Cement (PPC), both Fly Ash and Calcined Clay based Rapid Hardening Portland Cement
Portland Slag Cement (PSC)
Sulphate Resisting Portland Cement (SRC) Low Heat Portland Cement
Hydrophobic Cement
Even though only Ordinary Portland Cement is graded according to strength, the other cementstoo have to gain a particular strength. 33, 43 and 53 grade in OPC indicates the compressive strength
of cement after 28 days when tested as per IS: 4031-1988, eg, 33 Grade means that 28 days of
compressive strength is not less than 33N/mm2 (MPa) . Similarly for 43 grade and 53 grade the 28days compressive strength should not be less than 43 and 53 MPa respectively. 43 and 53 grade are
also being introduced in PPC and PSC shortly by the Bureau of Indian Standards (BIS)
Manufacturing process:
Process Flow Diagram
Raw Materials
The main raw materials used in the cement manufacturing process are limestone, sand, shale, clay,
and iron ore. The main material, limestone, is usually mined on site while the other minor materialsmay be mined either on site or in nearby quarries. Another source of raw materials is industrial by-
products. The use of by-product materials to replace natural raw materials is a key element in
achieving sustainable development.
Raw Material Preparation
Mining of limestone requires the use of drilling and blasting techniques. The blasting techniques use
the latest technology to insure vibration, dust, and noise emissions are kept at a minimum. Blastingproduces materials in a wide range of sizes from approximately 1.5 meters in diameter to small
particles less than a few millimetres in diameter. Material is loaded at the blasting face into trucks for
transportation to the crushing plant. Through a series of crushers and screens, the limestone is reducedto a size less than 100 mm and stored until required.
-
8/8/2019 POM-2 by Mallikarjun
7/13
Depending on size, the minor materials (sand, shale, clay, and iron ore) may or may not be crushed
before being stored in separate areas until required.
Raw Grinding
In the wet process, each raw material is proportioned to meet a desired chemical composition and fed
to a rotating ball mill with water. The raw materials are ground to a size where the majority of thematerials are less than 75 microns. Materials exiting the mill are called "slurry" and have flowability
characteristics. This slurry is pumped to blending tanks and homogenized to insure the chemical
composition of the slurry is correct. Following the homogenization process, the slurry is stored in
tanks until required.
In the dry process, each raw material is proportioned to meet a desired chemical composition and fed
to either a rotating ball mill or vertical roller mill. The raw materials are dried with waste process
gases and ground to a size where the majority of the materials are less than 75 microns. The drymaterials exiting either type of mill are called "kiln feed". The kiln feed is pneumatically blended toinsure the chemical composition of the kiln feed is well homogenized and then stored in silos until
required.
Pre-processing
Whether the process is wet or dry, the same chemical reactions take place. Basic chemical reactions
are: evaporating all moisture, calcining the limestone to produce free calcium oxide, and reacting withthe calcium oxide with the minor materials (sand, shale, clay, and iron). This results in a final black,
nodular product known as "clinker" which has the desired hydraulic properties.
In the wet process, the slurry is fed to a rotary kiln, which can be from 3.0 m to 5.0 m in diameter and
from 120.0 m to 165.0 m in length. The rotary kiln is made of steel and lined with special refractorymaterials to protect it from the high process temperatures. Process temperatures can reach as high as
1450oC during the clinker making process.
In the dry process, kiln feed is fed to a pre-heater tower, which can be as high as 150.0 meters.Material from the pre-heater tower is discharged to a rotary kiln with can have the same diameter as a
wet process kiln but the length is much shorter at approximately 45.0 m. The pre-heater tower androtary kiln are made of steel and lined with special refractory materials to protect it from the high
process temperatures.
Regardless of the process, the rotary kiln is fired with an intense flame, produced by burning coal,
coke, oil, gas or waste fuels. Pre-heater towers can be equipped with firing as well.
The rotary kiln discharges the red-hot clinker under the intense flame into a clinker cooler. The
clinker cooler recovers heat from the clinker and returns the heat to the pyroprocessing system thusreducing fuel consumption and improving energy efficiency. Clinker leaving the clinker cooler is at a
temperature conducive to being handled on standard conveying equipment.
Finish Grinding and Distribution
The black, nodular clinker is stored on site in silos or clinker domes until needed for cement
production. Clinker, gypsum, and other process additions are ground together in ball mills to form thefinal cement products. Fineness of the final products, amount of gypsum added, and the amount of
process additions added are all varied to develop a desired performance in each of the final cement
products.
-
8/8/2019 POM-2 by Mallikarjun
8/13
Each cement product is stored in an individual bulk silo until needed by the customer. Bulk cement
can be distributed in bulk by truck, rail, or water depending on the customer's needs. Cement can also
be packaged with or without colour addition and distributed by truck or rail.
Raw material
Crusher/Stacker & Reclaimer
SixStage Pre heater
90% calsination over
Raw Material Roller Press
Lime stone 90-96%
Hematite 2-5%
Bauxite 1-3%
Grinding Mill
Rotary Kiln
(1200-1450
C)Clinker -120 C
Clinker
stora e
Roller
Press
Cement
Mill
Packaging
Unit
Storage silo
Dispatch
Clinker coolin
Add Gypsum
Grinding of clinker
Bulk/paper/HDPE bagsRoad/Rail
-
8/8/2019 POM-2 by Mallikarjun
9/13
Productivity:
y Identify the appropriate bottleneck and try to reduce idle time of bottlenecky Make sure that the idle time of each machines should as minimum as possible because the
cost of operating machines very expensive
y Adopt to the latest technology to improve efficiencyy Raw material procurement in advancey Have a back up facility for electricityy Employee need to very well trained with usage of machines
Quality:
y Open the bag and take a good look at cement, there should be no lumpsy Try to minimize release of dust particles into atmosphere by using latest technology processy Make sure that the surroundings should be moist free as the quality of cement would be
effected because of moisture
yUse appropriate technologies to inspect the quality as the production process is Line
y Focus more on air tight packaging as cements strength gets diluted when exposed to moisturey Purchase raw material which is free from impurities which envisages further efficiency of
machines
Delivery:
y Use Information Systems to have good information visibility of stock across thedealers/retailers and different plants
y Establish rail/road ways if required for transporting finished products from planty Have own vehicles to reduce dependency on third party transport service providers
Safety:
y Avoid actions that cause dust to become airborney Avoid inhalation of dust and contact with skiny Provide suitable working uniform for the workers as the environment is dustyy Provide sufficient no of exhaust fans to send out accumulated dust particles
Cost:
y Locate the production near to the source of raw materialy Produce cement in large quantity to fully utilize machineryy Use wastage to produce by products
Moral:
y Provide accidental and health insurance for employees as the health of workers would beeffected due to dust particles
y Conduct floor meetings to address issues of workers
-
8/8/2019 POM-2 by Mallikarjun
10/13
y Est lish faciliti s li schoolhospital and parks with in the town ship of employees
Suppl i i D upli poi oduct postponement
(Offset Printers)
Suppl chain of Offset Printing
y The raw material aper of different si es ,colours and quality ) will be procured from theTier-1 suppliers of papers
y The product belongs to MTO category of productionDecoupling Point:
y The customer would be known to the producer before the productis being producedy Ifthe decoupling point moves towards the rightthen it would be very difficultto matchcustomer requirements with the pre defined format of magazines and contenty Therefore in the case ofOffset printers the decoupling point and the product postponement
exactly coincides
Product postponement:
y The production department doesnt cut paper until an order comes from the customer
Purc
se
Planeapaer
of differentcolors and
quality
Prepare
Content andPage layout
usingcomputer
Print the Pageswith required
quality andquantity
elivery the
order with incommited
date
DecouplingPoint
Product
Postponement
-
8/8/2019 POM-2 by Mallikarjun
11/13
y This will delay the process of production and the production will be started according theorder
y This approach reduces the forecast risk and the risk of inventory getting piled up because ofdecrease in demand
y The challenge would be to deliver the order within the committed period
Material Resource Planning
A material requirement planning is a technique that uses the bill of material, inventory data
and a master schedule to calculate requirements for material. MRP time phases material requirements
based on setbacks defined by a combination of the bill of material structure and assembly lead times.
The result of an MRP plan is a material plan for each item found in the bill of material structure which
indicates the amount of new material required, the date on which it is required - the new schedule
dates for material that is currently on order. If routings, with defined labour requirements areavailable, a capacity plan will be created concurrently with the MRP material plan.
Advantages:
y Manage production planning effectively.Visibility to forecasts as well as sales orders makesproduction planning more effective and allows for more detailed analysis of recommendations
drawn from data. The result is better production planning and control. Site-specific inventory
planning provides flexibility to manage each site.
y Issue purchase orders easily and efficiently. Material Requirements Planning suggestions canbe easily converted to purchase orders which helps ensure that your flow of materials
synchronizes with production planning. By combining multiple requirements into a minimum
number of orders, workflow is accelerated and simplified.
Structure of Material Resource Planning
Bill of material
Lead times
nventory
aterial
reuirements
programs CO
mputer andsoftware
Purchasing
Data
MRPby
Period
MRP by
Datereport
Purchase
order report
xception
reports
Order early
or late
Master
Production
Schedule
-
8/8/2019 POM-2 by Mallikarjun
12/13
Material Resource planning for a product
A master production schedule, a bill of material, inventory and purchase records, and lead times of
each item are the ingredients of a material requirements planning.
Lets consider a product which has requires three components
Components:
1 .X
2. Y
3. Z
On-hand Inventory
Component On Hand
X 0Y 10
Z 0
Gross Material Requirements plan for the Product
Component 1 2 3 4 5 6 7 8 Lead Time
X(Required Date) 30
X(Order Release date) 30 1
Y( Required Date) 70
Y(Order Release date) 70 2
Z Required Date) 80
Z(Order Release date) 80 4
Net material planning
periodX(Lot Size=1,Lt=1) 1 2 3 4 5 6 7 8
Gross Requirements 30
Scheduled Receipts
On Hand 0 0 0
Net Requirements 30
Planned Order receipts 30
Planned Order release 30
Period in week
-
8/8/2019 POM-2 by Mallikarjun
13/13
Component
Y(Lot Size=1),LT=2 1 2 3 4 5 6 7 8
Gross Requirements 70
Scheduled Receipts
On Hand 10 10 10 10 10
Net Requirements 60
Planned Order receipts 60
Planned Order release 60
Component
Z(Lot Size=1),LT=4 1 2 3 4 5 6 7 8
Gross Requirements 80
Scheduled Receipts
On Hand 0 0 0 0 0 0 0 0
Net Requirements 80
Planned Order receipts 80
Planned Order release 80