plastomers gradeslate productguide
TRANSCRIPT
FDA Note FDA Statement
1a Complies with FDA regulation 21 CFR 177.1520 “Olefin polymers” paragraph (c)3.2a, and may be usedas articles or components of articles intended for use in contact with food, including use in articles usedfor packing or holding food during cooking.
1b Complies with FDA regulation 21 CFR 177.1520 “Olefin polymers” paragraph (c)3.2a, and may be usedas articles or components of articles intended for use in contact with food, including use in articles usedfor packing or holding food during cooking. Finished articles may contact all food types identified in Table1 of CFR 176.170(c) only under Conditions of Use B through H described in Table 2 of 21 CFR176.170(c), at temperatures not in excess of 212°F.
2 Complies with FDA regulation 21 CFR 177.1520 “Olefin polymers” paragraph (c)3.1a, and may be usedas articles or components of articles intended for use in contact with food, except for articles used forpacking or holding food during cooking.
3 Complies with FDA regulation 21 CFR 177.1520 “Olefin polymers” paragraph (c)3.6, provided that it isused only as a blend component with specific regulated FDA materials to make films no thicker than 4 mils.
4 Complies with FDA Regulation 21 CFR 175.105 “Adhesives” and may be used to prepare adhesives thatare used as components of articles intended for use in packaging, transporting or holding food, subjectto the restrictions provided in 21 CFR 175.105 (a) (2).
5 Complies with FDA regulation 21 CFR 177.1520 “Olefin polymers” paragraph (c)3.2a, and may be usedas articles or components of articles intended for use in contact with food, including use in articles usedfor packing or holding food during cooking.
6 Complies with FDA regulation 21 CFR 177.1520 “Olefin polymers” paragraph (c)3.2c, and may be usedin materials or articles that contact food. Finished articles may contact all food types identified in Table 1of CFR 176.170(c) only under Conditions of Use C through H described in Table 2 of 21 CFR 176.170(c),at temperatures up to hot-filled or pasteurized above 150°F (less than 212°F).
©2006 Exxon Mobil Corporation. The user mayforward, distribute, and/or photocopy this copy-righted document only if unaltered and complete,including all of its headers, footers, disclaimers,and other information. ExxonMobil does not guar-antee the typical (or other) values. Typical valuesonly represent the values one would expect if theproperty were tested in our laboratories with ourtest methods on the specified date. Some productproperties are not frequently measured, andaccordingly typical values are not based upon astatistically relevant number of tests. The informa-tion in this document relates only to the namedproduct or materials when not in combination withany other product or materials. We based theinformation on data believed to be reliable on thedate compiled, but we do not represent, warrant,or otherwise guarantee, expressly or impliedly, themerchantability, fitness for a particular purpose,suitability, accuracy, reliability, or completeness ofthis information or the products, materials, orprocesses described. The user is solely responsi-ble for all determinations regarding any use andany process. We expressly disclaim liability for anyloss, damage, or injury directly or indirectly suf-fered or incurred as a result of or related to anyoneusing or relying on any of the information in thisdocument. There is no warranty against patentinfringement, nor any endorsement of any productor process, and we expressly disclaim any con-trary implication. The terms, “we,” “our,”“ExxonMobil Chemical,” or “ExxonMobil” are usedfor convenience, and may include any one or moreof ExxonMobil Chemical Company, Exxon MobilCorporation, or any affiliates they directly or indi-rectly steward. ExxonMobil, the “Interlocking X”Device, Exact, and Exxpol are trademarks ofExxon Mobil Corporation.
Products with densities ≥0.880 g/cc may not beavailable in all regions.
Worldwide Sales OfficesAmericasExxonMobil Chemical13501 Katy Frwy.Houston, Texas 77079Tel. 281.584.7614Fax 281.588.2577
EuropeExxonMobil ChemicalHermeslaan, 2B-1831 Machelen, BelgiumTel. 32.02.722.4363Fax 32.02.722.4369
Asia PacificExxonMobil Chemical1 HarbourFront Place#06-00 HarbourFront Tower OneSingapore 098633Tel. 65.6885.8473Fax 65.6885.8488
exactplastomers.comexxonmobilchemical.com P
rinte
d in
U.S
.A. •
Aug
ust 2
006
• 11
9-08
06-1
00 •
2,0
00
EXACT™ Plastomers
Grade Slate And Product Guide
A Well-Balanced Portfolio For Your Precise Needs.
FDA StatusTy
pe
of
Eth
ylen
e C
op
oly
mer
(CA
S#
2521
3-02
-9)
(CA
S#
2508
7-34
-7)
EXACT Plastomers Density Melt Index FDA NoteGrade (g/cc) (dg/min) 3024 0.905 4.5 1a
3035 0.900 3.5 1a
3128 0.900 1.2 1a
4006 0.880 10 4
4053 0.888 2.2 3
4049 0.873 4.5 4
3040 0.900 16.5 2
3131 0.900 3.5 1b
3132 0.900 1.2 1b
3139 0.900 7.5 1b
4056 0.883 2.2 4
4150 0.895 3.5 2
4151 0.895 2.2 1b
0201 0.902 1.1 5
0201FX 0.902 1.1 1b
0203 0.902 3.0 5
0210 0.902 10 6
0230 0.902 30 6
5061 0.868 0.5 6
5062 0.860 0.5 6
5101 0.902 1.1 5
5171 0.870 1.0 6
5181 0.882 1.1 6
5361 0.860 3.0 6
5371 0.870 5.0 6
8201 0.882 1.1 6
8203 0.882 3.0 6
8210 0.882 10 6
8230 0.882 30 6
(CA
S#
2622
1-73
-8)
BUTENE HEXENE OCTENE
EX
AC
T™
PLA
ST
OM
ER
S–
FOR
YO
UR
PR
EC
ISE
NE
ED
S
EXACTTM Plastomers are a family of ethylene alpha olefin copolymers produced using ExxonMobil Chemical’s ExxpolTM
metallocene catalyst technology. They offer a unique set of properties in which rubber-like properties and plastic process-
ability are realized in one material. Used neat or as polymer modifiers, EXACT Plastomers offer endless possibilities to
bring value to your products. They enhance the toughness, clarity and sealing performance of flexible packaging materials.
In molded and extruded products, they improve impact strength and flexibility. The combination of comonomer type and
process technology offered by ExxonMobil results in a wide range of products designed to serve customers’ unique needs:
Butene Good film properties, including high oxygen transmission rates for fresh produce packaging
Good property balance in PP-based TPOs
Hexene Outstanding toughness and puncture resistance for film applications
Excellent hot-tack strength and seal-through contamination in film heat-seal applications
Octene Excellent toughness and heat-seal properties for film applications
Easy processing for all applications due to shear thinning characteristics
Low density grades for outstanding low temperature impact resistance in PP-based TPOs
Typical Applications and Properties of EXACT™ Plastomers GradesPolymer Modification
Film/Flexible Packaging
1. EXACT 0201FX is EXACT 0201 with slip and anti-block
BLOWN FILM
CAST FILM
BUTENE HEXENE OCTENE
5061
5171
Ethylene Octene 8230
8210
8203
0230
0210
51818201
4056 4151
4150
3139
Ethylene Hexene
3040
4049
4006
4053
3035 3024
3128
Ethylene Butene
EXACT™ Plastomers Grade Slate
Density (g/cc)
0.86
100
10
1
00.87 0.88 0.89 0.90 0.91
Mel
t In
dex
(dg
/min
)
5361
5062
31310203
5371
51010201
0201FX
3132
BLOWN FILM
CAST FILM
3024 • 3024 0.905 4.5 100 16 90 97
3035 • 3035 0.900 3.5 70 16 94 88
4006 • • 4006 0.880 10 17 6 79 60
4053 • 4053 0.888 2.2 27 22 84 70
0201 • • • 0201 0.902 1.1 68 >21 90 97
0203 • • • 0203 0.902 3.0 76 >21 87 94
0210 • • 0210 0.902 10 76 14.8 85 96
0230 • • 0230 0.902 30 80 11 88 95
5061 • • 5061 0.868 0.5 12 >7 65 53
5062 • • 5062 0.860 0.5 6 >4 57 43
5101 • • • 5101 0.902 1.1 88 >21 90 98
5171 • • 5171 0.870 1.0 13 >8 70 55
5181 • • 5181 0.882 1.1 26 >14 84 73
5361 • • • 5361 0.860 3.0 4 1.4 52 36
5371 • • 5371 0.870 5.0 13 >5 70 64
8201 • • • 8201 0.882 1.1 26 >14 78 67
8203 • • • 8203 0.882 3.0 28 >10 80 73
8210 • • 8210 0.882 10 26 >8 79 74
8230 • • 8230 0.882 30 26 6 75 77
3128 • • 3128 0.900 1.3 73/77 60/52 670 924053 • • • 4053 0.888 2.2 34/38 57/50 140 693132 • • 3132 0.900 1.2 73/78 74/74 1330 964056 • 4056 0.883 2.2 30/34 78/72 1030 724151 • • • 4151 0.895 2.2 56/61 78/72 1215 880201/0201FX1 • • • 0201 0.902 1.1 68/75 56/61 610 965101 • • • 5101 0.902 1.1 73/83 66/63 600 995181 • • • 5181 0.882 1.1 29/35 56/54 225 718201 • • • 8201 0.882 1.1 28/33 66/52 270 71
3024 • 3024 0.905 4.5 85/97 48/32 140 97
4053 • • 4053 0.888 2.2 37/36 65/46 120 694049 • 4049 0.873 4.5 533040 • 3040 0.900 16.5 70/76 55/47 100 953131 • • • 3131 0.900 3.5 67/75 74/61 1050 943139 • 3139 0.900 7.5 68/76 66/56 240 954150 • • • 4150 0.895 3.5 56/59 78/70 540 894151 • • 4151 0.895 2.2 56/64 85/69 940 880203 • • • 0203 0.902 3.0 73/84 66/51 230 950210 • 0210 0.902 10 70/77 44/35 90 950230 • 0230 0.902 30 69/74 32/25 70 958203 • • • 8203 0.882 3.0 33/38 55/45 170 728210 • • 8210 0.882 10 30/32 35/29 70 738230 • • 8230 0.882 30
EXACT Blow- Injection EXACT Density Melt Index Flexural Ultimate Tensile Hardness DSC MeltingPlastomers Extrusion Molded Molding TPOs Foams Rotomolding Plastomers 190°C, 2.16 kg Modulus Strength Peak, 10°C/minGrade Packaging Grade (g/cc) (dg/min) 1% Sec (MPa) (MPa) (Shore A) (°C)
Test Method Based on: ExxonMobil ASTM D-1238 ASTM D-790 ASTM D-638 ASTM D-2240 ExxonMobil
EXACT Heat Fresh Cling Extrusion Batch Toughness EXACT Density Melt Index 1% Secant Modulus Tensile Strength Dart Drop DSC MeltingPlastomers Seal Produce Layer in Coating Inclusion Layer Plastomers 190°C, 2.16 kg MD/TD MD/TD Impact, Peak, 10°C/minGrade Layer Packaging Stretch Film Bag Film Grade (g/cc) (dg/min) (MPa) (MPa) F50 (g) (°C)
Test Method Based on: ExxonMobil ASTM D-1238 ASTM D-882 ASTM D-882 ASTM D-1709(A) ExxonMobil