piston balanced pressure open - kimray, inc · 2020-06-24 · 325 sma pb po-d w/ti250 250 rtr eli...
TRANSCRIPT
www.kimray.comE3:20.1
Issued 6/18Current Revision:Update image
BALANCED MOTOR VALVES
PISTON BALANCED PRESSURE OPEN
Stem and Seat AssemblyMotor Valve Diaphragm PressureUpstream PressureDownstream Pressure
Travel Indicator Stem
Stem
Cage
Seat
Oil
Piston
APPLICATIONS: Pilot operated oil or water valve for separators, meters, and water knockouts where a reduced signal pressure is available, and where freezing occurs due to a higher pressure drop.
FEATURES: Piston balanced single seat 10 psig minimum diaphragm pressure Standard 303 stainless valve stem Reinforced oil resistant synthetic rubber diaphragms and seats Easy to service and repair Available for pressure opening or pressure closing service
CERTIFICATIONS: Canadian Registration Number (CRN): 0C15804.24567890NTY (Ductile) 0C15621.24567890NTY (Steel)
SUPPLY PRESSURE: 10 to 35 psig.
OPERATION TEMPERATURE: Standard - 225°F. Max. Heat Modified - 350°F. Max.
CAPACITY: Refer to Table of Contents.
Kimray is an ISO 9001- certified manufacturer.
Cf & Cv VALUESLine Size Trim Size Cf Cv
2" 1.50" 0.79 23.33" 2.25" 0.79 43.84" 3.00" 0.79 70.16" 4.88" 0.79 277.0
www.kimray.comE3:20.3Issued 4/20
Current Revision:Add lifting ring
BALANCED MOTOR VALVES
PISTON BALANCED PRESSURE OPENDUCTILE IRON
ANGLE VALVES AVAILABLE: THRU VALVES AVAILABLE:
ELA 2" SCRD. 250 SMA PB PO-D W/TI 500 500 RFPELC 2" FLGD. 225 FMA PB PO-D W/TI 250 250 RFPELG 3" SCRD. 325 SMA PB PO-D W/TI 250 250 RTRELI 3" FLGD. 325 FMA PB PO-D W/TI 250 250 RTRELM 4" FLGD. 425 FMA PB PO-D W/TI 250 250 RTT
To remove Piston 1807, use Spanner Wrench 1471SNW. To remove Pistons 1859 and 1863, use Spanner Wrench 1859SNW. Note: Drawing depicts 2" valve. Piston design varies, install with spanner wrench holes on top. For dimensions refer to Table of Contents.
EYA 2" SCRD. 250 SMT PB PO-D W/TI 500 500 RFPEYC 2" FLGD. 225 FMT PB PO-D W/TI 250 250 RFPEYG 3" SCRD. 325 SMT PB PO-D W/TI 250 250 RTREYI 3" FLGD. 325 FMT PB PO-D W/TI 250 250 RTREYM 4" FLGD. 425 FMT PB PO-D W/TI 250 250 RTT
*These are recommended spare parts and are stocked as repair kits.
CAT. SIZE MOTOR OPER. MAX NO. TYPE VALVE PRES. W.P. KIT
CAT. SIZE MOTOR OPER. MAX NO. TYPE VALVE PRES. W.P. KIT
1
2
3
4
5
7
8
9
10
6
13
15
16 17
18
19
20
21
23
24
22
25
26
27
28
29
11
12
14
7
26
33
32
31
30
34
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Kimray is an ISO 9001- certified manufacturer.
ITEM QTY. DESCRIPTIONPART NO.
2 INCH 3 INCH 4 INCH
1 1 LOCK NUT 173 906
2 1
SEAT 7498HSN 7499HSN ----
SEAT ---- 165HSN
SEAT DISC ---- 160
3 1 RATIO PLUG 332DEL 333DEL 334
4 1 GASKET 276 277 309
5 1 STEM 1809 327 328
6 1 CAGE ‡ 1751 1759 1761
7 2 O RING 774HSN 329HSN 1872
8 1 O RING 154HSN 155HSN 155
9 BOLT 1672 x 6 1672 x 8
10 1 STEM ASSEMBLY 1808 1858
11 1 STEM GUIDE 2463 2464
12 1 HOUSING 1689 1868D 1869D
13 NUT 241 x 8 241 x 10
14 BOLT 236 x 8 191 x 10
15 1 DIAPHRAGM 6810 6811
16 1 TRAVEL INDICATOR STEM 1687 1733
17 1 TRAVEL INDICATOR HOUSING 1686
18 1 GASKET 1784
19 1 SPRING 1936 551
20 1 BONNET 1671 1867
21 1 BREATHER PLUG 147
22 1 DIAPHRAGM PLATE 133 134
23 1 SPRING 1678 2268
24 1 O RING 1107HSN 639HSN 639
25 2 BACK UP 149T 150T
26 2 BACK UP 1685 1870 1871
27 1 CYLINDER 1679 1861 1865
28 1 O RING 808HSN 802HSN 2083
29 1 O RING 329HSN 330HSN 331
30 1 PISTON SEAL RETAINER 1806 1860 1864SS6
31 1 PISTON 1807 1859 1863SS6
32 1 ORING 265HSN 154HSN 154
33 1 REMOVABLE SEAT 1752PH 1760PH 1762PH
34 1
BODY
SCREWED ANGLE 1819 2379 ----
SCREWED THRU 3081 3086 ----
FLANGED ANGLE 4348 2382 2383
FLANGED THRU 3083 3087 3090
2 LIFTING RING (not shown) ---- 7559
‡ Delrin Cage available on request for 4 inch valves
*
*
*
*
*
*
*
*
*
*
*
*
*
*
www.kimray.comE3:30.1
Issued 1/13Current Revision:Change Logo
LIQUID CAPACITY CHARTS
300 psig Maximum W.P. Valves
CAPACITY-Bbls. Water/Day, Steady Flow
For gravity correction, multiply the above figures byWhere “G” is the specific gravity of the flowing liquid.NOTE: Flow rates are for steady flow conditions over a 24 hour period. Corrections should be made to deal with intermittent flow conditions.
1G
PRESSURE DROP
ACROSS VALVEPSIG
VALVE SIZE - INCHES
2 3 4 6
12345
10152030405060708090
100120140160180200220240260280300325350375400
8001,1501,4001,6001,8002,5503,1003,6004,4005,1005,7006,2506,7507,2007,6508,0508,8509,550
10,20010,80011,40011,95012,50013,00013,50013,95014,50015,05015,60016,100
1,5002,1002,6003,0003,3504,7505,8006,7008,2009,500
10,60011,60012,55013,40014,20015,00016,40017,75018,95020,10021,20022,20023,20024,15025,05025,95027,00028,05029,00029,950
2,4003,4004,1504,8005,3507,6009,300
10,75013,15015,20016,95018,60020,10021,45022,75024,00026,30028,40030,35032,20033,95035,60037,20038,70040,15041,55043,25044,90046,50048,000
9,50013,45016,45019,00021,25030,05036,80042,50052,00060,05067,15073,55079,45084,95090,10094,950
104,050112,350120,150127,400134,300140,850147,150153,150158,900164,500171,200177,700183,900189,950
www.kimray.comE3:40.1
Issued 6/13Current Revision:Remove Cast Iron
BALANCED MOTOR VALVES
CAGE & HARD SEAT
NOTES:
Removable seat and cage is standard in Piston Balanced Motor Valves. But is optional in Diaphragm Balanced Motor Valve. To order specify valve model, then add “with removable seat.”
Kimray is an ISO 9001- certified manufacturer.
www.kimray.comE3:50.1
Issued 6/20Current Revision:Add LPHV valve
BALANCED MOTOR VALVES
DIMENSIONS
ANGLE DIMENSIONS THRU DIMENSIONS
VALVE A B C D E F2" S/FMA 6 1/2 9 8 1/2 4 1/4 3 4 1/4
3" S/FMA 8 1/2 11 3/4 10 1/4 5 1/2 3 3/4 5 1/2
4" FMA 8 1/2 12 1/2 11 6 1/2 4 1/2 6 1/2
6" FMA 10 3/4 — 19 3/4 10 1/4 5 1/2 7 11/16
VALVE A B C D E F2" SMT 6 1/2 10 3/8 9 7/8 2 1/8 — 8 1/2
2" FMT 6 1/2 10 3/8 9 7/8 — 3 9
3" SMT 8 1/2 13 5/16 11 9/16 2 7/8 — 12
3" FMT 8 1/2 13 5/16 11 9/16 — 3 3/4 12 3/16
4" FMT 8 1/2 14 7/8 13 3/8 — 4 1/2 15 1/8
6" FMT 10 3/4 — 19 3/4 — 5 1/2 22
VALVE A B C D E F2" PH 9 1/16 11 9/32 2 29/32 4 1/4 4 1/4 3
3" PH 12 7/8 15 9/32 4 1/32 5 1/2 5 1/2 3 3/4
LPHV DIMENSIONS