pipe bending machine bm 16-30 - wequipswequips.com/img/fotos/maats/maatsbm1630_gb.pdf · pipe...
TRANSCRIPT
Pipe Bending Machine
AATS
BM 16-30
Engine output: 129 kW / 173 HP Operating weight: 22.250 kg 49,053 lbRange: 16” - 30”
Basic machine
2 BM1630
EngineDiesel engine Liebherr D934-L-A6, Emission regulations
according to 97/68/EG, 2004/26/EG stage IIIA and EPA/CARB Tier 3
Rating (ISO9249) 129 kW / 173 HP
Rating (SAE J1349) 127 kW / 170 HP
Rated speed 1.800 rpm
Displacement 7,0 l / 426 cu. In.
Design 4-cylinder-in-line engine, water cooled, turbo-charged, air-to-air intercooler
Injection system Direct injection, pump-line-nozzle system, electronic engine management
Engine lubrication Pressurised lube system, engine lubrication guaranteed for inclinations up to 45 degrees
Operating voltage 24 V
Alternator 80 A
Starter 5,4 kW
Batteries 2 x 110 Ah / 12V
Air cleaner Dual stage dry type with safety element, precleaner, service gauge at operator stand
Cooling system Combi radiator, comprising radiators for water, hydraulic fluid and charge air. Hydrostatic driven.
Refill capacitiesFuel tank 200 l
Cooling system 30 l
Engine oil with filters 29 l
Hydraulic oil tank 540 l
Noise emissionExterior sound pressure (2000/14/EC)
LpA = 72-86 dB(A) (distance @ 1 m.)
Hydraulic systemSystem Load sensing proportional pump flow control
Pump type Swash plate, variable displacement piston pump
Pump flow max. 297 l/min / 65.4 gpm
Pressure limitation 350 bar / 5,075 PSI
Control valve 5 segments, hydraulic actuated
Filter system Return filter with magnetic rod in the hydraulic tank
Control 5 hydraulic actuated levers for all functions
Hydraulic cylindersOutboard cylinder 2x Liebherr, 240 x 500
Inboard cylinder 2x Liebherr, 150 x 145
Wedge cylinder 1x Liebherr, 120 x 600
Clamp cylinder 1x Liebherr, 100 x 400
UndercarriageChains Lubricated, single grouser shoes; track chain
tensioning by bolts
Track links 28 (each side)
Track rollers/carrier rollers 2 / 1 (each side)
Track shoes standard 458 mm / 18”
Track shoes option 508 mm / 20”
WinchRated line pull 6.350 kg / 14,000 lbs
Gearing Wormgear
Gear ratio 48 : 1
Maximum oil pressure 160 bar / 2320 PSI
Maximum oil flow 60 l/min / 16 gpm
Cable length 25 m / 82.02 ft
Cable diameter 13 mm / 0.51”
Bending dataMaximum wall thickness by grade at max. system pressure of 360 bar / 5240 PSI (based on 85% efficiency)
Pipe sizeInch / mm
X52Inch / mm
X60Inch / mm
X70Inch / mm
X80Inch / mm
X100Inch / mm
Radiusfeet / meter
Max. degree per 40 feet /12 meter joint
16 / 406 2.000 / 50,8 2.000 / 50,8 2.000 / 50,8 2.000 / 50,8 2.000 / 50,8 38 / 11,58 40,8
18 / 457 2.000 / 50,8 2.000 / 50,8 2.000 / 50,8 2.000 / 50,8 2.000 / 50,8 52 / 15,85 29,7
20 / 508 2.000 / 50,8 2.000 / 50,8 2.000 / 50,8 2.000 / 50,8 2.000 / 50,8 64 / 19,51 24,4
22 / 559 2.000 / 50,8 2.000 / 50,8 2.000 / 50,8 2.000 / 50,8 1.500 / 38,1 72 / 21,95 21,6
24 / 610 2.000 / 50,8 2.000 / 50,8 1.750 / 44,4 1.500 / 38,1 1.200 / 30,5 76 / 23,16 20,2
26 / 660 2.000 / 50,8 1.750 / 44,4 1.437 / 36,5 1.250 / 31,7 0.937 / 23,8 82 / 24,99 18,9
28 / 711 1.750 / 44,4 1.437 / 36,5 1.200 / 30,5 1.063 / 27,0 0.800 / 20,3 88 / 26,82 17,6
30 / 762 1.437 / 36,5 1.250 / 31,7 1.031 / 26,2 0.875 / 22,2 0.700 / 17,8 96 / 29,26 16,2
These figures are recommended only and do not constitute a warranty
All bends shown are based on the use of Maats bending mandrels and bending dies. The figures given are “average”, they will vary due to:- The wall thickness of the pipe- The actual (as opposed to the nominal) yield of the pipe- Skill of the operator in handling the bending machine and the mandrel- The origin of the pipe (pipe mill, plate mill, etc.) and quality of the pipe- The type of pipe, spiral seam pipe will normally accept 75% of the recommended bend- The type of die and or bending set being used (eg. polyurethane lining or special radius dies)
An unbent end (tangent) is produced at each end of the pipe where the pipe contacts the stiff back and the pin up. Normal unbent tangents are approx.16 feet / 5 meters.
BM1630 3
Dimensions and weights
DimensionsHeight over exhaust 2.676 mm / 8.77 ft
Overall length 7.509 mm / 24.63 ft
Width 2.615 mm / 9.57 ft
Max. shipping width 2.695 mm / 9.01 ft
Bending setsStandard sizes 16”, 18”, 20”, 22”, 24”, 26”, 28”, 30”
Special sizes are available on request
Standard sets are bare. Coated sets are available on request
WeightsOperating weight 22.250 kg / 49,053 lb
Weight bending set (avg.) 2.300 kg / 5,071 lb
7509
2676
2918
2747SHIPPING WIDTH
Equipment
Basic machineTowing lug front l
Battery compartment, lockable l
Cold start device l
Radiator guard l
Engine doors, hinged, lockable l
Lugs for crane lifting l
Fuel water separator l
Air filter, dry-type, dual step l
Toolkit l
Cyklon pre-filter +
Tier II engine +
Tier IV engine +
Electrical systemStarter motor 5,4 kW l
Working lights +
Battery main switch, mechanical l
On-board system 24 V l
Alternator 80 A l
Beacon l
Control and warning lightsHydraulic system pressure (analog) l
Engine RPM (digital) l
Machine hours (digital) l
% Engine load at current RPM (digital) l
Coolant temperature (digital) l
Oil pressure (digital) l
Fuel economy (digital) l
Active service codes (digital) l
UndercarriageTrack frame, closed l
Sprocket segments, bolted l
Tracks oil lubricated l
Track frame, rigid l
Track shoes 458 mm l
Track shoes 508 mm +
Special track sizes (width / length) +
WinchHigh torque motor l
Dual stage planetary differential gearing l
Load control valve l
Spring engaged freespooling clutch l
Cable 13 mm x 25 m l
Cable 13 mm x 35 m +
AttachmentsHydraulic PTO for mandrel l
Compressor for mandrel +
l = Standard, + = Option
Subject to change
4 BM1630
Doc
umen
tatio
n Te
chni
cal B
M16
30 E
nglis
h R
ev. 1
Options and / or special attachments, suppliedby vendors other than Maats, are only to beinstalled with the knowledge and approval ofMaats to retain warranty.
Maats Pipeline EquipmentBreukersweg 4 / P.O.Box 165, 7470 AD Goor (The Netherlands)Tel: +31 (0) 547-260000, Fax: +31 (0) 547-261000www.maats.com, E-mail: [email protected]