physics subject area test
DESCRIPTION
Physics Subject Area Test. ELECTRICITY & MAGNETISM. Electric Charge and Electrical Forces:. Electrons have a negative electrical charge . Protons have a positive electrical charge. These charges interact to create an electrical force . Like charges produce repulsive forces - PowerPoint PPT PresentationTRANSCRIPT
Physics Subject Area Test
ELECTRICITY & MAGNETISM
*Electrons have a negative electrical charge.
*Protons have a positive electrical charge.
*These charges interact to create an electrical force.*Like charges produce repulsive forces
–they repel each other*Unlike charges produce attractive forces
–they attract each other
Electric Charge and Electrical Forces:
* A very highly simplified model of an atom has most of the mass in a small, dense center called the nucleus.
The nucleus has positively charged protons and neutral neutrons.
Negatively charged electrons move around the nucleus at much greater distance.
Ordinary atoms are neutral because there is a balance between the number of positively charged protons and negatively charged electrons.
Electrostatic Charge:
*Electrons move from atom to atom to create ions.
*positively charge ions result from the loss of electrons and are called cations.
*Negatively charge ions result from the gain of electrons and are called anions.
(A)A neutral atom has no net charge because the numbers of electrons and protons are balanced.
(B) Removing an electron produces a net positive charge; the charged atom is called a positive ion (cation).
(C) The addition of an electron produces a net negative charge and a negative ion (anion).
The charge on an ion is called an electrostatic charge.
*An object becomes electrostatically charged by*Friction, which transfers electrons between two objects in contact,*Contact with a charged body which results in the transfer of electrons,*Induction which produces a charge redistribution of electrons in a material.
Electrical conductors are materials that can move electrons easily.*Good conductors include metals. Copper is the best
electrical conductor.
Electrical Conductors and Insulators
Electrical nonconductors (insulators) are materials that do not move electrons easily.Examples are wood, rubber etc.
Semiconductors are materials that sometimes behave as conductors and sometimes behave as insulators. Examples are silicon, arsenic, germanium.
fundamental charge - the electrical charge on an electron
-has a magnitude of 1.6021892 X 10-19 C (measured in coulombs).
coulomb - the charge resulting from the transfer of 6.24 x 1018 of the charge carried by an electron.
magnitude of an electrical charge (Q) is dependent upon how many electrons (n) have been moved to it or away from it.Mathematically,
Q = n e-
where e- is the fundamental charge.
Coulomb’s law: Electrical force is proportional to the product of the electrical charge and inversely proportional to the square of the distance.
This is known as Coulomb’s law.
where, *F is the force,*k is a constant and has the value of 9.00 x 109 Newtonmeters2/coulomb2 (9.00 x 10 9 Nm2/C2),*q1 represents the electrical charge of object 1 and q2 represents the electrical charge of object 2, and*d is the distance between the two objects.
221
dqq
kF
Force Fields: The electrical charge produces a force field, that is called an electrical field since it is produced by electrical charge.
Voltage is a measure of the potential difference between two places in a circuit.
*Voltage is measured in joules/coloumb.
*The rate at which an electrical current (I) flows is the charge (Q) that moves through a cross section of a conductor in a give unit of time (t),
I = Q/t.
*the units of current are coulombs/second.
*A coulomb/second is an ampere (amp).
ELECTRICAL CIRCUITS
The CELLThe cell stores chemical energy and transfers
it to electrical energy when a circuit is
connected. When two or more cells are connected together we call this a Battery.
The cells chemical energy is used up pushing a current round a circuit.
What is an electric current?An electric current is a flow of microscopic particles called
electrons flowing through wires and components.
+ -
In which direction does the current flow? from the Negative terminal to the Positive terminal of a cell.
*Simple Circuits*A simple circuit is a connection of batteries and
resistors that meets 2 criteria
1. All batteries are in series2. The equivalent resistance of the entire circuit can
be obtained by repeated use of just the series and parallel equivalent resistance formulas
simple circuitsHere is a simple electric circuit. It has a cell, a lamp and a switch.
To make the circuit, these components are connected together with metal connecting wires.
cell
lamp
switch
wires
simple circuitsWhen the switch is closed, the lamp lights up. This is because there is a continuous path of metal for the electric current to flow around.
If there were any breaks in the circuit, the current could not flow.
circuit diagram
cell switch
lamp
wires
Scientists usually draw electric circuits using symbols;
circuit diagramsIn circuit diagrams components are represented by the following symbols;
cell battery
switch
lamp
motorammeter
voltmeter
buzzer
resistor
variable resistor
types of circuitThere are two types of electrical circuits;
SERIES CIRCUITS PARALLEL CIRCUITS
The components are connected end-to-end, one after the other. They make a simple loop for the current to flow round.
SERIES CIRCUITS
If one bulb ‘blows’ it breaks the whole circuit and all the bulbs go out.
PARALLEL CIRCUITS
The current has a choice of routes.The components are connected side by side.
If one bulb ‘blows’ there is still be a complete circuit to the other bulb so it stays alight.
measuring current
Electric current is measured in amps (A)
using an ammeter connected in series in
the circuit.
A
measuring current
A A
This is how we draw an ammeter in a circuit.
SERIES CIRCUIT PARALLEL CIRCUIT
measuring currentSERIES CIRCUIT
PARALLEL CIRCUIT
• current is the same
at all points in the circuit.
2A 2A
2A
• current is shared
between the components
2A2A
1A
1A
copy the following circuits and fill in the missing ammeter readings.
?
?
4A
4A
4A
3A?
?
1A
?
3A
1A
1A
measuring voltageThe ‘electrical push’ which the cell gives to the current is called the voltage. It is measured in volts (V) on a voltmeter
V
Different cells produce different voltages. The bigger the voltage supplied by the cell, the bigger the current.
measuring voltage
Unlike an ammeter a voltmeter is connected across the components
Scientist usually use the term Potential Difference (pd) when they talk about voltage.
measuring voltage
V
This is how we draw a voltmeter in a circuit.
SERIES CIRCUIT PARALLEL CIRCUITV
V
measuring voltage
VV
V
series circuit
1.5V
• voltage is shared between the components
1.5V
3V
• voltage is the same in all parts of the circuit.
3V
parallel circuit
3V
3V
measuring current & voltage
copy the following circuits on the next two slides.
complete the missing current and voltage readings.
remember the rules for current and voltage in series and parallel circuits.
measuring current & voltage
V V
6V4A
A
A
a)
measuring current & voltage
V
V
6V4A A
A
A
b)
answers
3V 3V
6V
4A 4A6V
6V
6V4A 4A
2A
2A
4A
a) b)
*Electric CircuitsIn electricity, the concept of voltage will be like pressure. Water flows from high pressure to low pressure (this is consistent with our previous analogy that Voltage is like height since DP = rgh for fluids) ; electricity flows from high voltage to low voltage.
But what flows in electricity? Charges!How do we measure this flow? By Current:
current = I = Dq / DtUNITS: Amp(ere) = Coulomb / second
The rate at which electrons move along field lines is called drift speed, typically about 10-4 m/s
Electric current defined in terms of the flow of positive charge opposite the electrons is called conventional currentCurrent will always be in the same direction as the local electric field
Voltage Sources:batteries and
power suppliesA battery or power supply supplies voltage. This is analogous to what a pump does in a water system.
Question: Does a water pump supply water? If you bought a water pump, and then plugged it in (without any other connections), would water come out of the pump?
Question: Does the battery or power supply actually supply the charges that will flow through the circuit?
*Charges move from higher to lower potential*For the process to continue, charges that have moved from a higher to lower potential must be raised back to a higher potential again*A battery is able to add charges and raise the charges to higher electric potentialSymbol for a battery
*Voltage Sources:batteries and
power suppliesJust like a water pump only pushes water (gives energy to the water by raising the pressure of the water), so the voltage source only pushes the charges (gives energy to the charges by raising the voltage of the charges).
Just like a pump needs water coming into it in order to pump water out, so the voltage source needs charges coming into it (into the negative terminal) in order to “pump” them out (of the positive terminal).
*Voltage Sources:batteries and power
supplies
Because of the “pumping” nature of voltage sources, we need to have a complete circuit before we have a current.
Circuit Elements
two of the common circuit elements:capacitorresistor
The capacitor is an element that stores charge for use later (like a water tower).
The resistor is an element that “resists” the flow of electricity.
Electrical Resistance &
Ohms’ LawThe current established is directly proportional to the
voltage differenceOhm’s Law: ΔV ∝ I
In a plot of ΔV vs I, the slope is called the electrical resistance
Resistance
Current is somewhat like fluid flow. Recall that it took a pressure difference to make the fluid flow due to the viscosity of the fluid and the size (area and length) of the pipe. So to in electricity, it takes a voltage difference to make electric current flow due to the resistance in the circuit.
ResistanceBy experiment we find that if we increase the
voltage, we increase the current: V is proportional to I. The constant of proportionality we call the resistance, R:
V = I*R Ohm’s Law
UNITS: R = V/I so Ohm = Volt / Amp.
The symbol for resistance is
ResistanceJust as with fluid flow, the amount of resistance does not depend on the voltage (pressure) or the current (volume flow). The formula V=IR relates voltage to current. If you double the voltage, you will double the current, not change the resistance. The same applied to capacitance: the capacitance did not depend on the charge and voltage - the capacitance related the two.
As was the case in fluid flow and capacitance, the amount of resistance depends on the materials and shapes of the wires.
ResistanceThe resistance depends on material and geometry
(shape). For a wire, we have:R = r L / A
where r is called the resistivity (in Ohm-m) and measures how hard it is for current to flow through the material, L is the length of the wire, and A is the cross-sectional area of the wire. The second lab experiment deals with Ohm’s Law and the above equation.
*Electrical Power
The electrical potential energy of a charge is:U = q*V .
Power is the change in energy with respect to time:Power = DU / Dt .
Putting these two concepts together we have:Power = D(qV) / Dt = V(Dq) / Dt = I*V.
Electrical PowerBesides this basic equation for power:
P = I*Vremember we also have Ohm’s Law:
V = I*R .Thus we can write the following equations for power:P = I2*R = V2/R = I*V .To see which one gives the most insight, we need to
understand what is being held constant.
Electrical Power and Electrical Work:All electrical circuits have three parts in common.
*A voltage source.
*An electrical device
*Conducting wires.
The work done (W) by a voltage source is equal to the work done by the electrical field in an electrical device,
Work = Power x Time.
electrical work is measured in joules
A joule/second is a unit of power called the watt.
Power = current x potential
Or, P = I V
*Example
When using batteries, the battery keeps the voltage constant. Each D cell battery supplies 1.5 volts, so four D cell batteries in series (one after the other) will supply a constant 6 volts.
When used with four D cell batteries, a light bulb is designed to use 5 Watts of power. What is the resistance of the light bulb?
*ExampleWe know V = 6 volts, and P = 5 Watts; we’re
looking for R.We have two equations:
P = I*V and V = I*Rwhich together have 4 quantities:
P, I, V & R..We know two of these (P & V), so we should be able
to solve for the other two.
*Example
Using the power equation we can solve for I:P = I*V, so 5 Watts = I * (6 volts), orI = 5 Watts / 6 volts = 0.833 amps.
Now we can use Ohm’s Law to solve for R:V = I*R, so
R = V/I = 6 volts / 0.833 amps = 7.2 W .
*Example extendedIf we wanted a higher power light bulb, should we have a bigger resistance or a smaller resistance for the light bulb?
We have two relations for power that involve resistance:
P=I*V; V=I*R; eliminating V gives: P = I2*R and
P=I*V; I=V/R; eliminating I gives: P = V2 / R .In the first case, Power goes up as R goes up; in the second case, Power goes down as R goes up.
Which one do we use to answer the above question?
*Example extendedAnswer: In this case, the voltage is being held constant due to the nature of the batteries. This means that the current will change as we change the resistance. Thus, the
P = V2 / R would be the most straight-forward equation to use. This means that as R goes down, P goes up. (If we had used the P = I2*R formula, as R goes up, I would decrease – so it would not be clear what happened to power.)
The answer: for more power, lower the resistance. This will allow more current to flow at the same voltage, and hence allow more power!
*Kirchhoff’s Laws
*Junction Law: at a junction in a circuit, the sum of the current entering the junction will equal the sum of the current leaving.
Σ I = Σ I in out
*Loop Law: the sum of the potential drops around any closed loop must add to
Σ V = 0 loop
*Connecting ResistorsThere are two basic ways of connecting two resistors:
series and parallel.In series, we connect resistors together like railroad
cars; this is just like we have for capacitors:
+ - + -
high V low V R1 R2
*Formula for Series:
To see how resistors combine to give an effective resistance when in series, we can look either at
V = I*R,or at R = rL/A .
Vbat
R1
R2+
-
I
V1 V2
*Formula for SeriesUsing V = I*R, we see that in series the current
must move through both resistors. (Think of water flowing down two water falls in series.) Thus Itotal = I1 = I2 .
Also, the voltage drop across the two resistors add to give the total voltage drop:
(The total height that the water fell is the addition of the two heights of the falls.)
Vtotal = (V1 + V2). Thus, Reff = Vtotal / Itotal = (V1 + V2)/Itotal = V1/I1 + V2/I2 = R1 + R2.
*Formula for SeriesUsing R = rL/A , we see that we have to go over
both lengths, so the lengths should add. The distances are in the numerator, and so the values should add.
This is just like in R = V/I (from V = IR) where the V’s add and are in the numerator!
Note: this is the opposite of capacitors when connected in series! Recall that C = Q/V, where V is in the denominator!
*Formula for Parallel Resistors
The result for the effective resistance for a parallel connection is different, but we can start from the same two places:
(Think of water in a river that splits with some water flowing over one fall and the rest falling over the other but all the water ending up joining back together again.) V=I*R, or R = rL/A .
+
-
Vbat R1
R2
Itotal
I1 I2
*Formula for Parallel Resistors
V=I*R, or R = rL/AFor parallel, both resistors are across the same voltage, so Vtotal = V1 = V2 . The current can go through either resistor, so: Itotal = (I1 + I2 ) .
Since the I’s are in the denominator, we have:
R = Vtotal/Itotal = Vtotal/(I1+I2); or 1/Reff = (I1+I2)/Vtotal = I1/V1 + I2/V2 = 1/R1 + 1/R2.
Formula for Parallel Resistors
If we start from R = rL/A , we can see that parallel resistors are equivalent to one resistor with more Area. But A is in the denominator (just like I was in the previous slide), so we need to add the inverses:
1/Reff = 1/R1 + 1/R2 .
*Terminal Voltage
Terminal voltage, VT , is the potential difference between the terminals of a battery.
Ideal voltage, VB , is determined by the chemistry of the battery.
Internal resistance, ir : some charge will be los due to the random thermal motion of the battery
Terminal voltage will be: VT = VB - ir
For recharging a battery: VT = VB + ir
*Current DivisionWhen current enters a junction, Kirchhoff’s first law tells
you the sum of the current entering must equal the sum of the current leaving.
Example:
8 = I + 4I + 5I I = 0.8 A
1/RP = 1/20 +1/5 +1/4 = ½ RP = 2Ω
V = IRP = 8 • 2 = 16V
16 = I1(20) I1 = 0.8A16 = I2(5) I2 = 3.2A16 = I3(4) I3 = 4A
VB = 60 – 18 = 42V 1/RP = 1/12 + 1/6 = ¼ RP = 4Ω
Requiv = 4 + 8 + 6 + 3 = 21Ω 42 – I(21) = 0 I = 2A
VT60 = 60 – 2 • 1 = 58V
VT18 = 18 – 2 • 2 = 22V
2 = I + 2I I = 0.67A
*CapacitanceWe define capacitance as the amount of charge
stored per volt: C = Qstored / DV.UNITS: Farad = Coulomb / VoltJust as the capacity of a water tower depends on the
size and shape, so the capacitance of a capacitor depends on its size and shape. Just as a big water tower can contain more water per foot (or per unit pressure), so a big capacitor can store more charge per volt.
*Parallel Plate CapacitorFor a parallel plate capacitor, we can pull charge
from one plate (leaving a -Q on that plate) and deposit it on the other plate (leaving a +Q on that plate). Because of the charge separation, we have a voltage difference between the plates, DV. The harder we pull (the more voltage across the two plates), the more charge we pull: C = Q /DV. Note that C is NOT CHANGED by either Q or DV; C relates Q and DV!
*Capacitance*What happens when a water tower is over-filled? It
can break due to the pressure of the water pushing on the walls.*What happens when an electric capacitor is “over-
filled” or equivalently a higher voltage is placed across the capacitor than the listed maximum voltage? It will “break” by having the charge “escape”. This escaping charge is like lightning - a spark that usually destroys the capacitor.
*V or DV ?When we deal with height, h, we usually refer to the
change in height, Dh, between the base and the top. Sometimes we do refer to the height as measured from some reference point. It is usually clear from the context whether h refers to an actual h or a Dh.
With voltage, the same thing applies. We often just use V to really mean DV. You should be able to determine whether we really mean V or DV when we say V.
*Parallel Plate CapacitorFor this parallel plate capacitor, the capacitance is
related to charge and voltage (C = Q/V), but the actual capacitance depends on the size and shape: C plate ∝ A / d
A is the area of each plate, d is the distance between the plates
*Energy StorageIf a capacitor stores charge and carries voltage, it
also stores the energy it took to separate the charge. The formula for this is:
Estored = (1/2)QV = (1/2)CV2 ,where in the second equation we have used the
relation: C = Q/V .
*Energy Storage
Note that previously we had:U = q*V ,
and now for a capacitor we have:Ucap = ½ QV = ½ CV2 = ½ Q2/C
*Energy StorageThe reason is that in charging a capacitor, the first bit
of charge is transferred while there is very little voltage on the capacitor (recall that the charge separation creates the voltage!). Only the last bit of charge is moved across the full voltage. Thus, on average, the full charge moves across only half the voltage!
*Hooking Capacitors
TogetherInstead of making and storing all sizes of capacitors,
we can make and store just certain values of capacitors. When we need a non-standard size capacitor, we can make it by hooking two or more standard size capacitors together to make an effective capacitor of the value we need.
*Two basic ways
There are two basic ways of connecting two capacitors: series and parallel.
In series, we connect capacitors together like railroad cars; using parallel plate capacitors it would look like this:
+ - + -
high V low V C1 C2
*SeriesIf we include a battery as the voltage source, the series circuit would look like this:
C1
+ Vbat
C2
Note that there is only one way around the circuit, and you have to jump BOTH capacitors in making the circuit - no choice!
*Parallel
In a parallel hook-up, there is a branch point that allows you to complete the circuit by jumping over either one capacitor or the other: you have a choice!
High V C1 Low V
C2
*Parallel Circuit
If we include a battery, the parallel circuit would look like this:
+ + +Vbat C1 C2
*Formula for Series:
To see how capacitors combine to give an effective capacitance when in series, we can look either at C = Q/V, or at C plate = A /d
*Formula for Series
Using C = Q/V, we see that in series the charge moved from capacitor 2’s negative plate must be moved through the battery to capacitor 1’s positive plate.
C1
+ +QVbat C2
- -Q ( +Qtotal)
*Formula for SeriesBut the positive charge on the left plate of C1 will attract a negative charge on the right plate, and the negative charge on the bottom plate of C2 will attract a positive charge on the top plate - just what is needed to give the negative charge on the right plate of C1. Thus Qtotal = Q1 = Q2 .
C1 (+Q1 ) + +Q1 -Q 1 +Q2
Vbat C2
- -Q2
( +Qtotal)
*Formula for Series
Also, the voltage drop across the two capacitors add to give the total voltage drop:
Vtotal = (V1 + V2). Thus, Ceff = Qtotal / Vtotal = Qtotal / (V1 + V2), or
(with Qtotal = Q1 = Q2)[1/Ceff] = (V1 + V2) / Qtotal = V1/Q1 + V2/Q2
=
1/C1 + 1/C2 = 1/Ceffective
*Parallel CircuitFor parallel, both plates are across the same voltage, so Vtotal = V1 = V2 . The charge can accumulate on either plate, so:
Qtotal = (Q1 + Q2). Since the Q’s are in the numerator, we have:
Ceff = C1 + C2.
+ +Q1 +Q2
Vbat C1 -Q1 C2 -Q2
+Q1
+Qtotal = (Q1+Q2) +Q2
Review of FormulasElectric Current I= ΔQ/Δt Resistor Voltage Drop V = IRResistivity R = rL/AElectric Power P = IVResistance Power P = I2R = V2/RJunction Law SI = SI in outLoop Law SΔV = 0
loop Series Resistors Rs = R1 + R2 +…Parallel Resistors 1/RP = 1/R1 + 1/R2 +…Terminal Voltage VT = VB ± IRCapacitance C = Q/VParallel Plate Capacitor C plate ∝ A / dCapacitors in Series 1/Cs = 1/C1 + 1/C2 +…Capacitors in Parallel CP = C1 + C2 +…Energy in Capacitor U = ½ Q2 /C = ½ CV2 = ½ QV
1/Ceff = 1/C1 + 1/C2 .For capacitors in PARALLEL we have:
Ceff = C1 + C2 .Note that adding in series gives Ceff being smaller than the smallest,
while adding in parallel gives Ceff being larger than the largest!
Magnetism
Magnetic Fields:A magnet that is moved in space near a second magnet experiences a magnetic field.
A magnetic field can be represented by field lines.
The strength of the magnetic field is greater where the lines are closer together and weaker where they are farther apart.
Electric Currents and
Magnetism
Oersted discovered that a compass needle below a wire
(A) pointed north when there was not a current,
(B) moved at right angles when a current flowed one way, and
(C) moved at right angles in the opposite direction when the current was reversed.
A magnetic compass shows the presence and direction of the magnetic field around a straight length of current-carrying wire.
When a current is run through a cylindrical coil of wire, a solenoid, it produces a magnetic field like the magnetic field of a bar magnet. The solenoid is known as electromagnet.
Electric Meters:
*The strength of the magnetic field produced by an electromagnet is proportional to the electric current in the electromagnet.
*A galvanometer measures electrical current by measuring the magnetic field.
*A galvanometer can measure current, potential difference, and resistance.
Electric Motors:*An electrical motor is an electromagnetic device that converts electrical energy into mechanical energy.
*A motor has two working parts - a stationary magnet called a field magnet and a cylindrical, movable electromagnet called an armature.
*The armature is on an axle and rotates in the magnetic field of the field magnet.
*The axle is used to do work.