pg5_us

PIPE BEARING AND SADDLE COMPONENTS

PRODUCT GROUP

5

Roller bearings, type 51 to 53______________________________________ 5.1

Cylinder roller bearings, type 51 .. 19 ______________________________ 5.3

Double taper roller bearings, single, type 52 .. 19 ____________________ 5.3

Double taper roller bearings, movable, type 52 .. 29 __________________ 5.3

Double cylinder roller bearings, type 53 .. 19 ________________________ 5.4

Double cylinder roller bearings, type 53 .. 29 ________________________ 5.4

Pipe saddle for welding on, type 54 .. 19____________________________ 5.5

Pipe saddle with pipe clamp, type 54 .. 29 __________________________ 5.5

Support tray with pipe clamp, type 54 .. 39__________________________ 5.6

Lift-off restraint, type 55 .. 19 ______________________________________ 5.6

Insulated pipe supports, type 56 __________________________________ 5.7

Cold block pipe supports, type 56 ________________________________ 5.10

Weld-on pipe shoes, type 57 .. 11 and 57 .. 12 ____________________ 5.11

Stanchions for horizontal pipes, type 58 ..1. and 58 .. 2.______________ 5.12

Stanchions for short radius elbows

(R� OD), type 58 .. 1. and 58 .. 2. ________________________________ 5.13

Stanchions for long radius elbows

(R� 1.5OD), type 58 .. 1. and 58 .. 2. ______________________________ 5.14

Stanchions, type 58 ____________________________________________ 5.15

Elbow pads, type 58 .. 3. ________________________________________ 5.15

0

1

2

3

4

6

7

8

9

PRODUCTGROUP

5.0

PIPE BEARINGS AND SADDLE COMPONENTS

CONTENTS PAGE

5

5

0

1

2

3

4

6

7

8

9

http://www.lisega.com/pdf/pg0_us.pdf









5.1

ROLLER BEARINGSTYPE 51 TO 53

LISEGA – Standard Roller Bearings & Pipe SaddlesThese items are standardized in LISEGAProduct Group 5 for a wide range of applic-ations.

For applications outside the standard range,special designs can be offered.

Specification and design of roller bearingsIn the design of standard components, prac-tical requirements find special consideration.

The standard roller bearing is hot-dip galvan-ized and provides optimum corrosion protec-tion. Except for the movable double cylinderroller bearing Type 53 .. 29, weldings havebeen dispensed with.

The bearing axles are made from austeniticmaterial and have a polished surface. The slide bearings incorporate bushings madefrom a Teflon bronze sintered compound mat-erial fitted into the roller. The bearings aremaintenance free and guarantee dry runningqualities. The formed shoulder of each bushingminimizes the stick-slip drag effect on lateralloading. The bearing axles are permanentlyfixed in the middle section of the base. Spec-ial locking on the side bracket is not required.

The rollers are made from high tensile carbonsteel. Their outer surfaces are machined.

To compensate for misaligned anchor bolts,on site, the base holes are slotted for addi-tional adjustment.

The height dimensions (E) within a load grouprange are identical for all roller bearings, inc-luding the lateral movement type.

Information regarding material codes, stan-dards, calculations and weldings are givenin the Technical Specification on page 0.9and 0.10

Manufacture and StoringFor frequently used items, efficient serial prod-uction and stocking can be achieved throughstandardization.

Modern order logistics is possible through asingle fabrication process or in small lots,thus ensuring short fabrication and deliverytimes.

Technical Data for Roller Bearings

➜ rolling resistance of the rollers max 4%

➜ rolling resistance on lateral movement max 4%

➜ temperature range at nominal load -22°F to 176°F [-30°C to 80°C]

➜ permissible lateral loading 35% of nominal load

➜ permissible lift-off load 10% of nominal load

Piping systems arrangedhorizontally over longstretches are placed onsupports. To allow normalthermal movement, thesupport points are designedas either sliding or rollertypes.

For larger diameter pipingand especially when fluidsand insulation produce highloads, roller bearings prov-ide the optimum solution.

5

5.2

INSTALLATION INSTRUCTIONS

Roller BearingsThe roller bearings can be fixed by simplebolt connections or welded to the contactsurface of the pipe support. In each case thecomplete width of the base plate must besupported and secured.

Due to the slotted holes, roller bearings caneasily be adjusted even with slightly misal-igned anchor bolts.

Pipe SaddlesWelded pipe saddles are supplied coated witha weldable primer (1.18 mil [30µm]) (seeTechnical Specification page 0.10).

Care must be taken that the specified min-imum weld size is applied.

Pipe saddles with clamps are supplied readyto install.

Care must be taken to ensure the correct pos-itioning and adequate presetting of the bolts.

Lift-off restraintsWhen installing the lift-off restraint plate, caremust be taken to ensure that the gap bet-ween plate and roller is sufficient for normalmovement along the whole travel range.

The special design and quality of man-ufacture provide the following applicationbenefits:

➜ maintenance of minimum roll resistance (max 4%)

➜ takeover of realistic lateral loading for double taper and double cylinder roller bearings (35% of the support load)

➜ whole support load can be carried by just one roller of the double cylinder type

➜ absorption of lateral displacements bysideways sliding designs

➜ simple and safe design of lift-off restraints

➜ use of pipe saddles enables favorable load transfer into the pipe wall

➜ design of pipe saddles minimizes heat transfer

➜ hot dip galvanized corrosion protection for all roller bearings

➜ maintenance free operation

➜ stainless steel roller axle

➜ Teflon bronze compound bushes

➜ large range of sizes (OD 23/8 inch – OD 53 inch [OD 60mm – OD 1350mm])

➜ large load range (max support load 27 kips [120kN])

➜ short support height (see selection chart for E dimension)

5.3

Type

51 08 1951 16 1951 35 19

A1 A2 B E F G a b sWeight

(lbs)Load FN

(lbs x 1000)

Single cylinder roller bearingtype 51 08 19 to 51 35 19

Order details:Type 51 .. 19

Double taper roller bearing(single)type 52 04 19 to 52 35 19

� E = 1.064 · R +x


AR B C F G a b s xWeight

(lbs)E�

min. max.

Load FN

(lbs x 1000)Type

52 04 1952 08 1952 16 1952 35 19

�

AR B C F G a b s xWeight

(lbs)E�

min. max.

Load FN

(lbs x 1000)Type

52 04 2952 08 2952 16 2952 35 29

�

Double taper roller bearing (sideways movable)type 52 04 29 to 52 35 29

� E = 1.064 · R +x


1.83.67.9

31/243/453/4

23/437/843/4

31/837/851/8

223/833/8

13/821/823/8

23/8333/4

13/1615/16

1

3/81/29/16

3/161/43/8

2.65.2

12.2

0.91.83.67.9

41/853/861/29

31/237/843/461/4

23/433/837/853/8

21/8331/251/8

23/4331/243/4

13/1613/1615/16

1

3/83/81/29/16

3/161/45/161/2

21/821/227/84

4.07.2

12.030.8

31/4 61/46 871/2 97/893/4 135/8

11/8 - 37/831/4 - 51/843/8 - 61/253/8 - 9

0.91.83.67.9

61/871/481/211

31/237/843/461/4

23/433/837/853/8

41/843/451/271/8

23/4331/243/4

13/1613/1615/16

1

3/83/81/29/16

3/161/45/161/2

21/821/227/84

4.48.0

13.234.2

31/4 61/46 871/2 97/893/4 135/8

11/8 - 37/831/4 - 51/843/8 - 61/253/8 - 9

travel 2 inch

5

5.4

Order details:Type 53 .. 29with s = ...inch

A1R A2 B C F G a b s x Weight(lbs)

E�

min. max.

Load FN

(lbs x 1000)Type

53 08 1953 16 1953 35 1953 60 1953 12 19

AR B C Ød F G H tK xWeight

(lbs)E�

min. max.

Load FN

(lbs x 1000)Type

53 08 2953 16 2953 35 2953 60 2953 12 29

Double cylinder roller bearingtype 53 08 19 to 53 12 19

� E = 1.064 · R+x


1.83.67.9

13.527.0

81/4121/4161/2191/4243/8

71/2111/4145/8167/8205/8

31/837/851/857/871/8

21/231/243/853/861/2

51/2

9125/8145/8181/8

23/8331/237/841/2

13/1615/16

111/411/4

3/81/29/1611/167/8

3/161/43/81/2

11/16

15/813/421/821/223/4

5.612.230.850.8

105.8

27/8 91/253/8 143/491/2 201/2

13 241/4191/2 31

11/8 - 71/233/8 - 121/467/8 - 173/897/8 - 201/2

153/4 - 265/8

1.83.67.9

13.527.0

101/4133/4183/4207/8271/2

81/4113/4161/8181/425

2223/823/431/8

3/81/29/1611/167/8

53/461/481/297/8

123/8

61/271/495/8

113/8141/8

21/231/243/851/861/4

23/8337/843/453/4

1/41/41/43/83/8

15/813/421/821/223/4

13.222.050.877.2

154.0

11/8 - 71/233/8 - 121/467/8 - 173/897/8 - 201/2

153/4 - 265/8

27/8 9 1/253/8 143/491/2 201/2

13 241/4191/2 31

DOUBLE CYLINDER ROLLER BEARINGTYPE 53

A + travel s �

E�Double cylinder roller bearing (sideways movable)type 53 08 29 to 53 12 29

� E = 1.064 · R+x

� Travel s = 4…235/8inch

� Center fixing point from Travel s = 117/8inch

Weight at s = 4inch

5.5

WELD-ON PIPE SADDLESTYPE 54

Type

54 06 1954 08 1954 09 1954 11 1954 14 1954 17 1954 19 1954 22 1954 27 1954 32 1954 36 1954 41 1954 51 1954 61 1954 71 1954 81 19

OD Weight(lbs)

a sLoad FN

(lbs x 1000) �R

Type

54 06 2954 08 2954 09 2954 11 2954 14 2954 17 2954 19 2954 22 2954 27 2954 32 2954 36 2954 41 2954 51 2954 61 2954 71 2954 81 29

ODWeight

(lbs)BR

Load FN

(lbs x 1000) �s

Pipe saddle with pipe clamptype 54 06 29 to 54 81 29

� Load at pipe temperature 302°F.

Order details:Type 54 .. 29R = ...inch

Weld-on pipe saddletype 54 06 19 to 54 81 19

� Load at pipe temperature 302°F.

Order details:Type 54 .. 19R = ...inch

0.30.30.30.40.90.91.11.82.74.54.58.5

11.214.622.527.0

2.373.003.504.505.506.637.638.63

10.7512.7514.0016.0020.0024.0028.0032.00

31/8 - 71/831/2 - 71/233/4 - 75/843/8 - 81/443/4 - 85/853/8 - 91/457/8 - 97/861/4 - 101/471/2 - 113/881/2 - 123/89 - 13

10 - 14123/4 - 163/8143/4 - 181/4167/8 - 201/2187/8 - 221/2

3.0 - 7.83.4 - 8.23.4 - 8.43.4 - 8.84.4 - 11.06.6 - 14.46.6 - 15.08.8 - 17.6

14.8 - 29.821.2 - 39.622.0 - 39.628.6 - 55.222.0 - 35.226.4 - 46.235.2 - 57.441.8 - 72.8

3/163/163/163/163/163/163/161/41/41/41/45/165/165/163/83/8

1/81/81/81/83/163/163/161/43/81/21/29/163/81/29/16

13/16

0.30.30.30.40.90.91.11.82.74.54.58.5

11.214.622.527.0

2.373.003.504.505.506.637.638.63

10.7512.7514.0016.0020.0024.0028.0032.00

15/815/815/82222223/823/823/823/423/431/231/231/2

1/81/81/81/83/163/163/161/43/81/21/29/163/81/29/16

13/16

31/8 - 71/831/2 - 71/233/4 - 75/843/8 - 81/443/4 - 85/853/8 - 91/457/8 - 97/861/4 - 101/471/2 - 113/881/2 - 123/89 - 13

10 - 14123/4 - 163/8143/4 - 181/4167/8 - 201/2187/8 - 221/2

5.6 - 10.66.2 - 12.86.8 - 13.2

11.0 - 15.413.2 - 19.815.4 - 26.417.6 - 28.619.8 - 33.033.0 - 44.041.8 - 57.446.2 - 66.266.2 - 88.270.6 - 83.8

139.0 - 159.0165.0 - 190.0185.0 - 216.0

Up to

OD 16“

From

OD 20“

From

OD 20“

Up to

OD 16“

leg length

ODOD

OD OD

L=12

L=12

5

5.6

Type

54 06 3954 08 3954 09 3954 11 3954 14 3954 17 3954 19 3954 22 3954 27 3954 32 3954 36 3954 41 3954 51 3954 61 3954 71 3954 81 39

ODWeight

(lbs)Load FN

(lbs x 1000)sR

A B Rcompatible with

roller bearing, typeType

55 08 1955 16 1955 35 1955 60 1955 12 19

Pipe tray with pipe clampstype 54 06 39 to 54 81 39


Lift-off restrainttype 55 08 19 to 55 12 19

Order details:Type 55 .. 19for type 54 .. .9R = ...inch

0.20.20.30.40.90.91.21.82.33.44.57.99.0

13.518.022.5

2.373.003.504.505.506.637.638.63

10.7512.7514.0016.0020.0024.0028.0032.00

13/815/817/821/2331/2445/855/863/473/883/8

103/8121/2145/8165/8

1/81/83/163/163/163/163/161/41/45/163/83/83/81/29/169/16

3.54.55.5

10.512.013.014.516.524.531.035.553.061.5

123.0150.0165.0

53 08 1953 16 1953 35 1953 60 1953 12 19

87/813 1/417 7/822271/2

31/837/851/857/871/8

11/8 - 71/233/8 - 121/467/8 - 173/897/8 - 201/2

153/4 - 265/8

PIPE TRAY WITH PIPE CLAMPS TYPE 54 LIFT-OFF RESTRAINT TYPE 55

OD

OD

L=12�90˚

L=12

INSULATED PIPE SUPPORTSTYPE 56

5.7

Pipe Supports for Cryogenic ApplicationsLISEGA offer a complete range of insulatedpipe supports for all types of cryogenic pipingapplications. Typically, these include industrialprocesses involving the production, transpor-tation and distribution of liquefied gasesincluding methane, propane, butane (LNG),ethylene, oxygen, nitrogen and ammonia (LPG).

LISEGA standard insulated pipe supports aredesigned in accordance with recognized engin-eering specifications and international stan-dards for pipes ranging in size from OD 0.84inch [21.3mm] to OD 36 inch [914mm] withinsulation thicknesses from 1 inch [25mm]up to 10 inch [250mm]. The supports aremanufactured using materials suitable forthe loads specified and for temperaturesranging from ambient to –321°F [–196°C].

Insulation Material

The insulation material that forms an integralpart of the insulated pipe support assemblyis manufactured using fire-retarding high-density polyurethane (PUF) foam. For thesupply of the PUF components and consu-mables, LISEGA have formed an alliance with Bains HardingIndustries Pty. Ltd., Australia. With more thantwenty five years experience in industrialinsulation, the company has extensive experience in the manufacture of rigid polyurethane insulation materials includinghighdensity moulded products and provideconstruction and maintenance services tothe liquefied natural gas industry (LNG) inAustralia and South East Asia.

PUF ManufactureThe PUF is monolithically molded in heavyduty steel molds under carefully controlledtemperature and humidity conditions. Thisensures compliance with dimensional spec-ifications and provides clean, sharp edgesthat fit neatly with the adjacent line insul-ation material on site. Careful attention isgiven to the curing of the PUF after moldingto ensure dimensional stability.

Both single and multilayer PUF cradlesystems are manufactured in accordancewith ASTM C-585 and incorporate steppedradial and offset longitudinal joints. This pro-vides a reliable interlocking interface witheach layer of the adjacent line insulation onsite and prevents a direct vapor path to theinsulation surface.

All exposed PUF cradle surfaces are sealedwith cryogenic fire-retarding elastomeric vaporbarrier mastic to prevent moisture ingress.A laminated aluminum/polyester foil is bon-ded to the outermost surface of the PUFcradle assembly. This has an overlap allo-wance designed to cover the adjacent lineinsulation material on site. Finally, a sheetmetal jacket forms part of the PUF cradleassembly and fits over the aluminum/poly-ester foil to provide additional support andinsulation protection.

The PUF cradles are available in three stan-dard densities toprovide for varyingload requirements – 10 lbs/ft3 [160 kg/m3], 14 lbs/ft3 [224 kg/m3], 20 lbs/ft3 [320 kg/m3].

5.8

Density

Compressive strength

Linear coefficient of

expansion

Closed cell content

Thermal conductivity

Unit

lbs/ft3

lbs/inch2

1/°F

%

Btu inch/(HR ft2 °F)

68°F-265°F

68°F-265°F

ASTM D1622ASTM D1621

BS 4370

ASTM D2856ASTM C177

10

� 290� 533� 38.9x10-6

� 90

� 0.222� 0.146

14

� 580� 834� 38.9x10-6

� 90

� 0.243� 0.187

20

� 1015� 1777� 38.9x10-6

� 90

� 0.284� 0.236

Test standard

5Material properties of insulation

Steel Clamp BaseLISEGA standard insulated pipe supports aredesigned to clamp onto the pipe mechan-ically. The steel clamp base support that the PUFcradle assembly fits into is manufacturedfrom carbon steel and supplied with a hotdip galvanized finish as standard. Material grades, welding and surface treatmentare in accordance with the LISEGA standardspecifications shown on pages 0.9 and 0.10of the catalog.

The quality control system employed by LISEGAin the manufacture and assembly of pipesupports is described on page 0.15. The in-spection and test procedure includes a trialfitting of each pipe support to a suitablesection of pipe to ensure compliance withthe specification.

Type

88 06 3.88 07 3.88 09 3.88 11 3.

Nominal thickness of insulation (inch)

Thickness of layering (inch)

34567810

1.5 / 1.52 / 2

1 / 2 / 22 / 2 / 22 / 3 / 22 / 4 / 2

2 / 2 / 4 / 2

59.50 65.1071.9077.5083.1089.9095.50

107.90

56 .. 6.

Table of outer diameter D of the insulation (excluding sheet metal jacket)

Nominal insulation thickness

CRYOGENIC CLAMP BASES TYPE 56 .. 10 TO 56 .. 69

5.9

Cryogenic clamp basesType 56 01 10 to 56 91 69

Type

56 01 ..56 02 ..56 03 ..56 06 ..56 09 ..56 11 ..56 17 ..56 22 ..56 27 ..56 32 ..56 36 ..56 41 ..56 46 ..56 51 ..56 56 ..56 61 ..56 66 ..56 71 ..56 76 ..56 81 ..56 91 ..

OD

DWidth of theclamp base B

0.841.061.332.373.504.506.638.63

10.7512.7514.0016.0018.0020.0022.0024.0026.0028.0030.0032.0036.00

.. .. 1. Length C: 12; density of insulation 10 lb/ft3




2 3/4> 9>12>17 1/2>23 1/2>31 1/2

… 9… 12… 171/2… 231/2… 311/2

468

121620

Permissible load (lbs x 1000) at –275°F [-170°C] �

0.520.650.831.512.204.726.978.99

11.20 13.40 14.6016.8018.8021.1022.4024.70 26.9029.2031.4033.7037.00

56 .. 2.

1 11/2 2 3 4 5 6 7 8

6th digit of type designation

23/4331/443/851/261/285/8

105/8123/4

56 .. .0

441/441/251/265/875/893/4

113/4137/8157/8

56 .. .1

43/4551/461/471/283/8

101/2121/2145/8163/418

56 .. .2

71/873/875/885/893/4

103/4127/8147/81719203/8221/4

56 .. .3

83/487/891/4

101/4113/8123/8141/2161/2185/8205/8217/8237/8257/8277/8297/8317/8337/8357/8377/8397/8437/8

56 .. .4

111/4115/8125/8133/4143/4167/8187/82123241/4261/4281/4301/4321/4341/4361/4381/4401/4421/4461/4

56 .. .5

141/8153/8161/4183/8203/8221/2245/8257/8273/4293/4313/4337/8357/8373/4393/4413/4437/8473/4

56 .. .6

175/8185/8203/4223/4247/8267/8281/4301/8321/8341/8361/8381/4401/8421/8441/8461/8501/8

56 .. .7

201/4223/8243/8261/2281/2293/4313/4333/4353/4373/4393/4413/4433/4453/4473/4513/4

56 .. .8

10

241/8261/4281/4303/8321/2333/4355/8375/8395/8413/4433/4455/8475/8495/8513/4555/8

56 .. .9

0.520.650.831.512.202.704.055.406.748.098.77

10.10 11.2012.5013.9015.0016.4017.7018.8020.2022.40

56 .. 1.

23.60 26.9030.3033.7037.0040.4043.8047.2050.5053.9061.80

56 .. 4.5th digit of type designation

C minus 3/4

sheet metal jacket

OD

6

4

2

2

2

� 61/4

� Maximum lateral loading 30% of vertical load

Pipe Supports for Cryogenic ApplicationsLISEGA standard cold block supports are de-signed in accordance with recognized engin-eering specifications and international stand-ards for pipes ranging in size from OD 0.84inch [21.3mm] to OD 36 inch [914mm]. Thesupports are manufactured using materialsthat are suitable for the loads specified andtemperatures ranging from ambient to–321°F [–196°C].

Cold Block MaterialThe cold block insulation material formingan integral part of the cold block pipe supportassembly is designed to provide a sufficientthermal insulation barrier between the pipeoperating at subzero temperatures and thesupporting structure that is at ambient tem-perature.

LISEGA standard cold block supports incor-porate Lignostone® densified wood blocksthat are manufactured from selected beechveneers, impregnated under vacuum withthermosetting synthetic resin and densifiedunder heat and pressure. The Lignostone®

blocks combine high strength with low ther-mal conductivity, have proven cryogeniccapability and are used exclusively for coldpipe applications throughout the world.

Alternative cold block insulation materialssuitable for cryogenic applications are avail-able on request.

COLD BLOCK PIPE SUPPORTSTYPE 56 .. 91

5.10

Steel Clamp BasesLISEGA standard cold block pipe supports aredesigned to mechanically clamp onto the pipe.The steel clamp base support is manufacturedfrom stainless steel and is supplied self-coloras standard. The cold block is bolted betweenthe underside of the clamp base and a carbonsteel base plate. Material grades, welding andsurface treatment are in accordance with theLISEGA standard specifications.

Other pipe support configurations can be sup-plied (pipe support stanchions, cradles, anchors)on request.

LISEGA cold block pipe supports are suppliedwith detailed installation instructions. Each pipesupport is clearly marked in accordance withthe LISEGA Type Designation System.

LISEGA cold block pipe supports are suppliedfully assembled and packed to protect the fin-ished product from superficial damage and mois-ture ingress during storage and transportation.

+68

2.144

Temperature

Thermal

conductivity

-148

1.686

-292

1.422

-321

1.381

5

� permissible loads at cryogenic temperature

OD°F

Btu inch /

(HR ft2 °F)

J

A

Length=B

ODpermissible load(lbs x 1000) �

A B H E G

0.841.061.332.373.504.506.638.63

10.7512.7514.0016.0018.0020.0022.0024.0026.0028.0030.0032.0036.00

0.290.360.470.831.241.602.252.923.824.504.955.626.296.977.648.549.229.89

10.5711.2412.81

67/867/867/867/867/867/867/891/291/2

141/8141/8141/8161/8173/8191/4191/4231/4231/4231/4231/4271/8

77/877/877/877/877/877/877/877/877/8

153/4153/4153/4153/4153/4153/4153/4153/4153/4153/4153/4153/4

37/837/837/837/837/857/857/857/857/857/857/857/857/857/857/857/857/857/857/857/857/8

43/841/245/851/855/881/891/4

101/4111/4121/4127/8137/8147/8157/8167/8177/8187/8197/8207/8217/8237/8

27/831/831/445/851/271/483/4

101/8123/8137/8143/4171/4183/4203/4231/2251/4271/8291/8311/8331/4371/8

C

1 3/81 5/81 5/82 1/42 3/43 5/84 3/85 1/86 1/477 3/88 5/89 3/8

103/811 3/4125/8135/8145/8155/8165/8185/8

t

3/83/83/83/83/83/83/83/85/85/85/85/85/83/43/43/43/43/43/43/41

Type

56 01 9156 02 9156 03 9156 06 9156 09 9156 11 9156 17 9156 22 9156 27 9156 32 9156 36 9156 41 9156 46 9156 51 9156 56 9156 61 9156 66 9156 71 9156 76 9156 81 9156 91 91

J

53/853/853/853/853/853/853/877/877/8

125/8125/8125/8145/8153/4173/4173/4215/8215/8215/8215/8255/8

5.11

WELD-ON PIPE SHOESTYPE 57 .. 11 AND 57 .. 12

Weld-on pipe shoes madefrom T/C sectionFor use with small pipeloads and temperature � 175°F [80°C]

type 57 .. 11 to 57 .. 12

Material: carbon steel

Surface: primer

Type designation:57 .. 11 (T Shoe)57 .. 12 (C Shoe)

� Field weld – For the weldsize and permissible loadsspecified, the stress in theweld is less than 7.25 ksi [50 N/mm2].

Type

57 03 1157 03 1157 03 1157 03 1157 03 1157 07 1157 07 1157 07 1157 07 1157 13 1157 13 1157 13 1157 13 1157 13 1157 13 1157 24 1257 24 1257 24 1257 24 1257 24 1257 36 1257 36 1257 36 1257 42 1257 42 1257 42 1257 51 1257 51 1257 61 1257 61 12

Load F [lbsx1000] at 175°F

OD A B Ea �

leg length

Weight(lbs)

0.841.061.331.671.902.372.873.003.504.254.505.255.506.256.637.638.639.63

10.5010.7512.7514.0014.5016.0016.5018.0020.0022.0024.0026.00

0.220.220.220.220.220.340.340.340.340.450.450.450.450.450.451.351.351.351.351.351.802.252.252.252.252.703.373.374.504.50

444446666666666

101010101010101010101010101010

44444444444444444444666888

10101212

3/163/163/163/163/163/163/163/163/163/163/163/163/163/163/161/41/41/41/41/41/41/41/41/41/41/41/41/41/41/4

1.51.51.51.51.52.32.32.32.37.57.57.57.57.57.56.06.06.06.06.0

10.010.010.015.615.615.618.318.325.825.8

31/433/831/235/833/4441/443/845/861/861/465/863/471/871/451/853/461/463/467/881/487/891/4

101/8103/8103/4121/4133/8143/8151/2

Order details:Weld-on pipe shoetype 57 .. 1.

�

�

2 2

5

5.12

Order details:Type 58 24 21, E = 311/2inch

STANCHIONS FOR HORIZONTAL PIPESTYPE 58 .. 1. AND 58 .. 2.

E maxOD NStanchion

typeE minD x s a legType

58 05 .158 06 .158 06 .258 07 .158 07 .258 08 .158 08 .258 09 .158 09 .258 10 .158 10 .258 11 .158 11 .258 13 .158 13 .258 14 .158 14 .258 16 .158 16 .258 17 .158 17 .258 19 .158 19 .258 22 .158 22 .258 24 .158 24 .258 26 .158 26 .258 27 .158 27 .258 32 .158 32 .258 36 .158 36 .258 37 .158 37 .258 41 .158 41 .258 42 .158 42 .258 46 .158 46 .258 51 .158 51 .258 56 .158 56 .258 61 .158 66 .158 71 .158 76 .158 81 .158 91 .1

1.902.372.372.872.873.003.003.503.504.254.254.504.505.255.255.505.506.256.256.636.637.637.638.638.639.639.63

10.5010.5010.7510.7512.7512.7514.0014.0014.5014.5016.0016.0016.5016.5018.0018.0020.0020.0022.0022.0024.0026.0028.0030.0032.0036.00

1 sch 801 sch 80

1.5 sch 801 sch 80

1.5 sch 801 sch 80

1.5 sch 801 sch 80

1.5 sch 801.5 sch 802.5 sch 401.5 sch 802.5 sch 401.5 sch 802.5 sch 402.5 sch 40

3 sch 402.5 sch 40

3 sch 402.5 sch 40

3 sch 403 sch 404 sch 803 sch 404 sch 803 sch 404 sch 804 sch 805 sch 804 sch 805 sch 805 sch 808 sch 405 sch 808 sch 405 sch 808 sch 405 sch 808 sch 405 sch 808 sch 408 sch 40

12 sch 408 sch 40

12 sch 408 sch 40

12 sch 4012 sch 4012 sch 4012 sch 4012 sch 4012 sch 4012 sch 40

aababababbcbcbccdcdcddededeefeffgfgfgfgfgghghghhhhhhh

3/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/161/43/161/43/161/41/43/81/43/83/81/43/81/43/81/43/81/43/81/41/43/81/43/81/43/83/83/83/83/83/83/8

15/16

13/16

13/16

17/16

17/16

1 1/21 1/21 3/41 3/42 1/82 1/82 1/42 1/42 5/82 5/82 3/42 3/43 1/83 1/835/16

35/16

313/16

313/16

45/16

45/16

413/16

413/16

5 1/45 1/45 3/85 3/86 3/86 3/8777 1/47 1/4888 1/48 1/499

10101111121314151618

1010101010101010101010121212121212121212121212141414141414141416161616161618181818181820202020222224242628

4444444444444444444444444444444646464646464646464648484848484848485050505050505050525252525454545656585860

�

�

� ... � see page 5.15

Example: Telescopic stanchion for pipe OD = 9.63inch,E = 311/2inch (sliding)

The length of the stanchion is: L = E-N see data fromthe selection table L = 311/2 - 413/16 = 2611/16inch.

For stanchion D = 3sch40 (designation “d”)

Permissible load = 0.36 x 2470lbs (see tables on page 5.15) = 890lbs

Type 58 .. 112

Type 58 .. 212

OD

OD

5.13

STANCHIONS FOR SHORT RADIUS ELBOWS(R� OD) TYPE 58 .. 1. AND 58 .. 2.

E maxOD NStanchion

typeE minD x s a leg

Type

58 05 .358 06 .358 06 .458 07 .358 07 .458 08 .358 08 .458 09 .358 09 .458 10 .358 10 .458 11 .358 11 .458 13 .358 13 .458 14 .358 14 .458 16 .358 16 .458 17 .358 17 .458 19 .358 19 .458 22 .358 22 .458 24 .358 24 .458 26 .358 26 .458 27 .358 27 .458 32 .358 32 .458 36 .358 36 .458 37 .358 37 .458 41 .358 41 .458 42 .358 42 .458 46 .358 46 .458 51 .358 51 .458 56 .358 56 .458 61 .358 66 .358 71 .358 76 .358 81 .358 91 .3

Order details:Stanchions for short radius elbows R � OD type 58 42 23, E = 291/2inch

�

�

� ... � see page 5.15

Example: Stanchion for short radius elbow R � OD, OD = 161/2inch, E = 291/2inch (anchor)

Length of stanchion: L = E-N (see data from the selection table), L = 291/2 - 2 = 271/2inch.

For stanchion D = 5 sch 80 (designation “f”)


Type 58 .. 134

Type 58 .. 234

1.902.372.372.872.873.003.003.503.504.254.254.504.505.255.255.505.506.256.256.636.637.637.638.638.639.639.63

10.5010.5010.7510.7512.7512.7514.0014.0014.5014.5016.0016.0016.5016.5018.0018.0020.0020.0022.0022.0024.0026.0028.0030.0032.0036.00

1 sch 801 sch 80

1.5 sch 801 sch 80

1.5 sch 801 sch 80

1.5 sch 801 sch 80


3 sch 402.5 sch 40

3 sch 402.5 sch 40


12 sch 408 sch 40

12 sch 408 sch 40



3/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/161/43/161/43/161/41/43/81/43/83/81/43/81/43/81/43/81/43/81/41/43/81/43/81/43/83/83/83/83/83/83/8

1/21/21/21/21/25/85/85/85/85/85/83/43/43/43/47/87/87/87/8

11/811/811/411/413/813/813/813/815/815/815/815/817/817/815/815/813/413/417/817/82221/821/823/823/825/825/827/831/831/431/233/441/4

1010101010101010101010101010101010121212121212121212121212121214141414141414141414161616161616181818181820

4242424242424242424242444444444444444444444444444444444444444444444444444444444444444444444444464646464646

OD

OD

5.14

5

� ... � see page 5.15

Example: Stanchion for long radius elbow R � 1.5 OD,OD = 161/2inch, E = 291/2inch (anchor)

Length of stanchion: L = E+N (see data from the selec-tion table), L = 291/2 + 27/8 = 323/8inch.

For stanchion D = 5 sch 80 (designation “f”)


STANCHIONS FOR LONG RADIUS ELBOWS R� 1.5 OD, TYPE 58 .. 1. AND 58 .. 2.

EmaxOD NStanchion

typeEminD x s a leg

Order details:Stanchions for long radius elbows R � 1.5ODtype 58 42 25, E = 291/2inch

Type

58 05 .558 06 .558 06 .658 07 .558 07 .658 08 .558 08 .658 09 .558 09 .658 10 .558 10 .658 11 .558 11 .658 13 .558 13 .658 14 .558 14 .658 16 .558 16 .658 17 .558 17 .658 19 .558 19 .658 22 .558 22 .658 24 .558 24 .658 26 .558 26 .658 27 .558 27 .658 32 .558 32 .658 36 .558 36 .658 37 .558 37 .658 41 .558 41 .658 42 .558 42 .658 46 .558 46 .658 51 .558 51 .658 56 .558 56 .658 61 .558 66 .558 71 .558 76 .558 81 .558 91 .5

1.902.372.372.872.873.003.003.503.504.254.254.504.505.255.255.505.506.256.256.636.637.637.638.638.639.639.63

10.5010.5010.7510.7512.7512.7514.0014.0014.5014.5016.0016.0016.5016.5018.0018.0020.0020.0022.0022.0024.0026.0028.0030.0032.0036.00

1 sch 801 sch 80

1.5 sch 801 sch 80

1.5 sch 801 sch 80

1.5 sch 801 sch 80


3 sch 402.5 sch 40

3 sch 402.5 sch 40


12 sch 408 sch 40

12 sch 408 sch 40



3/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/163/161/43/161/43/161/41/43/81/43/83/81/43/81/43/81/43/81/43/81/41/43/81/43/81/43/83/83/83/83/83/83/8

01/81/81/81/81/81/81/81/81/41/43/83/81/21/21/21/25/85/85/85/87/87/8

111111/811/811/411/411/211/221/221/225/825/827/827/827/827/831/431/431/231/237/837/841/445/8553/855/863/8

810101010101010101010101010101010101010101010101010101010101012121010101010101212121212121414141616181820

4242424242424242424242424242424242424242424242424242424242424240404040404040404040404038383838383836363636

Type 58 .. 156

Type 58 .. 256

�

�

OD

5.15

Order details:Type 58 .. 3.

STANCHIONSTYPE 58

� Field weld

� For weld size and per-missible loads specified,stress in weld less than 7.25ksi [50 N/mm2]

� Type designation:

58 .. 1. Stanchion58 .. 2. Telescopic stanchion

� Permissible load foractual stanchion lengthtaken from chart

� Maximum lateral load is 100% of specified vertical load

Material: carbon steel

Surface: primer

Elbow pads for long radiuselbows (R�1.5OD)

Type 58 06 3. to 58 11 3.

� Field weld� 6th digit of type designation:

1 = Material: carbon steelSurface: primer

2 = Material: 1.4301 (stainless steel)

D x svertical

loadA x tsliding fixed

anchorType

abcdefgh

58 .. 1. 58 .. 2.

Max. permissible load at 175°F (lbs)

only

Weight (lbs)

for L= 8inch per add.

inch

Permissible load against length of sliding / fixed (anchor) stanchions.

Type

58 06 3.58 07 3.58 09 3.58 11 3.

OD A B tWeight

(lbs)

1 sch 801.5 sch 802.5 sch 40

3 sch 404 sch 805 sch 808 sch 40

12 sch 40

31/2 x 3/841/2 x 3/8

5 x 3/86 x 3/8

71/2 x 1/281/2 x 5/812 x 3/416 x 1

2130494076408990

17530215803372074180

420830

1770247056207860

1551041580

240510

11201590359050509770

25400

2.84.56.88.7

17.025.848.7

101.0

4.08.89.2

14.523.934.859.0

119.0

0.180.300.520.641.281.792.334.33

2.372.873.504.50

31/823/423/443/4

37/837/831/261/4

3/163/163/161/4

0.560.600.542.00

� �

( (

�

R�1.5OD

OD

L (inch)

pg5_us

Documents