PFT-60 SideLite Transom Patch w/Stop Installation Instructions

Copyright © 2017, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited.

For Installation Assistance, Call 855.594.6989 • www.assaabloyglass.us

PFT-60 - 06/17

Tools Needed: Torque Wrench and Bit5mm Hex Wrench

Parts Included

NOT TO SCALE

Top Panel

SidePanel

PFT-60

{ Stop Tab

z Cover Plate

w Bushings (3)

y Screws (3)

x Bracket

v Bracket

u Cover Plate

| Blank Tabs (4)

PFT-60 Parts List1 Cover Plate2 Bracket3 Bushings (3)4 Bracket5 1 1/16" - M6 x 27 Screws (3)6 Cover Plate7 Stop Tab — PF-INS0028 Blank Tabs (4)

4 3/16"(106) 4 3/16"

(106)

2 1/16"(52)

2 1/16"(52)

Copyright © 2017, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited. 2PFT-60 - 06/17

1.

2.

Prepare the Glass

Fasten Stop Tab• Gently pull back adhered gasket to remove blank tab & insert Stop Tab { onto

the appropriate bracket (v or x) depending on door configuration and swing.

DIAGRAM SHOWS BRACKET x APPLICATION ONLY.

Side Panel

Top Panel

2 7/8"(73)

1 3/8"(36)

1 3/8"(36)

1/8" (3)

1 3/8"(36)

1 3/8"(36)

Ø 13/16"(20)

Ø 13/16"(20)

Ø 13/16"(20)

x Bracket

{ Stop Tab

Caution: Office copiers, printers and facsimile machines may change the size of a drawing and make it inaccurate to use as a template.

USE FABRICATION SKETCH TO DRILL AND CUT GLASS.• Drill 13/16" (20 mm) diameter hole.

NOT TO SCALEDIMENSIONS IN INCHES (MILLIMETERS)

w Bushings (3)

y Screws (3)

x Bracket

v Bracket

3. Fasten Support BracketsMake sure the surface is thoroughly cleaned and remove all screws.• Insert the three Bushings w into prepped 13/16" (20 mm) diameter holes.• Place Bracket v into prepped area of glass, join Bracket x from the other side. Insert Screw y into Bracket x and tighten with 5 mm hex

wrench to hold Brackets together. Do not tighten completely to allow for adjustments throughout installation.• Insert two Screws y into Bracket v, align fitting to desired position. Torque both Screws to 12 nm. Then tighten Bracket x Screw to 12 nm.

Copyright © 2017, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited. 3PFT-60 - 06/17

4. Adhere Cover Plates• Remove adhesive strip paper on both Brackets v & x to adhere Cover Plates u & z.• Hook Cover Plates u & zover hinge side locking pins.• Push in spring loaded locking pin on opposite side of Bracket.• Snap on Cover Plates.

v Bracket

z Cover Plate

u Cover Plate

PFT-60 - 06/17Copyright © 2017, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited.

USA: ASSA ABLOY Glass SolutionsRockwood, PA 15557Phone: 855.594.6989

www.assaabloyglass.us