peak pourpdf anglais - · pdf filesurised hose or when a pressurised hose is ruptured, the...
TRANSCRIPT
P2
PPEEAAKK PPEERRFFOORRMMAANNCCEE
REDUCING
• Universal joint that improvestool manœuvrability, mini-mizes operator fatigue andextends hose life
• Swivels 360° at two pivotpoints, allowing the air hose todrop directly to the floor, whileproviding superb tool handling
RACCORDS PIVOTANTS MAXPRO
• Improves tool manoeuvrability and allows full360° at two pivot points
• Available with built-in UNIMAX 5 in 1 universalcoupler that accepts 1/4 INDUSTRIAL,ARO 210, 1/4 TRUFLATE, LINCOLN andULTRAFLO type plugs
• Also available with integrated flow control
• Made from tough anodised aluminium
WWAARRNNIINNGG
These swivel connectors should not be used onpercussion tools or in areas of high mechanical abuse.
WWAARRNNIINNGG
These swivel connectors should notbe used on percussion tools or inareas of high mechanical abuse.
62.704C
62.720Cwith flow control
The weight and stiffness of an air hose applies pressure to the wrist and hands of the tooloperator.
This will limit tool manoeuvrability and tire the operator, and can cause Carpel TunnelSyndrome, back pain and other injuries. Swivel fittings are designed to limit these effectsand improve worker productivity.
62.705C
SWIVEL FITTINGS
ALUMINIUM SWIVEL FITTINGS
62.710Cwith universal coupler and flow control
UNIVERSAL COUPLER fits all 5 plug styles
PROBLEM SOLUTION
325
326
TO
PR
ING
P3
62.312C
62.321C
• Designed to provide 360° of rotation and up to30° of deflection for air tool supply lines
• Nickel-plated hardened steel construction
Free angle fittings, for their part,provide increased mobility withbetween 30° and 75° of flex and360° freedom.
These fittings therefore reduce wristfatigue and improve productivity whileremaining very compact.
62.355C
62.360C
MAXPRO 30° FREE ANGLE FITTINGS
45° FREE ANGLE FITTINGS
FLEX FREE ANGLE FITTINGS
62.382C
62.385C
• Designed to provide 360° of rotation and up to 45°of deflection for air tool and air hose supply lines
• Double pivot design provides more freedom ofmovement
• Nickel-plated hardened steel construction
• Designed to provide 360° of rotation and up to 75°of deflection for air tool and air hose supply lines
• Polyurethane central section provides more free-dom of movement
• Nickel-plated hardened steel construction
323
322
324
TO
PR
ING
WRIST FATIGUEPPEEAAKK PPEERRFFOORRMMAANNCCEE
P4
When a fitting comes loose from a pres-surised hose or when a pressurised hose isruptured, the hose starts blowing com-pressed air in an uncontrollable way. Thiscauses the hose to whip and can result in:
InjuryDamage to work piecesDust being blown up from the floorSmall components being blown around
21.4693/8 industrial
20.4491/4 industrial
22.4691/2 industrial
TOPQUIK ANTI HOSE WHIP SAFETY COUPLERS• Prevents dangerous hose whip
through two-step disconnection
• Heavy duty shock and crushresistant coupler providesexceptionally long service life
• Non-marring materials preventscratching of delicate surfaces
• Super light weight contributesto ergonomics and safety
• Low disconnection noise redu-ces workplace noise pollution
• Meets ISO 4414 safety standards
• Disconnection sound level ofonly 80 dB
12
Slide the sleeve back to releasedownstream pressure. The plug is released, but held within the coupler
SAFETY COMES FROM 2 STEP DISCONNECTION
Slide the sleeve forward. The plug is releasedcompletely
31.749
ULTRAFLO couplers increase airflow for better air tool performance.
TOPQUIK ULTRAFLO
ELIMINATING
90
117
TO
PR
ING
1 2
PPEEAAKK PPEERRFFOORRMMAANNCCEE
The anti hose whip safety valve is an inline emergencyshutoff valve.
Under normal flow conditions the valve is open.
Under failure conditions, the pressure drop is suffi-cient to overcome the force of the valve spring and thevalve closes - the air is shut off.
As a reminder to shut off the air supply a smallamount of air continues to bleed after shut off at arate of 9 SCFM (leaks will be audible).
When the hose is repaired and the compressed air isswitched back on again, the valve repressurizes thedownstream system.
When the pressure on either sideis equalized, the valve opens complete-ly and the system is automaticallyreset.
ANTI HOSE WHIP SAFETY VALVE
58.9521/4 NPT • 18 SCFMAvailable up to 1 NPT • 200 SCFM
TYPICAL INSTALLATIONAnti hose whip safetyvalves should beinstalled upstream ofthe air hose.
TTEECCHH TTIIPPOSHA standard no. 1926.302(b)(7) states that: « All hoses exceeding1/2 inch inside diameter shall have a safety device at the source of supplyor branch line to reduce pressure in case of hose failure. » TOPRING antihose whip safety valves satisfy this standard.
Hose whip is very dangerous and can reach speeds ofup to 150 km/h. This is why it is imperative that hosewhip be prevented !
DANGEROUS HOSE WHIP
252
P5
TO
PR
ING
PPEEAAKK PPEERRFFOORRMMAANNCCEE
P6
PIPING ADAPTORS (Set of 2)
Designed to install or remove basicunits without direct pipe connectionsto the units.4 screws and 2 O-rings included.
Maintenance becomes very simple withTOPRING modular FRL units.
The biggest challenge with standard type FRL units requiring brass pipe fittings is screwing the unit onto opposing ends of air linepiping (while tightening one end, the other end is being loosened!).
With the piping adaptors available for TOPRING modular FRLs, the unit is installed by simply screwing the piping adaptors onto thetwo ends of the piping and sliding the FRL unit into place, securing it with the provided screws and O-ring seals.
Removal for maintenance purposes is just as simple, requiring only the removal of the retaining screws in order to slide the unit out.
Maintenance is difficult with standardFRLs.
• A filter increases tool life and toolperformance by eliminating contami-nants and water
• A regulator with built-in push-pulladjusting knob avoids accidentalchanges to set pressure
• A mist lubricator lubricates tools andincreases their useful life
• High flow unit, ideal for use with mostrotating air tools
• Piping adaptors included to facilitateinstallation, removal and maintenance
• Gauge included
• Sizes available: 1/4 MINI (39 SCFM);1/4, 3/8, 1/2 REGULAR (68 SCFM);1/2, 3/4 MAXI (127 SCFM)
50.630.013/8 NPT
INTEGRATED FILTER AND REGULATOR TO SAVE SPACE
50.530.01 3/8 NPT
DISTINCT UNITS TO FACILITATEMAINTENANCE AND REPLACEMENT
COMBINATION UNITS 205 204
MODULARITY SAVES TIME AND MONEY
Compressed air contains many contaminants, including water, watervapours, oil vapours and solids (dust, etc.). All of these contaminants willdamage tools and reduce their performance levels.
The use of an FRL unit (filter, regulator, lubricator) is one ofthe best ways to protect tools and ensure their bestperformance.
TO
PR
ING
AIR POWER THROUGHAIR PREPARATION
PPEEAAKK PPEERRFFOORRMMAANNCCEE
TO
PR
ING
INTELLIGENT ELECTRONIC AUTOMATIC DRAIN
• Allows true programming of drain times based on rate ofcondensate generation
• True digital timer control allows virtually limitlessprogramming control
• Valve can open at millisecond to 99 hour intervals • Helps conserve air supply and reduces demand on the
compressor• Fully automatic - no maintenance • Large-orifice valve ensuring a self-cleaning process• Strainer with bypass protects valve and allows for
convenient, easy access and removal of particles thatcould block the valve
PROGRAMMABLE DIGITAL COMPACT AUTOMATIC DRAIN
REDUCING WATER IN AIR TOOLSOne of the best ways to avoid water in air tools is to eliminate it at the source, that is, at the compressor.
While this is not the only thing that needs to be done (dryers, filters), elimination of liquid water from the compressor tank is the firststep and will considerably reduce the water that gets into the air distribution system and, as a consequence, the air tools.
INTELLIGENTELECTRONICAUTOMATICDRAIN
BALL VALVE
Y STRAINER
COMPRESSORTANK
COMPRESSOR TANK
256
257
59.400
ZERO AIR LOSS COMPLETELYAUTOMATIC
TTEECCHH TTIIPP
Efficient with air receivers, refrigerateddryers, separators and drop legs
CYCLE TIME
UP TO 99 HOURS
MILLISECONDSTO 99 HOURS
PURGETIME
PROGRAMMABLE
59.360
P7
PPEEAAKK PPEERRFFOORRMMAANNCCEE
• Expels only in the presence of water
• Conserves air supply and reducesdemand on the compressor
• Eliminates the problem of condensationin pneumatic systems
• Special detector verifies the presence ofcondensation 50 times per second
• Large orifice can drain up to 300 litresof condensate per hour
• No sensors to foul up; unit functionsequally well with clear water or heavilyemulsified and dirty condensate
• Requires no anti-siphon pipeline
• Specially designed direct-operatingvalve with a large orifice protectsagainst blockage
• Automatic re-set protectsthe drain from voltagepeaks or other electricalsupply problems
69.401
69.450
P8
TO
PR
ING
A CRUCIAL STEP FOR TOOL PERFORMANCE
• Automatically lubricates a tool byfeeding a measured amount of oilmist each time the tool is cycled
• An effective alternative to larger,more costly units that may not deliverlubricant to the tool due to excessivehose length
• Provide instant oil flow so critical to
time cycled air tools such as staplersand nailers
• Will not leak lubricant into the air lineupon pressure drop or when discon-nected from the air line
• Attaches directly to the air tool inlet
Air tools cannot function efficiently without proper lubrication; the majority of toolbreakdowns are caused by inadequate tool lubrication. Lubrication of tools is thereforethe most important preventative maintenance activity.
This lubrication needs to be constant anddaily, ideally through the use of a lubricatorinstalled as close as possible to the tool.
TOOL LUBRICATION
IN-LINE LUBRICATOR
AIR TOOL OIL
SYNTHETIC AIR TOOL OIL
62.112C
TTEECCHH TTIIPPFor maximum protection it is recom-mended that a sand filter be used inconjunction with In-Line Lubricators.
TTEECCHH TTIIPPA lubricator uses an average of 1 litre of lubri-cant every 2 to 3 months
69.050
69.101
4 litre container also available: 69.104
321
383
384
• High performance mineral lubricant spe-cially formulated to obtain maximum out-put from all types of impact wrenches,hammers, grinders, sanders and all otherpneumatic tools and equipment
• Formulated with high quality additives
• Prevents rust formation and virtuallyeliminates the problems of tarnish andcarbon build-up
• Does not contain any detergent
4 litre container also available: 69.404
• Synthetic formulation that lubricates andprotects pneumatic tools subjected toextreme temperatures varying from -55°C(-67°F) to 250°C (482°F)
• Protects tools in heavy-duty applicationswhere the work could overheat the tool
• Reduces wear, prolonging tool life plusreducing maintenance costs
• Prevents rust and dissolves sludge anddeposits typical in compressed air systems
TTEECCHH TTIIPPIt is recommended that a small amount oflubricant should be squeezed into the toolbefore storage
PPEEAAKK PPEERRFFOORRMMAANNCCEE
MINI HVLP REGULATOR
CONTROL IS CLOSE TO HAND
62.120C
IN-LINE FILTER
It’s not always practical to use a wall-mounted FRL unit to protect and control tools.There are several other options available for improving tool performance directly atthe tool, in «in-line» mode.
The products on this page will allow the operatorto control and protect tools at the tool.
• Used directly upstream of paint sprayguns as final protection
• Removes all traces of water vapours,oil vapours and dirt
• 40 micron porous bronze elementremoves fine dirt particles, an oilabsorbing media removes oil va-pours, and desiccant beads absorbwater vapours
• Desiccant color change indicates thefilter/dryer needs to be replaced
Air contaminatedby water and oil
vapours
Cleandry air
Removes residual desiccant dust
Removes oil vapours
Removes water vapours
Removes dirt
• Designed specifically for the pro-tection of small air tools
• Built-in 40 micron porous bronzeelement to remove water, oil andparticles from contaminated air-
supplies and to ensure a cleansupply of air
• Lightweight and compact
• For in-line installation
315
P9
62.150CTO
PR
ING
319
328HOSE WHIP• Used between the air tool and coupler to
extend the life of the coupler by acting asa shock absorber and protecting it againsttool vibration
• Allows the operator an easier and widerrange of motion, reducing worker fatiguewhile increasing productivity
• Highly recommended fortools that produce heavyvibration such as air hammers andimpact wrenches
• Prolongs hose and coupler life by actingas a "Shock Absorber”
• Specially designed fortools and any spray gun(including HVLP) for accu-rate pressure regulation
• Lightweight air regulatorand gauge combinationprovides superior colormatching capability
62.125C
TTEECCHH TTIIPPAll sharp bends on hoselines should be avoided.These tend to shorten hoselife, increase pressure drop,retard swivel action, incre-ase pump load and raise thetemperature of the fluid.A hose whip should beinstalled to avoid strain onhose and coupler assembly.
IN-LINE DESICCANT DRYER/FILTER 316
62.542
PPEEAAKK PPEERRFFOORRMMAANNCCEE
• Spiral polyester yarn reinforcementprovides superior pressure handlingto other Polyurethane hoses
• Excellent abrasion resistance
• Kink-resistant
• Transparent color allows visualinspection of lubrication or contami-nation
P10
CHOOSING AN AIR HOSE FOR
SUPERCOIL HIGH PRESSURE REINFORCED POLYURETHANE AIR HOSE
• Ideal for outdoor and indoor contractor use
• Excellent aging properties - up to 10 times longer lifetime thanconventional rubber hose
• Lightweight and flexibility contribute to the prevention of work-related injuries
• Highly kink-resistant
• Re-usable swivel fittings with bend restrictors
FLEXAIR CLEAR POLYURETHANE AIR HOSE
ERGONOMIC HIGH PRESSURE
16.620
TO
PR
ING
78
399
ERGONOMIC
74.164
Swivel fitting atsupply connectionallows maximumdirectional flexibi-lity
Rigid fitting at tool end to
ensure a safer connection and
better vibration resistance
Rubber, PVC, Polyurethane… there exists a multitude of materials forair hoses and each has its strengths and weaknesses. The properchoice of air hose based on application, environment and budget iscrucial to getting the maximum performance possible.
PPEEAAKK PPEERRFFOORRMMAANNCCEE
The best in tool performance, air system delivery andoperator efficiency will all be wasted if the air hose does notmeet expectations. TOPRING offers air hoses for themajority of applications.
P11
MAXIMUM PERFORMANCE
• “Lock-on” hose simplifiesmaintenance: for repairs,simply cut hose squareand insert “lock-on” fitting
• Flame retardant cover pro-tects hose in presence ofhot chips and sparks
• Maximum resistance to oilsfor longer life in oily, greasyenvironments
• Accepts re-usable “lock-on”fittings
• Performs well at both highand low temperatures
TOPFLEX LOCK-ON AIR HOSE
• The ideal hose for indoor and outdoor construction applications
• Remarkable flexibility
• Excellent performance even in intensely cold weather
• Easy to roll up after use
• 35 % lighter that rubber hose
• Good resistance to oils and abrasion
• Non-marking outer cover
TO
PR
ING
392
For most air tool applications, the properair hose size is at least one size larger thanthat of the air inlet pipe-thread.
Use of a smaller than recommended hosesize will result in a serious reduction oftool performance.
MINIMUM AIR HOSE SIZE (IN)Approximate Length of run air consumption(SCFM) 25' 35' 50' 100'
1 - 5 1/4 1/4 1/4 5/165 -10 5/16 5/16 3/8 3/8
10 - 20 3/8 3/8 1/2 1/220 - 40 1/2 1/2 1/2 3/440 - 70 3/4 3/4 3/4 170 + 3/4 3/4 1 1
EASYFLEX MULTIPLE PURPOSE PVC AIR HOSE
TOPRIN
G
• new p
roduct •
72.364
77.322
ULTRA FLEXIBLE
SPARK RESISTANT
MAXIMUM OILRESISTANCE
TTEECCHH TTIIPPTOPFLEX "lock-on" hose is not recommended forapplications where vibration or pressure surges occur.
PPEEAAKK PPEERRFFOORRMMAANNCCEE
P12
• Powerful safety air guns• Aluminium venturi nozzle increases the available thrust by up to 250 %• Meets OSHA standards
AIRPRO VENTURI TIP HIGH FLOW BLOW GUN
Venturi nozzle serves 2 purposes:
1 Air flow speeds up as it passes through the nozzle,drawing in ambient air through two side ports.Increased velocity and volume of air exiting the noz-zle boosts available thrust up to 250 %.
2Should the nozzle tip be blocked, the main air flowexits through the side ports. Static pressure at thenozzle tip is held to less than 30 PSI, satisfying OSHAsafety standards.
60.386
HIGHPERFORMANCEERGONOMIC SAFE
MAGNUM EXTRA THRUST VENTURI TIP BLOW GUN
271
287
BLOW GUNS What do we look for in a blow gun? It has to blow hard!Blow guns are evaluated based on their output thrust,usually indicated in pounds of outlet thrust.
Blow gun performance therefore depends on two things:1. air flow through the gun2. amplification devices used
HIGHPERFORMANCEERGONOMIC SAFE
1
2
• Designed to quickly move large volumes of debris• Provides maximum thrust from available air• Extra thrust Venturi tip increases thrust by up to 250 %• Up to 3.3 lbs of thrust at 100 PSI• Maximum air consumption: 65.2 SCFM• 3/8 (F) NPT inlet
TO
PR
ING
60.620
NNOOTTEEThe ideal blow gun for:• Cleaning equipment in paper and textile mills, metal cutting
and wood-working equipment• Blowing floor debris into piles• Cleaning masonry forms, tanks, ovens, large moulds• Cleaning machinery• Cleaning storage areas• All applications where maximum blow gun thrust is required
PPEEAAKK PPEERRFFOORRMMAANNCCEE
P13
• Designed to quickly move large volumes ofdebris
• Extra thrust Venturi tip increases thrust by upto 375 %
• Maximum air consumption: 32 SCFM
• Up to 3.2 lbs of thrust at 100 PSI
• Designed specifically for heavyduty industrial and constructionapplications
• Quickly moves large volumes ofdebris by delivering 100 % ofthe power provided by the aircompressor
• The most powerful blow gunavailable
• Venturi tip nozzle increasesthrust by up to 100 %
• Maximum air consumption:302 SCFM
• 3/4 (F) NPT inlet
TOPGUN EXTRA THRUST VENTURI TIP BLOW GUN
TYPHOON EXTREME PERFORMANCE BLOW GUN
HIGHPERFORMANCEERGONOMIC
60.460
281
It’s obvious that the volume of air passing through a blow gun will have a majorimpact on thrust. Most high flow glow guns increase this air flow by using aVenturi tip.
MAXIMUMTHRUSTERGONOMIC SAFE
289
IT’S THE THRUST THAT COUNTS
TTEECCHH TTIIPPTYPHOON blow guns are designed to provide 100 % of com-pressor power. In order to do this, airflow must be sufficient from thecompressor to the gun. A minimum 3/4 ID hose and 1/2 ID couplingare recommended to ensure maximum performance.
375%MORE
THRUST
Prod Thrust Flow SCFM No lb at 100 PSI
60.386 1.1 10.6
60.460 3.2 32.0
60.620 3.3 65.2
60.700 16.0 208.0
AIR VOLUME
60.700 TO
PR
ING
PPEEAAKK PPEERRFFOORRMMAANNCCEE
P14
VACUUM PERFORMANCE
TopReel HOSE REEL• Heavy-duty steel construction
• Corrosion-resistant epoxy powder coating
• Wide L- shaped base with grooved reinforcement
• Adjustable guide arm for handling up to 9 positions
• Wall, ceiling or floor mounting possible
• Four direction non-snag rollers to reduce hose wear
• Multi-position ratchet lock and easy tension adjustment
• Full flow swivel mechanism
• Fully enclosed and lubricated spring
• Supplied with choice of hose
Just like for blow guns, vacuum performance is a function of airflow. Suction capacity is measured in inches of mercury, to indicatethe vacuum force that the vacuum unit can produce. Air poweredvacuum units often offer superior performance to other types.
Air powered vacuum units also overcome other serious short-comings of industrial electric vacuums by doing away with movingparts, therefore ensuring long service life.
Floor-ceilingMount
FM
Bottom-truckMount
BM
Wall-truckMountWM
TO
PR
ING
411
365
HIGHPERFORMANCE WET/DRY
HOSE REELS ANOTHER WAY TO
INCREASE WORKERPERFORMANCE
67.500
Pivoting bases are also available when the reel must be aligned with thehose direction
Untangling air hosesis a waste of time
that affects workerproductivity.
Even if the righthose is beingused, the clutter-ing up of workspaces can reduce
efficiency and causeaccidents.
The use of hose reelscan increase productivitywhile avoiding accidents.
Barrel and dolly not included
POWERVAC VACUUM UNIT
79.906with 3/8 x 33 ft hose
PPEEAAKK PPEERRFFOORRMMAANNCCEE
• Versatile, transforms an ordinary 205 L steel drum (22 gaugeor higher) into a powerful industrial dry and liquid vacuumcleaner
• Powerful, provides up to 17 in HG of suction for pick-up ofheavy debris and high viscosity liquids
• No moving parts or electricity ensures maintenance-free operation
• Safe, eliminates possibility of electric shocks often associatedwith motor-driven pumps.
• Simple filter assembly sits in top of drum
• Easily replaceable cloth filters
• Dust free operation
• Quieter than electric vacuums
P15
PPEEAAKK PPEERRFFOORRMMAANNCCEE
Pressure before Pressure after
PRE-SET PRESSURE REGULATOR 317
62.202C27 PSI
Air tool users often tend to boost working pressure in the mistaken impression that this willimprove tool performance. This will not actually boost tool performance, but will risk dama-ging tools and causing an accident that could lead to injury. For example, where blow gunsare used, operating at a pressure over 30 PSI can be very dangerous to the worker.
Tamper-proof preset regulators cannot beadjusted and are therefore an ideal choice foravoiding these problems.
AVOIDING PRESSURE SURGES
SAFE PERFORMANCE
• Ensures optimal air tool efficiency by supplyinga constant pre-set pressure
• Increases user safety by avoiding pressuresurges
• Limits over-consumption of compressed air,thereby reducing energy costs
• Available for many commonly used pressurelevels from 15 to 115 PSI
Maximumpressure 30 PSI
Ideal pressure 90 PSI
TTEECCHH TTIIPP
• The ideal pressure for air tools is usual-ly 90 PSI
• Every 15 PSI of overpressure wastes6 to 10 % energy
• According to OSHA standards, blowguns should not exceed 30 PSI in orderto be safe
Pre-set regulators are an economical way to maintain ideal pressure!
TO
PR
ING