THESE ARE SOME COMMAND LINE ENTRIES

Add All (TYPE) WITHIN POSITIONAdd All (TYPE) WITH (EXPRESSION) FOR ELEMENTAdd All (TYPE) WITH (EXPRESSION) WITHIN POSITION

You can also user it to remove or enhance

Rem All (TYPE) WITHIN POSITIONEnhance All (TYPE) WITHIN POSITION

TYPE: SCTN, PANE, FRMW, EQUI, STRU, PIPE, ECT...EXPRESSION: MATCHW(NAME OF STRU, '*TEST*')ELEMENT: CE, STRU, PIPE, EQUI, ZONE, SITE, WORLDPOSITION: E 100 N 100 U 100 TO E 200 N 200 U 200POSITION: VOL CE DISTDIST: ADDITIONAL VOLUME

show _CDCOMP to show the Piping Components form

Q ADEG (DRAFT) GIVES THE C/VIEW ANGLE ( ie 90 DEG )Q ANGLE (HVAC) GIVES THE CE ANGLEQ ATEX(DRAFT) GIVES THE SLAB/GLAB TEXT ATTRIBUTES Q ATT GIVES THE CE ATTRIBUTESQ BANG GIVES THE CE BETA ANGLEQ BORE (PIPING) GIVES THE PIPE INSIDE DIA.Q BSRF (DRAFT) GIVES THE ATTACHEDDRG/SHT (DRWG LVL) Q BTEX(DRAFT) GIVES THE DEAD TEXT ATTRIBUTES Q CHEI (DRAFT) GIVES THE TEXT CHARACTER HEIGHT Q COL ACT GIVES THE CURRENT ACTIVE COLOUR Q COL AIDS GIVES THE CURRENT AID LINE COLOUR Q COL CE GIVES THE CURRENT ATTRIBUTED COLOUR Q COL VIS GIVES THE CURRENT VISIBLE COLOUR Q COL 4 (ETC) GIVES THE ATTRIBUTED COLOUR (YELLOW)Q CREF GIVES THE CONNECTION REFERENCEQ CUTL GIVES THE CE CUT LENGTHQ DDNAME(DRAFT) GIVES THE DIMENSION OWNERS NAME Q DER LEN GIVES THE CE EXACT LENGTHQ DER ORI GIVES ORIENTATION OF ‘CE’Q DESC GIVES THE CE DESCRIPTIONQ DESP GIVES THE CE DESPERAMETERSQ DIR (DRAFT) GIVES THE C/VIEW DIRECTION( IE N )Q DISPLAY GIVES THE TOLERENCE & REPRES LEVELSQ DMTXT(DRAFT) GIVES THE DIM TEXT ATTRIBUTESQ DNST GIVES THE CE DENSITY Q DPOS (DRAFT) GIVES THE LDIM POSITION ON SHEETQ DRNE GIVES THE END CUT-PLANE DIRECTIONQ DRNS GIVES THE START CUT-PLANE DIRECTIONQ DTER (DRAFT) GIVES THE LAYER/LDIM TERM’TR DEFAULT

Q TYPE GIVES THE FRMW STYLE TYPE(ie STLS)Q E GIVES THE CE EAST CO-ORDINATEQ ELEM GIVES THE CE ELEMENT NAMEQ FRAD GIVES THE PLOO/PAVE RADIUS ie 100mmGIVES THE NXTR/VERT RADIUS ie 100mmQ FPT (DRAFT) GIVES THE STRA FROM POINT CO-ORDS. Q FUNC GIVES THE CE FUNCTIONQ GCOF GIVES THE CE GROSS C OF GQ GTYP GIVES THE GENERIC TYPE ie OD,HP,TGQ GWEI GIVES THE CE GROSS WEIGHT Q HEI GIVES THE CE (PLOO LVL) PLT THKQ HH (PIPE SUPPT) GIVES THE CE HANGER HEAD CO-ORDS

Q HPOS (PIPING) GIVES THE CE PIPE HEAD CO-ORDINATESQ HT (PIPE SUPPT) GIVES THE CE HANGER TAIL CO-ORDSQ IDP @ WRT/* GIVES THE CE P POINT CO-ORDINATESQ IDPL@ GIVES THE PLINE NAME USING CURSOR Q INREF GIVES THE CE INREFERENCEQ ISPEC (PIPING) GIVES THE CE (PIPE) INSULATIONQ JLIN GIVES THE CE JOINT LINEQ JUSL GIVES THE CE JUSTIFICATION LINE Q LEN (DRAFT) GIVES THE STRA LENGTH Q LEV GIVES THE CE LEVEL (OBSTRUCTION ETC)Q LHEI (DRAFT) GIVES THE TEXT LETTER HEIGHTQ LIST GIVES THE CE FITTINGS (NEG EXTR. ETC.)Q LOCK GIVES THE LOCK STATUSQ LSHAPE (DRAFT) GIVES THE LABEL LEADER LINE STATUSQ MATREF GIVES THE CE MATERIAL REFQ MDB GIVES THE PROJECT DATABASEQ MEM GIVES THE CE MEMBERSQ MEML GIVES THE CE MEMBER LINEQ MIDP GIVES THE CE MIDPOINT CO-ORDINATESQ MPT (DRAFT) GIVES THE STRA MID POINT CO-ORDS Q MTO GIVES THE CE MTO STATUS Q NAM GIVES THE CE NAMEQ NCOF GIVES THE CE NET C OF GQ NSRF GIVES THE CE NET SURFACEQ NVOL GIVES THE CE NET VOLUME Q NWEI GIVES THE CE NET WEIGHTQ OBS GIVES THE CE OBSTRUCTION LEVEL Q ORI GIVES THE CE ORIENTATION (SLOPE)Q OWN GIVES THE CE OWNERQ PA (PIPING) GIVES THE CE ARRIVE CO-ORDINATES Q PARA GIVES THE CE PARAMETERS ie SERIAL SIZESQ PH (PIPING) GIVES THE CE PIPE HEAD ATTRIBUTES Q PH BORE (PIPING) GIVES THE CE (PIPE HEAD) BOREQ PH OD (PIPING) GIVES THE CE (PIPE HEAD) DIAMETERQ PT OD (PIPING) GIVES THE CE (PIPE TAIL) DIAMETER Q PI WRT/* (PIPING) GIVES THE CE (PIPE SUPPT) LOCATIONQ PKEY (DRAFT) GIVES THE DIM PLINE STATUS (ie TCTF)Q PL WRT/* (PIPING) GIVES THE CE HVAC LEAVE CO-ORDINATESQ PLTXT(DRAFT) GIVES THE PROJ TEXT ATTRIBUTESQ POS GIVES THE CE CO-ORDINATES (START / ORIGIN)Q POS IN $V1 GIVES THE CE DISTANCE TO VAR. $V1Q POSE GIVES THE CE END CO-ORDINATESQ POS FITT GIVES THE C/FITT CO-ORDINATES (START)Q POS PLRF (DRAFT) GIVES THE CURRENT VSEC CO-ORDS. Q POS IDPL@ GIVES THE PLINE CO-ORD AT CE START Q POS PPLI BOS WRT/* GIVES THE BOS PLINE CO-ORDINATESQ POS PPLI NA PROP 0.5 GIVES THE CENTRE CO-ORDINATE POSITIONS OF THE PLINE (PPLI) AT(0.5 x DER LEN) ON THE N/AQ POSS GIVES THE CE START CO-ORDINATESQ POSS POSE GIVES THE CE BOTH END CO-ORDINATESQ POS WRT/* GIVES ORIGIN OF CE WITH REGARD TO WORLDQ PT (PIPING) GIVES THE CE PIPE TAIL ATTRIBUTES Q RAD (HVAC) GIVES THE CE RADIUSQ REF GIVES THE CE PDMS REFERENCE NO.Q REPRES GIVES THE CE REPRESENTATION STATUSQ FUNC GIVES THE CE FUNCTION Q RRSF (DRAFT) GIVES THE CURRENT VIEW RULE SETTINGSQ SIZE (DRAFT) GIVES THE VIEW O/ALL DIMENSIONS

Q SJUS GIVES THE PLOO JUSTIFICATION ie UTOPDCENDBOTQ SNAP (DRAFT) GIVES THE SNAP SETTING (ON/OFF) Q SPRE GIVES THE CE SPECIFICATION REFERENCEQ TCTL OR (Q CUTL) GIVES THE CE CUT LENGTH?

Q THPOS (DRAFT) GIVES THE C/VIEW MATCHLINE CO-ORDSQ TMRF (DRAFT) GIVES THE CE (SYMBOL) NAMEQ TPOS (PIPING) GIVES THE CE PIPE TAIL CO-ORDS.Q TPT (DRAFT) GIVES THE STRA TAIL POINT CO-ORDS. Q TYPE GIVES THE CE TYPE ie SCTN ,PANEQ USER GIVES THE CE USER DATABASEQ VOL CE GIVES THE CE VOLUMEQ VLIMITS (DRAFT) GIVES THE VIEW LIMITS

Q VSCALE (DRAFT) GIVES THE C/VIEW SCALE ( ie 0.5 )0.5 = 1:20.2 = 1:50.1 = 1:100.05 = 1:200.04 = 1:250.02 = 1:500.01 = 1:100

Q VTYP (DRAFT) GIVES THE VIEW ATT(ie.GLOBAL HIDDEN) Q XYPOS (DRAFT) GIVES THE VIEW POSITION ON SHEETQ ZDIS GIVES THE CE FITTING DIST FROM START

PDMS TYPED COMMANDS

ADD CE ADDS CEADD CREF ADDS CE PIPE CONNECTION REFADD CE COL 39 ADDS CE WITH COL 39(SEE COLOUR SHEET)ADD ALL WITHIN VOL CE ADDS ALL DISCIPLINES THAT OVERLAP CEADD ALL WITHIN VOL CE 100 ADDS ALL DISCIPLINES THAT OVERLAP CE WITH A VOLUME OF 100mm ALL ROUNDADD ALL SCTN WITHIN VOL CE ADDS ALL SECTIONS THAT OVERLAP CEADD ALL EQUIP WITHIN VOL CE ADDS ALL EQUIPMENT THAT OVERLAPS CEADD SITE ADDS CE SITEAID CLEAR LINE ALL REMOVES UNWANTED LINES FROM PDMSAT @ MOVES CE TO NEW CURSOR POSAT IDP@ MOVES CE TO SELECTED PPOINTAT IDPL@ MOVES CE TO SELECTED PLINEAXES AT CE PLACES CE AXESAXES OFF REMOVES CE AXESBY D100 (PDMS ONLY) MOVES CE DOWN 100 mmBY E100 (PDMS ONLY) MOVES CE EAST 100 mmBY N100 (PDMS ONLY) MOVES CE NORTH 100 mmBY U100 (PDMS ONLY) MOVES CE UP 100 mm

BY X100 (DRAFT & PDMS) MOVES CE X (EAST) 100 mmBY X100 WRT/*(PDMS PLATES) MOVES CE X (EAST) 100 mm WRT TO WORLDCHE CE GIVES CONSISTANCY CHECK ON CE COL ACT BLUE CHANGES THE ACTIVE COLOUR TO BLUECOL CE VIOLET CHANGES THE CE COLOUR TO VIOLET COL 39 YELLOW CHANGES LINE COL TO YELLOWDELETE CE DELETES THE CE EXT END TO IDPL@STA EXTENDS THE END TO A SELECTED PLINE EXT END -1000 EXTENDS THE END –1000FINISH ENDS & SAVES PDMS SESSIONFLIP CE FLIPS CE

GETWORK GETS LATEST MODELINCL CIRC 1 OF NOTE/TABLE REPOSITIONS CIRC 1 TO PREV. SELECTED DESTINATIONINCL ID@ GIVES THE CE CO-ORDINATES (START)OR ITEM TO BE TRANSFERED INCL NAME………………… REPOSITIONS CE TO A SELECTED DESTINATIONLOCK ALL LOCKS CE & CE MEMBERSMAR CE MARKS CE NAMENAME /TEMPORARY RENAMES SAID ITEM TO TEMPORARY

NEW FITT COPY PREV BY ZDIST PROP 1 BANG 180 COPIES FITT AT END POITION OF CE AT ABANGLE OF 180PROP 0 START POSITION CEPROP 0.5 MIDDLE POSITION CEPROP 1 END POSITION CE

NEW GLAB COPY $V1 COPIES GLAB AS VARIABLE $V1NEW GLAB COPY PREV AT @ COPIES GLAB TO PICKED LOCATIONNEW SCTN COPY PREV BY E200 (PDMS) COPIES CE E200NEW SCTN COPY PREV BY E200 COL 4(PDMS) COPIES CE E200 COL 4NEW PANE COPY PREV BY E200 COL 4(PDMS) COPIES CE E200 COL 4NEW TEXP COPY PREV BY Y10 (DRAFT) COPIES CE Y10NEW SYMB COPY PREV BY X-10 (DRAFT) COPIES CE X-10NEW VRTX COPY PREV BY X10 (DRAFT) COPIES CE X10 (CLOUDS)PKEY LTOC CHANGES DIM FROM EXIST JUSL TO LTOCREFRESH REFRESHES THE SCREENREM CE REMOVES THE CE RENAME /XXX /YYY RENAMES CE TO YYY REPRES DARC 1 SETS ARC TOLERENCE TO 1mm REPRES DARC DEF SETS ARC TOLERENCE TO 10mm (DEFAULT) REPRES HOLES ON ADDS HOLES REPRESENTATION (Apply ‘Add’ in Drawlist)REPRES OBSTRUCTION OFF REMOVES OBSTRUCTION REPRESENTATIONREPRES HOLES OFF REMOVES HOLE REPRESENTATION (Apply ‘Add’ in Drawlist)REPRES PNODE COL YELLOW PRIMARY NODES SHOWN YELLOW REPRES PNODE ON PRIMARY NODES SHOWN ONLY REPRES PNODE SIZE 6 CHANGES PRIMARY NODES TO 6mmREPRES PROF ON CL OFF SETS PROFILE REPR AS SOLID REPRES SNODE OFF SECONDARY NODES OFF ROT THRO POSE ABO D BY 30 ROTATES CE ABOUT END POS BY 30 DEG ROT THRO POSS ABO D BY 45 ROTATES CE ABOUT START POS BY 45 DEG ROT THRO MIDP ABO D BY 90 ROTATES CE ABOUT MIDP POS BY 90 DEG ROT ABO IDP@ BY 90 ROTATES CE LOCAL TO PPOINT BY 90 DEG.ROT ABO IDPL@ BY 90 ROTATES CE LOCAL TO PLINE BY 90 DEG.ROT THR IDP@ BY 90 ROTATES CE ABOUT ANY PPOINT BY 90 DEG.ROT THR IDPL@ BY 90 ROTATES CE ABOUT ANY PLINE BY 90 DEG.ROT ABO P1 BY 90 ROTATES CE ABOUT P1 BY 90 DEG.SAM LETS YOU TOGGLE BETWEEN LAST 2 ITEMSSAVEWORK SAVES LATEST WORKUNCLAIM ALL UNLOCKS ALL CLAIMED MEMBERS UNLOCK ALL UNLOCKS CE & CE MEMBERSUNM CE UNMARKS CE NAMEPREC 4 DP GIVES PRECISE READOUT TO 4 DEC. POINTSZDIST (ZDIST + 100) MOVES ITEM 100 FROM ORIG POSITION

DRAFT QUERY COMMANDS

Note: most of the query commands used in PDMS DESIGN also work in DRAFT

Q ADEG GIVES THE C/VIEW ANGLE ( ie 90 DEG )Q APOF GIVES THE CE (NOTE) TERMINATOR POS’NQ BSRF GIVES THE DRG. SHT. REF. (STRU LVL) Q CHEIGHT GIVES THE TEXT CHARACTER HEIGHTQ CPOF GIVES THE CE (NOTE) LEADER LINE POS’N Q DIR GIVES THE C/VIEW DIRECTION( ie N )Q DPOS GIVES THE LDIM POSITION ON SHEETQ DTOF GIVES DIMENSION TEXT X and Y valueQ DTER GIVES THE LAYER/LDIM TERM’TR DEFAULT Q FPT GIVES THE STRA FROM POINT CO-ORDS Q JUST GIVES THE C/VIEW JUSTIFICATION( ie LEFT )Q LEN GIVES THE STRA LENGTH Q LHEI GIVES THE TEXT LETTER HEIGHT Q LSHAPE GIVES THE LABEL LEADER LINE STATUS

Q LVIS GIVES THE CE VISIBILITYQ MPT GIVES THE STRA MID POINT CO-ORDS Q PKEY GIVES THE DIM PLINE STATUS (ie TCTF)Q PLCL GIVES THE DIM PROJECTION LINE CLEARANCEQ POS PLRF GIVES THE CURRENT VSEC CO-ORDS Q RRSF GIVES THE CURRENT VIEW RULE SETTINGS Q SIZE GIVES THE VIEW O/ALL DIMENSIONSQ SNAP GIVES THE SNAP SETTINGS (ON/OFF) Q THPOS GIVES THE C/VIEW MATCHLINE CO-ORDSQ TMRF GIVES THE CE (SYMBOL) NAMEQ TPEN GIVES THE TEXP COLOUR ATTRIBUTES Q TPT GIVES THE STRA TAIL POINT CO-ORDS Q VLIMITS GIVES THE VIEW LIMITS Q VRAT GIVES SCALE RATIO (ie 1 TO 25)Q VSCALE GIVES THE C/VIEW SCALE ( ie 0.5 )

0.5 = 1:20.2 = 1:50.1 = 1:100.05 = 1:200.04 = 1:250.02 = 1:500.01 = 1:100

Q VTYP (DRAFT) GIVES THE VIEW ATT(ie.GLOBAL HIDDEN)Q XYPOS (DRAFT) GIVES THE VIEW POSITION ON SHEET

DRAFT TYPED COMMANDS

ADEG 0 MODIFIES TEXT HORIZONTALADEG 45 MODIFIES TEXT/PRIMITIVES AT 45 DEG.ADEG 90 MODIFIES TEXT VERTICALAPOFFSET 5 -5 RE-POSITIONS LTER END X5 Y-5AT @ MOVES CE TO NEW CURSOR POSAT IDP@ MOVES CE TO SELECTED PPOINTAT IDPL@ MOVES CE TO SELECTED PLINEBLNK FALSE TEXT REMOVES BLANKED AREA BELOWBLNK TRUE TEXT BLANKS ALL IT OVERLAYSBTEXT’A-A’ MODIFIES TEXT TO A-ABY @ MOVES CE BY LOCT. FROM POS TO NEW POSBY X100 MOVES CE X (EAST) 100 mmBY Y100 MOVES CE X (NORTH) 100 mm CPOFFSET 5 -5 RE-POSITIONS LEADER LINE START X5 Y-5DIM TEX’#100 TYP’ DIMENSION TEXT READS 100 TYPDPOS @ PLACES THE LDIM POSITION BY CURSOR DTAN DEF DIMENSION TEXT DEFAULTDTAN PAR DIMENSION TEXT PARALLELDTAN HOR DIMENSION TEXT HORIZONTALDTAN STAN DIMENSION TEXT STANDARDDTAN VERTICAL DIMENSION TEXT VERTICALDTOF @ DIMENSION TEXT BY CURSORDTOF 0 4 DIMENSION TEXT OFFSET X0 Y4DTAN PAR DTOF 8 0 DIM TEXT PAR. & OFF X-8 Y0NLPN OFF TURNS LINE OFF (IE CLOUD VERTEX)FPT @ MOVES STRA FROM POINT BY CURSORFPT BY X2 Y-2 MOVES STRA FROM POINT BY TYPED INPUTFRAME ON TEXT FRAME ONGAP @ LETS CURSOR DETERMINE DIMENSION GAP GAP DELETE ALL DELETES ALL DIMESION GAPS GAP DELETE AT DELETES DIMENION GAP BY CURSOR GBOX 5 MODIFIES TEXT FRAME WITH 5 CLEARANCEHIGH CE HIGHLIGHTS CE INCL CIRC 1 OF NOTE/TABLE REPOSITIONS CIRC 1 TO PREV. SELECTED DESTINATIONINCL NAME………………… REPOSITIONS CE TO A SELECTED DESTINATIONLEAD STRA CHANGES LEADERLINE TO STRAIGHT

LEAD BENT @ PLACES ANOTHER VERTEX ON LEADERLINE LVIS FALSE TURNS CE VISIBILITY OFFLVIS TRUE TURNS CE VISIBILITY ONLLEAD FALSE LEADERLINE OFFLLEAD TRUE LEADERLINE ONLTER OFF LINE TERMANATOR OFFLTER ARR LINE TERMANATOR ARROWLTER DOT LINE TERMANATOR DOTLTER OBL LINE TERMANATOR DASHMODIFY @ ENABLES MODS TO SLAB/GLAB GEOMETRYNEW CIRCLE DIAM 100 AT@ DRAWS CIRCLE AND POSITIONS BY CURSORNEW CIRCLE RAD 50 AT@ DRAWS CIRCLE AND POSITIONS BY CURSORNEW GLAB COPY $V1 COPIES GLAB AS VARIABLE $V1NEW GLAB COPY PREV AT @ COPIES GLAB TO PICKED LOCATIONNEW RECT XLEN40 YLEN20 ANG 45 ORIG CORNER AT@ DRAWS RECT AND POSITIONS IT BY CURSORNEW GLAB COPY PREV AT@ COPIES TEXT AND POSITIONS BY CURSORNEW ‘element’ COPY PREV BY X20 COPIES ‘element name’ WITH OFFSET BY X20NLPN OFF TURNS LINE OFF (IE CLOUD VERTEX)OSHT 10 DIM LINE OVERSHOOT 10mm OSHT @ DIM LINE OVERSHOOT BY CURSORPLCL@ POSITION LEADER LINE BY CURSORPROJ CLEAR @ SETS PROJECTION LINE POSITION BY CURSORPROJ CLEAR 5 SETS PROJECTION LINE POSITION BY 5mm PROJ TEX’TYP’ PROJECTION TEXT READS TYPPTAN PAR PROJECTION TEXT PARALLELPTAN HOR PROJECTION TEXT HORIZONTALPTAN VERTICAL PROJECTION TEXT VERTICALPTOF -8 0 PROJECTION TEXT OFFSET X-8 Y0RCOD LEFT ROTATES VIEW BOX LEFT REPEAT 5 BY X10 COPIES CE 5 TIMES BY 10mm SPACESSNAP ON/OFF TURNS SNAP ON/OFFSNAP ON 10 GIVES SNAP GRID X10 Y10 SNAP ON SPACING X10 Y20 GIVES SNAP GRID X10 Y20 TPEN 71 GIVES THE TEXP COLOUR ATTRIBUTE 71 TPT @ MOVES STRA TO POINT BY CURSORTPT BY X2 Y-2 MOVES STRA TO POINT BY TYPED INPUT UPDATE ANNO UPDATES ANNOTATION UPDATE DESIGN UPDATES DESIGNUPDATE PICTURE UPDATES GRAPHICSVGRID ON/OFF TURNS SNAP GRID VISIBILITY ON/OFF#<SECTIONA-A UNDERLINES TEXT ie SECTION A-A

#DEF DEFAULT DIMENSION ie 4500

#< #DIM #> UNDERLINES DIMENSION ie 4500

#< #DIM #>#/TYP UNDERLINES DIMENSION ie 45000TYPWEST SHELL #< #> WEST SHELL __________#SPRE(C10:19)UB FORMAT ON DRG. 254x102x22UB#SPRE(C10:16)UB FORMAT ON DRG. 254x102UBEL. #DIMPOSU(C2:5).#DIMPOSU(C6:) FORMAT ON DRG. EL. 508.500EL. + #DIMPOSU(C2:5).#DIMPOSU(C6:) FORMAT ON DRG. EL. + 508.500

GLOSSARY

ATTA PIPE ATTACHMENT REQ’D FOR SRUCTURAL PENETRATIONS THRO DECKS/WALLS ETCFITT STRUCTURAL FITTINGPANE STRUCTURAL PLATE/GRATING SECTIONPAVE P POINT OWNED BY PLOOPFIT PENETRATION THRO’ DECK OR WALL PLATE ( PIPE SLEEVE/ELECTICAL TRANSIT ETC)PLOO PLATE OWNED BY PANE HAS PLATE ATTRIBUTESSCTN STRUCTURAL SECTION ie. HEA,UNP etcSJOI SNOD MEMBER USED IN CONNECTING SCTNSNOD NODE POINT USED IN CONNECTING SCTN STRUCTURAL SECTION ie HEA,UNP etc

VERT P POINT OWNED BY NXT

GEOMETRIC SHAPES

BOXI IMPLIED BOXINGLCYL CYLINDER (Defined by Distance to Bottom & to Top)LPYR RECTANGULAR PYRAMIDLSNO SNOUT (Offset Truncated Cone; similar to eccentric pipe reducer)NSBO NEGATIVE BOXNSCT NEGATIVE CIRCULAR TORUSNSCO NEGATIVE CONENLCY NEGATIVE CYLINDER (Defined by Distance to Bottom & to Top)NSCY NEGATIVE CYLINDER (Defined by Distance to Bottom & Height)NSDS NEGATIVE DISHNLPY NEGATIVE PYRAMIDNSRT NEGATIVE RECTANGULAR TORUSNSSL NEGATIVE SLOPE-END CYLINDERNLSN NEGATIVE SNOUTNSSP NEAGTIVE SPHERESBOX BOXSCTO CIRCULAR TORUS (e.g. Tubular Bend)SCON CONESCYL CYLINDER (Defined by Distance to Bottom & Height)SDIS DISCSDSH DISH (Pressure Vessel End or Similar)SRTO RECTANGULAR TORUS (e.g. Cable Tray Bend)SSLC SLOPE-END CYLINDERSSPH SPHERETUBE TUBING

REPRE DARC 1 Set arc tolerance to 1 degreeREPRE DARC DEF Set arc tolerance by default (10°)REPRE HOLES ON Set hole onREPRE HOLES OFF Set hole offREPRE PNODE COL YELLOW Set pnod colour YellowREPRE PNODE ON Set pnod onREPRES PNODE SIZE 6 Set pnod size 6REPRES PROF ON CL OFF Set profile representation SOLID and Cline offREPRES SNODE ON Set snod on / offREFRESH Refresh the graphic windowPREC 4 DP Give Precision decimal to 4 digitsQ REPRES Give the representation statusCouleurQ COL ACTive Give the active current colourQ COL AIDS Give the actual colour of aidsQ COL CE Give the active colour of CEQ COL VIS Give the visible colourQ COL 4 (Etc…) Give the Attributed colour (YELLOW)COL ACT BLUE Change active colour to BLUECOL CE VIOLET Change CE colour to VIOLETCOL 39 YELLOW Change colour 39 to YELLOWENHANCE CE TRANSL 0 Display CE SOLIDENHANCE CE TRANSL 60 Display CE TO 60% TRANSLUCENCYENHANCE CE COL YELLOW Display CE YELLOW

Q DRAW List the Drawlist display in graphic window.(Take care! could be long if large drawlist

ADD to Drawlisto ADD ALL WITHIN VOL CE Add all elements include and crossing the CEvolume boxo ADD ALL WITHIN VOL CE 100 Add all disciplines that overlap CE with anadditional clearance volume +1OOmm

o ADD ALL SCTN WITHIN VOL CE Add only the SCTN include and crossing the CEvolumeo ADD ALL STRU WITH PURP EQ 'PS' Add only SCTN with their Purpose EQ to ’ PS’o ADD ALL WITHIN VOL CE 500 COL 4 Add ALL within vol CE + 500 colour yellowo ADD CE Can be followed by AUTO CE to zoom adjusted around CEo ADD CREF Add branch connected to crefo ADD CE COL 39 Add CE colour 39o ADD SITE ADD site (be careful this can take time to load)o ADD CE Colour Blue TRANSL 75 Add CE colour blue with 75% of transparencyo ADD HREF TREF ……CREF Add connected branch to href tref or also cref withnozzle or TEEREMOVEo REM CE Remove Current elemento REM ALL Remove all elemento REM PIPE Remove pipe onlyo REM EQUI Remove equi onlyo REM ALL WITHIN VOL CE 100 Rem all include in CE volume boxo ETC……….

MARKo MARK CE Mark CE nameo UNMARK CE or ALL Unmark CE name can be used with ALLo MARk CE Mark CE nameo MARk With 'TEMPORARY' CE Tag CE with temporary name ‘TEMPORARY’o MARk With (NAME OF CATREF) CE Tag CE with the name of Catrefo MARK With (GTYPE) CEo MARK With 'TITI' CEo MARK With (STRING(DESP1) + '_' + NAME OF CATREF) CEo MARK With (STRING(DESP1)) CEo MARK With (STRING(LOHE)) CE Tag PANEL CE with its thickness

AXEo AXES CE Add an Aid axe on current elemento AXE AT ID@ Add an Aid axe on element to be digito AXE OFF Suppress the display

AIDSo AID TEXT (NAME OF CATREF) AT AT P1oo AID TEXT (STRing(DESP1) + '_' + NAME OF CATREF) AT AT P1oo AID TEXT (STRing(MATREF) + '_' + STRing (LOHE) + '_' + NAME OF SPREF) AT AT P1oo AID TEXT (STRing(MATREF) + '_' + STRing (TCTL) + '_' + NAME OF CATREF) AT AT PPLI TOSoo AID TEXT ('MAT:' + STRing (MATREF)) AT AT PPLI LTOS AID TEXT ( 'LONG:' + STRing (TCTL)) ATAT PPLI NA AID TEXT ('TYPE:' +NAME OF CATREF) AT ATPPLI RBOSo AID TEXT ('THK:' + STRing (LOHE)) AT AT P1 AID TEXT ( 'TYPE:' + STRing (SPREF)) AT AT P2 AIDTEXT ('MAT:' + STRing (MATREF)) AT AT P3o AID TEXT ('TYPE:' + SUBSTRING(NAME OF CATREF,14)) AT AT P2 AID TEXT ('ELEVATION:' +STRing (P100 UP IN WORLD)) AT AT P3These commands has been defined with two (AT AT ) values. Don’t ask me why! ?? This is only I havefounded to get the right result.oo AID ARROW AT AT P1 OF CE DIR OPPO PPOINT1 HEI1000oo AID ARROW AT AT P100 OF CE DIR AXES PPOINT100 HEI1000o AID CLEAR ALL To suppress all aid display.ALPHA REQUEST CLEAR Clear the command line window and its display.

MODIF on DESPARAMSo DESP n2 500 n6 300 This change the design parameters number 2 and 6

CREATION d’OBJET PDMSo NEW SUBS /name_of_subs AT IDP@ ORI Y IS N AND Z IS UPo NEW BOX XLEN 500 YLEN 25 ZLEN 50 LEV 5 7 OBST 0o NEW SUBS /name_of_subs COPY PREV BY East 1550o NEW SUBS /name_of_subs POLAR N22.5W Dist 500o NEW BOX XLEN 500 YLEN 10 ZLEN 250o NEW PIPE /flow/area/pipe1o NEW BRAN /flow/nom/pipe1/branch1o NEW ELBOW SELect WIth STYP ELo NEW FLAN COPY PREV FLANAssociate with COPYo COPY PREV MOVE North(43.68 + 180 Add)East DISTance (1243.8 2 Down)(43.68+180) = notation polonaise inverse (43.68 180 ADD)o NEW SCTN COPY PREV BY E200o NEW SCTN COPY PREV BY E200 COL 4o NEW SCTN COPY PREV BY E200 WRT CE - Copy E200 wrt CEo NEW SCTN COPY PREV MIRRO PLANE E THR E 1180 N8000 U2600WRT/*(PDMS) - Mirror copy CE withcoordinates and directiono NEW STRU COPY PREV MOVE W WRT CE TO IDPL@ - Copy a newSTRU and move it west with respect CE andtoward Selected PLINECOPY of GROUP d’objetso COPY MEMber OF /Goup_member_nameo NEW xxx /nom COPY PREVo NEW BOX COPY PREV BOX BY W1250o NEW SUBS /nom_de_la_subs COPY PREV ROTate ABOUT Z BY 45o NEW BRAN /CVT/RRI001 COPY /RRI001 RENAME /RRI /CVT/RRI

Move Objectso MOVE N45E DIST 1500o MOVE S DIST 1245o MOVE U THROugh P2 OF PREV BOXo MOVE ALONG P1 DIST 547o MOVE N45W TOWARDS ID@ DIST 500o MOVE N45W TOWARDS IDP@ DIST 500o MOVE $_DIR WRT WORLD PLANE $_PLAN CLEARANCE $_DIST$_RELATIVE $_CD.NNAME_NAMEo MOVE ALONG $!SCTNDIR1 PLANE U THR U $_ELEVATIONo MOVE P2 North DIST 500 FROM id@o MOVE P2 North CLERANCE 100 THRough IDP@ MOVe E WRT CE TO ID@Move CE wrt its own axe’s East to anelement chosen.o MOVE U TO ID@(PDMS) Move UP TO A Selected ELEMENTo MOVE W TO IDPL@(PDMS) Move WEST TO A Selected PLINEo BY D 1OO Move CE DOWN 100 mmo BY E 100 Move CE EAST 100 mmo BY E 2IN WRT CE Move CE E 2"(INCHES) WRT CE(Determinate... correct CE axis first )o BY E3.lDIN Move CE E3.1/2"(INCHES)o BY N lOO Move CE NORTH 100 mmo BY U lOO Move CE UP 100 mmo BY X lOO Move CE X (EAST) 100 mmo BY X lOO WRT/* Move CE X @AS") 100 mm wrt worldo AT IDP@ Move CE to selected PPOINTo AT IDPL@ Move CE to selected PLINE

Displacement of object according to the normal inthe datum-line

o PLANE N CLEAR 100 BEHIND CE Move Plane North clearance 100 behind CEo PLANE E THROugh PIN 1 Move Plane East through Pin 1o PLANE U DIST 0 BEHIND IDP@ Move Plane Up distance 0 behind ppoint @.o PLANE PIN 2 THRO IDP@ Move pin2 through ppoint @o PLAN N DIST 500 Move to North distance 500o PLAN N THROugh ID@ Move North through element @o PLAN U THROUgh U 1000 Move Up through up dist 1000o PLAN N DIST –200 FROM IDP@ The distance is coming from south (-… equalopposite direction)POSITION Command ( Object position) )o POS PT DIST 500 FROM LAST MEM Pos branch tail 500 from last membero POS PH DIST 500 FROM FIRST MEM Pos branch head 500 from first membero VAR !P1 P1 POS IN WORLD Store P1 pos in variable $!P1o POS AT IDP@ Position at Ppoint chosen.o POS ID@ AT PIN 2 Position object chosen at Pin2o POS P6 AT P2 OF $v1 Position object from its P6 to P2 of chosenoo Q POS WRT TO ID@ Give the distance from CE to start of indentedmembero Q POS IN $v1 Give the CE distance to $V1 variableo Q POS PIN1 WRT/* Give the CE coordinates OF PINlo Q POSE Give the CE END coordinateso Q POS FITT Give the CE FITT coordinates starto Q POS IDPL@ Give the CE PLINE coordinates CE starto Q POS PPLI BOS WRT/* Give the BOS PLINE coordinateso Q POS PPLI NA PROP 0.5 Give the centre coordinate position of the pline(PPLI)at (0.5 x derive length) on the N/Ao Q POSS Give the start coordinateso Q POSS POSE Give the start and end coordinates

Q POS WRT CE TO ID@ Query the distance from CE to identify objecto Q POS IN $V1 Query the distance from CE to $V1 objecto Q POS PIN1 WRT/* Query the position of pin1 wrt worldo Q POS End Query the position end of sctno Q POS FITT Query the fitting coordinates (start)o Q POS IDPL@ Query the Pline coordinates at start of idplineo Q POS PPLI BOS WRT/* Query the bottom BOS pline coordinateso Q POS PPLI NA PROP 0.5 Query the neutral axis NA middle of plinecoordinates (position of the pline at (PPLI) at(0.5 x DER LEN) on the NAo Q POSS Query position start of the SCTNo Q POSS POSE Query position start and end of the SCTNPINSUtilisation des pins.o PIN1 AT PPLI BOS PROP 0.5 POS PIN1 at middle of pline BOSo PIN1 PLAN N THR PIN2 Move the Pin1 through Pin2 with a normal toplan northo PIN1 COPY IDP@ Create pin1 according Ppoint chooseno PIN1 COPY PIN2 Create Pin2 by copy of Pin1o PIN1 DIR D Orient PIN1 downo PIN1 DIR U WRT/* THR IDP@ Move PIN1 UP TO A SELECTED PPOJNTo PIN2 DIR D WRT/* THR IDPL@ Move PIN2 Down to a selected plineo PIN1 BY D 8 Move PIN1 Down 8mmo PIN6 OFF Turn PIN6 OFFo POS PIN3 AT CE Position PIN3 at axis of CEo Q DIR PIN1 Query Pin1 direction

Query PIPING.o Q BORE Give the pipe boreo Q POD1 Give the Outside diameter 1o Q CLLE Give the branch lenghto Q HPOS Give the CE pipe HEAD coordo Q HT Give the CE hanger TAIL coordo Q ISPEC Give the CE (PIPE) insulationo Q PA Give the CE ARRIVE coordinates withRespect World

o Q PA TOP WRT/* Give the CE ARRIVE coord at T0P of pipeo Q PA BOP WRT/* Give the CE arrive coord at BOP of pipeo Q PH BORE Give the CE pipe head boreo Q PH OD Give the CE pipe head external diametero Q PI WRT/* Give the CE (PIPE SUPPT) locationo Q PL WRT/* Give the CE LEAVE coordinateso Q PT OD Give the Pipe tail Outside Diametero Q TPOS Give the pipe tail coordinateso Q CREF Give the connection referenceo Q PT Give the pipe tail attributeso Q ITLE Give the length of the implied tubeo CONN TO PREV Connect the CE to previous elemento CONN TO NEXT Connect the CE to next elemento FCONN TO PREV Force connection with incompatibles COCOo Q MTOT Give the MTO Status for the tubingo Q MTOC Give the MTO status for componento Q TULE Give the Branch tube lengtho Q MTLE Give Length of material tubeo Q MTLL Give CL. Length of material tubeo Q NCOF Give the CE net COGo Q NSRF Give the CE net surfaceo Q NVOL Give the CE net volumeo Q NWEI Give the net weighto Q SPRE Give the CE specification referenceo Q GCOF Give the CE gross Centre OF Gravityo Q GWEI Give the CE gross weighto Q MASS Give the centre of gravity and surface andvolumeo Q VOL CE Give the Volume box in coordinate ENUo Q WVOL Give the Volume box in coordinate ENU

o Q BANG Give the beta angle of the SCTNo Q DRNE Give the end cut plane directiono Q JUSL Give the justification lineo Q DTYPE Give the FRMW style type (ie STLS)o Q JLnV Give the CE JOINT LINEo Q DRNS Give the start cut plane directiono EXTEND TO ID@ Extend the sctn end to a selected itemo EXTEND TO IDP@ Extend the sctn end to a selected Ppointo EXTEND TO IDPL@ Extend the sctn end to a selected Plineoo NEW PANEL COPY PREV MOV TOWard ID@ DIST 100 COPY THEPANEL FROM ITS POSITION TOWARD ELEMTDISTANCE 100o Q IDPL@ give the Pline information using cursoro CALLSTL GSCTNTAG CE mark CE sctn START &ENDo DRNS PERP Cut the SCTN end AT 9ODEG to sectiono Q CUTLE Give the CE CUT LENGTHo Q HEI Give the CE (PLOO LVL) PLT THKo Q FRAD Give the PLOO/PAVE RADIUS ie 100mm ORthe NXTR/VERT radius ie 1OOmmo Q SJUS Give the PLOO justification ie UTOPo Q NCOF Give the CE net COGo Q NSRF Give the CE net surfaceo Q NVOL Give the CE net volumeo Q NWEI Give the CE NET weighto Q PLNA Give the CE PLINE NAMESo Q SPRE Give the CE specification referenceo Q GRADE Give the CE MATERIAL GRADEo Q GTYP Give the GENERIC TYPE ie OD,HP,TGo Q GCOF Give the CE gross Centre OF Gravityo Q GWEI Give the CE gross weighto Q MATREF Give the CE MATERIAL REPo Q DER LEN Give the CE exact length

o Q TCTL OR (Q CUTL) Give the TRUE cut length

EQUIPEMENTObject Connectiono CONN IDP@ to IDP@ Connection from idp to idpo CONN P2 to P3 OF PREV BOX Connection of P2 to P3 of previous boxo Q GCOF Give the gross centre of gravityo Q GWEI Give the gross weightPDMS TYPICAL COMMANDSATTRIBUT GENERALo AID CLEAR LINE ALL Remove all aid lineso AXES AT CE Place axe at CEo AXES AT PA CE Place axe at CE ppoint Parriveo AXES AT PPLI TOS PROP 1 Place axe at the end of TOS plineo AXES OFF Remove axeo CHECK CE Query the consistency of the ceo FINISH End & savework Pdms sessiono FLIP CE Turn 180 degrees the component itselfo GETWORK Get latest model from other usersINCLUDE (To use that command you MUST be on the right getting hierarchy)o INCLude CIRC 1 OF NOTE /TABLE Transfer with item full nameo INCLude ID@ Select the item to be transferredo INCLude NAME Include with by its name, you could use$V1o LOCK ALL Lock the CE & CE memberso NAME /TEMPORARY Rename CE TEMPORARYo NEW FITT COPY PREV BY ZDIST PROP 1 BANG 180 Copy the fitting atthe end of sctn and turn it 180°o PROP 0 = START POSITIONo PROP 0.5 = MIDDLE POSITIONo PROP 1 = END POSITIONoo RENAME ALL /xxx/XXX /xxx/YYY Rename all from /xxx/XXX to /yyy/YYYo SAVEWORK SAVE LATEST WORKo UNCLAIM ALL Unlock all claimed memeberso UNLOCK ALL Unlock CE & CE memberso FINISH Savework and Exit

and much more