riv-ti tubtara blind rivet nuts - titgemeyer gmbh 6 6 7 steel 8 8 4 4 4 5 stainless aluminium steel...
TRANSCRIPT
● thick walled for greater strength● chamfered for easy insertion● round, hex and raised spline bodies● flat, countersunk and slim heads
Riv
-Ti T
ubta
ra T
b136
9TU
K(1
005)
1
RIV-TI® TUBTARAblind rivet nuts
Fastening Technology
9
10
13
14
6
6
7
steel
8
8
4
4
4
5
stainless
aluminium
steel
aluminium
steel
brass
stainless
aluminium
steel
stainless
aluminium
steel
steel
steel
stainless
stainless
steel
stainless
steel
stainless
10
11
steel
18
19
steel 17
15
16
20
2
11
12
aluminium
steel
steel 23
22
24
21
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
RIV-TI®
blind rivet nuts
Round Body Flat Head Open End
Closed End
Countersunk Head
Slim Head
Open End
Closed End
Open End
Closed End
Part Hex Body Flat Head Open End
Slim Head Open End
Hexagon Body Flat Head Open End
Slim Head
Closed End
Raised Spline Round Body
Flat Head
Countersunk Head
Round Body Flat Head + Seal
Open End
Closed End
Open End
Open End
Closed End
RIV-TI® Blind Rivet Studs
3(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
RIV-TI®blind rivet nuts
VerastileRiv-Ti® rivet nuts are a combination of rivet and nut. You can fasten with it, to it - or both.
Riv-Ti® rivet nuts are perfect for use in high volume production or for prototypes. They are installed from one side of the application using simple and effective power or hand tools.
InstallationRiv-Ti® rivet nuts are easy and quick to install.They are energy efficient, produce no fumes and do not require the assembly to be cleaned after installation. They can be installed after components have been painted or otherwise coated without damaging the surface finish.
VarietyRiv-Ti® rivet nuts are available in aluminium, steel, brass and stainless steel with thread sizes fromM3 to M12 and can be installed in material from 0.25 mm to 8 mm thick.
They can have round, hexagonal or raised spline body shapes with flat, countersunk or slim head styles and open or closed ends.
Special parts are also possible depending on the quantity required. For example special parts can have underhead ribs, extra-large heads, extra-thick heads or stand-off heads to eliminate the need for spacers.
RIV-TI® Blind Rivet StudsRIV-TI® blind rivet nuts can be supplied to special order as rivet studs. Size range is from M4 to M8.Installation is basically the same as for rivet nuts except that the threaded mandrel on the installation tool is replaced with an internally threaded pulling bolt.
Screw the Riv-Ti®
rivet nut on to the threaded mandrel of the installation tool
Place the rivet nut into the pre-drilledor pre-punchedhole
Operate the tool to install the rivet nut securely in place
Spin the mandrel out of the rivet nut
The Riv-Ti® rivet nut is now readyfor use with a suitable screw or bolt
Aluminium
Steel, zinc and yellow passivate
Brass
1 No lead-in chamfer
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
Part NumberSteel Brass
336 223336 453
-
-
336 1811
336 1831
Aluminiumk
Diameterd
Diameter HeightSizeThread
d1
Grip Range Head
4
HoleDiameter
Body Length
L D
0.5 -3.0
s
2.0 - 3.0
0.5 - 2.0 9.8 336 3511
10.8 336 35310.85.1
336 493
3.0 - 4.5 12.3 336 455 336 225
0.5 - 3.0 10.8
-0.86.1
12.0 336 552 336 262 336 592
3.0 - 5.5 15.0 336 554 336 264
336 633 336 713
-
0.5 -3.0 14.5 336 631 336 711 336 671
1.07.1
-
5.5 - 8.0 19.0 336 634 336 714 -
1.59.13.0 - 5.5 16.5
336 817
3.0 - 5.5 18.5 336 773 336 859 -
0.5 -3.0 16.0 336 771 336 857
336 901 336 987
5.5 - 8.0 21.5 336 775 336 860
1.516.011.011.1
3.5 - 6.0 22.8 336 903 336 9892.318.512.412.5
0.8 - 3.5 19.8
0.8 - 3.5 21.0 - 336 988
- 336 011
3.5 - 6.0 24.0 - 336 9902.019.013.013.1
4.0 - 7.0 28.0 _ 336 0122.023.016.016.1
1.0 - 4.0 25.0
-
-
-
-
-
-
-
8.0
10.0
11.0
13.0
5.0
6.0
7.0
9.0
M8
M10
M10
M12
M3
M4
M5
M6
RIV-TI®blind rivet nuts
Flat headRound bodyOpen end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Stainless steel
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
5
d1
Part NumberStainless steel
334 225
334 226
kDiameter
dHeightSize
Thread Grip Range HeadDiameter
Body Length
0.5 - 3.0 11.5
HoleDiameter
7.1
5.0 -7.0
M8
3.0 - 5.0
D
2.0 - 3.5
0.5 - 2.0 11.0
12.56.06.1
Ls
334 266
334 2677.0
0.5 -3.0 14.5 334 716
10.0 1.03.0 - 5.0 15.0
334 717
18.5 -
1.5
1.53.0 - 5.5 18.5
16.0
M4
M5
334 856
1.09.0
0.5 -3.0 334 85511.1 11.0 15.0
M100.8 - 3.0
12.1 12.03.0 - 5.0
18.515.0 1.0
334 985
20.5 334 986
M6 9.1 9.0 12.016.5
RIV-TI®blind rivet nuts
Flat headRound bodyOpen end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Aluminium
Steel, zinc and yellow passivate
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
M8
M6
336 751 336 837
3.0 - 5.5 25.5 336 753 336 83911.0
22.516.0 1.5
336 611 336 691
336 613 336 69313.0 1.5
0.5 - 3.0
6.0 10.0 0.8
7.018.0
11.0336 532 336 242
6
M5
0.5 - 3.011.1
336 534 336 2443.0 - 5.57.1
Diameter
M40.5 - 3.0
3.0 - 4.56.1
HeightSizeThread
d1
Grip Range
s
HeadBody Hole Part Number
kDiameter
dDiameterLength
L DAluminium Steel
336 433
- 336 205
336 203
1.020.5
14.8
0.5 - 3.09.1 9.0
21.5
3.0 - 5.5 24.5
16.3
RIV-TI®blind rivet nuts
Flat headRound bodyClosed end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Stainless steel
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
Stainless steelHeadBody Part Number
kDiameter
dDiameterLength
L Dd1
Grip Range
s
7
23.5
HoleDiameter
21.5
HeightSizeThread
12.0 1.5 334 691M6 0.5 - 3.0 9.1 9.0
15.0 1.5 334 841M8 0.5 - 3.0 11.1 11.0
RIV-TI®blind rivet nuts
Flat headRound bodyClosed end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Aluminium
Steel, zinc and yellow passivate
1 No lead-in chamfer
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
1.54.0 - 6.5 16.0
1.7 - 4.59.1 9.0
17.012.0 1.5
4.5 - 6.5
336 231
336 563 336 273
6.1 6.0 9.0 1.5
7.1 7.013.0
Part Number
kDiameter
dDiameterLength
L DAluminium SteelHeightSize
Thread
d1
Grip Range
s
HeadBody HoleDiameter
M43.5 - 5.0 13.0
336 561 336 271
8
M5
1.7 - 4.511.1
336 465 336 235
10.0
336 641 336 721
19.0 336 642 336 722
336 781 336 867
4.5 - 6.5 21.0 336 782 336 86811.0
19.014.0 1.5M8
M6
M3 1.7 - 3.5
1.7 - 4.0
1.5 336 3611 336 1911
1.7 - 3.5
5.1 5.0 11.3 8.0
11.5 336 461
M101.7 - 4.5
12.5 12.4336 997
4.5 - 6.5 23.0 336 912 336 998
21.015.4 1.5
336 911
M122.0 - 4.5
16.1 16.0336 021
4.5 - 7.5 29.0 - 336 022
26.019.0 1.8
-
RIV-TI®blind rivet nuts
Countersunk headRound bodyOpen end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Stainless steel
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
9.0 1.0 334 276M5 1.2 - 3.5 7.1 7.0
8.0 1.0 334 236M4 1.2 - 3.0 6.1 6.0
9
12.0
HoleDiameter
12.0
HeightSizeThread
d1
Grip Range
s
HeadBody Part Number
kDiameter
dDiameterLength
L DStainless steel
M6 1.7 - 4.5 9.1 9.0 17.0 12.0 1.5 334 726
M81.7 - 4.5
11.1 11.04.5 - 6.5 19.5
334 865
334 864
17.514.0 1.5
M10 1.7 - 4.5 12.1 12.0 20.0 15.0 1.5 334 994
RIV-TI®blind rivet nuts
Countersunk headRound bodyOpen end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Aluminium
Steel, zinc and yellow passivate
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
1.54.0 - 6.5 20.5
1.7 - 4.59.1 9.0
22.012.0 1.5
4.5 - 6.5
336 251
336 2156.1 6.0 9.0 1.5
7.1 7.018.0
10.0
Thread
d1
Grip Range
s
11.1
15.5
HeightSizek
Diameterd
DiameterLengthL
M4
M5
1.7 - 3.5
3.5 - 5.0
1.7 - 4.0
HoleDiameter
HeadBody Part Number
D
336 701
24.0 336 622 336 702
Aluminium Steel
336 211
336 253
336 847
4.5 - 6.5 28.0 336 762 336 84811.0
25.014.0 1.5
1.7 - 4.5
10
M8
M6
336 441
336 445
336 541
336 543
336 761
336 621
17.0
RIV-TI®blind rivet nuts
Countersunk headRound bodyClosed end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Aluminium
Steel, zinc and yellow passivate
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
9.5 0.5335 473 335 293
335 474 335 2949.1 9.0
3.0 - 5.5 16.5
14.50.5 - 3.0
Part Number
kDiameter
dDiameterLength
L DHeight
HeadSizeThread
d1
Grip Range
s
Body
12.0
HoleDiameter
10.8
3.0 - 5.5 15.0
M6
6.5 0.5M4 0.5 - 3.0 6.1 6.0
0.5 - 3.0M5 7.1 7.0
Aluminium Steel
335 443 335 263
7.5 0.5335 453 335 283
- 335 284
M80.5 - 3.0
11.1 11.0335 303
3.0 - 5.5 18.5 - 335 304
16.011.5 0.5
335 483
M10 0.8 - 3.5 12.5 12.4 335 313
11
19.5 12.9 0.5 -
RIV-TI®blind rivet nuts
Slim headRound bodyOpen end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Stainless steel
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
334 304
12
HoleDiameter
HeadBody
0.5 - 3.0M5
M6 0.5 - 3.0
Part Number
DLength
L
0.5 - 2.0
7.1
Stainless steel
334 260M4
Thread
d1
Grip Range
sSize
7.0 12.0 7.5
0.5
Heightk
Diameterd
Diameter
6.1 6.0 11.0 6.5
14.59.1 9.0 9.5
16.011.5 0.5
3.0 - 5.5 18.5M8
0.5 - 3.011.1 11.0
334 303
0.5
0.5 334 293
334 283
RIV-TI®blind rivet nuts
Slim headRound bodyOpen end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Steel, zinc and yellow passivate
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
13
335 242
7.5 0.5
9.5 0.5
6.5 0.5
335 252
335 276
7.1 7.0
M6 9.1 9.0
M4 0.5 - 3.0 6.1 6.0
18.0
HoleDiameter
15.0
0.5 - 3.0 21.5
0.5 - 3.0M5
HeightSizeThread
d1
Grip Range
s
HeadBody Part Number
kDiameter
dDiameterLength
L DSteel
335 306M8 0.5 - 3.0 11.1 11.0 11.5 0.522.5
RIV-TI®blind rivet nuts
Slim headRound bodyClosed end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Stainless steel
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
0.5
0.5
9.1
Stainless steel
334 383
334 393
Heightk
DiameterThread
d1
Grip Range
sSize
Part Number
D
0.5 - 3.0M6
DiameterLengthL
9.0 21.5 9.5
14
M5 0.5 - 3.0 7.1 7.0 18.0 7.5
Hole HeadBody Diameter
d
RIV-TI®blind rivet nuts
Slim headRound bodyClosed end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Stainless steel
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
15.0 1.516.0M8 0.5 - 3.0 11.1 11.0
A/FSW
DiameterLengthL D
HeightSizeThread
d1
Grip Range
s
HeadBody
k
11.5
HoleA/F
11.0
0.5 - 3.0 14.5
0.5 - 3.0M5
9.0 1.0M4 0.5 - 2.0 6.1 6.0
7.1 7.0
M6 9.1 9.0
10.0 1.0
12.0 1.5
15
Part NumberStainless steel
334 135
334 155
334 175
334 185
RIV-TI®blind rivet nuts
Flat headPart Hex bodyOpen end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Stainless steel
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
Part Number
SW1
16
M4 0.5 - 2.0 6.1 6.0 11.0 6.5
HoleA/F
HeadBody A/FLength
L
Thread
d1
Grip Range
sSize
SW
7.0 12.0 7.5M5
0.5
7.1
Stainless steel
334 142
334 162
Heightk
A/F
0.5
0.5 - 3.0 14.5
0.5 - 3.0
0.5 - 7.0
M6 9.1 9.03.0 - 5.0
18.5 -
9.5 0.5
334 182
16.5 334 183
M8 0.5 - 3.0 11.1 11.0 16.0 11.5 0.5 334 192
RIV-TI®blind rivet nuts
Slim headPart Hex bodyOpen end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Steel, zinc and yellow passivate
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
16.5
SWDiameterLength
L D
9.0
10.0
HeightSizeThread
d1
Grip Range
s
HeadBody
k
13.0
HoleA/F
10.0
14.5
0.5 - 3.0M5
A/F
1.0M4 0.5 - 2.0 6.1 6.0
7.1 7.0
M60.5 - 3.0
9.1 9.03.0 - 5.5
1.0
13.0 1.5
17
339 262
339 711
339 713
Part NumberSteel
339 222
M80.5 - 3.0
11.1 11.03.0 - 5.5
16.516.0 1.5
339 857
19.0 339 859
M100.8 - 3.5
13.1 13.03.5 - 6.0
21.019.0 2.0
339 987
23.5 339 989
M12 1.0 - 4.0 16.1 16.0 25.0 23.0 2.0 339 998
RIV-TI®blind rivet nuts
Flat headHexagon bodyOpen end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Steel, zinc and yellow passivate
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
27.0 339 838
M10 0.8 - 3.5 13.1 13.0 31.0 19.0 2.0 339 970
339 693
M80.5 - 3.0
11.1 11.03.0 - 5.5
24.516.0 1.5
339 837
Part Number
D
18
M4 0.5 - 2.0 6.1 6.0 14.5 9.0
HoleA/F
HeadBody DiameterLength
LHeight
kA/F
Thread
d1
Grip Range
sSize
1.0
19.0
SWSteel
339 202
339 243
21.5
21.510.0 1.0
339 242
13.0 1.5339 691
23.5M6 9.1 9.0
M5 7.13.0 - 5.5
7.0
0.5 - 3.0
0.5 - 3.0
3.0 - 5.5
RIV-TI®blind rivet nuts
Flat headHexagon bodyClosed end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Steel, zinc and yellow passivate
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
M6 9.1 9.0
A/FLengthL SW1
11.00.5 - 2.0 6.1
HeightSizeThread
d1
Grip Range
s
HeadBody
k
14.0
HoleA/F A/F
SW
16.00.5 - 3.0
M4 6.0
M50.5 - 3.0
7.1 7.03.0 - 5.5 16.5
19
Part NumberSteel
7.7 0.6
6.6 0.6
0.7
3.0 - 5.5 18.59.8 0.7
M80.5 - 3.0
11.1 11.03.0 - 5.5 20.5
18.011.8
23.0 13.8 0.7M10 0.8 - 3.5 13.1 13.0
339 812
339 957
339 959
339 991
339 322
339 362
339 363
339 811
RIV-TI®blind rivet nuts
Slim headHexagon bodyOpen end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Steel, zinc and yellow passivate
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
M8 0.5 - 3.0 11.1 11.0
M6 0.5 - 3.0 9.1 9.0 339 911
25.0 339 967
22.0 9.8 0.7
11.8 0.7
339 4620.70.5 - 3.0M5 7.1 7.0 20.0 7.7
SWSteel
339 4220.6
Thread
d1
Grip Range
sSize A/F
HeadBody A/FLength
LHeight
kA/F
Part Number
SW1
20
M4 0.5 - 2.0 6.1 6.0 15.5 6.6
Hole
RIV-TI®blind rivet nuts
Slim headHexagon bodyClosed end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Steel, zinc and yellow passivate
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
19.818.5 2.2
337 920
22.8 337 921M10
0.8 - 3.513.0 12.9
3.5 - 6.0
11.416.0
16.0 1.518.5
14.513.0 1.5
337 910
16.5 337 911
M4 6.4 6.3
M60.5 - 3.0
9.4 9.33.0 - 5.5
7.3
DiameterLengthL D
HeightSizeThread
d1
Grip Range
s
HeadBody
k
HoleDiameter
3.0 - 4.5
M50.5 - 3.0
7.43.0 - 5.5
3.0 - 5.5
Diameterd
10.80.5 - 3.0
21
Part NumberSteel
337 9000.8
1.015.0
12.011.0
M80.5 - 3.0
11.5
337 901
337 905
337 906
337 916
337 915
12.310.0
RIV-TI®blind rivet nuts
Flat headRaised spline round bodyOpen end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Steel, zinc and yellow passivate
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
19.014.0
1.5
337 945
1.5337 950
337 951
6.4 6.311.5
9.013.0
337 946
21.015.4
4.5 - 6.51.5
21.0
4.5 - 6.5 23.012.9
11.4
M101.7 - 4.5
13.0
M81.7 - 4.5
11.5
337 940
19.0 337 941M6
1.7 - 4.59.4 9.3
4.5 - 6.5
17.012.0
1.7 - 4.07.4 7.3
13.0
16.04.0 - 6.510.0
1.5337 930
337 931
1.5337 936
Part Number
D
22
1.7 - 3.5
HoleDiameter
HeadBody DiameterLength
L
Thread
d1
Grip Range
sSize
M5
Steel
3.5 - 5.0
337 935
M4
Heightk
Diameterd
RIV-TI®blind rivet nuts
Countersunk headRaised spline round bodyOpen end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
Steel, zinc and yellow passivate
Seal - black silicon-free NBR70
Seal totally enclosed - gas and fluid tight
Great resistance to turning
Inner and outer parts of head are in contact with the application;this prevents deformation of the application especially in thin materials
Temperature range: - 40 C to + 80 C continuous- 40 C to + 190 C for 30 minutes maximum
Dimensions are in mm and nominal unless stated
We reserve the right to amend specifications at any time
M5
d1
0.5 - 3.0
M6 0.5 - 3.0
7.1
M8 0.5 - 1.5
D
HoleHeightSize
Thread Grip Range HeadBody DiameterLength
s LA/FSW
A/F
1.5
1.5
Part NumberSteel
339 245
k
9.1
23
339 69515.0
2.0 339 850
12.5
9.0 21.5
7.0 19.0
11.1 11.0 24.5 20.0
RIV-TI®blind rivet nuts with seal
Flat head with sealHexagon bodyClosed end
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
M12 - 82.0 -
M10 27.0 48.0 -
M8 17.0 24.0 24.0
M6 8.0 10.0 10.0
M5 4.5 6.0 6.0
M4 2.0 3.0 3.0
M3 1.0 1.2 -
Thread Aluminium Steel Stainless
Maximum Tightening Torque Nm
Thread Pull Out Strength N
M12 - 75000 -
M10 17500 31000 -
18000
M8 13500 25000 25000
7000
M5 5500 9000 9000
Stainless
M3 3000 5000 -
24
Thread Aluminium Steel
M4 4000 7000
M6 10000 18000
RIV-TI®blind rivet nuts
Technical InformationThe figures given are typical test values for guidance only and not to be used as specifications.
Users must satisfy themselves as to the performance of RIV-TI® rivet nuts in their own application.
Titgemeyer application engineers will be happy to advise.
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
25
RIV-TI® blind rivet nuts INSTALLATION TOOLS
HAND TOOL MS 3For installation of blind rivet nuts
RangeM3 - M5 aluminium or steel
HAND TOOL R1For installation of blind rivet nuts
RangeM4 - M10 aluminium or steelM4 - M6 stainless steel
HAND TOOL MS 7For installation of blind rivet nutsand blind rivet studs
RangeM3 - M6 aluminiumM4 - M5 steelM4 - M5 blind rivet studs
HAND TOOL MS 9For installation of blind rivet nutsand blind rivet studs
RangeM4 - M10M4 - M8 blind rivet studs
POWER TOOL MS 50Hydro-pneumaticFor installation of blind rivet nutsand blind rivet studs
RangeM3 - M10M4 - M8 blind rivet studs
POWER TOOL MS 100Hydro-pneumaticFor installation of blind rivet nuts and blind rivet studs
RangeM8 - M14
FIREBIRD® BATTERY TOOL For installation of blind rivet nuts
RangeM3 - M10 aluminiumM3 - M8 steel
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
26
RIV-TI®blind rivet nuts
InstallationThe key to correct installation is to use the correct part and to produce the correct upset. Set the installation tool according to instructions supplied and check in-situ or using scrap material of the correct total thickness. The correct upset form is shown opposite. When satisfied, lock the tool setting and proceed.
Fig 2Fig 1
To avoid damaging the Riv-Ti® rivet nut threads the tool mandrel must engage all the threads in the rivet nut - see Fig. 1. Ensure one or two threads of the mandrel protrude through the end of the Riv-Ti® rivet nut - see Fig. 2. The tool must be held at right angles to the workpiece.
When installing countersunk head Riv-Ti® rivet nuts do not countersink the material too deep. Always ensure that the tool anvil is the same diameter or slightly smaller then the Riv-Ti® head to avoid ‘bridging’ the hole and causing a loose upset. For optimum performance the head of the Riv-Ti® should be approximately 0.1 mm proud of the surface after installation.
Grip RangeMeasure the total material thickness including paint, burrs, etc. and select a Riv-Ti® with suitable grip range. If the total material thickness is at the upper limit of the grip range, select a longer part. If in doubt ask for advice.
The illustrations show typical installations.
Upset too much
Upset correct
Upset too little
Flat headplain hole
Countersunk headcountersunk hole
Countersunk headdimple countersunk
hole
(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
27(UK) LTD - Tel.:+44(0)121-557-9777 - Fax:+44 (0)121-557-4777 - [email protected] - www.titgemeyer.co.uk
TITGEMEYER (UK) LtdA2 Link One Industrial Park - George Henry RoadTipton - West Midlands - DY4 7BUUnited KingdomTel. +44(0)121-557-9777Fax +44(0)[email protected]
Blind Rivets
Threaded Inserts
Assembly Systems
Installation Tools