pcm175x 24-bit 192-khz sampling enhanced multi-level …pcm175x 24-bit 192-khz sampling enhanced...
TRANSCRIPT
Enhanced Multilevel
Delta-Sigma Modulator
Power Supply
DG
ND
VOUTL
4x/8x Oversampling Digital Filterand Function
Control
AudioSerialPort
BCK
LRCK
DATAOutput Amp
AndLow-Pass Filter
SystemClock Manager
TEST
SCKZero Detect
MUTE
FMT
SerialControl
Port
DEMP
DAC
VCOM
System C lock
AG
ND
VC
C
ZE
RO
A
Output AmpAnd
Low-Pass FilterDAC
VOUTR
Product
Folder
Sample &Buy
Technical
Documents
Tools &
Software
Support &Community
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015
PCM175x 24-Bit 192-kHz Sampling Enhanced Multi-Level Delta-Sigma Audio Digital-to-Analog Converter
1 Features 3 DescriptionThe PCM175x devices are stereo digital-to-analog
1• 24-Bit Resolutionconverters (DACs) based on TI's enhanced delta-• Analog Performance (VCC = 5 V) sigma architecture which employ 4th-order noise
– Dynamic Range: 106 dB shaping and 8-level amplitude quantization to achieveexcellent dynamic performance and improved clock– SNR: 106 dB, Typicaljitter tolerance. The PCM175x devices easily interface– THD+N: 0.002%, Typical with audio DSP and decoder chips because of the
– Full-Scale Output: 4 VPP, Typical devices' support of industry-standard audio dataformats with 16- and 24-bit data. The PCM175x• 4×/8× Oversampling Digital Filterdevices can be controlled in a hardware mode, or a– Stop-Band Attenuation: –50 dB full set of user-programmable functions is accessible
– Pass-Band Ripple: ±0.04 dB through a three-wire serial control port, which• Sampling Frequency: 5 kHz to 200 kHz supports register-write functions.• System Clock: 128 fS, 192 fS, 256 fS, 384 fS, 512 The PCM1753 is pin-compatible with the PCM1748,
fS, 768 fS, 1152 fS with Auto Detect PCM1742, and PCM1741, except for pin 5.• Hardware Control (PCM1754)
Device Information(1)– I2S and 16-Bit Word, Right-Justified
PART NUMBER PACKAGE BODY SIZE (NOM)– 44.1 kHz Digital De-EmphasisPCM1753
– Soft MutePCM1754 SSOP (16) 3.90 mm × 4.90 mm
– Zero Flag for L-, R-Channel Common Output PCM1755• Power Supply: 5-V Single Supply
(1) For all available packages, see the orderable addendum at• Small 16-Lead SSOP Package, Lead-Free the end of the data sheet.
2 Applications• A/V Receivers• HDTV Receivers• Car Audio Systems• Other Applications Requiring 24-Bit Audio
Functional Block Diagram
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,intellectual property matters and other important disclaimers. PRODUCTION DATA.
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
Table of Contents8.3 Feature Description................................................. 121 Features .................................................................. 18.4 Device Functional Modes........................................ 172 Applications ........................................................... 18.5 Programming........................................................... 183 Description ............................................................. 18.6 Register Maps ......................................................... 194 Revision History..................................................... 2
9 Application and Implementation ........................ 245 Device Comparison Table ..................................... 39.1 Application Information............................................ 246 Pin Configuration and Functions ......................... 39.2 Typical Application ................................................. 247 Specifications......................................................... 4 10 Power Supply Recommendations ..................... 297.1 Absolute Maximum Ratings ...................................... 4
11 Layout................................................................... 297.2 ESD Ratings.............................................................. 411.1 Layout Guidelines ................................................. 297.3 Recommended Operating Conditions...................... 411.2 Layout Example .................................................... 297.4 Thermal Information .................................................. 4
12 Device and Documentation Support ................. 317.5 Electrical Characteristics........................................... 512.1 Related Documentation ....................................... 317.6 System Clock Input Timing ....................................... 612.2 Related Links ........................................................ 317.7 Audio Interface Timing .............................................. 612.3 Community Resources.......................................... 317.8 Control Interface Timing Requirements .................... 712.4 Trademarks ........................................................... 317.9 Typical Characteristics .............................................. 812.5 Electrostatic Discharge Caution............................ 318 Detailed Description ............................................ 1212.6 Glossary ................................................................ 318.1 Overview ................................................................. 12
13 Mechanical, Packaging, and Orderable8.2 Functional Block Diagram ....................................... 12Information ........................................................... 31
4 Revision HistoryNOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision C (February 2009) to Revision D Page
• Added ESD Ratings table, Recommended Operating Conditions table,Feature Description section, DeviceFunctional Modes, Application and Implementation section, Power Supply Recommendations section, Layoutsection, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section. ..... 1
2 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
SCK
FMT
MUTE
DEMP
TEST
ZEROA
VCOM
15
14
13
12
11
10
DATA
LRCK
DGND
NC
VCC
V LOUT
1
2
3
4
5
6
7
8
16
9
BCK
AGNDV ROUT
SCK
ML
MC
MD
ZEROL/NA
ZEROR/ZEROA
VCOM
15
14
13
12
11
10
DATA
LRCK
DGND
NC
VCC
V LOUT
1
2
3
4
5
6
7
8
16
9
BCK
AGNDV ROUT
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
5 Device Comparison Table
FEATURE PCM1753-Q1 PCM1754-Q1Audio-data interface format I2S, standard, left-justified I2S, standard
Audio-data bit length 16-bit, 18-bit, 20-bit, and 24-bit selectable 16-bit and 24-bit I2S, 16-bit standardAudio data format MSB first, 2s complement
6 Pin Configuration and Functions
PCM1753, PCM1755 DBQ Package PCM1754 DBQ Package16-Pin SSOP 16-Pin SSOP
Top View Top View
Table 1. Pin FunctionsPIN
I/O DESCRIPTIONPCM1753/NAME PCM175455AGND 9 9 — Analog groundBCK 1 1 I Audio-data bit-clock inputDATA 2 2 I Audio-data digital inputDEMP - 13 I De-emphasis controlDGND 4 4 — Digital groundFMT - 15 I Data format selectLRCK 3 3 I L-channel and R-channel audio data latch enable inputMC 14 - I Mode control clock inputMD 13 - I Mode control data inputML 15 - I Mode control latch inputMUTE - 14 I Analog mixing controlNC 5 5 — No connectionSCK 16 16 I System clock inputTEST - 12 I Test pin. Ground or openVCC 6 6 — Analog power supply, 5 VVCOM 10 10 — Common voltage decouplingVOUTL 7 7 O Analog output for L-channelVOUTR 8 8 O Analog output for R-channelZEROR/ZEROA 11 11 O Zero flag output for R-channel/Zero flag output for L-/R-channelZEROL/NA 12 - O Zero flag output for L-channel/Not assigned
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: PCM1753 PCM1754 PCM1755
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)MIN MAX UNIT
Supply voltage VCC –0.3 6.5 VGround voltage differences AGND, DGND ±0.1 VInput voltage –0.3 6.5 VInput current (any pins except supplies) ±10 mAAmbient temperature under bias –40 85 °CJunction temperature 150 °CStorage temperature, Tstg –55 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratingsonly, and functional operation of the device at these or any other conditions beyond those indicated is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
7.2 ESD RatingsVALUE UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) ±2000V(ESD) Electrostatic discharge VCharged-device model (CDM), per JEDEC specification JESD22- ±750C101 (2)
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditionsover operating free-air temperature range (unless otherwise noted)
MIN NOM MAX UNITVCC Voltage range 4.5 5 5.5 V
7.4 Thermal InformationPCM175x
THERMAL METRIC (1) DBQ (SSOP) UNIT16 PINS
RθJA Junction-to-ambient thermal resistance 104.1 °C/WRθJC(top) Junction-to-case (top) thermal resistance 53 °C/WRθJB Junction-to-board thermal resistance 46.9 °C/WψJT Junction-to-top characterization parameter 10.3 °C/WψJB Junction-to-board characterization parameter 46.4 °C/WRθJC(bot) Junction-to-case (bottom) thermal resistance N/A °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics applicationreport, SPRA953.
4 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
7.5 Electrical CharacteristicsAll specifications at TA = 25°C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS, and 24-bit data (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNITResolution 24 Bits
DATA FORMATfS Sampling frequency 5 200 kHz
128 fS192 fS256 fS
System clock frequency 384 fS kHz512 fS768 fS1152 fS
DIGITAL INPUT/OUTPUTLogic family TTL compatible
VIH Input logic level, high 2 VDCVIL Input logic level, low 0.8 VDC
Input logic current, high (SCK, BCK, DATA,IIH VIN = VCC 10 µAand LRCK pins)Input logic current, low (SCK, BCK, DATA,IIL VIN = 0 V -10 µAand LRCK pins)Input logic current, high (TEST, DEMP,IIH VIN = VCC 65 100 µAMUTE, and FMT pins)Input logic current, low (TEST, DEMP,IIL VIN = 0 V -10 µAMUTE, and FMT pins)
VOH Output logic level, high (ZEROA pin) IOH = -1 mA 2.4 VDCVOL Output logic level, low (ZEROA pin) IOL = 1 mA 0.4 VDCDYNAMIC PERFORMANCE (1) (2)
fS = 44.1 kHz 0% 0.01%THD+N at VOUT = 0 dB fS = 96 kHz 0%
fS = 192 kHz 0%fS = 44.1 kHz 0.65%
THD+N at VOUT = -60 dB fS = 96 kHz 0.80%fS = 192 kHz 0.95%EIAJ, A-weighted, fS = 44.1 kHz 100 106
Dynamic range A-weighted, fS = 96 kHz 104 dBA-weighted, fS = 192 kHz 102EIAJ, A-weighted, fS = 44.1 kHz 100 106
Signal-to-noise ratio A-weighted, fS = 96 kHz 104 dBA-weighted, fS = 192 kHz 102fS = 44.1 kHz 97 103
Channel separation fS = 96 kHz 101 dBfS = 192 kHz 100
Level linearity error VOUT = -90 dB ±0.5 dBDC ACCURACY
% ofGain error ±1 ±6 FSR% ofGain mismatch, channel-to-channel ±1 ±3 FSR
Bipolar zero error VOUT = 0.5 VCC at BPZ ±30 ±60 mV
(1) Analog performance specifications are measured using the System Two™ Cascade audio measurement system by Audio Precision™ inthe averaging mode.
(2) Conditions in 192-kHz operation are system clock = 128 fS and oversampling rate = 64 fS of register 18.
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: PCM1753 PCM1754 PCM1755
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
Electrical Characteristics (continued)All specifications at TA = 25°C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS, and 24-bit data (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNITANALOG OUTPUT
Output voltage Full scale (0 dB) 80% of VCC VPP
Center voltage 50% of VCC VDCLoad impedance AC-coupled load 5 kΩ
DIGITAL FILTER PERFORMANCEFILTER CHARACTERISTICS (SHARP ROLLOFF)
Pass band ±0.04 dB 0.454 fSStop band 0.546 fsPass-band ripple ±0.04 dBStop-band attenuation Stop band = 0.546 fS -50 dB
ANALOG FILTER PERFORMANCEAt 20 kHz -0.03
Frequency response dBAt 44 kHz -0.2
POWER SUPPLY REQUIREMENTS (2)
VCC Voltage range 4.5 5 5.5 VDCfS = 44.1 kHz 16 21
ICC Supply current fS = 96 kHz 25 mAfS = 192 kHz 30fS = 44.1 kHz 80 105
Power dissipation fS = 96 kHz 125 mWfS = 192 kHz 150
TEMPERATURE RANGEOperation temperature -40 105 °C
RθJA Thermal Resistance 16-pin DBQ 104.1 °C/W
7.6 System Clock Input TimingFor more information, see the System Clock Input section.
MIN NOM MAX UNITt(SCKH) System clock pulse duration, high 7 nst(SCKL) System clock pulse duration, low See Figure 20. 7 nst(SCY) System clock pulse cycle time See (1) ns
(1) 1/128 fS, 1/256 fS, 1/384 fS, 1/512 fS, 1/768 fS, or 1/1152 fS
7.7 Audio Interface TimingFor more information, see the Audio Data Formats and Timing section.
MIN MAX UNIT1/(32 fS)
t(BCY) BCK pulse cycle time 1/(48 fS)1/(64 fS) (1)
t(BCH) BCK high–level time 35 nst(BCL) BCK low–level time 35 ns
See Figure 22.t(BL) BCK rising edge to LRCK edge 10 nsLRCK falling edge to BCK risingt(LB) 10 nsedge
t(DS) DATA setup time 10 nst(DH) DATA hold time 10 ns
(1) fS is the sampling frequency (e.g., 44.1 kHz, 48 kHz, 96 kHz, etc.).
6 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
ML
MC
MD
t(MDS)
t(MCY)
t(MDH)
t(MCH)
t(MLS)t(MCL)
LSB
t(MLH)
t(MHH)
S
3
256 f´(1) seconds (min); fS: sampling rate.
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
7.8 Control Interface Timing RequirementsThese timing parameters are critical for proper control port operation.
MIN NOM MAX UNITt(MCY) MC pulse cycle time 100 nst(MCL) MC low-level time 50 nst(MCH) MC high-level time 50 nst(MCH) ML high-level time See (1) ns
See Figure 1.t(MLS) ML falling edge to MC rising edge 20 nst(MLH) ML hold time (2) 20 nst(MDH) MD hold time 15 nst(MCS) MD setup time 20 ns
(2) MC rising edge for LSB to ML rising edge.
Figure 1. Control Interface Timing
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: PCM1753 PCM1754 PCM1755
–10
–9
–8
–7
–6
–5
–4
–3
2
–1
0
0 2 4 6 8 10 12 14
Frequency (kHz)
De
-em
ph
asis
Le
ve
l (d
B)
–
Frequency (kHz)
–0.5
–0.4
–0.3
–0.2
–0.1
0.0
0.1
0.2
0.3
0.4
0.5
De
-em
ph
asis
Err
or
(dB
)
0 2 4 6 8 10 12 14
Frequency [× fS]
–140
–120
–100
–80
–60
–40
–20
0
0 1 2 3 4
Am
plit
ude
(dB
)
Frequency [× fS]
–5
–4
–3
–2
–1
0
1
2
3
4
5
0.0 0.1 0.2 0.3 0.4 0.5
Am
plit
ude (
dB
)
Frequency [× fS]
–140
–120
–100
–80
–60
–40
–20
0
0 1 2 3 4
Am
plit
ude
(dB
)
Frequency [× fS]
–0.05
–0.04
–0.03
–0.02
–0.01
0.00
0.01
0.02
0.03
0.04
0.05
0.0 0.1 0.2 0.3 0.4 0.5
Am
plit
ude
(dB
)
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
7.9 Typical Characteristics
7.9.1 Digital Filter (De-Emphasis Off)All specifications at TA = 25°C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS, and 24-bit data, (unless otherwise noted)
Figure 2. Frequency Response, Sharp Rolloff Figure 3. Pass-Band Ripple, Sharp Rolloff
Figure 4. Frequency Response, Slow Rolloff Figure 5. Transition Characteristics, Slow Rolloff
Figure 6. De-Emphasis Level vs Frequency Figure 7. De-Emphasis Error vs Frequency
8 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
Frequency (kHz)
–10
9
–8
–7
–6
–5
–4
–3
–2
–1
0
De-e
mphasis
Level (d
B)
0 2 4 6 8 10 12 14 16 18 20 22
–
Frequency (kHz)
–0.5
–0.4
–0.3
–0.2
–0.1
0.0
0.1
0.2
0.3
0.4
0.5
De-e
mphasis
Err
or
(dB
)
0 2 4 6 8 10 12 14 16 18 20 22
Frequency (kHz)
–10
–9
–8
–7
–6
–5
–4
–3
–2
–1
0
0 2 4 6 8 10 12 14 16
De
-em
ph
asis
Le
ve
l (d
B)
18 20
Frequency (kHz)
–0.5
–0.4
–0.3
–0.2
–0.1
0.0
0.1
0.2
0.3
0.4
0.5
De-e
mphasis
Err
or
(dB
)
0 2 4 6 8 10 12 14 16 18 20
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
Digital Filter (De-Emphasis Off) (continued)All specifications at TA = 25°C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS, and 24-bit data, (unless otherwise noted)
Figure 8. De-Emphasis Level vs Frequency Figure 9. De-Emphasis Error vs Frequency
Figure 10. De-Emphasis Level vs Frequency Figure 11. De-Emphasis Error vs Frequency
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: PCM1753 PCM1754 PCM1755
Supply Voltage (V)
96
98
100
102
104
106
108
110
Sig
nal-to
-Nois
e R
atio
(dB
)
4.0 4.5 5.0 5.5 6.0
192 kHz, 128 fS
S96 kHz, 384 f
44.1 kHz, 384 fS
Supply Voltage (V)
96
98
100
102
104
106
108
110
Channel S
epara
tion
(dB
)
4.0 4.5 5.0 5.5 6.0
192 kHz, 128 fS
S96 kHz, 384 f
44.1 kHz, 384 fS
4.0
Supply Voltage (V)
10
0.1
0.01
0.001
0.0001
Tota
l H
arm
onic
Dis
tort
ion +
Nois
e (
%)
1 –60 dB
0 dB
4.5 5.0 5.5 6.0
192 kHz, 128 fS
S96 kHz, 384 f
44.1 kHz, 384 fS
Supply Voltage (V)
96
98
100
102
104
106
108
110
Dynam
ic R
ange (
dB
)
4.0 4.5 5.0 5.5 6.0
192 kHz, 128 fS
S96 kHz, 384 f
44.1 kHz, 384 fS
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
7.9.2 Analog Dynamic Performance (Supply Voltage Characteristics)All specifications at TA = 25°C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS, and 24-bit data, (unless otherwise noted)
Figure 12. Total Harmonic Distortion + Noise vs Supply Figure 13. Dynamic Range vs Supply VoltageVoltage
Figure 14. Signal-to-Noise Ratio vs Supply Voltage Figure 15. Channel Separation vs Supply Voltage
10 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
Free-Air Temperature (°C)
96
98
100
102
104
106
108
110
Sig
nal-to
-Nois
e R
atio
(dB
)
–50 –25 0 25 50 75 100
192 kHz, 128 fS
S96 kHz, 384 f
44.1 kHz, 384 fS
Free-Air Temperature (°C)
96
98
100
102
104
106
108
110
Channel S
epara
tion
(dB
)
–50 –25 0 25 50 75 100
192 kHz, 128 fS
S96 kHz, 384 f
44.1 kHz, 384 fS
10
0.1
0.01
0.001
0.0001
Tota
l H
arm
onic
Dis
tort
ion
+ N
ois
e (
%)
1–60 dB
0 dB
Free-Air Temperature (°C)
–50 –25 0 25 50 75 100
192 kHz, 128 fS
S96 kHz, 384 f
44.1 kHz, 384 fS
Free-Air Temperature (°C)
96
98
100
102
104
106
108
110
Dynam
ic R
ange
(dB
)
–50 –25 0 25 50 75 100
192 kHz, 128 fS
S96 kHz, 384 f
44.1 kHz, 384 fS
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
7.9.3 Analog Dynamic Performance (Temperature Characteristics)All specifications at TA = 25°C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS, and 24-bit data, (unless otherwise noted)
Figure 16. Total Harmonic Distortion + Noise vs Free-Air Figure 17. Dynamic Range vs Free-Air TemperatureTemperature
Figure 18. Signal-to-Noise Ratio vs Free-Air Temperature Figure 19. Channel Separation vs Free-Air Temperature
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: PCM1753 PCM1754 PCM1755
Power Supply
DG
ND
Multilevel
Delta-Sigma
Modulator
VOUTL
4x/8x
Oversampling
Digital
Filter
and
Function
Control
Audio
Serial
Port
BCK
LRCK
DATA
Serial
Control
Port
Zero Detect
TEST
SCK System
Clock
Manager
MUTE
FMT
Output Amp
and
Low-Pass Filter
DEMP
DAC
VCOM
System Clock
AG
ND
VC
C
ZE
RO
A
Output Amp
and
Low-Pass Filter
DAC
VOUTR
Enhanced
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
8 Detailed Description
8.1 OverviewThe PCM175x devices are stereo digital-to-analog converters (DACs) based on TI's enhanced delta-sigmaarchitecture which employ 4th-order noise shaping and 8-level amplitude quantization to achieve excellentdynamic performance and improved clock jitter tolerance. The PCM175x devices easily interface with audio DSPand decoder chips because of the devices' support of industry-standard audio data formats with 16- and 24-bitdata. The PCM175x devices can be controlled in a hardware mode, or a full set of user-programmable functionsis accessible through a three-wire serial control port, which supports register-write functions.
8.2 Functional Block Diagram
8.3 Feature Description
8.3.1 System Clock and Reset Functions
8.3.1.1 System Clock InputThe PCM175x devices require a system clock for operating the digital interpolation filters and multilevel delta-sigma modulators. The system clock is applied at the SCK input (pin 16). Table 2 lists examples of system clockfrequencies for common audio sampling rates.
Figure 20 shows and the System Clock Input Timing table lists he timing requirements for the system clock input.For optimal performance, use a clock source with low phase-jitter and noise. TI's PLL170x family of multiclockgenerators is an excellent choice for providing the PCM175x system clock.
12 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
Reset Reset Removal
1024 System Clocks
VCC
3.7 V (Max)
3.0 V (Typ)
2.2 V (Min)
Internal Reset
System Clock
Don’t Care
t(SCKH)
t(SCY)
System Clock (SCK)
t(SCKL)
2.0 V
0.8 V
H
L
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
Feature Description (continued)Table 2. System Clock Rates for Common Audio Sampling Frequencies
SYSTEM CLOCK FREQUENCY (fSCLK) (MHz)SAMPLINGFREQUENCY 128 fS 192 fS 256 fS 384 fS 512 fS 768 fS 1152 fS
8 kHz 1.024 1.536 2.048 3.072 4.096 6.144 9.21616 kHz 2.048 3.072 4.096 6.144 8.192 12.288 18.43232 kHz 4.096 6.144 8.192 12.288 16.384 24.576 36.864
44.1 kHz 5.6448 8.4672 11.2896 16.9344 22.5792 33.8688 (1)
48 kHz 6.144 9.216 12.288 18.432 24.576 36.864 (1)
88.2 kHz 11.2896 16.9344 22.5792 33.8688 45.1584 (1) (1)
96 kHz 12.288 18.432 24.576 36.864 49.152 (1) (1)
192 kHz 24.576 36.864 (1) (1) (1) (1) (1)
(1) This system clock rate is not supported for the given sampling frequency.
Figure 20. System Clock Input Timing
8.3.1.2 Power-On Reset FunctionsThe PCM175x devices include a power-on reset function. Figure 21 shows the operation of this function. With thesystem clock active and VCC > 3 V (typical, 2.2 V to 3.7 V), the power-on reset function is enabled. Theinitialization sequence requires 1024 system clocks from the time VCC > 3 V (typical, 2.2 V to 3.7 V).
During the reset period (1024 system clocks), the analog output is forced to the bipolar zero level, or VCC/2. Afterthe reset period, an internal register is initialized in the next 1/fS period and if SCK, BCK, and LRCK are providedcontinuously, the PCM175x devices provide proper analog output with unit group delay against the input data.
Figure 21. Power-On Reset Timing
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: PCM1753 PCM1754 PCM1755
DATA
t(BCH)
1.4 V
BCK
LRCK
t(BCL) t(LB)
t(BCY)
t(DS) t(DH)
1.4 V
1.4 V
t(BL)
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
8.3.2 Audio Serial InterfaceThe audio serial interface for the PCM175x devices consists of a 3-wire synchronous serial port. The interfaceincludes LRCK (pin 3), BCK (pin 1), and DATA (pin 2). The BCK pin is the serial audio bit clock, and it is used toclock the serial data present on the DATA pin into the serial shift register of the audio interface. Serial data isclocked into the PCM175x on the rising edge of the BCK pin. The LRCK pin is the serial audio left and right wordclock. This pin is used to latch serial data into the internal registers of the serial audio interface.
Both the LRCK and BCK pins should be synchronous to the system clock. Ideally, TI recommendeds that theLRCK and BCK pins be derived from the system clock input, SCK. The LRCK pin is operated at the samplingfrequency, fS. The BCK pin can be operated at 32, 48, or 64 times the sampling frequency for standard (right-justified) format, and 32 times the sampling frequency of the BCK pin is limited to 16-bit right-justified format only.The BCK pin can be operated at 48 or 64 times the sampling frequency for the I2S and left-justified formats. 48times the sampling frequency of BCK is limited to 192/384/768 fS SCKI.
Internal operation of the PCM175x devices is synchronized with the LRCK pin. Accordingly, internal operation isheld when the sampling rate clock of the LRCK pin is changed or when the SCK pin and/or BCK pin isinterrupted for a 3-bit clock cycle or longer. If th SCK, BCK, and LRCK pins are provided continuously after thisheld condition, the internal operation is re-synchronized automatically in a period of less than 3/fS. Externalresetting is not required.
8.3.2.1 Audio Data Formats and TimingThe PCM1753 device supports industry-standard audio data formats, including right-justified, I2S, and left-justified. The PCM1754 device supports I2S and 16-bit-word right-justified audio data formats. Figure 23 showsthe data formats. Data formats are selected using the format bits, FMT[2:0], located in control register 20 of thePCM1753 device, and are selected using the FMT pin on the PCM1754 device. The default data format is 24-bitleft-justified. All formats require binary 2s-complement MSB-first audio data. The Audio Interface Timing tableshows a detailed timing diagram for the serial audio interface.
Figure 22. Audio Interface Timing
14 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
LRCK
(2) I2S Data Format; L-Channel = LOW, R-Channel = HIGH
MSB LSB
1/fS
(= 32 fS , 48 fS, or 64 fS)
18-Bit Right-Justified, BCK = 48 f S or 64 fS
1/fS
(1) Standard Data Format; L-Channel = HIGH, R-Channel = LOW
(3) Left-Justified Data Format; L-Channel = HIGH, R-Channel = LOW
MSB LSB
20-Bit Right-Justified, BCK = 48 f S or 64 fS
MSB LSB
24-Bit Right-Justified, BCK = 48 f S or 64 fS
1/fS
(= 48 fS or 64 fS)
(= 48 fS, or 64 fS)
MSB LSB
16-Bit Right-Justified, BCK = 32 f S
16-Bit Right-Justified, BCK = 48 f S or 64 fS
MSB LSB
L-Channel R-Channel
BCK
DATA 14 15 16 1 2 3 14 15 16
14 15 16 1 2 3 14 15 16
16 17 18
DATA
DATA
DATA
DATA
1 2 3 16 17 18
18 19 20 1 2 3 18 19 20
22 23 24 1 2 3
MSB LSB
MSB LSB
MSB LSB
MSB LSB
1 2 3 14 15 16
1 2 3 14 15 16
1 2 3 16 17 18
1 2 3 18 19 20
22 23 24
MSB LSB
1 2 3 22 23 24
L-Channel R-ChannelLRCK
BCK
DATA 1 2 3 12
MSB
N–2 NN–1
LSB
1 2 3
MSB
N–2 NN–1
LSB
L-Channel R-ChannelLRCK
BCK
DATA 1 2 3 N–2 NN–1 1 2 3 N–2 NN–1 1 2
MSB LSB LSBMSB
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
Figure 23. Audio Data Input Formats
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: PCM1753 PCM1754 PCM1755
–60
–50
–40
–30
–20
–10
0
10
Frequency (kHz)
Level (d
B)
0.1 100 1k 10k1 10
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
8.3.3 Zero Flag (PCM1754)The PCM1754 device has a ZERO flag pin, ZEROA (pin 11). ZEROA is the L-channel and R-channel commonzero flag pin. If the data for L-channel and R-channel remains at a 0 level for 1024 sampling periods (or LRCKclock periods), ZEROA is set to a logic 1 state.
8.3.4 Zero Flag (PCM1753)Zero-Detect Condition
Zero detection for either output channel is independent from the other channel. If the data for a given channelremains at a 0 level for 1024 sample periods (or LRCK clock periods), a zero-detect condition exists for thatchannel.
8.3.5 Zero Flag OutputsIf a zero-detect condition exists for one or more channels, the zero flag pins for those channels are set to a logic1 state. There are zero flag pins for each channel, ZEROL (pin 12) and ZEROR (pin 11). These pins can be usedto operate external mute circuits, or used as status indicators for a microcontroller, audio signal processor, orother digitally controlled function. The active polarity of zero flag outputs can be inverted by setting the ZREV bitof control register 22 to 1. The reset default is active-high output, or ZREV = 0. The L-channel and R-channelcommon zero flag can be selected by setting the AZRO bit of control register 22 to 1. The reset default isindependent zero flags for L-channel and R-channel, or AZRO = 0.
8.3.6 Analog OutputsThe PCM1753 device includes two independent output channels, VOUTL and VOUTR. These are unbalancedoutputs, each capable of driving 4 VPP typical into a 5-kΩ ac-coupled load. The internal output amplifiers forVOUTL and VOUTR are biased to the dc common-mode (or bipolar zero) voltage, equal to 0.5 VCC.
The output amplifiers include an RC continuous-time filter, which helps to reduce the out-of-band noise energypresent at the DAC outputs due to the noise shaping characteristics of the PCM1754 delta-sigma D/A converters.The frequency response of this filter is shown in Figure 24. By itself, this filter is not enough to attenuate the out-of-band noise to an acceptable level for many applications. An external low-pass filter is required to providesufficient out-of-band noise rejection. Further discussion of DAC post-filter circuits is provided in the ApplicationsInformation section of this data sheet.
Figure 24. Output Filter Frequency Response
16 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
–
–
VCOM
OPA337
+
10 Fµ+
PCM1754
Buffered VCOM
VCC
VOUTX(1) 10 µF
+
R
R2
1
VCOM
(1) X = L or R
1/2
OPA2353
+
Filtered
Output
VCC
2
3
1
C1
R3
R2
C2
R1
10 µF+
(a) Using VCOM to Bias a Single-Supply Filter Stage
(b) Using a Voltage Follower to Buffer VCOM When Biasing Multiple Nodes
PCM1754
A = –1, where A = –V V
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
8.3.6.1 VCOM OutputOne unbuffered common-mode voltage output pin, VCOM (pin 10) is brought out for decoupling purposes. This pinis nominally biased to a dc voltage level equal to 0.5 VCC. This pin can be used to bias external circuits.Figure 25 shows an example of using the VCOM pin for external biasing applications.
Figure 25. Biasing External Circuits Using the VCOM Pin
8.4 Device Functional Modes
8.4.1 Hardware Control (PCM1754)The digital functions of the PCM1754 are capable of hardware control. Table 3 lists selectable formats, Table 4shows de-emphasis control, and Table 5 lists mute control.
Table 3. Data Format SelectFMT (PIN 15) DATA FORMAT
LOW 16– to 24–bit, I2S formatHIGH 16–bit right–justified
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: PCM1753 PCM1754 PCM1755
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
Table 4. De-Emphasis ControlDEMP (PIN 13) DE–EMPHASIS FUNCTION
LOW 44.1 kHz de–emphasis OFFHIGH 44.1 kHz de–emphasis ON
Table 5. Mute ControlMUTE (PIN 14) MUTE
LOW Mute OFFHIGH Mute ON
8.4.2 Oversampling Rate Control (PCM1754)The PCM1754 automatically controls the oversampling rate of the delta-sigma DACs with the system clock rate.The oversampling rate is set to 64× oversampling with every system clock and sampling frequency.
8.5 Programming
8.5.1 Software Control (PCM1753/55)The PCM1753 and PCM1755 devices have many programmable functions which can be controlled in thesoftware control mode. The functions are controlled by programming the internal registers using the ML, MC, andMD pins.
The serial control interface is a 3-wire serial port, which operates asynchronously to the audio serial interface.The serial control interface is used to program the on-chip mode registers. The control interface includes MD (pin13), MC (pin 14), and ML (pin 15). The MD pin is the serial data input, used to program the mode registers. TheMC pin is the serial bit clock, used to shift data into the control port. The ML pin is the control port latch clock.
8.5.1.1 Register Write OperationAll write operations for the serial control port use 16-bit data words. lists the control data word format. The mostsignificant bit must be a 0. There are seven bits, labeled IDX[6:0], that set the register index (or address) for thewrite operation. The least significant eight bits, D[7:0], contain the data to be written to the register specified byIDX[6:0].
lists the functional timing diagram for writing to the serial control port. ML is held at a logic 1 state until a registerneeds to be written. To start the register write cycle, ML is set to logic 0. Sixteen clocks are then provided onMC, corresponding to the 16 bits of the control data word on MD. After the sixteenth clock cycle has completed,ML is set to logic 1 to latch the data into the indexed mode control register.
Control Data Word Format for MD
Register Write Operation
18 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
8.6 Register Maps
8.6.1 Mode Control Registers (PCM1753/55)
8.6.1.1 User-Programmable Mode ControlsThe PCM1753/55 devices include a number of user-programmable functions, which are accessed via controlregisters. The registers are programmed using the serial control interface, which was previously discussed in thisdata sheet. Table 6 lists the available mode control functions, along with their reset default conditions andassociated register index.
Table 6. User-Programmable Mode ControlsFUNCTION RESET DEFAULT REGISTER BIT(s)
Digital attenuation control, 0 dB to –63 dB in 0.5-dB steps 0 dB, no attenuation 16 and 17 AT1[7:0], AT2[7:0]Soft mute control Mute disabled 18 MUT[2:0]Oversampling rate control (64 fS or 128 fS) 64 fS oversampling 18 OVERSoft reset control Reset disabled 18 SRSTDAC operation control DAC1 and DAC2 enabled 19 DAC[2:1]De-emphasis function control De-emphasis disabled 19 DM12De-emphasis sample rate selection 44.1 kHz 19 DMF[1:0]Audio data format control 24-bit left-justified 20 FMT[2:0]Digital filter rolloff control Sharp rolloff 20 FLTZero flag function select L-, R-channel independent 22 AZROOutput phase select Normal phase 22 DREVZero flag polarity select High 22 ZREV
The mode control register map is shown in Table 7. Each register includes an index (or address) indicated by theIDX[6:0] bits.
Table 7. Mode Control Register Map (1)
IDX(B8–B REGISTER B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0
14)
10h Register 16 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 AT17 AT16 AT15 AT14 AT13 AT12 AT11 AT10
11h Register 17 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 AT27 AT26 AT25 AT24 AT23 AT22 AT21 AT20
12h Register 18 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 SRST OVER RSV RSV RSV RSV MUT2 MUT1
13h Register 19 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV DMF1 DMF0 DM12 RSV RSV DAC2 DAC1
14h Register 20 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV RSV FLT RSV RSV FMT2 FMT1 FMT0
16h Register 22 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV RSV RSV RSV RSV AZRO ZREV DREV
(1) RSV: Reserved for test operation. It should be set to 0 for regular operation.
8.6.1.2 Register Definitions
8.6.1.2.1 ATx[7:0]: Digital Attenuation Level Setting
Where x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) and VOUTR (x = 2).
Default value: 1111 1111b
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: PCM1753 PCM1754 PCM1755
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
Each DAC channel (VOUTL and VOUTR) includes a digital attenuation function. The attenuation level can be setfrom 0 dB to –63 dB in 0.5-dB steps. Changes in attenuator levels are made by incrementing or decrementingone step (0.5 dB) for every 8/fS time internal until the programmed attenuator setting is reached. Alternatively,the attenuation level can be set to infinite attenuation (or mute).
The attenuation data for each channel can be set individually. The attenuation level is set using the followingformula:
Attenuation level (dB) = 0.5 × (ATx[7:0]DEC – 255)where ATx[7:0]DEC = 0 through 255.
For ATx[7:0]DEC = 0 through 128, attenuation is set to infinite attenuation.
The table in Figure 26 shows the attenuation levels for various settings:
Figure 26. ATx[7:0]: Digital Attenuation Level Setting Table
8.6.1.2.2 MUTx: Soft Mute Control
where x = 1 or 2, corresponding to the DAC outputs VOUTL (x = 1) and VOUTR (x = 2).
Default value: 0
The mute bits, MUT1 and MUT2, are used to enable or disable the soft mute function for the corresponding DACoutputs, VOUTL and VOUTR. The soft mute function is incorporated into the digital attenuators. When mute isdisabled (MUTx = 0), the attenuator and DAC operate normally. When mute is enabled by setting MUTx = 1, thedigital attenuator for the corresponding output is decreased from the current setting to infinite attenuation, oneattenuator step (0.5 dB) for every 8/fS seconds. This provides pop-free muting of the DAC output.
By setting MUTx = 0, the attenuator is increased one step for every 8/fS seconds to the previously programmedattenuation level.
8.6.1.2.3 OVER: Oversampling Rate Control
Default value: 0
System clock rate = 256 fS, 384 fS, 512 fS, 768 fS, or 1152 fS:
System clock rate = 128 fS or 192 fS:
20 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
The OVER bit is used to control the oversampling rate of the delta-sigma D/A converters. The OVER = 1 settingis recommended when the sampling rate is 192 kHz (system clock rate is 128 fS or 192 fS).
8.6.1.2.4 SRST: Reset
Default value: 0
The SRST bit is used to enable or disable the soft reset function. The operation is the same as power-on reset.All registers are initialized.
8.6.1.2.5 DACx: DAC Operation Control
Where x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) or VOUTR (x = 2).
Default value: 0
The DAC operation controls are used to enable and disable the DAC outputs, VOUTL and VOUTR. When DACx =0, the corresponding output generates the audio waveform dictated by the data present on the DATA pin. WhenDACx = 1, the corresponding output is set to the bipolar zero level, or 0.5 VCC.
8.6.1.2.6 DM12: Digital De-Emphasis Function Control
Default value: 0
The DM12 bit is used to enable or disable the digital de-emphasis function. See the plots shown in the TypicalCharacteristics section of this data sheet.
8.6.1.2.7 DMF[1:0]: Sampling Frequency Selection for the De-Emphasis Function
Default value: 00
The DMF[1:0] bits are used to select the sampling frequency used for the digital de-emphasis function when it isenabled.
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: PCM1753 PCM1754 PCM1755
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
8.6.1.2.8 FMT[2:0]: Audio Interface Data Format
Default value: 101
The FMT[2:0] bits are used to select the data format for the serial audio interface. The table in Figure 27 showsthe available format options.
Figure 27. FMT[2:0]: Audio Interface Data Format Table
8.6.1.2.9 FLT: Digital Filter Rolloff Control
Default value: 0
The FLT bit allows the user to select the digital filter rolloff that is best suited to the application. Two filter rolloffselections are available, sharp and slow. The filter responses for these selections are shown in the TypicalCharacteristics section of this data sheet.
8.6.1.2.10 DREV: Output Phase Select
Default value: 0
The DREV bit is the output analog signal phase control.
8.6.1.2.11 ZREV: Zero Flag Polarity Select
Default value: 01h
The ZREV bit allows the user to select the polarity of zero flag pins.
8.6.1.2.12 AZRO: Zero Flag Function Select
Default value: 0
22 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
The AZRO bit allows the user to select the function of zero flag pins.
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 23
Product Folder Links: PCM1753 PCM1754 PCM1755
BCK 16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
DATA
LRCK
DGND
NC
VCC
VOUTL
VOUTR
SCK
AGND
FMT
MUTE
DEMP
TEST
VCOM
ZEROA
10 µF
Post LPF
10 µF
PCM1754
+5 V
+
L-Ch Out
PCM Audio Data
+
Post LPF
R-Ch Out
System Clock
Zero Mute Control
Format
MUTE On/Off
DEMP On/Off
++
10 µF
10 µF
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
9 Application and Implementation
NOTEInformation in the following applications sections is not part of the TI componentspecification, and TI does not warrant its accuracy or completeness. TI’s customers areresponsible for determining suitability of components for their purposes. Customers shouldvalidate and test their design implementation to confirm system functionality.
9.1 Application InformationThe delta-sigma section of the PCM175x device is based on an 8-level amplitude quantizer and a 4th-order noiseshaper. This section converts the oversampled input data to 8-level delta-sigma format. A block diagram of the 8-level delta-sigma modulator is shown in Figure 30. This 8-level delta-sigma modulator has the advantage ofstability and clock jitter sensitivity over the typical one-bit (2-level) delta-sigma modulator.
The combined oversampling rate of the delta-sigma modulator and the interpolation filter is 64 fS.
The theoretical quantization noise performance of the 8-level delta-sigma modulator is shown in Figure 33 andFigure 34. The enhanced multilevel delta-sigma architecture also has advantages for input clock jitter sensitivitydue to the multilevel quantizer, with the simulated jitter sensitivity shown in Figure 35.
The PCM175X devices are suitable for a wide variety of cost-sensitive consumer applications requiring goodperformance and operation with a single 5-V supply.
9.2 Typical ApplicationA basic connection diagram is shown in Figure 28, with the necessary power supply bypassing and decouplingcomponents. TI recommends using the component values shown in Figure 28 for all designs.
The use of series resistors (22 Ω to 100 Ω) is recommended for the SCK, LRCK, BCK, and DATA inputs. Theseries resistor combines with the stray PCB and device input capacitance to form a low-pass filter, which reduceshigh-frequency noise emissions and helps to dampen glitches and ringing present on clock and data lines.
For this design example, use the parameters listed in Table 8.
Figure 28. Basic Connection Diagram
24 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
–2
3
1OPA2134
+
VOUT
R4
C2
C1
R3
R2
R1
VIN
R
R
2
1
A = –V
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
Typical Application (continued)9.2.1 Design Requirements
9.2.1.1 Design ParametersTable 8 lists the design parameters and example values for the PCM175x devices.
Table 8. Design ParametersDESIGN PARAMETER EXAMPLE VALUE
Audio input PCM audio dataAnalog output 0 VPP - 4 VPP
Part configuration Hardware
9.2.1.2 Power Supplies and GroundingThe PCM1754 device requires 5 V for VCC.
Proper power supply bypassing is shown in Figure 28. The 10-μF capacitors should be tantalum or aluminumelectrolytic.
9.2.1.3 D/A Output Filter CircuitsDelta-sigma D/A converters use noise-shaping techniques to improve in-band signal-to-noise ratio (SNR)performance at the expense of generating increased out-of-band noise above the Nyquist frequency, or fS/2. Theout-of-band noise must be low-pass filtered in order to provide the optimal converter performance. This isaccomplished by a combination of on-chip and external low-pass filtering.
Figure 25(a) and Figure 29 show the recommended external low-pass active filter circuits for single- and dual-supply applications. These circuits are 2nd-order Butterworth filters using the multiple feedback (MFB) circuitarrangement, which reduces sensitivity to passive component variations over frequency and temperature. Formore information regarding MFB active filter design, see Burr-Brown applications bulletin (SBAA055), availablefrom the TI Web site at http://www.ti.com.
Because the overall system performance is defined by the quality of the D/A converters and their associatedanalog output circuitry, high-quality audio operational amplifiers are recommended for the active filters. TI'sOPA2353 and OPA2134 dual operational amplifiers are shown in Figure 25(a) and Figure 29, and arerecommended for use with the PCM1754 device.
Figure 29. Dual-Supply Filter Circuit
9.2.2 Detailed Design Procedure
9.2.2.1 Total Harmonic Distortion + NoiseTotal harmonic distortion + noise (THD+N) is a significant figure of merit for audio D/A converters because ittakes into account both harmonic distortion and all noise sources within a specified measurement bandwidth.The average value of the distortion and noise is referred to as THD+N.
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 25
Product Folder Links: PCM1753 PCM1754 PCM1755
++
Z–1
++ +
++
+
8-Level Quantizer
Z–1IN
8 fS
OUT
64 fS
++
Z–1
++
Z–1
+
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
For the PCM175x, THD+N is measured with a full-scale, 1-kHz digital sine wave as the test stimulus at the inputof the DAC (see Figure 31). The digital generator is set to 24-bit audio word length and a sampling frequency of44.1 kHz or 96 kHz. The digital generator output is taken from the unbalanced S/PDIF connector of themeasurement system. The S/PDIF data is transmitted via a coaxial cable to the digital audio receiver on theDEM-DAI1753 demonstration board. The receiver is then configured to output 24-bit data in either I2S or left-justified data format. The DAC audio interface format is programmed to match the receiver output format. Theanalog output is then taken from the DAC post filter and connected to the analog analyzer input of themeasurement system. The analog input is band limited using filters resident in the analyzer. The resultingTHD+N is measured by the analyzer and displayed by the measurement system.
Figure 30. Eight-Level Delta-Sigma Modulator
9.2.2.2 Dynamic RangeDynamic range is specified as A-weighted THD+N measured with a –60-dB full-scale, 1-kHz digital sine wavestimulus at the input of the D/A converter. This measurement is designed to give a good indicator of how theDAC performs given a low-level input signal.
The measurement setup for the dynamic range measurement is shown in Figure 32, and is similar to the THD+Ntest setup discussed previously. The differences include the band limit filter selection, the additional A-weightingfilter, and the –60-dB full-scale input level.
26 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
S/PDIF
Receiver
Evaluation Board
DEM-DAI1753
PCM1754
2nd-Order
Low-Pass
Filter
AES17 Filter
Band Limit
A-Weighting
Filter(1)
Analyzer
and
Display
Digital
GeneratorS/PDIF
Output
0% Full-Scale,
Dither Off (SNR)
or –60 dB FS,
1 kHz Sine Wave
(Dynamic Range)
Averaging
Mode
HPF = 400 Hz
LPF = 30 kHz
f–3 dB = 20.9 kHz
f–3 dB = 54 kHz or 108 kHz
(1) Results without A-Weighting are approximately 3 dB worse.
Audio Precision System Two
S/PDIF
Receiver
Evaluation Board
DEM-DAI1753
PCM1754
2nd-Order
Low-Pass
Filter
AES17 Filter
Band Limit
Analyzer
and
Display
Digital
GeneratorS/PDIF
Output0 dB FS
(100% Full-Scale),
24-Bit,
1-kHz Sine Wave
Averaging
Mode
HPF = 400 Hz
LPF = 30 kHz
f–3 dB = 20.9 kHz
f–3 dB = 54 kHz or 108 kHz
Audio Precision System Two
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
Figure 31. Test Setup for THD+N Measurement
9.2.2.3 Idle Channel Signal-to-Noise Ratio (SNR)The SNR test provides a measure of the noise floor of the D/A converter. The input to the D/A is all-0s data, andthe dither function of the digital generator must be disabled to ensure an all-0s data stream at the input of theD/A converter.
The measurement setup for SNR is identical to that used for dynamic range, with the exception of the inputsignal level.
(See the note provided in Figure 32).
Figure 32. Test Setup for Dynamic Range and SNR Measurement
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 27
Product Folder Links: PCM1753 PCM1754 PCM1755
Jitter (ps )p-p
90
95
100
105
110
115
120
125
0
Dynam
ic R
ange (
dB
)
100 200 300 400 500 600
Frequency [× f ]S
180
160
140
120
100
80
60
40
20
0
0 1 2 3 4 5 6 7 8
Am
plit
ude
(dB
)
Frequency [× f ]S
180
160
140
120
100
80
60
40
20
0
0 1 2 3 4 5 6 7 8
Am
plit
ude (
dB
)
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
9.2.3 Application Curves
Figure 33. Quantization Noise Spectrum (×64 Figure 34. Quantization Noise Spectrum (×128Oversampling) Oversampling)
Figure 35. Jitter Dependence (×64 Oversampling)
28 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
Digital Logic
and
Audio
Processor
Digital Power
+V DGNDD
Digital Section Analog Section
Return Path for Digital Signals
Analog Power
+VSAGND –VS+5VA
Digital
Ground
Analog
Ground
Output
Circuits
PCM1754
AGND
VCC
DGND
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
10 Power Supply RecommendationsThe PCM175x devices are designed to operate from a 4.5-V to 5.5-V power supply. Ensure that the powersupply is clean and use high-quality decoupling capacitors to reduce noise. The bulk capacitances can be fromeither tantalum or aluminum capacitors.
Separate power supplies are recommended for the digital and analog sections of the board. This prevents theswitching noise present on the digital supply from contaminating the analog power supply and degrading thedynamic performance of the PCM175x devices. In cases where a common 5-V supply must be used for theanalog and digital sections, an inductance (RF choke, ferrite bead) should be placed between the analog anddigital 5-V supply connections to avoid coupling of the digital switching noise into the analog circuitry. Figure 37shows the recommended approach for single-supply applications.
11 Layout
11.1 Layout GuidelinesFigure 36 shows a typical PCB floor plan for the PCM175x devices. A ground plane is recommended, with theanalog and digital sections being isolated from one another using a split or cut in the circuit board. The PCM175xshould be oriented with the digital I/O pins facing the ground plane split/cut to allow for short, direct connectionsto the digital audio interface and control signals originating from the digital section of the board.
Separate power supplies are recommended for the digital and analog sections of the board. This prevents theswitching noise present on the digital supply from contaminating the analog power supply and degrading thedynamic performance of the PCM175x. In cases where a common 5-V supply must be used for the analog anddigital sections, an inductance (RF choke, ferrite bead) should be placed between the analog and digital 5-Vsupply connections to avoid coupling of the digital switching noise into the analog circuitry. Figure 37 shows therecommended approach for single-supply applications.
11.2 Layout Example
Figure 36. Recommended PCB Layout
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 29
Product Folder Links: PCM1753 PCM1754 PCM1755
VDD
Digital Section Analog Section
RF Choke or Ferrite BeadPower Supplies
Common
Ground
Output
Circuits
AGND
VCC
+VS+5V –VSAGND
DGND
PCM1754
PCM1753, PCM1754, PCM1755SLES092D –APRIL 2010–REVISED AUGUST 2015 www.ti.com
Layout Example (continued)
Figure 37. Single-Supply PCB Layout
30 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: PCM1753 PCM1754 PCM1755
PCM1753, PCM1754, PCM1755www.ti.com SLES092D –APRIL 2010–REVISED AUGUST 2015
12 Device and Documentation Support
12.1 Related DocumentationFor related documentation see the following:• Dynamic Performance Testing of Digital Audio D/A Converters, SBAA055• OPA2353, High-Speed, Single-Supply, Rail-to-Rail Operational Amplifiers MicroAmplifier™ Series, SBOS103• OPA2134, SoundPlus™ High Performance Audio Operational Amplifiers, SBOS058• PLL1705, PLL1706 3.3-V Dual PLL Multiclock Generator, SLES046• PCM175x-Q1 24-Bit 192-kHz Sampling Enhanced Multi-Level Delta-Sigma Audio Digital-to-Analog Converter,
SLES254
12.2 Related LinksThe table below lists quick access links. Categories include technical documents, support and communityresources, tools and software, and quick access to sample or buy.
Table 9. Related LinksTECHNICAL SUPPORT &PRODUCT FOLDER SAMPLE & BUY TOOLS & SOFTWAREDOCUMENTS COMMUNITY
Click here Click here Click here Click here Click hereClick here Click here Click here Click here Click hereClick here Click here Click here Click here Click hereClick here Click here Click here Click here Click here
12.3 Community ResourcesThe following links connect to TI community resources. Linked contents are provided "AS IS" by the respectivecontributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms ofUse.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaborationamong engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and helpsolve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools andcontact information for technical support.
12.4 TrademarksE2E is a trademark of Texas Instruments.System Two, Audio Precision are trademarks of Audio Precision, Inc..All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge CautionThese devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foamduring storage or handling to prevent electrostatic damage to the MOS gates.
12.6 GlossarySLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable InformationThe following pages include mechanical, packaging, and orderable information. This information is the mostcurrent data available for the designated devices. This data is subject to change without notice and revision ofthis document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2010–2015, Texas Instruments Incorporated Submit Documentation Feedback 31
Product Folder Links: PCM1753 PCM1754 PCM1755
PACKAGE OPTION ADDENDUM
www.ti.com 24-Aug-2018
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status(1)
Package Type PackageDrawing
Pins PackageQty
Eco Plan(2)
Lead/Ball Finish(6)
MSL Peak Temp(3)
Op Temp (°C) Device Marking(4/5)
Samples
PCM1753DBQ ACTIVE SSOP DBQ 16 75 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -25 to 85 PCM1753
PCM1753DBQR ACTIVE SSOP DBQ 16 2000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -25 to 85 PCM1753
PCM1754DBQ ACTIVE SSOP DBQ 16 75 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -25 to 85 PCM1754
PCM1754DBQG4 ACTIVE SSOP DBQ 16 75 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -25 to 85 PCM1754
PCM1754DBQR ACTIVE SSOP DBQ 16 2000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -25 to 85 PCM1754
PCM1754DBQRG4 ACTIVE SSOP DBQ 16 2000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -25 to 85 PCM1754
PCM1755DBQ ACTIVE SSOP DBQ 16 75 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -25 to 85 PCM1755
PCM1755DBQR ACTIVE SSOP DBQ 16 2000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -25 to 85 PCM1755
(1) The marketing status values are defined as follows:ACTIVE: Product device recommended for new designs.LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.PREVIEW: Device has been announced but is not in production. Samples may or may not be available.OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substancedo not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI mayreference these types of products as "Pb-Free".RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide basedflame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
PACKAGE OPTION ADDENDUM
www.ti.com 24-Aug-2018
Addendum-Page 2
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuationof the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finishvalue exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on informationprovided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken andcontinues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF PCM1753, PCM1754 :
• Automotive: PCM1753-Q1, PCM1754-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device PackageType
PackageDrawing
Pins SPQ ReelDiameter
(mm)
ReelWidth
W1 (mm)
A0(mm)
B0(mm)
K0(mm)
P1(mm)
W(mm)
Pin1Quadrant
PCM1753DBQR SSOP DBQ 16 2000 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
PCM1754DBQR SSOP DBQ 16 2000 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
PCM1755DBQR SSOP DBQ 16 2000 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 5-Jun-2015
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
PCM1753DBQR SSOP DBQ 16 2000 367.0 367.0 35.0
PCM1754DBQR SSOP DBQ 16 2000 367.0 367.0 35.0
PCM1755DBQR SSOP DBQ 16 2000 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 5-Jun-2015
Pack Materials-Page 2
www.ti.com
PACKAGE OUTLINE
C
TYP-.244.228-6.195.80[ ]
.069 MAX[1.75]
14X .0250[0.635]
16X -.012.008-0.300.21[ ]
2X.175[4.45]
TYP-.010.005-0.250.13[ ]
0 - 8-.010.004-0.250.11[ ]
(.041 )[1.04]
.010[0.25]
GAGE PLANE
-.035.016-0.880.41[ ]
A
NOTE 3
-.197.189-5.004.81[ ]
B
NOTE 4
-.157.150-3.983.81[ ]
SSOP - 1.75 mm max heightDBQ0016ASHRINK SMALL-OUTLINE PACKAGE
4214846/A 03/2014
NOTES: 1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed .006 inch, per side. 4. This dimension does not include interlead flash.5. Reference JEDEC registration MO-137, variation AB.
116
.007 [0.17] C A B
98
PIN 1 ID AREA
SEATING PLANE
.004 [0.1] C
SEE DETAIL A
DETAIL ATYPICAL
SCALE 2.800
www.ti.com
EXAMPLE BOARD LAYOUT
.002 MAX[0.05]ALL AROUND
.002 MIN[0.05]ALL AROUND
(.213)[5.4]
14X (.0250 )[0.635]
16X (.063)[1.6]
16X (.016 )[0.41]
SSOP - 1.75 mm max heightDBQ0016ASHRINK SMALL-OUTLINE PACKAGE
4214846/A 03/2014
NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
METALSOLDER MASKOPENING
NON SOLDER MASKDEFINED
SOLDER MASK DETAILS
OPENINGSOLDER MASK METAL
SOLDER MASKDEFINED
LAND PATTERN EXAMPLESCALE:8X
SYMM
1
8 9
16
SEEDETAILS
www.ti.com
EXAMPLE STENCIL DESIGN
16X (.063)[1.6]
16X (.016 )[0.41]
14X (.0250 )[0.635]
(.213)[5.4]
SSOP - 1.75 mm max heightDBQ0016ASHRINK SMALL-OUTLINE PACKAGE
4214846/A 03/2014
NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design.
SOLDER PASTE EXAMPLEBASED ON .005 INCH [0.127 MM] THICK STENCIL
SCALE:8X
SYMM
SYMM
1
8 9
16
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to itssemiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyersshould obtain the latest relevant information before placing orders and should verify that such information is current and complete.TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integratedcircuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products andservices.Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and isaccompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduceddocumentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statementsdifferent from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for theassociated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designersremain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers havefull and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI productsused in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, withrespect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerousconsequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm andtake appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer willthoroughly test such applications and the functionality of such TI products as used in such applications.TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended toassist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in anyway, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resourcesolely for this purpose and subject to the terms of this Notice.TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TIproducts, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specificallydescribed in the published documentation for a particular TI Resource.Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications thatinclude the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISETO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTYRIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, orother intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationregarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty orendorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of thethird party, or a license from TI under the patents or other intellectual property of TI.TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES ORREPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TOACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OFMERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUALPROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OFPRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES INCONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEENADVISED OF THE POSSIBILITY OF SUCH DAMAGES.Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, suchproducts are intended to help enable customers to design and create their own applications that meet applicable functional safety standardsand requirements. Using products in an application does not by itself establish any safety features in the application. Designers mustensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products inlife-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., lifesupport, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, allmedical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applicationsand that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatoryrequirements in connection with such selection.Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2018, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments:
PCM1753DBQ PCM1753DBQR PCM1753DBQG4 PCM1753DBQRG4