party wall - acoustic datasheet: robust detail e … · knauf insulation ltd po box 10, stafford...
TRANSCRIPT
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External wallMasonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesApproved Document E ‘Tie Type A’
Cavity width75mm (min)
Block thickness100mm (min) each leafBlock density 1850 to 2300 kg/m3
InsulationEarthwool Masonry Party Wall Slab 75mm or 100mm
Wall finish13mm plaster or cement: sand render with plaster skim
Party Wall - Acoustic Datasheet: Masonry, dense block, min. 75mm cavity ROBUST DETAIL E-WM-1TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-1 may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
KINE2268DAT - V0315
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
75 1200 455 Euroclass A1 A+ Yes Yes 0
100 1200 455 Euroclass A1 A+ Yes Yes 0
(i) When used in conjunction with effective edge sealing
For full information on E-WM-1 visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-1
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External wallMasonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesApproved Document E ‘Tie Type A’
Cavity width75mm (min)
Block thickness100mm (min) each leafBlock density 1350 to 1600 kg/m3
InsulationEarthwool Masonry Party Wall Slab 75mm or 100mm
Wall finish13mm plaster or cement: sand render with plaster skim
Party Wall - Acoustic Datasheet: Masonry, lightweight aggregate block, min. 75mm cavity ROBUST DETAIL E-WM-2TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-2 may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-2 visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-2
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
75 1200 455 Euroclass A1 A+ Yes Yes 1
100 1200 455 Euroclass A1 A+ Yes Yes 1
(i) When used in conjunction with effective edge sealing
KINE2269DAT - V0315
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External wallMasonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesApproved Document E ‘Tie Type A’
Cavity width75mm (min)
Block thickness100mm (min) each leafBlock density 1850 to 2300 kg/m3
InsulationEarthwool Masonry Party Wall Slab 75mm or 100mm
Wall finishGypsum based board (nominal 8kg per m2) mounted on dabs on cement: sand renderor Knauf Gypsum Parge Coat
Party Wall - Acoustic Datasheet: Masonry, dense block, min. 75mm cavity ROBUST DETAIL E-WM-3TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-3 may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-3 visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-3
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
75 1200 455 Euroclass A1 A+ Yes Yes 1
100 1200 455 Euroclass A1 A+ Yes Yes 1
(i) When used in conjunction with effective edge sealing
KINE2270DAT - V0315
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External wallMasonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesApproved Document E ‘Tie Type A’
Cavity width75mm (min)
Block thickness100mm (min) each leafBlock density 1350 to 1600 kg/m3
InsulationEarthwool Masonry Party Wall Slab 75mm or 100mm
Wall finishGypsum based board (nominal 8kg per m2) mounted on dabs on cement: sand renderor Knauf Gypsum Parge Coat
Party Wall - Acoustic Datasheet: Masonry, lightweight aggregate block, min. 75mm cavity ROBUST DETAIL E-WM-4TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-4 may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-4 visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-4
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
75 1200 455 Euroclass A1 A+ Yes Yes 1
100 1200 455 Euroclass A1 A+ Yes Yes 1
(i) When used in conjunction with effective edge sealing
KINE2271DAT - V0315
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External wallMasonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesApproved Document E ‘Tie Type A’
Cavity width75mm (min)
Block thickness100mm (min) each leafBlock density 1528 kg/m3 (Only Besblock "Star Performer")
InsulationEarthwool Masonry Party Wall Slab 75mm or 100mm
Wall finishGypsum based board (nominal 8kg per m2) mounted on dabs on cement: sand renderor Knauf Gypsum Parge Coat
Party Wall - Acoustic Datasheet: Masonry, Besblock "Star Performer" dense aggregate, min. 75mm cavity
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-5 may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-5 visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-5
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
75 1200 455 Euroclass A1 A+ Yes Yes 1
100 1200 455 Euroclass A1 A+ Yes Yes 1
(i) When used in conjunction with effective edge sealing
ROBUST DETAIL E-WM-5TM
KINE2272DAT - V0315
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External WallMasonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesApproved Document E ‘Tie Type A’
Cavity width75mm (min)
Block thickness100mm (min) each leafBlock density 600 to 800 kg/m3
InsulationEarthwool Masonry Party Wall Slab 75mm or 100mm
Wall finishGypsum based board (nominal 8kg per m2) mounted on dabs on cement: sand renderor British Gypsum Soundcoat Plus
Party Wall - Acoustic Datasheet: Masonry, aircrete block, min. 75mm cavity ROBUST DETAIL E-WM-6TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-6™ may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-6TM visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-6
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
75 1200 455 Euroclass A1 A+ Yes Yes 1
100 1200 455 Euroclass A1 A+ Yes Yes 1
(i) When used in conjunction with effective edge sealing
KINE2273DAT - V0315
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External Wall Masonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesAncon Building Products Staifix HRT4 or Clan PWT4
Cavity width75mm (min)
Block thickness100mm (min) each leafBlock density 600 to 800 kg/m3
InsulationEarthwool Masonry Party Wall Slab 75mm or 100mm
Wall finishGypsum based board (nominal 8kg per m2) mounted on dabs on cement: sand renderor British Gypsum Soundcoat Plus
Party Wall - Acoustic Datasheet: Masonry, aircrete block (thin joint), min. 75mm cavity ROBUST DETAIL E-WM-10TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-10™ may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-10TM visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-10
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
75 1200 455 Euroclass A1 A+ Yes Yes 0
100 1200 455 Euroclass A1 A+ Yes Yes 0
(i) When used in conjunction with effective edge sealing
KINE2274DAT - V0315
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External wallMasonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesApproved Document E ‘Tie Type A’
Cavity width100mm (min)
Block thickness100mm (min) each leafBlock density 1350 to 1600 kg/m3
InsulationEarthwool Masonry Party Wall Slab 100mm
Wall finishGypsum based board (nominal 8kg per m2) mounted on dabs on cement: sand renderor Knauf Gypsum Parge Coat
Party Wall - Acoustic Datasheet: Masonry, lightweight aggregate or nominated hollow or cellular blocks, min. 100mm cavity
ROBUST DETAIL E-WM-11TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-11 may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-11TM visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-11
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
100 1200 455 Euroclass A1 A+ Yes Yes 3
(i) When used in conjunction with effective edge sealing
KINE2275DAT - V0315
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External wallMasonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesApproved Document E ‘Tie Type A’
Cavity width75mm (min)
Block thickness100mm (min) each leafBlock density 1050 kg/m3 (only Plasmor "Aglite Ultima")
InsulationEarthwool Masonry Party Wall Slab 75mm or 100mm
Wall finishGypsum based board (nominal 8kg per m2) mounted on dabs on cement: sand renderor Knauf Gypsum Parge Coat
Party Wall - Acoustic Datasheet: Masonry, Plasmor "Aglite Ultima", lightweight aggregate blocks, min 75mm cavity
ROBUST DETAIL E-WM-12TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-12™ may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-12TM visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-12
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
75 1200 455 Euroclass A1 A+ Yes Yes 0
100 1200 455 Euroclass A1 A+ Yes Yes 0
(i) When used in conjunction with effective edge sealing
KINE2276DAT - V0315
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External wallMasonry (both leaves) with 50mm (min) cavityfully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesNo wall ties are to be inserted. Structural adequacy should be assessed by a structural engineer
Cavity width75mm (min)
Block thickness100mm (min) each leafBlock density 600 to 800 kg/m3
InsulationEarthwool Masonry Party Wall Slab 75mm or 100mm
Wall finishGypsum based board (nominal 8kg per m2) mounted on dabs on cement: sand render or British Gypsum Soundcoat Plus
Party Wall - Acoustic Datasheet: Masonry, aircrete block (thin joint untied), min. 75mm cavity
ROBUST DETAIL E-WM-13TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-13™ may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-13TM visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-13
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
75 1200 455 Euroclass A1 A+ Yes Yes 3
100 1200 455 Euroclass A1 A+ Yes Yes 3
(i) When used in conjunction with effective edge sealing
KINE2277DAT - V0315
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External wallMasonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesApproved Document E ‘Tie Type A’
Cavity width100mm (min)
Block thickness100mm (min) each leafBlock density 1850 to 2300 kg/m3
InsulationEarthwool Masonry Party Wall Slab 100mm
Wall finishGypsum based board (nominal 9.8kg per m2) mounted on dabs on cement: sand renderor Knauf Gypsum Parge Coat
Party Wall - Acoustic Datasheet: Masonry, dense aggregate block min. 100mm cavity
ROBUST DETAIL E-WM-16TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-16 may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-16 visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-16
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
100 1200 455 Euroclass A1 A+ Yes Yes 3
(i) When used in conjunction with effective edge sealing
KINE2278DAT - V0315
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External wallMasonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesApproved Document E ‘Tie Type A’
Cavity width100mm (min)
Block thickness100mm (min) each leafBlock density 1850 to 2300 kg/m3
InsulationEarthwool Masonry Party Wall Slab 100mm
Wall finish13mm plaster or cement: sand render with plaster skim
Party Wall - Acoustic Datasheet: Masonry, dense aggregate block, min.100mm cavity
ROBUST DETAIL E-WM-18TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-18 may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-18 visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-18
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
100 1200 455 Euroclass A1 A+ Yes Yes 3
(i) When used in conjunction with effective edge sealing
KINE2279DAT - V0315
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External wallMasonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesAncon Building Products Stafix HRT4
Block thickness100mm (min) each leafBlock density 1350 to 1600 or 1850 to 2300 kg/m3
Cavity width100mm (min)
InsulationEarthwool Masonry Party Wall Slab 100mm
Wall finishGypsum based board (nominal 8kg per m2) mounted on dabs on cement: sand renderor Knauf Gypsum Parge Coat
Party Wall - Acoustic Datasheet: MONAFLOOR® BRIDGESTOP® System Masonry, dense or lightweight aggregate block or nominated hollow or cellular blocks, min.100mm cavity
ROBUST DETAIL E-WM-19TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-19 may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-19 visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-19
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
100 1200 455 Euroclass A1 A+ Yes Yes 4
(i) When used in conjunction with effective edge sealing
KINE2280DAT - V0315
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External wallMasonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesApproved Document E ‘Tie Type A’
Cavity width100mm (min)
Block thickness100mm (min) each leafBlock density 1350 to 1600 kg/m3
InsulationEarthwool Masonry Party Wall Slab 100mm
Wall finish13mm plaster or cement: sand render with plaster skim
Party Wall - Acoustic Datasheet: Masonry, lightweight aggregate block, min. 100mm cavity
ROBUST DETAIL E-WM-21TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-21™ may be insulated with mineral wool with a maximum density of 40kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-21TM visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-21
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
100 1200 455 Euroclass A1 A+ Yes Yes 3
(i) When used in conjunction with effective edge sealing
KINE2281DAT - V0315
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Utilises revolutionary ECOSE® Technology a bio-based, no-added formaldehyde binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool DriTherm
Cavity Slabs in external walls
External wallMasonry (both leaves) with 50mm (min) cavity,fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible mineral wool
Wall tiesApproved Document E ‘Tie Type A’
Cavity width100mm (min)
Block thickness100mm (min) each leafBlock density 1350 to 1600 kg/m3
or Plasmor "Aglite Ultima"
InsulationEarthwool Masonry Party Wall Slab 100mm
Wall finishGypsum based board (nominal 10 kg/m2) mounted on dabs
Party Wall - Acoustic Datasheet: Masonry, lightweight aggregate blocks or Plasmor "Aglite Ultima", min. 100mm cavity
ROBUST DETAIL E-WM-22TM
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-22™ may be insulated using Knauf Insulation Earthwool Masonry Party Wall Slab. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-22TM visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-22
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
100 1200 455 Euroclass A1 A+ Yes Yes 3
(i) When used in conjunction with effective edge sealing
KINE2282DAT - V0317
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall thermal bypass
• Contributes to a zero effective U-value(i) to be claimed in SAP calculations
• Will accommodate variations in cavity width as the product is formed in-situ
• Installed at high speed by approved installing technicians
• Proven by independent robust co-heating testing
• Provides one insulation technique on-site when used in conjunction with
Supafil in external walls
External wallPorotherm inner leaf and masonry outer leaf, fully filled with DriTherm
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesOnly use Ancon Building Products CCBA 'Type A'
Cavity width100mm (min)
Block thickness100mm (min) each leaf
InsulationEarthwool Party Wall Slab
Wall finishGypsum based board (nominal 8kg per m2) mounted on dabson Porotherm Ecoparge coat (nominal 4mm, minimum 3mm)
Party Wall - Acoustic Datasheet: Masonry, Porotherm blocks-thin joint, min. 100mm cavity
ROBUST DETAIL E-WM-25TM
The Part E Robust Details Handbook states that the separating cavity in E-WM-25 may be insulated with mineral wool or batts with a maximum density of 20kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-25 visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-25
KINE2252DAT - V0315
Knauf Insulation Earthwool Masonry Party Wall Slab
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
100 1200 455 Euroclass A1 A+ Yes Yes 1
(i) When used in conjunction with effective edge sealing
Knauf Insulation LtdPO Box 10, Stafford Road, St Helens, Merseyside WA10 3NS
For further information contact our Technical Support TeamTel: 01744 766 666 Fax: 01744 612 007 E-mail: [email protected]
Benefits• Provides a solution to restrict heat loss through party wall bypass
• Contributes to a zero effective U-value to be claimed in SAP calculations(i)
• Easy to install and can be used as a template to control width of party wall cavity
• Utilises revolutionary ECOSE® Technology a bio-based formaldehyde free binder
technology, based on rapidly renewable materials instead of petro based chemicals
• Offers one insulation technique on-site when used in conjunction with Earthwool
DriTherm Cavity Slabs in external walls
External wallMasonry (both leaves) fully filled with Earthwool DriTherm Cavity Slab
Flexible Edge Seal Cavity StopEncapsulated non-combustible glass mineral wool
Wall tiesApproved Document E ‘Tie Type A’
Cavity width100mm (min)
Block thickness100mm (min) each leafBlock density 1528 kg/m3 (Only Besblock "Star Performer")
InsulationEarthwool Masonry Party Wall Slab 100mm
Wall finishGypsum based board 10kg/m2 mounted on dabs.
Party Wall - Acoustic Datasheet: Masonry, Besblock "Star Performer" dense aggregate, min. 100mm cavity
Knauf Insulation Earthwool Masonry Party Wall Slab
The Part E Robust Details Handbook states that the separating cavity in E-WM-26 may be insulated with 100mm mineral wool roll, quilt or batt with a density of 12-25kg/m3. - Knauf Insulation Earthwool Masonry Party Wall Slab meets this requirement. Acoustic testing has been completed to demonstrate suitability in the above construction. If this solution were used on site with an equivalent construction and the same build quality, it would achieve the sound insulation performance level required by Approved Document E.
For full information on E-WM-26 visit Robust Details website http://www.robustdetails.com/TheHandbook/RobustDetail/E-WM-26
Thickness(mm)
Length(mm)
Width(mm)
Fire Performance
Generic BRE Green Guide Rating
Contributes to zero effective U-value (i)
Acoustic performance in excess of
45dB DnT,w + Ctr
Code for Sustainable Homes credits
100 1200 455 Euroclass A1 A+ Yes Yes 1
(i) When used in conjunction with effective edge sealing
ROBUST DETAIL E-WM-26TM
KINE2253DAT - V0315