Duroboat Parts and Accessories

A

B

C

D

E

A. Stern Handles Current handles will fit most early Duroboats but may require some additional drilling on your gunwales and possibly a little encouragement from a rubber mallet. Please indicate port or starboard with order.$43ech., $9shipping, buy both and pay only one shipping charge.

B. Stern and Keel casting assembliesEach consist of a casting, a large washer, and a bolt. Price is per assembly. When ordering be sure to specify Port, Starboard, or Keel assembly. $26each, $10shipping, second and third assembly ships for free.

C. Bow Eye AssemblyThis is the 3 part assembly used on current Duroboats. It consists of three pieces, an inner and outer casting, and a stainless steel bow eye. It will replace the bow eye casting from early generation Duroboats. Installation requires use of Duroboat or other marine sealant sold separately.$42, $8shipping

D. Bow HandleBow Handle Casting shipped with Fasteners.$29, $7shipping

E. Oar Lock SocketsThese are designed to fit along side the Duroboat gunwale. They may work on other boats. The sockets will accept a ½ inch diameter oar lock.$26, $7shipping

F G 1/7

A. Neoprene Backed Washers These washers are used to seal the screw holes where the seats are bolted to the hull. Sold in packages of 10. They are stainless washers with a rubber like seal. Often replaced if the boat is being painted or they become unsightly from salt build up. $6.50, $5shipping

B. Touch up paint --yellow, teal, red, blueAs paint lots vary and paint on boats wear; these will be a close but possibly not perfect match. Good for small areas. If you need to paint a large area see the article on the subject at the Duroboat Experience$6, $3shipping

C. Drain Plug Don’t leave the launch ramp without it.$6, $4shipping

D. FastenersStainless pan head screws with nylock nuts. Package of 10.These are used to hold seats to hull and often replaced if a boat is being painted. $6.50, $6shipping

E. Sealant/Adhesive Urethane sealant has several uses in and around a Duroboat. Used in joints and behind rear corner castings. We often refer to it as Vulkem but it is currently a Trempro product. This sealant takes a few days to set well, so in some cases you may want to use a faster setting marine sealant available at marine stores. $13, $3shipping

F. E-6000 adhesiveUsed to adhere vinyl rubrail to gunwale. $14, $3shipping

G. RubrailRuns the full length of the gunwale to give the boat extra protection and a a clean look. Requires E-6000 adhesive or equivalent. $39 per 16’, $10shipping per 16’

A

B

C

D

E

F

G

2/7

Transom BoardsBoards are stained and come in small, medium and large sizes. Smalls are used on the 10’, 12’, and 14’ boats. Mediums are used on 14’ boats when a larger motor pad is desired. Mediums are standard on 14’ boats for 2007. Large boards are used on the 15’ and pre 2003 16’ boats. Boards are shipped with a set of stainless carriage bolts and nuts. Sun and salt are tough on wood so keep yours looking good with periodic light sanding and fresh varnish.Sm. $49, Md. $59, Lg. $79; $10-$15 for shippingSmall:

11.5’’x13’’

Large: 13.5’’x32.5’’

Medium: 12’’x16’’

3/7

A. Bowrail -- 8’ long and 9’’ highHigh Quality Stainless bowrail. Provides additional protection that adds a nautical look to Duroboats from 14 to 16ft. Difficult to ship, not always available.$460, call about shipping

B. Console Grab RailThese rails provide a place to grab in rough water or when getting in and out of the boat. May be installed on floor mount, bench mount or mini consoles at both helm or passenger positions. You must specify if they are floor or bench consoles. Grab rails ship with stainless fasteners. *Install to allow fingers to easily reach through between the top of the windscreen and the rail. $210, $20shipping

C. Split Side Rails High quality and strong stainless rails provide 6’ long 7’’ high added protection and good looks. These rails were designed for the 12’ and 14’ boats; but are often used on all of the other models. They allow boaters easier access to the boat from the beach. $349, $29shipping

D. Grabrails --Stainless 18’’These rails provide attractive handholds and tie off points for fenders.$35each, $14shipping

A

B

C

D

4/7

A. Downrigger Mounts Simple aluminum platforms that provide a flat surface for mounting your downrigger. Shipped with stainless fasteners and neoprene backed washers. $20, $8shipping

B. Trolling Motor MountThe Trolling motor mount is an aluminum platform that installs on the forward bow shelf of a Duroboat. The mount provides a flat 6”x19” platform that is 4” above the bow shelf. It should work with most trolling motors but we advise knowing the mounting requirements and deployment operation of your trolling motor before deciding if our mount will work for you. Consider how the combination will work.$34, $10shipping

C. Beach WheelsMake it easy to move your boat from the water to the beach. Wheels will fit boats 10’ to 15’, but are most practical for boats under 15’. Wheels stow up when on the water and fold down for use on the beach. Additional transom supports are required. Wheels are available in a set of two for $89.$279, $26shipping

D. Decals yellow, white, black$6each, $2shipping

A

B

C

D

5/7

A. Bench Mount Console BCON The BCON is essentially the same as the FCON but designed to mount to a Duroboat Bench instead of the floor. Works well on 16’,15’, and 14’ bench models.$710, $27shipping

B. MiniBCON MBCON has All the same features of the full size consoles. But with just a little less length in the body. Designed for and works best on 10 through 12 ft Duroboat Bench models. Can work on the 14 for folks who think they would be squeezed a little by the full size console. $649, $24shipping

C. Floor Mount Console FCONThe FCON provides a forward looking helm position. Highly recommended with boats greater than 30HP. The FCON includes a console body, steering wheel, steering gear, steering cable, detachable custom windscreen and a motor control mounting box. Motor controls, shift, and speed cables are supplied by your dealer to match your motor. Fits best on the 16’ and 15’ walk through boats, but will work on the 14’ as well.$710, $27shipping

D. Passenger Consoles FPAX or BPAXThe Floor or Bench passenger consoles are the same units as the full consoles. The steering gear is removed and the steering wheel hole covered. The floor version adds some extra storage. $424, $24shipping

A

B

C

D 6/7

To order parts or accessories please call us at the factory. Currently we do not take credit cards. Payment will need to be made via snail mail.

Phone: 731-986-2524

8405 Tennessee Hwy 22 Huntingdon, TN 38344

7/7