Fanatec® is a registered trademark of Endor AG

Designed and developed by Endor AG in Germany

Made in China

Quick Guide

EN

www.fanatec.com

ANALOGUE PADDLE MODES

PACKAGE CONTENTS

DATAPORT-C

To switch the Mode of your Podium Advanced Paddle Module you need to enter the Tuning Menu. This can be accessed using the FanaLab software, driver or a button/display module (sold separately).

For further information about the APM Modes, please read the Quick Guide or Manual for the Podium Advanced Paddle Module.

The DataPort-C on the bottom of the Podium Hub is to connect compatible FANATEC® peripherals with your wheel base.

ATTENTION: It is NOT a USB data port and cannot transfer any databetween a PC and any attached device that is not from Fanatec®.

ATTENTION: Download driver V336 or higher.

● Podium Hub

● Quick Release Adapter

● 2 mm Allen key

● Safety bolt

A

A

CC

B

B

NECESSARY FUNCTIONS

WHEEL COMPATIBILITY

Use M5 bolts with a maximum internal reach of 16 mm in order to avoid internal damage of the Podium Hub. Fanatec Wheel Rims come with the correct bolts. If your wheel rim is not pre-drilled, you can use the drilling template for the Podium Hub.

Ø 70 mm

Ø 50 mm

● To accept the High Torque warning message on a Podium Wheel Base, you need to turn the steering wheel 90° and wait until the bar on the wheel base display disappears.

● Centre Calibrate by clicking on “Centre Calibration” in the driver.

● Shifter Calibrate by clicking on “Shifter Calibration” in the driver.

● To adjust the wheel base Tuning Menu, you need to use the FanaLab software, driver or use a suitable button/display module (sold separately).

● Mode switching on wheel bases without a dedicated “Mode” button is only possible through the use of a suitable button/display module.

NOTE: The FunkySwitchTM is not compatible with the Podium Hub.

ATTENTION: Download driver V346 or higher.

ATTACHING THE PODIUM HUB

ATTENTION: Ensure that your Fanatec wheel base and Podium Hub firmwareisupdatedfromthedownloads section of www.fanatec.com.

● Remove the storage pin.

● Align wheel base axle to correct position.

● Slide the Podium Hub onto the wheel base axle up to the mechanical limit.

● Release the Quick Release mechanism.

● Compress and hold the Quick Release mechanism.

Page 1 Page 2 Page 3

DD

NOTE: Keep the storage pin for future use.

DETACHING THE PODIUM HUB

● Compress and hold the Quick Release mechanism.

● Pull off the Podium Hub from the wheel base axle.

● Compress and hold the Quick Release mechanism.

● Insert the storage pin (recommended for long-term storage).

● Release the Quick Release mechanism.

MOUNTING SHIFTER PADDLES

● Loosen the three highlighted bolts on the plastic cover. Use the included 2 mm Allen key.

● Remove the front cover.

● Connect the P APM cables to the correct sockets.

● Attach the front cover again, insert and tighten the three bolts. Position the cables carefully to avoid damage.

● Attach Podium Advanced Paddle Module (P APM; sold separately) using the M5x16 bolts from the package content and tighten them.

MOUNTING THE BUTTON CLUSTER PACK

● Loosen the three highlighted bolts on the plastic cover. Use the included 2 mm Allen key.

● Remove the front cover.

● Connect the Button Cluster cables to the correct sockets.

● Attach the front cover again, insert and tighten the three bolts. Position the cables carefully to avoid damage.

● Place the wheel rim on top of the washers, keeping it in place using all bolts except the two for the Button Clusters (one bolt for three-hole pattern, four bolts for six-hole pattern).

● Slide the Button Clusters in place, insert the remaining bolts and fasten slightlyinordertomakefinalpositioning adjustments,thentightenfirmly.

● Place the washers from the ClubSport Button Cluster Pack (BCP, sold separately) on the holes where no Button Clusters will be mounted.

MAPPING FOR BUTTON CLUSTER PACK

VIDEO

# Button no. PC Function PS4TM

1 00 SQUARE

2 01 CROSS

3 02 CIRCLE

4 03 TRIANGLE

5 08 SHARE

6 09OPTIONS

(PRESS & HOLD FOR 3 SECONDS FOR PS4TM SIGN-IN)

5 31 4

2 6

Watch our video named "The Podium Hub - Sim Racing Wheel Adapter | FANATEC" on the officialFanatecYouTubeTM channel for further visual reference.

ATTENTION: A suitable button/display module such as the Podium Button Module Endurance or ClubSport Button Cluster Pack is mandatory for use on PS4. These products add a 'PS-button' to the Podium Hub, which must be pressed to initiate/sign-in the connected Fanatec hardware on a PS4 console. Ensure that the "PS4 Mode" is selected on the wheel base by pressing TRIANGLE & SHARE simultaneously.

Page 4 Page 5 Page 6 Page 7