OWNER’SMANUAL702 and 715TPLINKSTER®

.22 CAL SEMI-AUTOMATIC RIFLEWITH DETACHABLE MAGAZINE

IMPORTANT “SAFETY WARNINGS” — NOTE THE SYMBOL

THESE SAFETY WARNINGS ARE FOR YOUR PROTECTION AS WELL ASTHE SAFETY OF OTHERS. DISREGARDING INFORMATION IN THIS MANU-AL MAY RESULT IN SERIOUS INJURY OR DEATH.

Be certain this owner’s manual is available for reference and is kept with this firearm if transferred to another party. If this manual is lost ormisplaced, contact the Product Service Center for a free replacementcopy or visit www.mossberg.com.

After performing any work on your firearm such as cleaning, adjustments,disassembly or installation of any accessory, the firearm should be re-checked for proper functioning before firing live ammunition.

Firearms are complex mechanisms. Any modification, alteration, orimproper fitting of parts may result in a dangerous malfunction, damageto the firearm and could cause serious injury or death to you or thosearound you. The firearm’s owner must accept full responsibility for thecorrect reassembly and functioning of the firearm after any disassemblyor replacement of parts.

If you do not understand any of the material in this manual or have anyquestions, contact the Product Service Center or a qualified gunsmith.

Do not attempt to load, handle or use the firearm until you read and under-stand the information contained in its owner’s manual. Before handling yourfirearm, you should learn how it operates and how to maintain it. This includesknowing its basic parts, how the manual safety and other safety featuresoperate, how to safely open and close the action and how to safely load andunload ammunition from the firearm. Improper use and handling is danger-ous and could cause serious injury or death to you or those around you. Allusers of the firearm must become thoroughly familiar with the instructions inthis manual.

TM

distributed by

MOSSBERG INTERNATIONAL, INC.P.O. BOX 497 • 7 GRASSO AVENUE, NORTH HAVEN, CT 06473

PHONE (800) 363-3555www.mossberg.com

Safety and safe firearms handling is everyone’s responsibility.

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 1

As the owner of a firearm, you must undertake the full-time responsibilityof safe firearms handling for your own safety and the safety of thosearound you:

• Keep all firearms and ammunition out of the reach of children.• Store your firearms and ammunition separately.• Never store a loaded firearm.• Never leave a loaded firearm unattended.• Never transport a loaded firearm in a vehicle.• Unload your firearm when you have stopped shooting and whenyou have to climb a tree, fence, cross a slippery surface or haveto transport it in a vehicle.

• Do not load your firearm before you are in a place where it issafe to shoot, and keep your finger off the trigger until you areon target and have decided to fire.

• Never shoot at water, rocks or any hard surfaces. Bullets mayglance off such surfaces and cause injuries.

• Do not use alcohol or drugs before or while handling firearms.• Do not touch the trigger while the safety button is being engagedor disengaged.

Always point the muzzle of your firearm in a safe direction, regardless of whether the firearm is loaded or unloaded. You should become thoroughly familiar with the function and operation of this firearm and theinstructions supplied with it.Always treat every firearm as it is were loaded. Give your firearm tosomeone with the action open (bolt fully rearward), and the safety buttonpushed fully to the right to the “ON” (SAFE) position, after you verify thefirearm is unloaded. Insist on the same procedure when receiving afirearm from someone else. Learn the location of all the safety featuresof your firearm and how they operate.Wear eye and ear protection when shooting. Shooting without proper earprotection can cause hearing damage. The use of eye protection duringany type of shooting is important to protect your vision.When using a firearm with mounted optics, maintain an adequate distance between the rear of the scope and your face at all times. Be certain the scope installation does not interfere with access to, or theproper functioning of the safety button.We specifically disclaim any responsibility for damage or injurywhatsoever occurring in connection with, or as a result of, the use offaulty, or non-SAAMI standard, or “remanufactured” or hand-loaded(reloaded) ammunition. Additionally, we disclaim any responsibilityfor damage or injury which results from any modifications orchanges that are not a part of the firearm as delivered from the fac-tory.Learn to clean your firearm thoroughly and make certain no oil, greaseor other materials are blocking the barrel. Obstructions of any kind cancause damage to the firearm resulting in personal injury.

Practice proper firearm maintenance and safety. Make sure all exposed metal surfaces are coated with a thin film of oil, especially after being exposed to dampweather. (See proper section of this manual for cleaning instructions.) Do not plugthe barrel or store in a fabric-lined case, which will absorb lubricants from thefirearm. Before using after storage, follow complete instructions stated in thismanual for refamiliarization with the firearm. A thorough inspection and function test should be performed before going into the field. Have your firearm periodically checked by a qualified gunsmith.

2PART NO. 17928 REV. F

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 2

TABLE OF CONTENTS

Page

General Information and Mechanical Characteristics . . . . 4, 5Mechanical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Magazine Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8Keeping the Bolt in the “OPEN” Position . . . . . . . . . . . . . . . . . 9Loading and Unloading the Magazine and Firearm . . . . . 10, 11Firing the Firearm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13Disassembly for Cleaning and Lubrication . . . . . . . . . . . . 13-16Cleaning and Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17To Re-assemble the Firearm . . . . . . . . . . . . . . . . . . . . . . . 18, 19Function Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 20Precautions and Care with your Firearm . . . . . . . . . . . . . . . . 20Sight Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 21Service Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Exploded View for Models without AR Style Stock . . . . . . . . 24Parts List for Models without AR Style Stock . . . . . . . . . . . . . 24Exploded View for Models with AR Style Stock . . . . . . . . . . . 25Parts List Models with AR Style Stock . . . . . . . . . . . . . . . . . . 25Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27Basic Rules of Safe Firearms Handling . . . . . . . . . Back Cover

3

A note about the warnings and information contained in this manual:

We strongly suggest that you check with your local licensed retailer or state policefor additional information concerning firearms ownership, or hunting or target shoot-ing rules that may be required by local law or regulation. Since such rules and regula-tions are subject to change, local authorities are in the best position to advise youon such matters.

WARNING: This product can expose you to chemicals,including lead, which are known to the State of California tocause cancer and birth defects or other reproductive harm.For more information go to www.P65Warnings.ca.gov.

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 3

GENERAL INFORMATION AND MECHANICAL CHARACTERISTICS

The 702 Plinkster® (including 715T models) is designed to operate with .22 longrifle cartridges of sub-sonic, standard, high or hyper velocities only.

When the firearm leaves the factory, its metal parts are protected by a coat of veryadherent oil. This coating, especially inside of the barrel, must be removed beforeusing the firearm. The oil on the outside surfaces should also be removed whenthe packing box has been open because the oil is very sticky and it easily retainsdust and other solid impurities from the air.

The firearm is designed to fire semi-automatically. Finger pressure must berelieved from the trigger before an additional shot can be fired.

WARNING

Because this firearm can be used as a single shot, it will fire whetheror not a magazine is in the firearm if a cartridge is chambered.

FIREARM WILL FIRE WITH MAGAZINE OUT.

4

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 4

5

Fig. 1

Butt Plate

Stock

Rear Sight

Receiver Operating Handle

Bolt

Muzzle

Clip Magazine

Magazine LockSafetyButton

* The chamber is the rearmost part of the barrel. It can only be seen when thebolt is in the “open” position.

TriggerGuard

Trigger

Chamber*Barrel

Front Sight

Fig. 2

Clip Magazine

Magazine Release(Both Sides)

SafetyButton

TriggerGuard

Trigger

Stock

Receiver Shell(Both Sides)

Bolt

Operating Handle

Chamber*Rear Sight Barrel

Front Sight

Muzzle

* The chamber is the rearmost part of the barrel. It can only be seen when thebolt is in the “open” position.** The receiver is enclosed in the receiver shells.

Receiver**

Forearm(Both Sides)

StockBolt

Sling Swivel

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 5

6

Read and understand this entire manual and its safety warnings beforefiring the firearm.

MECHANICAL SAFETY

The safety button is located at the front of the trigger guard (Fig. 3) and must bemanually moved to the desired position by the shooter. The safety mechanismcannot be engaged unless the hammer is cocked.

The safety is set in the “ON” (SAFE) position by pushing the button fromthe left side (side opposite the ejection port) so that it moves all the wayto the right. The button must always be pushed fully to the right until itmoves no further to be in the “ON” (SAFE) position.

Remember, a firearm’s manual safety is a mechanical device which cannever replace safe firearm handling practices.

Because any mechanical device can fail, never rely on any mechanismor safety device to prevent the dangers of careless handling or pointinga firearm in an unsafe direction.

Moving the safety button fully to the left will put the safety in the “OFF” (FIRE)position. The safety should be in the “ON” (SAFE) position until you are on targetand have decided to fire.

The safety button is designed to function only as described above andshould not be reversed. Do not attempt to remove or reverse the button.Doing so will result in an unsafe condition which can cause serious injuryor death.

The safety button is marked with a red ring as a training aid used only to showthe direction of the “ON” (SAFE) position and should not be used as an indicatorthat the safety is “ON” or “OFF.”

Fig. 3

SafetyButton

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 6

MAGAZINE INSTALLATION

Familiarize yourself with the firearm by installing and removing an unloaded clipmagazine and by learning to keep the bolt in the open position.

Ensure the safety button is fully to the right to the “ON” (SAFE) positionand visually and physically check the chamber and the receiver area tobe certain the firearm is unloaded.

7

Fig. 4

Fig. 5

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 7

8

WARNING

Removal of the magazine will not unload the firearm! Removing themagazine will not remove any cartridge which is in the firearm’s cham-ber! A cartridge in the firearm’s chamber can still be fired, even afterthe firearm’s magazine has been removed! After you remove the mag-azine always visually and physically inspect the chamber and receiverto ensure the firearm is completely unloaded!

FIREARM WILL FIRE WITH MAGAZINE OUT.

TO INSTALL CLIP MAGAZINEInsert the unloaded clip magazine with the red cartridge follower end first and thelong flat portion of the clip to the rear of the magazine opening. Push the maga-zine into place until it snaps into its locked position. (Fig. 4 & 5) On models withAR style stock, be sure that the release lever is returned to its upmost position sothat the magazine will snap into its locked position.

TO REMOVE CLIP MAGAZINE FROM MODELS WITHOUT AR STYLE STOCKPress the magazine lock forward toward muzzle and pull the magazine from thestock with your free hand. (Fig. 4)

TO REMOVE CLIP MAGAZINE FROM MODELS WITH AR STYLE STOCKPress down on the magazine release on either side of the receiver shell and pullthe magazine from the stock with your free hand. (Fig. 5)

NOTE: It is easier to install and remove the magazine from the firearm if the bolt islocked at its most rearward position by its operating handle. (Fig. 6 & 7)

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 8

9

Fig. 6

Fig. 7

KEEPING THE BOLT IN THE “OPEN” POSITION

If the magazine is not installed, pull the operating handle fully rearward then pushthe handle inward. To release the bolt, pull the end of the operating handle to therear and outward to release.

If an empty magazine is installed, the magazine follower will keep the bolt in anopen position. (Fig. 6) To remove the magazine, follow the instructions for yourparticular model in “To Remove Clip Magazine” section of this manual.

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 9

TO LOAD AND UNLOAD MAGAZINE AND FIREARM

The magazine should be loaded before installing it to the firearm. Remove it fromfirearm as described in “To Remove Clip Magazine” section of this manual.

Load the magazine by inserting one cartridge at a time, pressing against the plasticfollower and rearwards until it is fixed between the lips of the magazine. Repeatthe operation until the magazine is full, or until the desired number of cartridgeshave been loaded. The magazine should be loaded with .22 Long Firearm car-tridges only (Fig. 9). For best performance we recommend using Hi-Velocityammunition.

10

Fig. 8

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 10

Before inserting the magazine into the firearm, point the muzzle in a safedirection, pull the operating handle fully rearward, release it, and let thebolt return to its most forward position. Move the safety button fully to theright to the “ON” (SAFE) position.

Insert the loaded magazine into the magazine opening until it snaps intoits locked position.

Point the muzzle in a safe direction and ensure the safety button is still positioned fully to the right at the “ON” (SAFE) position. Using the operating handle, pull the bolt to its most rearward position, release it,and let the bolt return freely to its forward position. It may be necessaryto pull out on the operating handle when it is in its most rearward positionto get it to return to its forward position. The bolt will push one cartridgefrom the magazine into the chamber.The firearm is now loaded.

Do not touch the trigger until you are on target and have decided to fire.

Removing the magazine does not unload the firearm! The firearm willfire if a cartridge is chambered, whether or not a magazine is in thefirearm.

Fig. 9

11

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 11

FIRINGUse of this product, including discharging firearms in poorly ventilatedares, cleaning firearms, or handling ammunition can result in exposureto chemicals, including lead, which are known to the state of Californiato cause serious physical injury, including cancer, birth defects or otherreproductive harm. For more information, go towww.P65Warnings.ca.gov.Have adequate ventilation at all times and wash hands throughly afterexposure.

With the muzzle pointed in a safe direction and held in the proper firing position,move the safety button fully to the left to its “OFF” (FIRE) position. Pulling the trig-ger through its full travel to the rear, will fire the firearm. Ensure that the muzzleis pointed in a safe direction before placing your finger on the trigger.

Should any cartridge fail to fire, keep the muzzle pointed in a safe direc-tion for at least thirty (30) seconds in case the cartridge is a “hangfire”(delayed firing of the cartridge after being struck by the firing pin.) Then,remove the magazine (as it may still have loaded cartridges), pull theoperating handle fully rearward and lock the bolt in the open position(Fig. 6 & 7) and extract and eject the misfired cartridge. Move the safetybutton fully to the right to the “ON” (SAFE) position. Segregate the mis-fired cartridge from other ammunition. Do not attempt to refire a misfiredcartridge.If at any time during firing, the sound of any cartridge is noticeably louderor softer than previous cartridges fired, STOP! Do not load or fire addi-tional cartridges. Keep the muzzle pointed in a safe direction, removethe magazine (as it may still have loaded cartridges in it), and whilekeeping the ejection port and magazine well opening of the firearmturned away from your face (to protect your eyes in the event a defectivecartridge explodes), pull the operating handle fully rearward and lock theaction open. Visually and physically verify that the chamber is empty.Move the safety button fully to the right to the “ON” (SAFE) position. Afterunloading, inspect your firearm for possible damage or obstructions inthe chamber or bore.

Upon firing, the pressure generated by the powder combustion will push the boltto its rearward position, extracting and ejecting the fired cartridge case. Uponreaching its most rearward position, the bolt will have recocked the hammer, andthe bolt recoil spring will then push the bolt forward, feeding a new cartridge fromthe top of the clip magazine and chambering it. The firearm will again be readyto fire. This cycle will be repeated every time the trigger is pulled until there areno cartridges remaining in the magazine. If the trigger is pulled again, the firearmwill then fire the live cartridge remaining in the firearm’s chamber. After this lastcartridge has been fired, the clip magazine follower is designed to keep the boltin the open position.As the firearm was designed to fire semi-automatic only, it is mandatory to relievepressure on the trigger after each shot in order to allow the disconnector to againconnect the trigger to the firing mechanism.After the last cartridge has been fired, the clip magazine follower is designed tokeep the bolt in the open position. (Fig. 6)

Move the safety button fully to the right to the “ON” (SAFE) position andvisually and physically inspect the chamber and magazine to ensure thatthere are no live cartridges present.

12

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 12

If the magazine is withdrawn from the firearm, the bolt will close; however, it is eas-ier to remove the magazine from the firearm if the bolt is locked at its most rear-ward position by its operating handle.

Before inserting a new loaded magazine into the firearm move the safetybutton fully to the right to the “ON” (SAFE) position.

If the bolt is locked in its open position by the operating handle, to chamber a car-tridge, insert a loaded magazine, pull the operating handle to the rear and out-ward and let the bolt move freely forward.

The firearm is now loaded and will fire if the trigger is pressed.

To interrupt shooting and unload the firearm, keep the muzzle pointed in a safedirection, move the safety button fully to the right to the “ON” (SAFE) position,remove the magazine and pull the bolt to its most rearward position, extractingand ejecting the cartridge in the chamber. Push the operating handle inward tohold the bolt open. (Fig. 6 & 7)

If desired or necessary, the firearm can be single loaded with a cartridge directlyinto the chamber. Pull the bolt rearwards and lock it to the receiver using the oper-ating handle. Move the safety button fully to the right to the “ON” (SAFE) positionand keeping the muzzle pointed in a safe direction, insert a cartridge directly intothe chamber and close the bolt. It will be easier to single load the firearm if themagazine is removed from the firearm.

The firearm is now loaded and will fire when the trigger is pulled with thesafety in the “OFF” (FIRE) position whether or not the magazine is in thefirearm.

As a safety procedure, every time shooting is interrupted or the firearm isunloaded, move the safety button fully to the right to the “ON” (SAFE) position,and move the bolt to the open (rearward) position and locked open by pushinginward on the operating handle.

DISASSEMBLY FOR CLEANING AND LUBRICATION

Remove the magazine.Pull the operating handle fully rearward to extractand eject any cartridge that might be in the chamber. Push the operatinghandle inward to lock the bolt in the open position. Move the safety but-ton fully to the right to the “ON” (SAFE) position.

Visually and physically inspect the chamber and inside the receiver to becertain the firearm is unloaded. Wear eye protection during disassemblyand cleaning to protect your eyes from oil spatter or spring loaded com-ponents.

Remove the barrel/receiver assembly from the stock.

MODELS WITH 702 PLINKSTER STOCKS: Using a No. 2 Phillipsscrewdriver, remove the two takedown screws located at the front andback of the trigger guard and pull the barrel/receiver assembly awayfrom the stock.

13

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 13

14

Fig. 10

Remove the #2 PlastiteTM screw and the right magazine release lever.The left magazine release lever can now be removed. Remove the #4PlastiteTM screws from the right halves of the forearm and receiver shell.(Fig. 11) Remove one side of the forearm, and then the other. The slingswivel can be slid off of the barrel. Now separate the receiver shellsfrom one another. The action assembly can now be removed from thereceiver shell.

MODELS WITH AR STYLE STOCKS: First remove the stock bolt fromboth sides of the tactical stock assembly. Remove the stock assemblyfrom the receiver shells. Remove the nut from the scope mounting railand lift the rail from the hole in the top of the carry handle. Insert a 5/32”Allen wrench into the hole in the pistol grip and the front of receivershells and engage with the heads of the takedown screws. (Fig. 10)Loosen the takedown screws, but do not fully remove.

Fig. 11

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 14

TO DISASSEMBLE THE FIREARM

With a pin punch or similiar tool, remove the two trigger housing retaining pinslocated at the side of the receiver (Fig. 12). Be careful not to damage the blackfinish on the parts.

While holding the operating handle fully rearward, carefully lift the trigger housingfrom the receiver (Fig. 13).

Allow the operating handle to SLOWLY move fully forward. Remove the boltbuffer from the rear of the receiver (Fig. 14).

Fig. 13

15

Fig. 12

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 15

Fig. 14

Using the operating handle, pull the bolt rearward until you can insert your fore-finger in front of the bolt. Be careful not to pinch your finger between the bolt faceand the barrel. Lift up slightly on the bolt with your forefinger and remove the bolthandle through the ejection port.

Fig. 15

Continue to lift up on the bolt while slowly letting it come forward to rest againstthe barrel. Reposition your forefinger grip and insert a finger through the ejectionport (Fig. 16). Maneuver the bolt assembly completely up and out of the receiver.Remove the bolt spring and bolt spring guide rod (Fig. 17a).

Fig. 16

No further disassembly should be done by the owner. If service is required, con-tact the factory authorized service center or a qualified gunsmith.

16

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 16

CLEANING AND LUBRICATION

NOTE: Semi-automatic firearms require more frequent cleaning than those manually operated.

With proper care, your Mossberg Int’l.TM rifle will provide you with years of depend-able service. Your firearm should be inspected and cleaned after every 200 roundsto ensure that it remains in good condition. However, unusually dusty, dirty, orharsh weather conditions, or use of dirty ammunition which leaves significant pow-der residue may necessitate more frequent cleaning. Clean your firearm as soonas possible after use. This is especially important if your firearm has been exposedto moisture.

Follow the instructions and use the equipment provided in a quality firearm cleaning kit.

All metal parts should be cleaned with an appropriate firearm cleaning solventand lightly lubricated with gun oil. Over lubrication should be avoided. Use onlylubricants specifically designed for firearms. Avoid the use of abrasives, whichmay damage the metal finish.

Normal use requires only that the mechanisms be free of excessive shootingresidue. Very little lubrication other than a light oiling of external surfaces is neededto prevent rust.

If the firearm is to be stored for a long period of time it should be thoroughlycleaned and oiled. Do not plug the barrel or store the firearm in a case that willabsorb lubricants.

THE TRIGGER HOUSING ASSEMBLY, BOLT ASSEMBLY AND RECEIVERIn the trigger housing, special attention should be given to the bolt sliding surfacesand to the feeding ramp. The bolt and the receiver must be carefully cleaned andfree of any solid residues. Solid residues in the bolt/receiver areas may preventthe bolt from closing properly and a misfire may result.

THE BARRELAs it is not possible to clean the barrel from breech to muzzle, be very careful whileintroducing the cleaning rod into the barrel muzzle, thus avoiding any damage tothe barrel crown.

Use a .22 caliber brass cleaning brush, moistened with solvent, scrubbing the bar-rel several times.

Use a .22 caliber cleaning rod with a clean cloth patch to wipe the bore dry. Repeatseveral times, using a new patch each time, until the barrel is clean and shows nosigns of residue.

Final wipe with a quality gun oil moistened patch. Do not over-lubricate, a light filmis recommended.

Be sure not to leave cleaning patches or excessive oil or grease in thebore and make sure the barrel is free of obstructions and excessive lubri-cant after cleaning as they can create dangerous obstructions, resultingin damage to the firearm and/or serious personal injury to you or thosearound you.

17

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 17

TO REASSEMBLE THE FIREARM

Assemble the bolt spring and bolt spring guide rod into the bolt assembly (Fig.17a and 17b).

Fig. 17a Fig. 17b.

Insert the assembly into the receiver, bolt face first (Fig. 18a). Insert the operatinghandle through the ejection port to line up with the operating handle slot in the bolt(Fig. 18a).

Fig. 18a Fig. 18b

Compress the bolt spring and lower the bolt assembly into the receiver (Fig. 18b).As the bolt is lowered into the receiver make sure the operating handle does notmove out of position. Compress the bolt recoil spring until the end of the boltspring guide pops into the blind hole in the rear of the receiver.

Insert the bolt buffer (Fig. 19). Make sure it is oriented as shown in figure 14.

18

Fig. 19

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 18

Using the operating handle, push the bolt fully rearward. While holding the boltfully rearward, place the trigger housing assembly into the receiver (Fig. 20).Allow the bolt to SLOWLY come fully forward. Align the holes in the trigger hous-ing with the holes in the receiver, and insert the two trigger housing retaining pins(Fig. 12).

MODELS WITH 702 PLINKSTER STOCK: Place the action into the stock andreinstall the two take-down screws located in the stock (one to the rear of the trig-ger guard and one in front of the magazine).

MODELS WITH AR STYLE STOCK: For models with AR style stocks, reversethe procedure outlined in the “Disassembly for Cleaning and Lubrication” sectionof this manual. Ensure that the sling swivel is in place on the barrel prior toreassembly. Tighten the PlastiteTM screws until snug. Do not over-tighten thePlastiteTM screws as this can damage the forend and/or receiver shells. Ensurethat the front and rear takedown screws (Fig. 10) are securely tightened.

Check to ensure the firearm is functioning properly, see “Function Testing” before using live ammunition.

FUNCTION TESTING

AFTER PERFORMING ANY WORK ON YOUR FIREARM SUCH ASCLEANING, DISASSEMBLY OR INSTALLATION OF AN ACCESSORY:

a. Keep the muzzle pointed in a safe direction, remove the magazineand pull the operating handle fully rearward to open the action, andvisually and physically check the chamber and inside the receiver tobe certain the firearm is unloaded.

b. Move the safety button fully to the right to the “ON” (SAFE) position.

KEEP THE MUZZLE POINTED IN A SAFE DIRECTION AT ALL TIMESTHROUGHOUT THE FOLLOWING STEPS! FAILURE TO DO SOCOULD RESULT IN SERIOUS INJURY OR DEATH IF THE FIREARMHAS NOT BEEN PROPERLY UNLOADED, AND FIRES WHILE YOUARE TESTING ITS FUNCTION!

Close the action and leave the safety in the “ON” (SAFE) position. Pull the triggerrearward fully. The hammer should not fall (No Fire).

19

Fig. 20

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 19

Remove your finger from the trigger. Move the safety to the “OFF” (FIRE) position.The hammer should not fall (No Fire).Leave the safety in the “OFF” (FIRE) position.

Pull the trigger rearward. The hammer should fall (FIRE).

Open the action by pulling the operating handle fully rearward and push the operating handle in to lock the bolt in the open position. Move the safety buttonfully to the right to the “ON” (SAFE) position.

IF YOUR FIREARM DOES NOT PERFORM AS DESCRIBED IN ANY OFTHE ABOVE STEPS, CONTACT THE PRODUCT SERVICE CENTERIMMEDIATELY. DO NOT ATTEMPT TO LOAD OR USE THE FIREARM.

PRECAUTIONS AND CARE WITH YOUR FIREARM

When you store your firearm, make sure that the magazine and the chamber areempty.

Operation of the firearm and/or repeated disassembly may cause screws toloosen. Refer to the section of the manual TO REASSEMBLE THE FIREARMand check all screws including the Takedown Screws (Figure 10), the #4PlastiteTM Screws (Figure 11), the #2 PlastiteTM Screw, and the Stock Bolt periodi-cally and at each cleaning interval to ensure the continued accuracy and safeoperation of your firearm. Care should be taken, especially with the #2 PlastiteTMScrew that attaches the Magazine Release, not to over-tighten any screws as thismay cause screws to strip.

Handling leaves moisture prints that can cause metal parts to rust. Abruptchanges in temperature cause condensation and moisture. Wipe the barrel andother metal parts with light oil after handling.

SIGHT ADJUSTMENT

BEFORE MAKING ANY SIGHT ADJUSTMENTS:

a. Keep the muzzle pointed in a safe direction, remove the magazineand lock the operating handle in the open position (Fig 6 & 7), andvisually and physically check the chamber and inside the receiver tobe certain the firearm is unloaded.

b. Move the safety button fully to the right to the “ON” (SAFE) position.

ELEVATION ADJUSTMENT ON MODELS WITHOUT AR STYLE STOCK: To raisethe point of impact, raise the rear sight by turning the top adjustment screw clock-wise. To lower the point of impact, lower the rear sight by turning the top adjustmentscrew counter-clockwise.

Windage adjustment: To move the point of impact to the right, turn the side adjust-ment screw clockwise. To shift the point of impact to the left, turn the side adjust-ment screw counter-clockwise.

Remember: Move the rear sight in the same direction you would like the shot tomove. For example, if the point of impact is low and left from the point of aim,

20

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 20

21

move the rear sight upward and to the right. (Fig. 21)

Fig. 21

Raise

Lower

Right

Left

Fig. 22

Left Right

Raise Lower

ELEVATION ADJUSTMENT ON MODELS WITH AR STYLE STOCK: To raise thepoint of impact, raise the rear sight by turning the elevation knob clockwise. Tolower the point of impact, lower the rear sight by turning the elevation knob count-er-clockwise.

Windage adjustment: To move the point of impact to the right, turn the windageadjustment screw clockwise. To shift the point of impact to the left, turn thewindage adjustment screw counter-clockwise.

Remember: Move the rear sight in the same direction you would like the shot tomove. For example, if the point of impact is low and left from the point of aim,move the rear sight upward and to the right. (Fig. 22)

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 21

SERVICE INSTRUCTIONS

Should your firearm, or any component of your firearm require service, kindly shipyour entire firearm (please do not send components only), via your chosen carrier, postage paid (we do not accept C.O.D. shipments), following these instructions:Repairs in the U.S.For faster repair service, please start the process by filling out our Service RequestForm online at http://www.mossberg.com/service prior to shipping your firearm.

Make absolutely certain your firearm is unloaded.•Do not send ammunition with your firearm.•Remove all accessories from your firearm such as scopes, slings,•mounts, etc.Ship your firearm in a suitable container, packaging it securely to •prevent parts from shifting and/or damage during shipping.Include a note with a clear description of the service you wish us to •perform, your complete return shipping address (no P.O. boxesplease), your daytime telephone number and your e-mail address (ifavailable). It is advisable to place your correspondence inside your shipping •container when shipping.

SHIPPING ADDRESSMossberg Product Service Center1001 Industrial BoulevardEagle Pass, TX 78852

If you have any service related questions, please contact the ProductService Center at (800) 363-3555 or service@mossberg.com.

TO ORDER PARTSTo order parts from the Product Service Center, you can fax, phone,email or mail your order to one of the below numbers/addresses.

Fax Number: (203) 230-5420Phone Number: (800) 363-3555Email Address: service@mossberg.comMailing Address: Mossberg Product Service Center

1001 Industrial BoulevardEagle Pass, TX 78852Attn: Order Department

Please provide your name, address, city, state, zip, your daytime phone numberand e-mail address. We will need the Model #, Serial #, Gauge/Caliber, Finish, Part # and Part Name. We have a $7.50 (U.S.) minimum parts order charge. Weaccept most major credit cards, money orders, and bank drafts.

Service outside of the U.S.A.For Mossberg International firearm parts and service requirements outside of theUnited States, customers are requested to contact the closest Mossberg Internationalstocking dealer/distributor.

22

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 22

23

MOSSBERG INTERNATIONAL WARRANTY702/715T™ .22 CALIBER SEMI-AUTOMATIC RIFLE

ONE (1) YEAR LIMITED WARRANTYLimited Warranty: Mossberg International, Inc. (“Mossberg”) warrants to you, the original retailpurchaser of a new Mossberg Int’l.TM .22-caliber semi-automatic rifle (the “Mossberg firearm”), thatthe Mossberg firearm will be free of defects in material or manufacture for a period of one (1)year from the date of your purchase of the new Mossberg firearm (the “Warranty Period”) in theUnited States or Canada. This is the only express warranty on the Mossberg firearm.

MOSSBERG MAKES NO OTHER WARRANTIES OF ANY KIND OR CONDITIONS, INCLUD-ING, BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESSFOR A PARTICULAR PURPOSE.

This Limited Warranty gives you specific legal rights, and you may have other rights that varyfrom State to State.

Purchaser’s Remedy: During the Warranty Period, Mossberg will, at its sole option, (1) repair the Mossberg firearm or any part thereof that, upon examination and testing by Mossberg, doesnot conform to the Limited Warranty without charge to you for parts or labor, or (2) replace theMossberg firearm with a new or similar model. THIS REMEDY SHALL BE YOUR EXCLUSIVEAND SOLE REMEDY FOR ANY BREACH OF WARRANTY. MOSSBERG SHALL NOT BERESPONSIBLE FOR ANY OTHER EXPENSES, LOSSES OR INCONVENIENCE THAT YOUMAY SUSTAIN AS A RESULT OF THE PURCHASE, USE, MALFUNCTION OR DEFECTIVECONDITION OF THE MOSSBERG FIREARM. Mossberg reserves the right to inspect, examineand/or test the Mossberg firearm to assess any claim made under the Limited Warranty.

EXCLUSIONS: THIS WARRANTY DOES NOT COVER THE COSMETIC APPEARANCE OFTHE MOSSBERG FIREARM OR ANY DAMAGE CAUSED BY:

(1) NORMAL WEAR AND TEAR;(2) FAILURE TO PERFORM PROPER CARE AND MAINTENANCE;(3) ACCIDENTS, ABUSE OR NEGLECT;(4) BARREL OR BORE OBSTRUCTIONS; (5) FAILURE TO FOLLOW THE INSTRUCTIONS AND WARNINGS THAT ACCOMPANY

THE MOSSBERG FIREARM; OR(6) THE USE OF DEFECTIVE, NON-SAAMI STANDARD, REMANUFACTURED, HAND-

LOADED, AND/OR RELOADED AMMUNITION.

IN ADDITION, ANY UNAUTHORIZED REPAIRS, ALTERATIONS OR MODIFICATIONS TOTHE MOSSBERG FIREARM WILL AUTOMATICALLY VOID THE LIMITED WARRANTY.

LIMITATION OF DAMAGES: EXCEPT WHERE PROHIBITED BY LAW, MOSSBERG WILL NOT BE LIABLE FOR ANY LOSS OR DAMAGE WHATSOEVER ARISING FROM THE USE OF THISMOSSBERG FIREARM, WHETHER DIRECT, INDIRECT, SPECIAL, INCIDENTAL, CONSEQUEN-TIAL OR PUNITIVE, REGARDLESS OF THE LEGAL THEORY ASSERTED, INCLUDING CON-TRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. SOME JURISDICTIONS DO NOTALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSIONOF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOTAPPLY TO YOU.

Warranty Service: To obtain service under this Limited Warranty, you must follow the instructionsfound in the “Service Instructions” section of the Owner’s Manual and return the Mossberg firearmto the authorized Product Service Center. You are responsible for all shipping costs to theProduct Service Center. Mossberg will not accept COD shipments of any Mossberg firearm forservice. After repair or replacement, the Mossberg firearm or a similar model will be returned toyou, return postage paid by Mossberg. If we replace the Mossberg firearm, we will keep thefirearm that you returned to Mossberg.

Modification of Warranty: No agent, representative, distributor, or authorized dealer of Mossbergfirearms has any authority to modify the terms or conditions of the Limited Warranty in any way.The Limited Warranty may only be modified in writing by an authorized officer of Mossberg.

THIS LIMITED WARRANTY IS EFFECTIVE JANUARY 1, 2003.

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 23

24

Item No. Description

1 Stock assembly - standard

2 Stock assembly - thumbhole

3 Take down screw (2 pieces)

*4 Receiver and barrel assembly

5 Operating handle

*6 Bolt assembly

7 Bolt recoil spring

8 Bolt recoil spring guide

Item No. Description

9 Bolt buffer

10 Pin 5.0 x 26.0 mm (2 pieces)

11 Rear sight assembly

12 Rear sight screw (2 pieces)

13 Front sight assembly

14 Front sight screw (2 pieces)

*15 Trigger guard assembly

16 Magazine Assembly

PARTS LIST

EXPLODED VIEW

1

2

3

47

6

9

8

10

11

1213

14

16

15

Items marked with an asterisk (*) are reserved for qualified gunsmiths only.

5

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 24

EXPLODED VIEW702 With AR Shell

1

2

3

5

4

6

10

8

9

7

16

15

14 13

12

11

Item No. Description

1 Receiver shell right

2 Receiver shell left

3 Forearm right

4 Forearm left

5 Tactical stock assembly

6 Accessory rail (2 pieces)

7 Magazine release lever right

8 Magazine release lever left

9 Barrel band sling swivel

10 Rear sight elevation knob

11 Rear sight windage knob

Item No. Description

12 Rear sight elevation base

13 Rear sight aperture

14 Flat washer

15 Wave washer

16 Magazine Assembly

*17 Receiver and barrel assembly

18 Rear take down screw

19 Front take down screw

20 #2 PlastiteTM screw

21 #4 PlastiteTM screw (18 pieces)

22 Stock bolt (2 Pieces)

23 Scope mounting rail

PARTS LIST

Items marked with an asterisk (*) are reserved for qualified gunsmiths only.

17

18

25

1921

20

22

23

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 25

NOTES

26

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 26

NOTES

27

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 27

From the time an individual picks up a firearm, that individual shooterbecomes a part of a system over which he or she has complete control.He or she is the only part of the system that can make a gun safe – orunsafe. Hunting and target shooting are among the safest of all sports.This booklet is intended to make them even safer – by re-emphasizingand reaffirming the basics of safe gun handling and storage and byreminding each individual shooter that he or she is the key to firearmssafety. You can help meet this responsibility by enrolling in hunter safetyor shooting safety courses. You must constantly stress safety when han-dling firearms, especially to children and non-shooters. Newcomers inparticular must be closely supervised when handling firearms with whichthey may not be acquainted. Don’t be timid when it comes to gun safety.If you observe anyone violating any safety precautions, you have an obli-gation to suggest safer handling practices, such as those in this booklet.Please read these rules carefully and follow the safety procedures out-lined. Firearms safety is up to you. Make no mistake about it.

1. ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION

2. FIREARMS SHOULD BE UNLOADED WHEN NOT ACTUALLY IN USE

3. DON’T RELY ON YOUR GUN’S “SAFETY”

4. BE SURE OF YOUR TARGET AND WHAT’S BEYOND IT

5. USE CORRECT AMMUNITION

6. IF YOUR GUN FAILS TO FIRE WHEN THE TRIGGER IS PULLED, HANDLE WITH CARE

7. ALWAYS WEAR EYE AND EAR PROTECTION WHEN SHOOTING

8. BE SURE THE BARREL IS CLEAR OF OBSTRUCTIONS BEFORE SHOOTING

9. DO NOT ALTER OR MODIFY YOUR GUN, AND HAVE GUNS SERVICED REGULARLY

10. LEARN THE MECHANICAL AND HANDLING CHARACTERISTICS OF THE FIREARM YOU ARE USING

Courtesy of Sporting Arms and Ammunition Manufacturers’ Institute, Inc.

FIREARMS SAFETY DEPENDS ON YOU.MAKE NO MISTAKE ABOUT IT!

17928 702 Plinkster_#51890 2/15/18 1:29 PM Page 28