osha part 1926 safety and health regulations for construction

OSHA PART 1926 SAFETY AND HEALTH REGULATIONS

FOR CONSTRUCTIONSubpart I - Tools - Hand and

Power

DirectionsPlease place the PowerPoint program or viewer in presentation mode. You can accomplish this by clicking on the Slideshow Tab located at the top of the Tools Bar and then selecting “From the Beginning”Click on each slide to transition to the next slide. After reading all the slide, complete the exam. Thank You

1926.300 General Requirements (a) Condition of tools All hand and power tools and similar

equipment, whether furnished by the employer or the employee, shall be maintained in a safe condition.

(b) Guarding (b)(1) When power operated tools are designed to

accommodate guards, they shall be equipped with such guards when in use

(b)(2) Belts, gears, shafts, pulleys, sprockets, spindles, drums,

fly wheels, chains, or other reciprocating, rotating or moving parts of equipment shall be guarded if such parts are exposed to contact by employees or otherwise create a hazard. Guarding shall meet the requirements as set forth in American National Standards Institute, B15.1-1953 (R1958), Safety Code for Mechanical Power-Transmission Apparatus

(b)(3) "Types of guarding." One or more methods

of machine guarding shall be provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks. Examples of guarding methods are - barrier guards, two-hand tripping devices, electronic safety devices, etc.

(b)(4) "Point of operation guarding" (b)(4)(i) Point of operation is the area on a machine where work is

actually performed upon the material being processed (b)(4)(ii) The point of operation of machines whose operation

exposes an employee to injury, shall be guarded. The guarding device shall be in conformity with any appropriate standards therefore, or, in the absence of applicable specific standards, shall be so designed and constructed as to prevent the operator from having any part of his body in the danger zone during the operating cycle

(b)(4)(iii) Special hand tools for placing and

removing material shall be such as to permit easy handling of material without the operator placing a hand in the danger zone. Such tools shall not be in lieu of other guarding required by this section, but can only be used to supplement protection provided.

(b)(4)(iv) The following are some of the machines which

usually require point of operation guarding: (b)(4)(iv)(a)

Guillotine cutters (b)(4)(iv)(b)

Shears (b)(4)(iv)(c)

Alligator shears (b)(4)(iv)(d)

Powered presses

(b)(4)(iv)(e) Milling machines

(b)(4)(iv)(f) Power saws

(b)(4)(iv)(g) Jointers

(b)(4)(iv)(h) Portable power tools

(b)(4)(iv)(i) Forming rolls and cylinders

(b)(5) -"Exposure of blades." When the periphery of

the blades of a fan is less than 7 feet (2.128 m) above the floor or working level, the blades shall be guarded. The guard shall have openings no larger than 1/2 inch (1.27 cm)

(b)(6) -"Anchoring fixed machinery." Machines

designed for a fixed location shall be securely anchored to prevent walking or moving

(b)(7) "Guarding of abrasive wheel machinery - exposure

adjustment." Safety guards of the types described in paragraphs (b)(8) and (9) of this section, where the operator stands in front of the opening, shall be constructed so that the peripheral protecting member can be adjusted to the constantly decreasing diameter of the wheel. The maximum angular exposure above the horizontal plane of the wheel spindle as specified in paragraphs (b)(8) and (9) of this section shall never be exceeded, and the distance between the wheel periphery and the adjustable tongue or the end of the peripheral member at the top shall never exceed 1/4 inch (0.635 cm)

(b)(8) Bench and floor stands. The angular exposure of

the grinding wheel periphery and sides for safety guards used on machines known as bench and floor stands should not exceed 90 deg. or one-fourth of the periphery. This exposure shall begin at a point not more than 65 deg. above the horizontal plane of the wheel spindle

Whenever the nature of the work requires contact with the wheel below the horizontal plane of the spindle, the exposure shall not exceed 125 deg.

(b)(9)Cylindrical grinders. The maximum angular exposure of the grinding wheel periphery and sides for safety guards used on cylindrical grinding machines shall not exceed 180 deg.. This exposure shall begin at a point not more than 65 deg. above the horizontal plane of the wheel spindle

(c) Personal protective equipmentEmployees using hand and power tools and exposed to the hazard of falling, flying, abrasive, and splashing objects, or exposed to harmful dusts, fumes, mists, vapors, or gases shall be provided with the particular personal protective equipment necessary to protect them from the hazard. All personal protective equipment shall meet the requirements and be maintained according to Subparts D and E of this part

(d) Switches(d)(1)All hand-held powered platen sanders, grinders with wheels 2-inch diameter or less, routers, planers, laminate trimmers, nibblers, shears, scroll saws, and jigsaws with blade shanks one-fourth of an inch wide or less may be equipped with only a positive "on-off" control(d)(2)All hand-held powered drills, tappers, fastener drivers, horizontal, vertical, and angle grinders with wheels greater than 2 inches in diameter, disc sanders, belt sanders, reciprocating saws, saber saws, and other similar operating powered tools shall be equipped with a momentary contact "on-off" control and may have a lock-on control provided that turnoff can be accomplished by a single motion of the same finger or fingers that turn it on

(d)(3) All other hand-held powered tools, such as circular saws,

chain saws, and percussion tools without positive accessory holding means, shall be equipped with a constant pressure switch that will shut off the power when the pressure is released

(d)(4) The requirements of this paragraph shall become effective

on July 15, 1972 (d)(5) Exception: This paragraph does not apply to concrete

vibrators, concrete breakers, powered tampers, jack hammers, rock drills, and similar hand operated power tools

[58 FR 35175, June 30, 1993; 61 FR 9227, March 7, 1996]

1926.301 Hand Tools (a) Employers shall not issue or permit the use of unsafe

hand tools (b) Wrenches, including adjustable, pipe, end, and socket

wrenches shall not be used when jaws are sprung to the point that slippage occurs

(c) Impact tools, such as drift pins, wedges, and chisels,

shall be kept free of mushroomed heads (d) The wooden handles of tools shall be kept free of

splinters or cracks and shall be kept tight in the tool

1926.302 Power Operated Hand Tools

(a) Electric power-operated tools (a)(1) Electric power operated tools shall either

be of the approved double-insulated type or grounded in accordance with Subpart K of this part

(a)(2) The use of electric cords for hoisting or

lowering tools shall not be permitted

(b) Pneumatic power tools (b)(1) Pneumatic power tools shall be secured to the hose or whip by

some positive means to prevent the tool from becoming accidentally disconnected

(b)(2) Safety clips or retainers shall be securely installed and

maintained on pneumatic impact (percussion) tools to prevent attachments from being accidentally expelled

(b)(3) All pneumatically driven nailer, staplers, and other similar

equipment provided with automatic fastener feed, which operate at more than 100 p.s.i. pressure at the tool shall have a safety device on the muzzle to prevent the tool from ejecting fasteners, unless the muzzle is in contact with the work surface

(b) Pneumatic power tools (b)(4) Compressed air shall not be used for cleaning purposes except where

reduced to less than 30 p.s.i. and then only with effective chip guarding and personal protective equipment which meets the requirements of Subpart E of this part. The 30 p.s.i. requirement does not apply for concrete form, mill scale and similar cleaning purposes

(b)(5) The manufacturer’s safe operating pressure for hoses, pipes, valves,

filters, and other fittings shall not be exceeded (b)(6) The use of hoses for hoisting or lowering tools shall not be permitted (b)(7) All hoses exceeding 1/2-inch inside diameter shall have a safety

device at the source of supply or branch line to reduce pressure in case of hose failure

(b) Pneumatic power tools (b)(8) Airless spray guns of the type which atomize paints and fluids at

high pressures (1,000 pounds or more per square inch) shall be equipped with automatic or visible manual safety devices which will prevent pulling of the trigger to prevent release of the paint or fluid until the safety device is manually released

(b)(9) In lieu of the above, a diffuser nut which will prevent high pressure,

high velocity release, while the nozzle tip is removed, plus a nozzle tip guard which will prevent the tip from coming into contact with the operator, or other equivalent protection, shall be provided

(b)(10) "Abrasive blast cleaning nozzles." The blast cleaning nozzles shall

be equipped with an operating valve which must be held open manually. A support shall be provided on which the nozzle may be mounted when it is not in use

(c) Fuel powered tools (c)(1) All fuel powered tools shall be stopped while

being refueled, serviced, or maintained, and fuel shall be transported, handled, and stored in accordance with Subpart F of this part

(c)(2) When fuel powered tools are used in enclosed

spaces, the applicable requirements for concentrations of toxic gases and use of personal protective equipment, as outlined in Subparts D and E of this part, shall apply

(d) Hydraulic power tools

(d)(1) The fluid used in hydraulic powered tools shall be

fire-resistant fluids approved under Schedule 30 of the U.S. Bureau of Mines, Department of the Interior, and shall retain its operating characteristics at the most extreme temperatures to which it will be exposed

(d)(2) The manufacturer’s safe operating pressures for

hoses, valves, pipes, filters, and other fittings shall not be exceeded

(e) Powder-actuated tools (e)(1) Only employees who have been trained in the operation of the

particular tool in use shall be allowed to operate a powder-actuated tool

(e)(2) The tool shall be tested each day before loading to see that safety

devices are in proper working condition. The method of testing shall be in accordance with the manufacturer’s recommended procedure

(e)(3) Any tool found not in proper working order, or that develops a

defect during use, shall be immediately removed from service and not used until properly repaired

(e)(4) Personal protective equipment shall be in accordance with Subpart

E of this part

(e) Powder-actuated tools (e)(5) Tools shall not be loaded until just prior to the intended firing

time. Neither loaded nor empty tools are to be pointed at any employees. Hands shall be kept clear of the open barrel end

(e)(6) Loaded tools shall not be left unattended (e)(7) Fasteners shall not be driven into very hard or brittle materials

including, but not limited to, cast iron, glazed tile, surface-hardened steel, glass block, live rock, face brick, or hollow tile

(e)(8) Driving into materials easily penetrated shall be avoided unless

such materials are backed by a substance that will prevent the pin or fastener from passing completely through and creating a flying missile hazard on the other side

(e) Powder-actuated tools (e)(9) No fastener shall be driven into a spalled area caused by an

unsatisfactory fastening (e)(10) Tools shall not be used in an explosive or flammable

atmosphere (e)(11) All tools shall be used with the correct shield, guard, or

attachment recommended by the manufacturer (e)(12) Powder-actuated tools used by employees shall meet all other

applicable requirements of American National Standards Institute, A10.3- 1970, Safety Requirements for Explosive-Actuated Fastening Tools

[53 FR 36009, Sept. 16, 1988; 58 FR 35175, June 30, 1993]

1926.303 Abrasive Wheels and Tools

(a) Power All grinding machines shall be supplied with

sufficient power to maintain the spindle speed at safe levels under all conditions of normal operation.

(b) Guarding (b)(1) Grinding machines shall be equipped with safety

guards in conformance with the requirements of American National Standards Institute, B7.1-1970, Safety Code for the Use, Care and Protection of Abrasive Wheels, and paragraph (d) of this section.


(b)(2) "Guarding design." The safety guard shall cover the spindle end,

nut, and flange projections. The safety guard shall be mounted so as to maintain proper alignment with the wheel, and the strength of the fastenings shall exceed the strength of the guard, except:

(b)(2)(i) Safety guards on all operations where the work provides a

suitable measure of protection to the operator, may be so constructed that the spindle end, nut, and outer flange are exposed; and where the nature of the work is such as to entirely cover the side of the wheel, the side covers of the guard may be omitted and

(b)(2)(ii) The spindle end, nut, and outer flange may be exposed on

machines designed as portable saws


(c) Use of abrasive wheels (c)(1) Floor stand and bench mounted abrasive wheels, used for external

grinding, shall be provided with safety guards (protection hoods). The maximum angular exposure of the grinding wheel periphery and sides shall be not more than 90 degrees, except that when work requires contact with the wheel below the horizontal plane of the spindle, the angular exposure shall not exceed 125 deg. In either case, the exposure shall begin not more than 65 deg. above the horizontal plane of the spindle. Safety guards shall be strong enough to withstand the effect of a bursting wheel.

(c)(2) Floor and bench-mounted grinders shall be provided with work

rests which are rigidly supported and readily adjustable. Such work rests shall be kept at a distance not to exceed one-eighth inch from the surface of the wheel.


(c)(3) Cup type wheels used for external grinding shall be protected by

either a revolving cup guard or a band type guard in accordance with the provisions of the American National Standards Institute, B7.1-1970 Safety Code for the Use, Care, and Protection of Abrasive Wheels. All other portable abrasive wheels used for external grinding, shall be provided with safety guards (protection hoods) meeting the requirements of paragraph (c)(5) of this section, except as follows:

(c)(3)(i) When the work location makes it impossible, a wheel equipped

with safety flanges, as described in paragraph (c)(6) of this section, shall be used

(c)(3)(ii) When wheels 2 inches or less in diameter which are securely

mounted on the end of a steel mandrel are used


(c)(4) Portable abrasive wheels used for internal grinding

shall be provided with safety flanges (protection flanges) meeting the requirements of paragraph (c)(6) of this section, except as follows:

(c)(4)(i) When wheels 2 inches or less in diameter which are

securely mounted on the end of a steel mandrel are used

(c)(4)(ii) If the wheel is entirely within the work being ground

while in use


(c)(5) When safety guards are required, they shall be so mounted as to

maintain proper alignment with the wheel, and the guard and its fastenings shall be of sufficient strength to retain fragments of the wheel in case of accidental breakage. The maximum angular exposure of the grinding wheel periphery and sides shall not exceed 180 deg

(c)(6) When safety flanges are required, they shall be used only with

wheels designed to fit the flanges. Only safety flanges, of a type and design and properly assembled so as to ensure that the pieces of the wheel will be retained in case of accidental breakage, shall be used

(c)(7) All abrasive wheels shall be closely inspected and ring-tested before

mounting to ensure that they are free from cracks or defects


(c)(8) Grinding wheels shall fit freely on the spindle and

shall not be forced on. The spindle nut shall be tightened only enough to hold the wheel in place

(c)(9) All employees using abrasive wheels shall be

protected by eye protection equipment in accordance with the requirements of Subpart E of this part, except when adequate eye protection is afforded by eye shields which are permanently attached to the bench or floor stand

1926.304 Woodworking Tools

(d) Guarding All portable, power-driven circular saws shall be equipped with guards

above and below the base plate or shoe. The upper guard shall cover the saw to the depth of the teeth, except for the minimum arc required to permit the base to be tilted for bevel cuts. The lower guard shall cover the saw to the depth of the teeth, except for the minimum arc required to allow proper retraction and contact with the work. When the tool is withdrawn from the work, the lower guard shall automatically and instantly return to the covering position

(e) Personal protective equipment All personal protective equipment provided for use shall conform to

Subpart E of this part (f) Other requirements All woodworking tools and machinery shall meet other applicable

requirements of American National Standards Institute, 01.1-1961, Safety Code for Woodworking Machinery


(g) "Radial saws.“ (g)(1) The upper hood shall completely enclose the upper portion of the

blade down to a point that will include the end of the saw arbor. The upper hood shall be constructed in such a manner and of such material that it will protect the operator from flying splinters, broken saw teeth, etc., and will deflect sawdust away from the operator. The sides of the lower exposed portion of the blade shall be guarded to the full diameter of the blade by a device that will automatically adjust itself to the thickness of the stock and remain in contact with stock being cut to give maximum protection possible for the operation being performed.

(h) "Hand-fed crosscut table saws" (h)(1) Each circular crosscut table saw shall be guarded by a hood which

shall meet all the requirements of paragraph (i)(1) of this section for hoods for circular ripsaws


(i) "Hand-fed ripsaws" (i)(1) Each circular hand-fed ripsaw shall be guarded by a hood which shall

completely enclose the portion of the saw above the table and that portion of the saw above the material being cut. The hood and mounting shall be arranged so that the hood will automatically adjust itself to the thickness of and remain in contact with the material being cut but it shall not offer any considerable resistance to insertion of material to saw or to passage of the material being sawed. The hood shall be made of adequate strength to resist blows and strains incidental to reasonable operation, adjusting, and handling, and shall be so designed as to protect the operator from flying splinters and broken saw teeth. It shall be made of material that is soft enough so that it will be unlikely cause tooth breakage. the hood shall be so mounted as to insure that its operation will be positive, reliable, and in true alignment with the saw; and the mounting shall be adequate in strength to resist any reasonable side thrust or other force tending to throw it out of line.

[58 FR 35175, June 30, 1993; 61 FR 9227, March 7, 1996]

1926.305 Jacks - Lever and Ratchet, Screw and Hydraulic

(a) General requirements (a)(1) The manufacturer’s rated capacity shall

be legibly marked on all jacks and shall not be exceeded

(a)(2) All jacks shall have a positive stop to

prevent over travel


(c) Blocking When it is necessary to provide a firm

foundation, the base of the jack shall be blocked or cribbed. Where there is a possibility of slippage of the metal cap of the jack, a wood block shall be placed between the cap and the load.


(d) (d)(1) "Operation and maintenance" (d)(1)(i) After the load has been raised, it shall be cribbed,

blocked, or otherwise secured at once (d)(1)(ii) Hydraulic jacks exposed to freezing temperatures

shall be supplied with an adequate antifreeze liquid (d)(1)(iii) All jacks shall be properly lubricated at regular

intervals


(d)(1)(iv) Each jack shall be thoroughly inspected at times which

depend upon the service conditions. Inspections shall be not less frequent than the following:

(d)(1)(iv)(a) For constant or intermittent use at one locality, once

every 6 months (d)(1)(iv)(b) For jacks sent out of shop for special work, when sent

out and when returned (d)(1)(iv)(c) For a jack subjected to abnormal load or shock,

immediately before and immediately thereafter


(d)(1)(v) Repair or replacement parts shall be

examined for possible defects (d)(1)(vi) Jacks which are out of order shall be

tagged accordingly, and shall not be used until repairs are made

[44 FR 8577, Feb. 9, 1979; 44 FR 20940, Apr. 6, 1979; 55 FR 42328, Oct. 18, 1990; 58 FR 35176, June 30, 1993]

1926.306 Air Receivers (a) "General requirements – (a)(1) "Application." This section applies to compressed air

receivers, and other equipment used in providing and utilizing compressed air for performing operations such as cleaning, drilling, hoisting, and chipping. On the other hand, however, this section does not deal with the special problems created by using compressed air to convey materials nor the problems created when men work in compressed air as in tunnels and caissons. This section is not intended to apply to compressed air machinery and equipment used on transportation vehicles such as steam railroad cars, electric railway cars, and automotive equipment.

1926.306 Air Receivers (a)(2) "New and existing equipment" (a)(2)(i) All new air receivers installed after the effective

date of these regulations shall be constructed in accordance with the 1968 edition of the A.S.M.E. Boiler and Pressure Vessel Code Section VIII

(a)(2)(ii) All safety valves used shall be constructed,

installed and maintained in accordance with the A.S.M.E. Boiler and Pressure Vessel Code, Section VIII Edition 1968

(b) "Installation and equipment requirements" –

(b)(1) "Installation." Air

receivers shall be so installed that all drains, hand holes, and manholes therein are easily accessible. Under no circumstances shall an air receiver be buried underground or located in an inaccessible place

(b)(2) "Drains and traps." A drain pipe

and valve shall be installed at the lowest point of every air receiver to provide for the removal of accumulated oil and water. Adequate automatic traps may be installed in addition to drain valves. The drain valve on the air receiver shall

be opened and the receiver completely drained frequently and at such intervals as to prevent the accumulation of excessive amounts of liquid in the receiver.

(b)(3) "Gages and valves"

(b)(3)(i) Every air receiver shall be

equipped with an indicating pressure gage (so located as to be readily visible) and with one or more spring-loaded safety valves. The total relieving capacity of such safety valves shall be such as to prevent pressure in the receiver from exceeding the maximum allowable working pressure of the receiver by more than 10 percent

(b)(3)(ii) No valve of any type

shall be placed between the air receiver and its safety valve or valves

b)(3) "Gages and valves"

(b)(3)(iii) Safety appliances, such

as safety valves, indicating devices and controlling devices, shall be constructed, located, and installed so that they cannot be readily rendered inoperative by any means, including the elements

(b)(3)(iv) All safety valves shall

be tested frequently and at regular intervals to determine whether they are in good operating condition

[58 FR 35176, June 30, 1993]

1926.307 Mechanical Power-Transmission Apparatus

(A) "GENERAL REQUIREMENTS"

(A) "GENERAL REQUIREMENTS"

(a)(1) This section covers all

types and shapes of power-transmission belts, except the following when operating at two hundred and fifty (250) feet per minute or less:

(a)(1)(i) Flat belts 1 inch (2.54

cm) or less in width

(a)(1)(ii) flat belts 2 inches

(5.08 cm) or less in width which are free from metal lacings or fasteners


(a)(1)(iii) round belts 1/2 inch

(1.27 cm) or less in diameter; and

(a)(1)(iv) single strand V-belts,

the width of which is thirteen thirty-seconds (13/32) inches or less

(a)(2) Vertical and inclined belts

(paragraphs (e)(3) and (4) of this section) if not more than 2 1/2 inches (6.35 cm) wide and running at a speed of less than one thousand (1,000) feet per minute, and if free from metal lacings or fastening may be guarded with a nip-point belt and pulley guard


(a)(3) For the Textile Industry,

because of the presence of excessive deposits of lint, which constitute a serious fire hazard, the sides and face sections only of nip-point belt and pulley guards are required, provided the guard shall extend at least 6 inches (15.24 cm) beyond the rim of the pulley on the in-running

and off-running sides of the belt and at least 2 inches (5.08 cm) away from the rim and face of the pulley in all other directions.

(a)(4) This section covers the

principal features with which power transmission safeguards shall comply.


(B) "PRIME-MOVER GUARDS" -

(b)(1) "Flywheels." Flywheels

located so that any part is 7 feet (2.128 m) or less above floor or platform shall be guarded in accordance with the requirements of this subparagraph:

(b)(1)(i) With an enclosure of sheet,

perforated, or expanded metal, or woven wire

(b)(1)(ii) With guard rails placed not less

than 15 inches (38.1 cm) nor more than 20 inches (50.8 cm) from rim. When flywheel extends into pit or is within 12 inches (30.48 cm) of floor, a standard toe board shall also be provided

(b)(1)(iii) When the upper rim of flywheel

protrudes through a working floor, it shall be entirely enclosed or surrounded by a guardrail and toe board


(b)(1)(iv) For flywheels with smooth rims 5 feet

(1.52 m) or less in diameter, where the preceding methods cannot be applied, the following may be used: A disk attached to the flywheel in such manner as to cover the spokes of the wheel on the exposed side and present a smooth surface and edge, at the same time providing means for periodic inspection. An open space, not exceeding 4 inches (10.16 cm) in width, may be left between the outside edge of the disk and the rim of the wheel if desired, to facilitate turning the wheel over. Where a disk is used, the keys or other dangerous projections not covered by disk shall be cut off or covered. This subdivision does not apply to flywheel with solid web centers.

(b)(1)(v) Adjustable guard to

be used for starting engine or for running adjustment may be provided at the flywheel of gas or oil engines. A slot opening for jack bar will be permitted


(b)(1)(vi) Wherever flywheels are above

working areas, guards shall be installed having sufficient strength to hold the weight of the flywheel in the event of a shaft or wheel mounting failure

(b)(2) "Cranks and connecting rods."

Cranks and connecting rods, when exposed to contact, shall be guarded in accordance with paragraphs (m) and (n) of this section, or by a guardrail as described in paragraph (o)(5) of this section

(b)(3) "Tail rods or extension

piston rods." Tail rods or extension piston rods shall be guarded in accordance with paragraphs (m) and (o) of this section, or by a guardrail on sides and end, with a clearance of not less than 15 (38.1 cm) nor more than 20 inches (50.8 cm) when rod is fully extended


(C) "SHAFTING" - (c)(1) "Installation" (c)(1)(i) Each continuous line

of shafting shall be secured in position against excessive endwise movement

(c)(1)(ii) Inclined and vertical

shafts, particularly inclined, shall be securely held in position against endwise thrust


(c)(2) "Guarding horizontal shafting." (c)(2)(i) All exposed parts of horizontal

shafting 7 feet (2.128 m) or less from floor or working platform, excepting runways used exclusively for oiling, or running adjustments, shall be protected by a stationary casing enclosing shafting completely or by a trough enclosing sides and top or sides and bottom of shafting as location requires

(c)(2)(ii) Shafting under bench machines

shall be enclosed by a stationary casing, or by a trough at sides and top or sides and bottom, as location requires. The sides of the trough shall come within at least 6 inches (15.24 cm) of the underside of table, or if shafting is located near floor within 6 inches (15.24 cm) of floor. In every case the sides of trough shall extend at least 2 inches (5.08 cm) beyond the shafting or

protuberance


(c)(3) "Guarding vertical and

inclined shafting." Vertical and inclined shafting 7 feet (2.128 m) or less from floor or working platform, excepting maintenance runways, shall be enclosed with a stationary casing in accordance with requirements of paragraphs (m) and (o) of this section

(c)(4) "Projecting shafts ends"

(c)(4)(i) Projecting shaft ends shall

present a smooth edge and end and shall not project more than one-half the diameter of the shaft unless guarded by non-rotating caps or safety sleeves

(c)(4)(ii) Unused keyways shall be

filled up or covered


(c)(5) "Power-transmission apparatus

located in basements." All mechanical power transmission apparatus located in basements, towers, and rooms used exclusively for power transmission equipment shall be guarded in accordance with this section, except that the requirements for safeguarding belts, pulleys, and shafting need not be complied with when the following requirements are met:

(c)(5)(i) The basement, tower, or

room occupied by transmission equipment is locked against unauthorized entrance

(c)(5)(ii) The vertical clearance in

passageways between the floor and power transmission beams, ceiling, or any other objects, is not less than 5 ft. 6 in. (1.672 m)


(c)(5)(iii) The intensity of

illumination conforms to the requirements of ANSI A11.1-1965 (R-1970)

(c)(5)(v) The route followed

by the oiler is protected in such manner as to prevent accident


(d) "Pulleys" (d)(1) "Guarding." Pulleys, any parts of which are 7

feet (2.128 m) or less from the floor or working platform, shall be guarded in accordance with the standards specified in paragraphs (m) and (o) of this section. Pulleys serving as balance wheels (e.g., punch presses) on which the point of contact between belt and pulley is more than 6 ft. 6 in. (1.976 m) from the floor or platform may be guarded with a disk covering the spokes.


(d)(2) "Location of pulleys" (d)(2)(i) Unless the distance to the nearest fixed

pulley, clutch, or hanger exceeds the width of the belt used, a guide shall be provided to prevent the belt from leaving the pulley on the side where insufficient clearance exists


(d)(3) "Broken pulleys." Pulleys with cracks, or

pieces broken out of rims, shall not be used (d)(4) "Pulley speeds." Pulleys intended to operate

at rim speed in excess of manufacturers normal recommendations shall be specially designed and carefully balanced for the speed at which they are to operate

(e) "Belt, rope, and chain drives" -

(e)(1) "Horizontal belts and ropes" (e)(1)(i) Where both runs of horizontal belts are 7 feet (2.128

m) or less from the floor level, the guard shall extend to at least 15 inches (38.1 cm) above the belt or to a standard height (see Table O-12), except that where both runs of a horizontal belt are 42 inches (106.68 cm) or less from the floor, the belt shall be fully enclosed

(e)(1)(ii) In power plants or power-development rooms, a

guardrail may be used in lieu of the guard required by paragraph (e)(1)(i) of this section


(e)(2) "Overhead horizontal belts" (e)(2)(i) Overhead horizontal belts, with lower

parts 7 feet (2.128 m) or less from the floor or platform, shall be guarded on sides and bottom in accordance with paragraph (o)(3) of this section


(e)(2)(ii) Horizontal overhead belts more than 7 feet (2.128

m) above floor or platform shall be guarded for their entire length under the following conditions:

(e)(2)(ii)(a) If located over passageways or work places and

traveling 1,800 feet or more per minute (e)(2)(ii)(b) If center to center distance between pulleys is 10

feet (3.04 m) or more (e)(2)(ii)(c) If belt is 8 inches (20.32 cm) or more in width


(e)(2)(iii) Where the upper and lower runs of

horizontal belts are so located that passage of persons between them would be possible, the passage shall be either:

(e)(2)(iii)(a) Completely barred by a guardrail or other

barrier in accordance with paragraphs (m) and (o) of this section or

(e) "Belt, rope, and chain drives"

(e)(2)(iii)(b) Where passage is regarded as necessary,

there shall be a platform over the lower run guarded on either side by a railing completely filled in with wire mesh or other filler, or by a solid barrier. The upper run shall be so guarded as to prevent contact therewith either by the worker or by objects carried by him. In power plants only the lower run of the belt need be guarded.


(e)(2)(iv) Overhead chain and link belt drives are governed by the same

rules as overhead horizontal belts and shall be guarded in the same manner as belts

(e)(3) "Vertical and inclined belts" (e)(3)(i) Vertical and inclined belts shall be enclosed by a guard

conforming to standards in paragraphs (m) and (o) of this section

(e)(3)(ii) All guards for inclined belts shall be arranged in such a manner

that a minimum clearance of 7 feet (2.128 m) is maintained between belt and floor at any point outside of guard


(e)(4) "Vertical belts." Vertical belts running over a lower pulley more

than 7 feet (2.128 m) above floor or platform shall be guarded at the bottom in the same manner as horizontal overhead belts, if conditions are as stated in paragraphs (e)(2)(ii)(a) and (c) of this section

(e)(5) "Cone-pulley belts" (e)(5)(i) The cone belt and pulley shall be equipped with a belt shifter so

constructed as to adequately guard the nip point of the belt and pulley. If the frame of the belt shifter does not adequately guard the nip point of the belt and pulley, the nip point shall be further protected by means of a vertical guard placed in front of the pulley and extending at least to the top of the largest step of the cone


(e)(5)(ii) If the belt is of the endless type or laced with rawhide

laces, and a belt shifter is not desired, the belt will be considered guarded if the nip point of the belt and pulley is protected by a nip point guard located in front of the cone extending at least to the top of the largest step of the cone, and formed to show the contour of the cone in order to give the nip point of the belt and pulley the maximum protection

(e)(5)(iii) If the cone is located less than 3 feet (0.912 m) from the

floor or working platform, the cone pulley and belt shall be guarded to a height of 3 feet (0.912 m) regardless of whether the belt is endless or laced with rawhide


(e)(6) "Belt tighteners" (e)(6)(i) Suspended counterbalanced tighteners and all parts

thereof shall be of substantial construction and securely fastened; the bearings shall be securely capped. Means must be provided to prevent tightener from falling, in case the belt breaks

(e)(6)(ii) When suspended counterweights are used and not

guarded by location, they shall be so encased as to prevent accident

(f) "Gears, sprockets, and chains" -

(f)(1) "Gears." Gears shall be guarded in accordance with one of the

following methods: (f)(1)(i) By a complete enclosure or (f)(1)(ii) By a standard guard as described in paragraph (o) of this section,

at least 7 feet (2.128 m) high extending 6 inches (15.24 cm) above the mesh point of the gears or

(f)(1)(iii) By a band guard covering the face of gear and having flanges

extended inward beyond the root of the teeth on the exposed side or sides. Where any portion of the train of gears guarded by a band guard is less than 6 feet (1.824 m) from the floor a disk guard or a complete exposure to the height of 6 feet (1.824 m) shall be required

(f) "Gears, sprockets, and chains"

(f)(2) "Hand-operated gears." Paragraph (f)(1)

of this section does not apply to hand- operated gears used only to adjust machine parts and which do not continue to move after hand power is removed. However, the guarding of these gears is highly recommended


(f)(3) "Sprockets and chains." All sprocket

wheels and chains shall be enclosed unless they are more than 7 feet (2.128 m) above the floor or platform. Where the drive extends over other machine or working areas, protection against falling shall be provided. This subparagraph does not apply to manually operated sprockets.


(f)(4) "Openings for oiling." When frequent

oiling must be done, openings with hinged or sliding self-closing covers shall be provided. All points not readily accessible shall have oil feed tubes if lubricant is to be added while machinery is in motion

(g) "Guarding friction drives."

The driving point of all friction drives when exposed to contact shall be guarded, all arm or spoke friction drives and all web friction drives with holes in the web shall be entirely enclosed, and all projecting belts on friction drives where exposed to contact shall be guarded

(h) "Keys, setscrews, and other projections"

(h)(1) All projecting keys, setscrews, and other projections

in revolving parts shall be removed or made flush or guarded by metal cover. This subparagraph does not apply to keys or setscrews within gear or sprocket casings or other enclosures, nor to keys, setscrews, or oil cups in hubs of pulleys less than 20 inches (50.8 cm) in diameter where they are within the plane of the rim of the pulley

(h)(2) It is recommended, however, that no projecting

setscrews or oil cups be used in any revolving pulley or part of machinery

(i) "Collars and couplings" (i)(1) "Collars." All revolving collars, including split

collars, shall be cylindrical, and screws or bolts used in collars shall not project beyond the largest periphery of the collar

(i)(2) "Couplings." Shall couplings shall be so constructed

as to present no hazard from bolts, nuts, setscrews will, however, be permitted where they are covered with safety sleeves or where they are used parallel with the shafting and are countersunk or else do not extend beyond the flange of the coupling

(j) "Bearings and facilities for oiling."

All drip cups and pans shall be securely fastened

(k) "Guarding of clutches, cutoff couplings, and clutch pulleys"

(k)(1) "Guards." Clutches, cutoff

couplings, or clutch pulleys having projecting parts, where such clutches are located 7 feet (2.128 m) or less above the floor or working platform, shall be enclosed by a stationary guard constructed in accordance with this section. A "U" type guard is permissible

(k)(2) "Engine rooms." In

engine rooms a guardrail, preferably with toe board, may be used instead of the guard required by paragraph (k)(1) of this section, provided such a room is occupied only by engine room attendants

(l) "Belt shifters, clutches, shippers, poles, perches, and fasteners"

(l)(1) "Belt shifters" (l)(1)(i) Tight and loose pulleys on

all new installations made on or after August 31, 1971, shall be equipped with a permanent belt shifter provided with mechanical means to prevent belt from creeping from loose to tight pulley. It is recommended that old installations be changed to conform to this rule

(l)(1)(ii) Belt shifter and clutch

handles shall be rounded and be located as far as possible from danger of accidental contact, but within easy reach of the operator. Where belt shifter are not directly located over a machine or bench, the handles shall be cut off 6 ft. 6 in. (1.976 m) above floor level

(l) "Belt shifters, clutches, shippers, poles, perches, and fasteners"

(l)(2) "Belt shippers and shipper

poles." The use of belt poles as substitutes for mechanical shifter is not recommended

(l)(3) "Belt perches." Where

loose pulleys or idlers are not practicable, belt perches in form of brackets, rollers, etc., shall be used to keep idle belts away from the shafts

(l)(4) "Belt fasteners." Belts which

of necessity must be shifted by hand and belts within 7 feet (2.128 m) of the floor or working platform which are not guarded in accordance with this section shall not be fastened with metal in any case, nor with any other fastening which by construction or wear will constitute an accident hazard

(m) "Standard guards - general requirements"

(m)(1) Materials (m)(1)(i) Standard conditions shall be

secured by the use of the following materials. Expanded metal, perforated or solid sheet metal, wire mesh on a frame of angle iron, or iron pipe securely fastened to floor or frame of machine

(m)(1)(ii) All metal should be free from

burrs and sharp edges

(m)(2) "Methods of

manufacturer" (m)(2)(i) Expanded metal,

sheet or perforated metal, and wire mesh shall be securely fastened to frame

o) "Approved materials" (o)(1) Minimum

requirements." The materials and dimensions specified in this paragraph shall apply to all guards, except horizontal overhead belts, rope, cable, or chain guards more than 7 feet (2.128 m) above floor, or platform

(o)(1)(i)(a) All guards shall be

rigidly braced every 3 feet (0.912 m) or fractional part of their height to some fixed part of machinery or building structure. Where guard is exposed to contact with moving equipment additional strength may be necessary

o) "Approved materials" (o)(2) "Wood guards" (o)(2)(i) Wood guards may be used in the woodworking

and chemical industries, in industries where the presence of fumes or where manufacturing conditions would cause the rapid deterioration of metal guards; also in construction work and in locations outdoors where extreme cold or extreme heat make metal guards and railings undesirable. In all other industries, wood guards shall not be used.

o) "Approved materials" (o)(3) "Guards for horizontal overhead belts" (o)(3)(i) Guards for horizontal overhead belts shall run

the entire length of the belt and follow the line of the pulley to the ceiling or be carried to the nearest wall, thus enclosing the belt effectively. Where belts are so located as to make it impracticable to carry the guard to wall or ceiling, construction of guard shall be such as to enclose completely the top and bottom runs of belt and the face of pulleys

o) "Approved materials" (o)(3)(iii) Suitable reinforcement shall be provided for the ceiling rafters or

overhead floor beams, where such is necessary, to sustain safely the weight and stress likely to be imposed by the guard. The interior surface of all guards, by which is meant the surface of the guard with which a belt will come in contact, shall be smooth and free from all projections of any character, except where construction demands it;

protruding shallow roundhead rivets may be used. Overhead belt guards shall be at least one quarter wider than belt which they protect, except that this clearance need not in any case exceed 6 inches (15.24 cm) on each side. Overhead rope drive and block and roller-chain-drive guards shall be not less than 6 inches (15.24 cm) wider than the drive on each side. In overhead silent chain-drive guards where the chain is held from lateral displacement on the sprockets, the side clearances required on drives of 20 inch (50.8 cm) centers or under shall be not less than 1/4 inch (0.635 cm) from the nearest moving chain part, and on drives of over 1/2 inch (1.27 cm) from the nearest moving chain part.

o) "Approved materials" (o)(4) "Guards for horizontal overhead rope and

chain drives." Overhead-rope and chain- drive guard construction shall conform to the rules for overhead-belt guard

(o)(5) "Guardrails and toe boards" (o)(5)(i) Guardrail shall be 42 inches (106.68 cm) in

height, with mid rail between top rail and floor

o) "Approved materials" (o)(5)(ii) Posts shall be not more than 8 feet (2.432 m) apart; they are to be

permanent and substantial, smooth, and free from protruding nails, bolts, and splinters. If made of pipe, the post shall be 1 1/4 inches (3.175 cm) inside diameter, or larger. If made of metal shapes or bars their section shall be equal in strength to that of 1 1/2 (3.81 cm) by 1 1/2 (3.81 cm) by 3/16 inch angle iron. If made of wood, the posts

shall be two by four (2 X 4) inches or larger. The upper rail shall be two by four (2 X 4) inches, or two one by four (1 X 4) strips, one at the top and one at the side of posts. The mid rail may be one by four (1 X 4) inches or more. Where panels are fitted with expanded metal or wire mesh as noted in Table O-12 the middle rails may be omitted. Where guard is exposed to contact with moving equipment, additional strength may be necessary

(o)(5)(iii) Toe boards shall be 4 inches (10.16 cm) or more in height, of wood,

metal, or of metal grill not exceeding 1 inch (2.54 cm) mesh

(p) "Care of equipment" (p)(1) "General." All power-transmission equipment shall be inspected at

intervals not exceeding 60 days and be kept in good working condition at all times

(p)(2) "Shafting" (p)(2)(i) Shafting shall be kept in alignment, free from rust and excess oil or

grease (p)(2)(ii) Where explosives, explosive dusts, flammable vapors or flammable

liquids exist, the hazard of static sparks from shafting shall be carefully considered

(p)(3) "Bearings." Bearings shall be kept in alignment and properly

adjusted

(p) "Care of equipment" (p)(4) "Hangers." Hangers shall be inspected to

make certain that all supporting bolts and screws are tight and that supports of hanger boxes are adjusted properly

(p)(5) "Pulleys" (p)(5)(i) Pulleys shall be kept in proper alignment

to prevent belts from running off

Click here to be taken to back to the Exam Page so that you can complete your exam.

You will receive a Certificate of Completion for the course if you complete the exam and receive a grade of 80% per higher.

osha part 1926 safety and health regulations for construction

Documents

tools hand

safety guards

methods of machine guarding

guarding device

tools bar

examples of guarding

safety code

hand tripping devices