OSD Menu 16:9 1200TVL Camera

USER’S MANUAL

Thank you for purchasing our products. Please read the manual carefully before operation

Safety Precaution

This symbol means that there might exist uninsulated dangerous voltage inside the case, be careful of electric shock.

This symbol reminds you to pay attention to important operation and

maintenance instructions in the accompanied information.

WARNING

In order to prevent damage caused by fire or electric shock, please do not put

cameras exposed in the moist environment or rainwater.

Please make sure the adapter is consistent with product specifications, otherwise

it might cause fire, electric shock or damage.

Pay attention to polarity of the adapter, it might cause some accidents like fires.

Please don’t connect multiple cameras with the same adapter at the same time;

overloading of adapter capacity may cause fires.

Power supply must be firmly fixed so as not to loose to cause fires.

If the device gets abnormal smell or smoke”, please stop it immediately and

contact with our customer service center.

If the camera doesn’t work as usual, please do not dismantle it by yourself. Please

contact our local distributor or our maintenance office authorized by our company,

otherwise we won’t promise warranty.

Please do not splash water on the product components when cleaning.

Features

960H CVBS OUTPUT

1.3MGEA SENSOR

1200 TVL

OUTPUT 16：9 IMAGE

3D-DNR

SENSE-UP FUNCTION

OSD FUNCTION

SUPPORT AUDIO

UTC FUNCTION

WORK FROM +5V TO +24V。

Press“Enter”button for 2s, camera screen will pop up system main menu. (eg, pic 1)

1 EXPOSURE

Move the cursor to the main menu function " EXPOSURE" menu item , press the "

LEFT AND RIGHT" button select "STD or BLC"mode.

1.1 STD MODE

press the " ENTER" button enter the sub-menu,can setting camera brightness .

have "low ,middle ,high "three mode to choice.

1.2 BLC MODE

2 SHUTTER MODE

Move the cursor to the main menu function " SHUTTER MODE" menu item , press

the " LEFT AND RIGHT" button select "AUTO or MANUAL"mode. camera normally

work on AUTO mode

2.1 AUTO MODE

SLOWSHUTTER is SENSE UP function,

have serval choice :1X,AUTO,2X,3X,4X,5X,6X,7X,8X,9X.

SLOWSHUTTER more high ,more birght at night.but more ghost

2.2 MANUAL

shutter mode can select from 1/50 to 1/100000

3 AGC MODE

AGC” can adjust the peak value, the bigger value, the brighter picture, but

the noise will be much bigger.

AGC” can adjust the peak value, the bigger value, the brighter picture, but the noise will be much bigger. ”, there are “on” and “off ” are optional the user can press " left and right " set according to actual needs.

4 AWB

It can restore the authenticity of the color when it is affected by the change

of temperature. The user can choose different white balance mode accordingly,

ATW1/ATW2 /ATW3

5 IMAGE ADJ

When the IMAGE is displayed on the screen, could do settings of image function and details. Press the “OK” button to select IMAGE and do settings..

SHARPNESS is the parameter to adjust overall picture sharpness,can set from 0-

100,the value more high ,the picture more sharp.

HDDNR is 2D-DNR function the parameter to adjust overall picture noise, can set

from 0-100.

3DNR it can adjust the level of noise reduction, the bigger the value , the higher

the noise reduction level .and the more the ghost.

CONTARST is the area ratio to adjust the brightest screen and darkest areas. "can

set from 0 to 100.

SATURATION is to adjust bright degree of color. It can set from 0-100. the higher

value,the more deep picture.

PRESS"NEXT" enter next page

this page have three setting,R GAIN ,G GAIN ,B GAIN .The user can adjust the

value change color hue, Users can set different color value according to camera

environment

Press" RETURN "button back to main Menu page

Press "NEXT" button enter to next page .(eg, pic below)

6 DAY NIGHT MODE

day night have four mode,"AUTO,BW,COLOR,EXT" . This function is to select

“color “or “black and white” images through the infrared lamp board control

signal. It is synchronous with infrared lamp’s opening and closing time.

.COLOR mode Image will always be color,BW mode image will always be black

and whiteAUTO mode is control the camera output color or black and white

image according to the strength of the light, can set dayniht delay as picture

below .

7 SYSTEM

Enter the "SYSTEM" sub-menu ,The function “Languages” is for the camera

menu; System comes with “Chinese”"Japanese "“English” three languages for

Users of different nationalities. User can select the language by press “left”

“right” key.

TV SYSTEM

The function “TV system” is for the camera menu; System comes with “PAL

and NTSC” two mode for Users of different nationalities

BAD PIXEL

BAD pixel is for bad pixel repair.USER can repair bad pixel by "ON" and "OFF"mode.

PRIVACY MASK

, user can adjust the size, position, color, transparency of the chosen area

HLC

In “BLC” menu, press “left” “right” key to select “ON” “OFF

8 SAVE

When the user finish the setting and want to save it. Please choose” SAVE ”

and press enter to exit the OSD menu. The setting will be saved in FLASH and will

not loose when the power supply is cut or the system is restarted.

9 EXIT

Press to exit the OSD menu.